Gigabyte GA-880GM-USB3 (rev. 3.1) User Manual [ru]

GA-880GM-USB3

User's Manual

Rev. 3101 12ME-88GMUB3-3101R

dr aobr eht o M

GA-880GM-USB3

Motherboard

GA-880GM-USB3

Mar. 5, 2011

Mar. 5, 2011

Copyright

© 2011 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission.

Documentation Classifications

In order to assist in the use of this product, GIGABYTE provides the following types of documentations:

For quick set-up of the product, read the Quick Installation Guide included with the product.

For detailed product information, carefully read the User's Manual.

For product-related information, check on our website at:

http://www.gigabyte.com.tw

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information.

Example:

Table of Contents

Box Contents....................................................................................................................			6
Optional Items..................................................................................................................			6
GA-880GM-USB3 Motherboard Layout...........................................................................			7
GA-880GM-USB3 Motherboard Block Diagram...............................................................			8
Chapter 1 Hardware Installation......................................................................................			9
1-1	Installation Precautions.....................................................................................		9
1-2	Product Specifications....................................................................................		10
1-3	Installing the CPU and CPU Cooler................................................................		13
1-3-1		Installing the CPU...................................................................................................	13
1-3-2 Installing the CPU Cooler........................................................................................			15
1-4	Installing the Memory......................................................................................		16
1-4-1 Dual Channel Memory Configuration......................................................................			16
1-4-2		Installing a Memory ................................................................................................	17
1-5	Installing an Expansion Card..........................................................................		18
1-6	Setup of the ATI Hybrid CrossFireX™ Configuration.......................................		19
1-7	Back Panel Connectors..................................................................................		20
1-8	Internal Connectors........................................................................................		23
Chapter 2 BIOS Setup...................................................................................................			31
2-1	Startup Screen................................................................................................		32
2-2	The Main Menu...............................................................................................		34
2-3	MB Intelligent Tweaker(M.I.T.)........................................................................		36
2-4	Standard CMOS Features..............................................................................		41
2-5	Advanced BIOS Features...............................................................................		43
2-6	Integrated Peripherals....................................................................................		46
2-7	Power Management Setup.............................................................................		49
2-8	PnP/PCI Configurations..................................................................................		51
2-9	PC Health Status............................................................................................		52
2-10	Load Fail-Safe Defaults..................................................................................		54
2-11	Load Optimized Defaults................................................................................		54
2-12	Set Supervisor/User Password.......................................................................		55
2-13	Save & Exit Setup...........................................................................................		56
2-14	Exit Without Saving.........................................................................................		56

- 4 -

Chapter 3 Drivers Installation........................................................................................			57
3-1	Installing Chipset Drivers................................................................................		57
3-2	Application Software.......................................................................................		58
3-3	Technical Manuals..........................................................................................		58
3-4	Contact...........................................................................................................		59
3-5	System............................................................................................................		59
3-6	Download Center............................................................................................		60
3-7	New Utilities....................................................................................................		60
Chapter 4 Unique Features...........................................................................................			61
4-1	Xpress Recovery2..........................................................................................		61
4-2	BIOS Update Utilities......................................................................................		64
	4-2-1 Updating the BIOS with the Q-Flash Utility.............................................................		64
	4-2-2 Updating the BIOS with the @BIOS Utility..............................................................		67
4-3	EasyTune 6.....................................................................................................		68
4-4	Easy Energy Saver.........................................................................................		69
4-5	Q-Share..........................................................................................................		71
4-6	SMART Recovery...........................................................................................		72
4-7	Auto Green.....................................................................................................		73
4-8	Cloud OC........................................................................................................		74
Chapter 5 Appendix		.......................................................................................................	75
5-1	Configuring .SATA Hard Drive(s) ....................................................................		75
	5-1-1 Configuring the Onboard SATA Controller .............................................................		75
	5-1-2 Installing the SATA RAID/AHCI Driver and Operating System................................		81
5-2 Configuring ................................................................Audio Input and Output			85
	5-2-1 ...................................................................	Configuring 2/4/5.1/7.1 - Channel Audio	85
	5-2-2 ..........................................................................................	Configuring S/PDIF Out	87
	5-2-3 ...........................................................Enabling the Dolby Home Theater Function		88
	5-2-4 .........................................................................	Configuring Microphone Recording	89
	5-2-5 ......................................................................................Using the Sound Recorder		91
5-3	Troubleshooting..............................................................................................		92
	5-3-1 ..................................................................................	Frequently Asked Questions	92
	5-3-2 .....................................................................................	Troubleshooting Procedure	93

- 5 -

Box Contents

GA-880GM-USB3 motherboard

Motherboard driver disk

User's Manual

Quick Installation Guide

Two SATA 3Gb/s cables

I/O Shield

•The box contents above are for reference only and the actual items shall depend on the product package you obtain. The box contents are subject to change without notice.

•The motherboard image is for reference only.

Optional Items

2-port USB 2.0 bracket (Part No. 12CR1-1UB030-5*R) 2-port IEEE 1394a bracket (Part No. 12CF1-1IE008-0*R) 2-port SATA power cable (Part No. 12CF1-2SERPW-0*R) COM port cable (Part No. 12CF1-1CM001-3*R)

- 6 -

GA-880GM-USB3 Motherboard Layout

KB_MS_USB	CPU_FAN

DVI VGA		ATX_12V_2X4		Socket AM3+
HDMI SPDIF
ESATA 1394 USB
USB30	LAN		Etron
			EJ168
AUDIO
		F_AUDIO	PCIEX1	AMD 880G
	Realtek		PCIEX16
	RTL8111E
			PCI1	GA-880GM-USB3	BAT
	CODEC		PCI2	CLR_CMOS	TSB43AB23
	SPDIF_OUT		COM	F_1394_1	SYS_FAN

1_ 2_ 3_ 4_ DDR3 DDR3 DDR3 DDR3 M_BIOS B_BIOS

IT8720

ATX

			F_PANEL
			SATA2_4
AMD SB710
		SATA2 3	SATA2 2
USB3	USB2	USB1 SATA2 1	SATA2 0
F_	F_	F_

- 7 -

GA-880GM-USB3 Motherboard Block Diagram

1 PCI Express x16

CPU CLK+/- (200 MHz)

AM3+/AM3 CPU

DDR3 1800 (O.C.) (Note 1)/

1333/1066 MHz

Dual Channel Memory

PCIe CLK

LAN

2 USB 3.0/2.0

(100 MHz)

Hyper Transport 3.0

RJ45

Realtek

Etron

GFX CLK (100 MHz)

RTL8111E

EJ168

x16

x1

x1

AMD 880G

D-Sub

PCI Express Bus

x1

DVI-D (Note 2)

HDMI (Note 2)

PCIe CLK

(100 MHz)

1 PCI Express x1

6 SATA 3Gb/s

10 USB Ports

PCI Bus

AMD SB710

Dual BIOS

LPC

TSB43AB23

Bus

iTE

COM Port

IT8720

CODEC

PS/2 KB/Mouse

2 IEEE 1394a

2 PCI

PCI CLK

(33 MHz)

Out Out	MIC	Line	Out
Out		In
		Out	S/PDIF
Speaker Speaker Speaker		Line
Center/Subwoofer Side
Surround

(Note 1) To reach DDR3 1800 MHz or above, you must install two memory modules and install them in the DDR3_3 and DDR3_4 memory sockets.

(Note 2) Simultaneous output for DVI-D and HDMI is not supported. - 8 -

Chapter 1 Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures:

•Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or warranty sticker provided by your dealer. These stickers are required for warranty validation.

•Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.

•When connecting hardware components to the internal connectors on the motherboard, make sure they are connected tightly and securely.

•When handling the motherboard, avoid touching any metal leads or connectors.

•It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity.

•Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container.

•Before unplugging the power supply cable from the motherboard, make sure the power supply has been turned off.

•Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard.

•Before using the product, please verify that all cables and power connectors of your hardware components are connected.

•To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components.

•Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.

•Do not place the computer system on an uneven surface.

•Do not place the computer system in a high-temperature environment.

•Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user.

•If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician.

- 9 -

Hardware Installation

1-2	Product Specifications
	CPU		AM3+ Socket:
			- AMD AM3+ processor
			- AMD AM3 Phenom™ II processor/ AMD Athlon™ II processor
			(Go to GIGABYTE's website for the latest CPU support list.)
	Hyper Transport		5200 MT/s
	Bus
	Chipset	North Bridge: AMD 880G
		South Bridge: AMD SB710
	Memory	4 x 1.5V DDR3 DIMM sockets supporting up to 16 GB of system memory

* Due to Windows 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than 4 GB.

		Dual channel memory architecture
		Support for DDR3 1800 (O.C.)/1333/1066 MHz memory modules
			* To reach DDR3 1800 MHz or above, you must install two memory modules and install
			them in the DDR3_3 and DDR3_4 memory sockets.
		(Go to GIGABYTE's website for the latest supported memory speeds and memory
		modules.)
Onboard		North Bridge:
Graphics		-	1 x D-Sub port
		-	1 x DVI-D port, supporting a maximum resolution of 1920x1200
			* The DVI-D port does not support D-Sub connection by adapter.
		-	1 x HDMI port, supporting a maximum resolution of 1920x1200
			* Simultaneous output for DVI-D and HDMI is not supported.
Audio		Realtek ALC889 codec
		High Definition Audio
		2/4/5.1/7.1-channel
		Support for Dolby® Home Theater
		Support for S/PDIF Out
LAN		1 x Realtek RTL8111E chip (10/100/1000 Mbit)
Expansion Slots		1 x PCI Express x16 slot, running at x16
		1 x PCI Express x1 slot
		(All PCI Express slots conform to the PCI Express 2.0 standard.)
		2 x PCI slots
Multi-Graphics		Support for ATI Hybrid CrossFireX™ technology
Technology
Storage Interface		South Bridge:
		-	5 x SATA 3Gb/s connectors supporting up to 5 SATA 3Gb/s devices
		-	1 x eSATA 3Gb/s port on the back panel supporting up to 1 SATA 3Gb/s
			device
		-	Support for SATA RAID 0, RAID 1, RAID 10, and JBOD

Hardware Installation

- 10 -

USB		South Bridge:
		-	Up to 10 USB 2.0/1.1 ports (4 on the back panel, 6 via the USB brackets
			connected to the internal USB headers)
		Etron EJ168 chip:
		-	Up to 2 USB 3.0/2.0 ports on the back panel
IEEE 1394		T.I. TSB43AB23 chip:
		-	Up to 2 IEEE 1394a ports (1 on the back panel, 1 via the IEEE 1394a bracket
			connected to the internal IEEE 1394a header)
Internal		1 x 24-pin ATX main power connector
Connectors		1 x 8-pin ATX 12V power connector
	5 x SATA 3Gb/s connectors
	1 x CPU fan header
	1 x system fan header
	1 x front panel header
	1 x front panel audio header
	1 x S/PDIF Out header
	3 x USB 2.0/1.1 headers
	1 x IEEE 1394a header
	1 x serial port header
	1 x clearing CMOS jumper
Back Panel		1 x PS/2 keyboard/mouse port
Connectors		1 x D-Sub port
	1 x DVI-D port
	1 x HDMI port
	1 x optical S/PDIF Out connector
	1 x eSATA 3Gb/s port
	4 x USB 2.0/1.1 ports
	2 x USB 3.0/2.0 ports
	1 x RJ-45 port
	6 x audio jacks (Center/Subwoofer Speaker Out/Rear Speaker Out/Side Speaker
		Out/Line In/Line Out/Microphone)
I/O Controller		iTE IT8720 chip
Hardware		System voltage detection
Monitor		CPU/System temperature detection

CPU/System fan speed detectionCPU overheating warning

CPU/System fan fail warningCPU/System fan speed control

*Whether the CPU/system fan speed control function is supported will depend on the CPU/system cooler you install.

- 11 -

Hardware Installation

	BIOS		2 x 16 Mbit flash
		Use of licensed AWARD BIOS
		Support for DualBIOS™
		PnP 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.0b
	Unique Features		Support for @BIOS
			Support for Q-Flash
		Support for Xpress BIOS Rescue
		Support for Download Center
		Support for Xpress Install
		Support for Xpress Recovery2
		Support for EasyTune
			* Available functions in EasyTune may differ by motherboard model.
		Support for Easy Energy Saver
		Support for Smart Recovery
		Support for Auto Green
		Support for ON/OFF Charge
		Support for Cloud OC
			Support for Q-Share
	Bundled	Norton Internet Security (OEM version)
	Software
	Operating	Support for Microsoft® Windows 7/Vista/XP
	System
	Form Factor		Micro ATX Form Factor; 24.4cm x 24.4cm

*GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice.

Hardware Installation

- 12 -

1-3 Installing the CPU and CPU Cooler

Read the following guidelines before you begin to install the CPU:

•Make sure that the motherboard supports the CPU.

(Go to GIGABYTE's website for the latest CPU support list.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage.

•Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may locate the notches on both sides of the CPU and alignment keys on the CPU socket.)

•Apply an even and thin layer of thermal grease on the surface of the CPU.

•Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage of the CPU may occur.

•Set the CPU host frequency in accordance with the CPU specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals. If you wish to set the frequency beyond the standard specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc.

1-3-1 Installing the CPU

A. Locate the pin one (denoted by a small triangle) of the CPU socket and the CPU.

A Small Triangle Mark

AM3+ Socket

Denotes Pin One of the

Socket

A Small Triangle Marking	AM3+/AM3 CPU
Denotes CPU Pin One

- 13 -

Hardware Installation

B.Follow the steps below to correctly install the CPU into the motherboard CPU socket.

•Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU.

•Do not force the CPU into the CPU socket. The CPU cannot fit in if oriented incorrectly. Adjust the

CPU orientation if this occurs.

CPU Socket

Locking Lever

Step 1:

Completely lift up the CPU socket locking lever.

Step 2:

Align the CPU pin one (small triangle marking) with the triangle mark on the CPU socket and gently insert the CPU into the socket. Make sure that the CPU pins fit perfectly into their holes. Once the CPU is positioned into its socket, place one finger down on the middle of the

CPU, lowering the locking lever and latching it into the fully locked position.

Hardware Installation

- 14 -

1-3-2 Installing the CPU Cooler

Follow the steps below to correctly install the CPU cooler on the CPU. (The following procedure uses the GIGABYTE cooler as the example.)

Step 1:

Apply an even and thin layer of thermal grease on the surface of the installed CPU.

Step 3:

Hook the CPU cooler clip to the mounting lug on one side of the retention frame. On the other side,push straight down on the the CPU cooler clip to hook it to the mounting lug on the retention frame.

Step 2:

Place the CPU cooler on the CPU.

Step 4:

Turn the cam handle from the left side to the right side (as the picture above shows) to lock into place. (Refer to your CPU cooler installation manual for instructions on installing the cooler.)

Step 5:

Finally, attach the power connector of the CPU cooler to the CPU fan header (CPU_FAN) on the motherboard.

Use extreme care when removing the CPU cooler because the thermal grease/tape between the CPU cooler and CPU may adhere to the CPU. Inadequately removing the CPU cooler may damage the CPU.

- 15 -

Hardware Installation

1-4 Installing the Memory

Read the following guidelines before you begin to install the memory:

•Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used.

(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.

•Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.

1-4-1 Dual Channel Memory Configuration

This motherboard provides four DDR3 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual Channel memory mode will double the original memory bandwidth.

The four DDR3 memory sockets are divided into two channels and each channel has two memory sockets as following:

Channel 0: DDR3_1, DDR3_3 Channel 1: DDR3_2, DDR3_4

Dual Channel Memory Configurations Table

							DDR3_1	DDR3_2	DDR3_3	DDR3_4
						Two Modules	DS/SS	DS/SS	- -	- -
							- -	- -	DS/SS	DS/SS
						Four Modules	DS/SS	DS/SS	DS/SS	DS/SS

(SS=Single-Sided, DS=Double-Sided, "- -"=No Memory)

If two memory modules are to be installed, it is recommended that you install them in the DDR3_1 and DDR3_2 sockets.

DDR3_4

DDR3_3

DDR3_2

DDR3_1

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.

1.Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.

2.When enabling Dual Channel mode with two or four memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used and installed in the same colored DDR3 sockets for optimum performance.

Hardware Installation

- 16 -

1-4-2 Installing a Memory

Before installing a memory module, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module.

DDR3 and DDR2 DIMMs are not compatible to each other or DDR DIMMs. Be sure to install DDR3 DIMMs on this motherboard.

Notch

DDR3 DIMM

A DDR3 memory module has a notch, so it can only fit in one direction. Follow the steps below to correctly install your memory modules in the memory sockets.

Step 1:

Note the orientation of the memory module. Spread the retaining clips at both ends of the memory socket. Place the memory module on the socket. As indicated in the picture on the left, place your fingers on the top edge of the memory, push down on the memory and insert it vertically into the memory socket.

Step 2:

The clips at both ends of the socket will snap into place when the memory module is securely inserted.

- 17 -

Hardware Installation

1-5 Installing an Expansion Card

Read the following guidelines before you begin to install an expansion card:

•Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card.

•Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage.

PCI Express x1 Slot

PCI Express x16 Slot

PCI Slot

Follow the steps below to correctly install your expansion card in the expansion slot.

1.Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel.

2.Align the card with the slot, and press down on the card until it is fully seated in the slot.

3.Make sure the metal contacts on the card are completely inserted into the slot.

4.Secure the card’s metal bracket to the chassis back panel with a screw.

5.After installing all expansion cards, replace the chassis cover(s).

6.Turn on your computer. If necessary, go to BIOS Setup to make any required BIOS changes for your expansion card(s).

7.Install the driver provided with the expansion card in your operating system.

Example: Installing and Removing a PCI Express Graphics Card:

• Installing a Graphics Card:

Gently push down on the top edge of the card until it is fully inserted into the PCI Express slot. Make sure the card is securely seated in the slot and does not rock.

•Removing the Card from the PCIEX16_1 slot:

Gently push back on the lever on the slot and then lift the card straight out from the slot.

Hardware Installation

- 18 -

1-6 Setup of the ATI Hybrid CrossFireX™ Configuration

Combining the onboard GPU with a discrete graphics card, ATI Hybrid CrossFireX can provide significantly advanced display performance for AMD platform. Read the following instructions on configuring an ATI Hybrid

CrossFireX system.

A.System Requirements

-Windows 7/Vista operating system

-An ATI Hybrid CrossFireX-supported motherboard and correct driver

-An ATI Hybrid CrossFireX-supported graphics card (Note 1)

B.Connecting the Graphics Cards

Step 1:

Observe the steps in "1-5 Installing an Expansion Card" and install an ATI Hybrid CrossFireX-supported graphics card on the PCIEX16 slot.

Step 2:

Plug the display cable into the onboard graphics port on the back panel.

C. BIOS Setup

Enter BIOS Setup to set the following items under the Advanced BIOS Features menu:

-Set Internal Graphics Mode to UMA. (Note 2)

-Set UMA Frame Buffer Size to 256MB or 512MB. (Note 2)

-Set Surround View to Disabled.

-Set Init Display First to OnChipVGA.

D. Configuring the Graphics Driver

After installing the motherboard driver in the operating system, go to the ATI Catalyst™ Control Center. Select CrossFire™ on the

Graphics menu on the upper left corner and ensure the Enable CrossFire™ check box is selected.

(Note 1) You do not have to install the graphics card driver if the motherboard chipset driver has been installed.

(Note 2) To change the Internal Graphics Mode or UMA Frame Buffer Size setting in BIOS Setup, be sure to disable the CrossFire function in the operating system first.

- 19 -

Hardware Installation

1-7 Back Panel Connectors

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.

PS/2 Keyboard/Mouse Port

Use this port to connect a PS/2 mouse or keyboard.

D-Sub Port

The D-Sub port supports a 15-pin D-Sub connector. Connect a monitor that supports D-Sub connection to this port.

DVI-D Port (Note 1) (Note 2)

The DVI-D port conforms to the DVI-D specification and supports a maximum resolution of 1920x1200

(the actual resolutions supported depend on the monitor being used). Connect a monitor that supports DVI-D connection to this port.

Optical S/PDIF Out Connector

This connector provides digital audio out to an external audio system that supports digital optical audio. Before using this feature, ensure that your audio system provides an optical digital audio in connector.

HDMI Port (Note 2)

The HDMI (High-Definition Multimedia Interface) provides an all-digital audio/video interface to transmit the uncompressed audio/video signals and is HDCP compliant. Connect the HDMI audio/video device to this port. The HDMI Technology can support a maximum resolution of 1920x1200 but the actual resolutions supported depend on the monitor being used.

• After installing the HDMI device, make sure the default device for sound playback is the HDMI device. (The item name may differ by operating system. The following screen is from Windows Vista.)

•Please note the HDMI audio output only supports AC3, DTS and 2-channel-LPCM formats. (AC3 and DTS require the use of an external decoder for decoding.)

In Windows Vista, select Start>Control Panel>Sound, select Realtek

HDMI Output and then click Set Default.

(Note 1) The DVI-D port does not support D-Sub connection by adapter. (Note 2) Simultaneous output for DVI-D and HDMI is not supported.

Hardware Installation

- 20 -

A. Dual Display Configurations:

This motherboard provides three ports for video output: DVI-D, HDMI and D-Sub. The table below shows the supported dual display configurations.

Dual	Combination	Supported or Not
Display	DVI-D + D-Sub	Yes
	DVI-D + HDMI	No
	HDMI + D-Sub	Yes

B. Playback of HD DVD and Blu-ray Discs:

In order to get better playback quality, when playing the HD DVD or Blu-ray discs, refer to the recommended system requirements (or better) below.

•Memory: Two 1 GB DDR3 1066 memory modules with dual channel mode enabled

•BIOS Setup: At least 256 MB of UMA Frame Buffer Size (refer to Chapter 2, "BIOS Setup," "Advanced BIOS Features," for more information)

•Playback software: CyberLink PowerDVD 8.0 or later (Note: Please ensure Hardware Acceleration is enabled.)

•HDCP compliant monitor(s)

IEEE 1394a Port

The IEEE 1394 port supports the IEEE 1394a specification, featuring high speed, high bandwidth and hotplug capabilities. Use this port for an IEEE 1394a device.

eSATA 3Gb/s Port

The eSATA 3Gb/s port conforms to SATA 3Gb/s standard and is compatible with SATA 1.5Gb/s standard. Use the port to connect an external SATA device or a SATA port multiplier.

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.

Connection/

Activity LED

Connection/Speed LED:

Activity LED:

Speed LED

State

Description

State

Description

Orange

1 Gbps data rate

Blinking

Data transmission or receiving is occurring

Green

100 Mbps data rate

Off

No data transmission or receiving is occurring

LAN Port

Off

10 Mbps data rate

USB 3.0/2.0 Port

The USB 3.0 port supports the USB 3.0 specification and is compatible to the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.

•When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard.

•When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.

- 21 -

Hardware Installation

Center/Subwoofer Speaker Out Jack (Orange)

Use this audio jack to connect center/subwoofer speakers in a 5.1/7.1-channel audio configuration.

Rear Speaker Out Jack (Black)

Use this audio jack to connect rear speakers in a 7.1-channel audio configuration.

Side Speaker Out Jack (Gray)

Use this audio jack to connect side speakers in a 4/5.1/7.1-channel audio configuration.

Line In Jack (Blue)

The default line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out Jack (Green)

The default line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to connect front speakers in a 4/5.1/7.1-channel audio configuration.

Mic In Jack (Pink)

The default Mic in jack. Microphones must be connected to this jack.

In addition to the default speakers settings, the ~audio jacks can be reconfigured to perform different functions via the audio software. Only microphones still MUST be connected to the default Mic in jack (). Refer to the instructions on setting up a 2/4/5.1/7.1-channel audio configuration in Chapter 5, "Configuring 2/4/5.1/7.1-Channel Audio."

Hardware Installation

- 22 -

1-8 Internal Connectors

1 3

						2
						8
	9
						6
	10
	13	5	12	7	4	11
1)	ATX_12V_2X4			8)	F_PANEL
2)	ATX			9)	F_AUDIO
3)	CPU_FAN			10)	SPDIF_O
4)	SYS_FAN			11)	F_USB1/F_USB2/F_USB3
5)	CLR_CMOS			12)	F_1394_1
6)	SATA2_0/1/2/3/4			13)	COM
7)	BAT

Read the following guidelines before connecting external devices:

•First make sure your devices are compliant with the connectors you wish to connect.

•Before installing the devices, be sure to turn off the devices and your computer. Unplug the power cord from the power outlet to prevent damage to the devices.

•After installing the device and before turning on the computer, make sure the device cable has been securely attached to the connector on the motherboard.

- 23 -

Hardware Installation

1/2) ATX_12V_2X4/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, first make sure the power supply is turned off and all devices are properly installed. The power connector possesses a foolproof design. Connect the power supply cable to the power connector in the correct orientation. The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will not start.

To meet expansion requirements, it is recommended that a power supply that can withstand high power consumption be used (500W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system.

					ATX_12V_2X4:
			1	5	Pin No.	Definition
					1	GND (Only for 2x4-pin 12V)
					2	GND (Only for 2x4-pin 12V)
			4	8	3	GND
					4	GND
			ATX_12V_2X4		5	+12V (Only for 2x4-pin 12V)
					6	+12V (Only for 2x4-pin 12V)
					7	+12V
					8	+12V
		ATX:
12	24	Pin No.	Definition		Pin No.	Definition
		1	3.3V		13	3.3V
		2	3.3V		14	-12V
		3	GND		15	GND
		4	+5V		16	PS_ON (soft On/Off)
		5	GND		17	GND
		6	+5V		18	GND
		7	GND		19	GND
		8	Power Good		20	-5V
		9	5VSB (stand by +5V)		21	+5V
		10	+12V		22	+5V
		11	+12V (Only for 2x12-pin ATX)		23	+5V (Only for 2x12-pin ATX)
1	13	12	3.3V (Only for 2x12-pin ATX)		24	GND (Only for 2x12-pin ATX)

ATX

Hardware Installation

- 24 -

3/4) CPU_FAN/SYS_FAN (Fan Headers)

The motherboard has a 4-pin CPU fan header (CPU_FAN)and a 4-pin system fan header(SYS_FAN). Each fan header supplies a +12V power voltage and possesses a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation. Most fans are designed with colorcoded power connector wires. A red power connector wire indicates a positive connection and requires a +12V voltage. The black connector wire is the ground wire. The motherboard supports CPU fan speed control, which requires the use of a CPU fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

CPU_FAN:

Pin No.

Definition

1

1

GND

2

+12V /Speed Control

CPU_FAN

3

Sense

4

Speed Control

SYS_FAN:

Pin No.

Definition

1

1

GND

2

+12V /Speed Control

SYS_FAN

3

Sense

4

Reserve

•• Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating may result in damage to the CPU or the system may hang.

•• These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.

5)CLR_CMOS (Clearing CMOS Jumper)

Use this jumper to clear the CMOS values (e.g. date information and BIOS configurations) and reset the CMOS values to factory defaults. To clear the CMOS values, place a jumper cap on the two pins to temporarily short the two pins or use a metal object like a screwdriver to touch the two pins for a few seconds.

Open: Normal

Short: Clear CMOS Values

•• Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values.

•• After clearing the CMOS values and before turning on your computer, be sure to remove the jumper cap from the jumper. Failure to do so may cause damage to the motherboard.

•• After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or manually configure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS configurations).

- 25 -

Hardware Installation

6)SATA2_0/1/2/3/4 (SATA 3Gb/s Connectors, Controlled by AMD SB710 South Bridge)

The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. The AMD SB710 South Bridge supports RAID 0,

RAID 1, RAID 10, and JBOD. Refer to Chapter 5, "Configuring SATA Hard Drive(s)," for instructions on configuring a RAID array.

SATA2_4
7	1
1	7
SATA2_3	SATA2_2
SATA2_1	SATA2_0
7	1

• ARAID0orRAID1configuration requiresatleasttwohard drives. If more than two hard drives are to be used, the total number of hard drives must be an even number.

• A RAID 10 configuration requires four hard drives.

Pin No.	Definition
1	GND
2	TXP
3	TXN
4	GND
5	RXN
6	RXP
7	GND

Please connect the L-shaped end of the SATA cable to your SATA hard drive.

7)BAT (Battery)

The battery provides power to keep the values (such as BIOS configurations, date, and time information) in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery:

1.Turn off your computer and unplug the power cord.

2.Gently remove the battery from the battery holder and wait for one minute. (Or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder, making them short for 5 seconds.)

3.Replace the battery.

4.Plug in the power cord and restart your computer.

•Always turn off your computer and unplug the power cord before replacing the battery.

•Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with an incorrect model.

•Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain about the battery model.

•When installing the battery, note the orientation of the positive side (+) and the negative side (-) of the battery (the positive side should face up).

•Used batteries must be handled in accordance with local environmental regulations.

Hardware Installation

- 26 -

8)F_PANEL (Front Panel Header)

Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

20

19

SPEAK-

PWR-

Speaker

SPEAK+

PWR+

Power LED

CI+

Chassis Intrusion

PW

-

CI-

Header

Power

RES+

Reset

Switch

PW+

RES-

Switch

Message/Power/

MSG-

HD-

Hard Drive

Sleep LED

MSG+

HD+

Activity LED

2

1

• MSG/PWR (Message/Power/Sleep LED, Yellow/Purple):

System Status	LED	Connects to the power status indicator on the chassis front panel. The LED
S0	On	is on when the system is operating. The LED keeps blinking when the sys-
S1	Blinking	tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep
S3/S4/S5	Off	state or powered off (S5).

•PW (Power Switch, Red):

Connects to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management Setup," for more information).

•SPEAK (Speaker, Orange):

Connects to the speaker on the chassis front panel. The system reports system startup status by issuing a beep code. One single short beep will be heard if no problem is detected at system startup. If a problem is detected, the BIOS may issue beeps in different patterns to indicate the problem. Refer to Chapter 5, "Troubleshooting," for information about beep codes.

•HD (Hard Drive Activity LED, Blue)

Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.

•RES (Reset Switch, Green):

Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.

•CI (Chassis Intrusion Header, Gray):

Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has been removed. This function requires a chassis with a chassis intrusion switch/sensor.

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.

- 27 -

Hardware Installation

9)F_AUDIO (Front Panel Audio Header)

The front panel audio header supports Intel High Definition audio (HD) and AC'97 audio. You may connect your chassis front panel audio module to this header. Make sure the wire assignments of the module connector match the pin assignments of the motherboard header. Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it.

									For HD Front Panel Audio:		For AC'97 Front Panel Audio:
									Pin No.	Definition		Pin No.	Definition
		10						9
									1	MIC2_L		1	MIC
		2						1	2	GND		2	GND
									3	MIC2_R		3	MIC Power
									4	-ACZ_DET		4	NC
									5	LINE2_R		5	Line Out (R)
									6	GND		6	NC
									7	FAUDIO_JD		7	NC
									8	No Pin		8	No Pin
									9	LINE2_L		9	Line Out (L)
									10	GND		10	NC

•The front panel audio header supports HD audio by default. If your chassis provides an AC'97 front panel audio module, refer to the instructions on how to activate AC'97 functionality via the audio software in Chapter 5, "Configuring 2/4/5.1/7.1-Channel Audio."

•Audio signals will be present on both of the front and back panel audio connections simultaneously. If you want to mute the back panel audio (only supported when using an HD front panel audio module), refer to Chapter 5, "Configuring 2/4/5.1/7.1-Channel Audio."

•Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug. For information about connecting the front panel audio module that has different wire assignments, please contact the chassis manufacturer.

10)SPDIF_O (S/PDIF Out Header)

This header supports digital S/PDIF Out and connects a S/PDIF digital audio cable (provided by expansion cards) for digital audio output from your motherboard to certain expansion cards like graphics cards and sound cards. For example, some graphics cards may require you to use a S/PDIF digital audio cable for digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display to the graphics card and have digital audio output from the HDMI display at the same time. For information about connecting the S/PDIF digital audio cable, carefully read the manual for your expansion card.

1	Pin No.	Definition
	1	SPDIFO
	2	GND

Hardware Installation

- 28 -

11)F_USB1/F_USB2/F_USB3 (USB Headers)

The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

									Pin No.	Definition
									1	Power (5V)
		10						9	2	Power (5V)
									3	USB DX-
							2	1	4	USB DY-
									5	USB DX+
									6	USB DY+
									7	GND
									8	GND
									9	No Pin
									10	NC

When the system is in S4/S5 mode, only the USB ports routed to the F_USB1 header can support the ON/OFF Charge function.

•Do not plug the IEEE 1394 bracket (2x5-pin) cable into the USB header.

•Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB bracket.

12)F_1394_1 (IEEE 1394a Header)

The header conforms to IEEE 1394a specification. The IEEE 1394a header can provide one IEEE 1394a port via an optional IEEE 1394a bracket. For purchasing the optional IEEE 1394a bracket, please contact the local dealer.

															Pin No.	Definition
								9						1	1	TPA+
		10												2	2	TPA-
															3	GND
															4	GND
															5	TPB+
															6	TPB-
															7	Power (12V)
															8	Power (12V)
															9	No Pin
															10	GND

•Do not plug the USB bracket cable into the IEEE 1394a header.

•Prior to installing the IEEE 1394a bracket, be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the IEEE 1394a bracket.

•To connect an IEEE 1394a device, attach one end of the device cable to your computer and then attach the other end of the cable to the IEEE 1394a device. Ensure that the cable is securely connected.

- 29 -

Hardware Installation

13)COM (Serial Port Header)

The COM header can provide one serial port via an optional COM port cable. For purchasing the optional COM port cable, please contact the local dealer.

												Pin No.	Definition
												1	NDCD-
		9									1	2	NSIN
		10									2	3	NSOUT
												4	NDTR-
												5	GND
												6	NDSR-
												7	NRTS-
												8	NCTS-
												9	NRI-
												10	No Pin

Hardware Installation

- 30 -