Gigabyte GA-990FXA-UD5 Manual

0 (0)

GA-990FXA-UD5

User's Manual

Rev. 1001

12ME-990FXA5-1001R

May 20, 2011

Motherboard

GA-990FXA-UD5

May 20, 2011

Motherboard

GA-990FXA-UD5

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE with-

out prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without GIGABYTE's prior written permission.

Documentation Classications

In order to assist in the use of this product, GIGABYTE provides the following types of documentations:



For quick set-up of the product, read the Quick Installation Guide included with the product.



For detailed product information, carefully read the User's Manual.

For product-related information, check on our website at:

http://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0"

means the revision of the motherboard is 1.0. Check your motherboard revision before updating

motherboard BIOS, drivers, or when looking for technical information.

Example:

- 4 -

Table of Contents

Box Contents ...................................................................................................................6

Optional Items .................................................................................................................6

GA-990FXA-UD5 Motherboard Layout ............................................................................7

GA-990FXA-UD5 Motherboard Block Diagram ...............................................................8

Chapter 1 Hardware Installation .....................................................................................9

1-1 Installation Precautions ....................................................................................9

1-2 Product Specications .................................................................................... 10

1-3 Installing the CPU and CPU Cooler ............................................................... 13

1-3-1 Installing the CPU ...................................................................................................13

1-3-2 Installing the CPU Cooler .......................................................................................15

1-4 Installing the Memory .....................................................................................16

1-4-1 Dual Channel Memory Conguration .....................................................................16

1-4-2 Installing a Memory ...............................................................................................17

1-5 Installing an Expansion Card ......................................................................... 18

1-6 Setup of AMD CrossFireX

™

Conguration...................................................... 19

1-7 Back Panel Connectors .................................................................................. 20

1-8 Internal Connectors ........................................................................................ 22

Chapter 2 BIOS Setup ..................................................................................................31

2-1 Startup Screen ............................................................................................... 32

2-2 The Main Menu .............................................................................................. 33

2-3 MB Intelligent Tweaker(M.I.T.) ........................................................................ 35

2-4 Standard CMOS Features .............................................................................. 41

2-5 Advanced BIOS Features .............................................................................. 43

2-6 Integrated Peripherals .................................................................................... 45

2-7 Power Management Setup ............................................................................. 49

2-8 PC Health Status ............................................................................................ 51

2-9 Load Fail-Safe Defaults .................................................................................. 53

2-10 Load Optimized Defaults ................................................................................ 53

2-11 Set Supervisor/User Password ...................................................................... 54

2-12 Save & Exit Setup .......................................................................................... 55

2-13 Exit Without Saving ........................................................................................ 55

- 5 -

Chapter 3 Drivers Installation ........................................................................................57

3-1 Installing Chipset Drivers ............................................................................... 57

3-2 Application Software ...................................................................................... 58

3-3 Technical Manuals .......................................................................................... 58

3-4 Contact ........................................................................................................... 59

3-5 System ........................................................................................................... 59

3-6 Download Center ........................................................................................... 60

3-7 New Utilities ................................................................................................... 60

Chapter 4 Unique Features ...........................................................................................61

4-1 Xpress Recovery2 .......................................................................................... 61

4-2 BIOS Update Utilities ..................................................................................... 64

4-2-1 Updating the BIOS with the Q-Flash Utility .............................................................64

4-2-2 Updating the BIOS with the @BIOS Utility .............................................................67

4-3 EasyTune 6 .................................................................................................... 68

4-4 Easy Energy Saver ........................................................................................ 69

4-5 Q-Share .......................................................................................................... 71

4-6 SMART Recovery........................................................................................... 72

4-7 Auto Green ..................................................................................................... 73

4-8 Cloud OC ....................................................................................................... 74

Chapter 5 Appendix ......................................................................................................75

5-1 Conguring SATA Hard Drive(s) .................................................................... 75

5-1-1 Conguring AMD SB950 SATA Controllers ............................................................75

5-1-2 Conguring Marvell 88SE9172 SATA Controllers ...................................................81

5-1-3 Installing the SATA RAID/AHCI Driver and Operating System ...............................87

5-2 Conguring Audio Input and Output ............................................................... 95

5-2-1 Conguring 2/4/5.1/7.1-Channel Audio ...................................................................95

5-2-2 Conguring S/PDIF Out ..........................................................................................97

5-2-3 Enabling the Dolby Home Theater Function ...........................................................98

5-2-4 Conguring Microphone Recording ........................................................................99

5-2-5 Using the Sound Recorder ...................................................................................101

5-3 Troubleshooting............................................................................................ 102

5-3-1 Frequently Asked Questions ................................................................................102

5-3-2 Troubleshooting Procedure ..................................................................................103

- 6 -

Box Contents

GA-990FXA-UD5 motherboard

Motherboard driver disk

User's Manual

Quick Installation Guide

Four SATA cables

I/O Shield

One 2-Way SLI bridge connector

(Note)

One 3-Way SLI bridge connector

(Note)

Optional Items

2-port USB 2.0 bracket (Part No. 12CR1-1UB030-5*R)

2-port SATA power cable (Part No. 12CF1-2SERPW-0*R)

COM port cable (Part No. 12CF1-1CM001-3*R)

2-port IEEE 1394a bracket (Part No. 12CF1-1IE008-0*R)

3.5" Front Panel with 2 USB 3.0/2.0 ports (Part No. 12CR1-FPX582-0*R)

• The box contents above are for reference only and the actual items shall depend on the product package you obtain.

The box contents are subject to change without notice.

• The motherboard image is for reference only.

(Note) To enable NVIDIA SLI technology, you need SLI-supported graphics cards, BIOS, and driver. For more

details, please go to GIGABYTE's website.

- 7 -

GA-990FXA-UD5 Motherboard Layout

(Note) Due to a hardware limitation, the PCIEX1 slot can only accommodate a shorter PCI Express x1

expansion card. For a longer expansion card, use other expansion slots.

KB_MS_USB

CPU_FAN

ATX

GA-990FXA-UD5

AUDIO

SYS_FAN1

DDR3_4

DDR3_2

ATX_12V

AMD 990FX

AMD SB950

CODEC

BAT

PCI

F_USB2

M_BIOS

F_PANEL

B_BIOS

F_USB1

PCIEX16_1

USB_ESATA

CLR_CMOS

SPDIF_O

Socket AM3+

Realtek

RTL8111E

iTE

IT8720

Etron

EJ168

OPTICAL

USB_1394_ESATA

R_USB30

USB_LAN

DDR3_3

DDR3_1

PWR_FAN

SATA3_0

SATA3_1

SATA3_2

SATA3_3

SATA3_4

SATA3_5

Etron

EJ168

F_USB30

SYS_FAN2

F_USB3

COMA

F_AUDIO

TPM

F_1394

VIA

VT6308

PCIEX4_1

PCIEX8

PCIEX4_2

GSATA3_7

GSATA3_6

Marvell

88SE9172

PCIEX16_2

Marvell

88SE9172

PCIEX1

(Note)

- 8 -

GA-990FXA-UD5 Motherboard Block Diagram

AM3+/AM3 CPU

Hyper Transport Bus

AMD 990FX

1 PCI

PCI Bus

PCI CLK

(33 MHz)

CPU CLK+/- (200 MHz)

Dual BIOS

COM Port

LPC Bus

DDR3 2000(O.C.)/1866/1600/1333/1066 MHz

6 SATA 6Gb/s

PS/2 KB/Mouse

14 USB 2.0/1.1

LAN

RJ45

Dual Channel Memory

2 USB 3.0/2.0

PCI Express Bus

1 PCI Express x1

PCIe CLK

(100 MHz)

Etron

EJ168

VIA VT6308

2 IEEE 1394a

Center/Subwoofer Speaker Out

Line Out

MIC

Line In

S/PDIF Out

Side Speaker Out

Surround Speaker Out

CODEC

2 SATA 6Gb/s

Marvell

88SE9172

2 USB 3.0/2.0

Etron

EJ168

PCIe CLK

(100 MHz)

PCI Express Bus

2 PCI Express x4

PCIe CLK

(100 MHz)

1 PCI Express x162 PCI Express x8

Switch

x8 x16

1 PCI Express x16

x16

PCI Express Bus

2 SATA 6Gb/s

Marvell

88SE9172

AMD SB950

iTE

IT8720

Realtek

RTL8111E

- 9 - Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can

become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read

the user's manual and follow these procedures:

• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

• Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

• When connecting hardware components to the internal connectors on the motherboard,

make sure they are connected tightly and securely.

• When handling the motherboard, avoid touching any metal leads or connectors.

• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic com-

ponents such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,

keep your hands dry and rst touch a metal object to eliminate static electricity.

•

Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

• Before unplugging the power supply cable from the motherboard, make sure the power sup-

ply has been turned off.

• Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

• Before using the product, please verify that all cables and power connectors of your hard-

ware components are connected.

• To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

• Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

• Do not place the computer system on an uneven surface

• Do not place the computer system in a high-temperature environment.

• Turning on the computer power during the installation process can lead to damage to sys-

tem components as well as physical harm to the user.

• If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certied computer technician.

Chapter 1 Hardware Installation

Hardware Installation - 10 -

1-2 Product Specications

CPU AM3+ Socket: 

- AMD AM3+ FX processors

- AMD AM3 Phenom

™

II processors/AMD Athlon

™

II processors

(Go to GIGABYTE's website for the latest CPU support list.)

Hyper Transport

Bus

5200 MT/s 

Chipset

North Bridge: AMD 990FX 

South Bridge: AMD SB950 

Memory 4 x 1.5V DDR3 DIMM sockets supporting up to 32 GB of system memory 

* Due to Windows 32-bit operating system limitation, when more than 4 GB of physical

memory is installed, the actual memory size displayed will be less than 4 GB.

Dual channel memory architecture 

Support for DDR3 2000 (O.C.)/1866/1600/1333/1066 MHz memory modules 

* To support a DDR3 1866 MHz (and above) memory, you must install an AM3+ CPU

rst.

(Go to GIGABYTE's website for the latest supported memory speeds and memory

modules.)

Audio Realtek ALC889 codec 

High Denition Audio 

2/4/5.1/7.1-channel 

Support for Dolby 

Home Theater

Support for S/PDIF Out 

LAN 1 x Realtek RTL8111E chip (10/100/1000 Mbit) 

Expansion Slots  2 x PCI Express x16 slots, running at x16 (PCIEX16_1, PCIEX16_2)

* For optimum performance, if only one PCI Express graphics card is to be installed, be

sure to install it in the PCIEX16_1 slot; if you are installing two PCI Express graphics

cards, it is recommended that you install them in the PCIEX16_1 and PCIEX16_2

slots.

1 x PCI Express x16 slot, running at x8 (PCIEX8) 

* The PCIEX8 slot shares bandwidth with the PCIEX16_2 slot. When PCIEX8 is

populated with a PCI Express expansion card, the PCIEX16_2 slot will operate

at up to x8 mode.

2 x PCI Express x16 slots, running at x4 (PCIEX4_1, PCIEX4_2) 

1 x PCI Express x1 slot 

(All PCI Express slots conform to PCI Express 2.0 standard.)

1 x PCI slot 

Multi-Graphics

Technology

Support for 2-Way/3-Way AMD CrossFireX 

™

technology

- 11 - Hardware Installation

Storage Interface South Bridge: 

- 6 x SATA 6Gb/s connectors (SATA3_0~SATA3_5) SATA3 supporting up to

6 SATA 6Gb/s devices

- Support for RAID 0, RAID 1, RAID 5, RAID 10, and JBOD

2 x Marvell 88SE9172 chips: 

- 2 x SATA 6Gb/s connectors (GSATA3_6, GSATA3_7) supporting up to 2

SATA 6Gb/s devices

- 2 x eSATA 6Gb/s connectors on the back panel supporting up to 2 SATA

6Gb/s devices

- Support for RAID 0 and RAID 1

USB South Bridge: 

- Up to 14 USB 2.0/1.1 ports (8 ports on the back panel, 6 ports available

through the internal USB headers)

2 x Etron EJ168 chips: 

- Up to 4 USB 3.0/2.0 ports (2 ports on the back panel, 2 ports available

through the internal USB headers)

IEEE 1394 VIA VT6308 chip: 

- Up to 2 IEEE 1394a ports (1 port on the back panel, 1 port available through

the internal IEEE 1394a header)

Internal

Connectors

1 x 24-pin ATX main power connector 

1 x 8-pin ATX 12V power connector 

8 x SATA 6Gb/s connectors 

1 x CPU fan header 

2 x system fan headers 

1 x power fan header 

1 x front panel header 

1 x front panel audio header 

1 x S/PDIF Out header 

3 x USB 2.0/1.1 headers 

1 x USB 3.0/2.0 header 

1 x IEEE 1394a header 

1 x serial port header 

1 x clearing CMOS jumper 

1 x Trusted Platform Module (TPM) header 

Back Panel

Connectors

1 x PS/2 keyboard/mouse port 

1 x optical S/PDIF Out connector 

1 x IEEE 1394 port 

8 x USB 2.0/1.1 ports 

2 x USB 3.0/2.0 ports 

2 x eSATA 6Gb/s connectors 

1 x RJ-45 port 

6 x audio jacks (Center/Subwoofer Speaker Out/Rear Speaker Out/Side Speaker 

Out/Line In/Line Out/Microphone)

I/O Controller iTE IT8720 chip 

Hardware Installation - 12 -

Hardware

Monitor

System voltage detection 

CPU/System temperature detection 

CPU/System/Power fan speed detection 

CPU overheating warning 

CPU/System/Power fan fail warning 

CPU/System fan speed control 

* Whether the CPU/system fan speed control function is supported will depend on

the CPU/system cooler you install.

BIOS 2 x 32 Mbit ash 

Use of licensed AWARD BIOS 

Support for DualBIOS 

™

PnP 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.0b 

Unique Features Support for @BIOS 

Support for Q-Flash 

Support for Xpress BIOS Rescue 

Support for Download Center 

Support for Xpress Install 

Support for Xpress Recovery2 

Support for EasyTune 

* Available functions in EasyTune may differ by motherboard model.

Support for Easy Energy Saver 

Support for Smart Recovery 

Support for Auto Green 

Support for ON/OFF Charge 

Support for Cloud OC 

Support for 3TB+ Unlock 

Support for Q-Share 

Bundled

Software

Norton Internet Security (OEM version) 

Operating

System

Support for Microsoft 

Windows 7/Vista/XP

Form Factor ATX Form Factor; 30.5cm x 24.4cm 

* GIG ABYTE reser ves the right to make any changes to the product specications and product-related informat ion

without prior notice.

- 13 - Hardware Installation

1-3 Installing the CPU and CPU Cooler

1-3-1 Installing the CPU

A. Locate the pin one (denoted by a small triangle) of the CPU socket and the CPU.

Read the following guidelines before you begin to install the CPU:

• Make sure that the motherboard supports the CPU.

(Go to GIGABYTE's website for the latest CPU support list.)

• Always turn off the computer and unplug the power cord from the power outlet before installing

the CPU to prevent hardware damage.

• Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may

locate the notches on both sides of the CPU and alignment keys on the CPU socket.)

• Apply an even and thin layer of thermal grease on the surface of the CPU.

• Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and dam-

age of the CPU may occur.

• Set the CPU host frequency in accordance with the CPU specications. It is not recommended

that the system bus frequency be set beyond hardware specications since it does not meet the

standard requirements for the peripherals. If you wish to set the frequency beyond the standard

specications, please do so according to your hardware specications including the CPU, graph-

ics card, memory, hard drive, etc.

AM3+/AM3 CPU

A Small Triangle Marking

Denotes CPU Pin One

AM3+ Socket

A Smal l Triangle Mark

Denotes Pin One of the

Socket

Hardware Installation - 14 -

B. Follow the steps below to correctly install the CPU into the motherboard CPU socket.

• Before installing the CPU, make sure to turn off the computer and unplug the power cord from the

power outlet to prevent damage to the CPU.

• Do not force the CPU into the CPU socket. The CPU cannot t in if oriented incorrectly. Adjust the

CPU orientation if this occurs.

Step 1:

Completely lift up the CPU socket locking lever.

Step 2:

Align the CPU pin one (small triangle marking) with the triangle mark

on the CPU socket and gently insert the CPU into the socket. Make

sure that the CPU pins t perfectly into their holes. Once the CPU is

positioned into its socket, place one nger down on the middle of the

CPU, lowering the locking lever and latching it into the fully locked

position.

CPU Socket

Locking Lever

- 15 - Hardware Installation

Use extreme care when removing the CPU cooler because the thermal grease/tape between the

CPU cooler and CPU may adhere to the CPU. Inadequately removing the CPU cooler may damage

the CPU.

1-3-2 Installing the CPU Cooler

Follow the steps below to correctly install the CPU cooler on the CPU. (The following procedure uses the

GIGABYTE cooler as the example.)

Step 1:

Apply an even and thin layer of thermal grease

on the surface of the installed CPU.

Step 2:

Place the CPU cooler on the CPU.

Step 3:

Hook the CPU cooler clip to the mounting lug

on one side of the retention frame. On the other

side,push straight down on the the CPU cooler

clip to hook it to the mounting lug on the reten-

tion frame.

Step 4:

Turn the cam handle from the left side to the

right side (as the picture above shows) to lock

into place. (Refer to your CPU cooler installation

manual for instructions on installing the cooler.)

Step 5:

Finally, attach the power connector of the CPU cooler to the CPU

fan header (CPU_FAN) on the motherboard.

Hardware Installation - 16 -

1-4 Installing the Memory

Read the following guidelines before you begin to install the memory:

• Make sure that the motherboard supports the memory. It is recommended that memory of the

same capacity, brand, speed, and chips be used.

(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

• Always turn off the computer and unplug the power cord from the power outlet before installing

the memory to prevent hardware damage.

• Memory modules have a foolproof design. A memory module can be installed in only one direc-

tion. If you are unable to insert the memory, switch the direction.

1-4-1 Dual Channel Memory Conguration

This motherboard provides four DDR3 memory sockets and supports Dual Channel Technology. After the

memory is installed, the BIOS will automatically detect the specications and capacity of the memory. En-

abling Dual Channel memory mode will double the original memory bandwidth.

The four DDR3 memory sockets are divided into two channels and each channel has two memory sockets as

following:

Channel 0: DDR3_2, DDR3_4

Channel 1: DDR3_1, DDR3_3

DDR3_4

DDR3_2

DDR3_3

DDR3_1

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.

1. Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.

2. When enabling Dual Channel mode with two or four memory modules, it is recommended that

memory of the same capacity, brand, speed, and chips be used for optimum performance. For op-

timum performance, when enabling Dual Channel mode with two memory modules, we recommend

that you install them in the DDR3_1 and DDR3_2 sockets.

Dual Channel Memory Congurations Table

(SS=Single-Sided, DS=Double-Sided, "- -"=No Memory)

DDR3_4 DDR3_2 DDR3_3 DDR3_1

Two Modules - - DS/SS - - DS/SS

DS/SS - - DS/SS - -

Four Modules DS/SS DS/SS DS/SS DS/SS

- 17 - Hardware Installation

1-4-2 Installing a Memory

Notch

Before installing a memory module, make sure to turn off the computer and unplug the power

cord from the power outlet to prevent damage to the memory module.

DDR3 and DDR2 DIMMs are not compatible to each other or DDR DIMMs. Be sure to install

DDR3 DIMMs on this motherboard.

DDR3 DIMM

A DDR3 memory module has a notch, so it can only t in one direction. Follow the steps below to correctly

install your memory modules in the memory sockets.

Step 1:

Note the orientation of the memory module. Spread the retaining

clips at both ends of the memory socket. Place the memory module

on the socket. As indicated in the picture on the left, place your n-

gers on the top edge of the memory, push down on the memory and

insert it vertically into the memory socket.

Step 2:

The clips at both ends of the socket will snap into place when the

memory module is securely inserted.

Hardware Installation - 18 -

1-5 Installing an Expansion Card

Read the following guidelines before you begin to install an expansion card:

• Make sure the motherboard supports the expansion card. Carefully read the manual that came

with your expansion card.

• Always turn off the computer and unplug the power cord from the power outlet before installing

an expansion card to prevent hardware damage.

Follow the steps below to correctly install your expansion card in the expansion slot.

1. Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel.

2. Align the card with the slot, and press down on the card until it is fully seated in the slot.

3. Make sure the metal contacts on the card are completely inserted into the slot.

4. Secure the card’s metal bracket to the chassis back panel with a screw.

5. After installing all expansion cards, replace the chassis cover(s).

6. Turn on your computer. If necessary, go to BIOS Setup to make any required BIOS changes for your

expansion card(s).

7. Install the driver provided with the expansion card in your operating system.

Example: Installing and Removing a PCI Express Graphics Card:

PCI Slot

PCI Express x1 Slot

PCI Express x16 Slot (PCIEX16_1/PCIEX16_2)

PCI Express x16 Slot (PCIEX8/PCIEX4_1/PCIEX4_2)

• Installing a Graphics Card:

Gently push down on the top edge of the card until

it is fully inserted into the PCI Express slot. Make

sure the card is securely seated in the slot and

does not rock.

• Removing the Card

from the PCIEX16_1/

PCIEX16_2 Slot:

Gently push back on the

lever on the slot and then

lift the card straight out

from the slot.

•

Removing the Card from

the PCIEX8/PCIEX4_1/

PCIEX4_2 Slot:

Press the latch at the end

of the PCI Express slot

to release the card and

then pull the card straight

up from the slot.

- 19 - Hardware Installation

PCIEX16_1 PCIEX16_2 PCIEX8 PCIEX4_1 PCIEX4_2

- - - - - -

- - - -

2-Way

3-Way

1-6 Setup of AMD CrossFireX

™

Conguration

A. System Requirements

- The 2-Way CrossFireX technology currently support Windows 7, Vista, XP operating systems

- The 3-Way CrossFireX technology currently support Windows 7 and Vista operating systems

- A CrossFireX-supported motherboard with two/three/four PCI Express x16 slots and correct driver

- Two/three CrossFireX-ready graphics cards of identical brand and chip and correct driver

( Current GPUs that support 3-Way CrossFireX technology include the ATI Radeon HD 3800, HD 4800,

and HD 5800 series and AMD Radeon HD 6950, HD 6970 and HD 6990 series.)

- CrossFireX bridge connector(s)

(Note)

- A power supply with sufcient power is recommended (refer to the manual of your graphics cards for the

power requirement)

B. Connecting the Graphics Cards

Step 1:

Observe the steps in "1-5 Installing an Expansion Card" and install two/three graphics cards on the PCI Ex-

press x16 slots. The following table shows the recommended congurations with two/three cards.

Step 2:

Insert the CrossFireX

bridge connector(s)

(Note)

in the CrossFireX gold edge connectors on top of the graphics

cards.

Step 3:

Plug the display cable into the graphics card on the PCIEX16_1 slot.

Recommended 2/3-Way CrossFireX Congurations:

C. Conguring the Graphics Card Driver

After installing the graphics card driver in the operating system, go to the

Catalyst Control Center. Browse to Performance\AMD CrossFireX Con-

gurations and ensure the Enable CrossFireX

™

check box is selected. Se-

lect the GPU combination you want to use. (Available combination options are

dependent on the number of graphics cards you install.)

(Note) The bridge connector(s) may be needed or not depending on your graphics cards.

Procedure and driver screen for enabling CrossFireX technology may differ by graphics cards and driver version. Refer to the

manual that came with your graphics cards for more information about enabling CrossFireX technology.

Hardware Installation - 20 -

1-7 Back Panel Connectors

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specication. Use this port for USB devices such as a USB key-

board/mouse, USB printer, USB ash drive and etc.

PS/2 Keyboard/Mouse Port

Use this port to connect a PS/2 mouse or keyboard.

Optical S/PDIF Out Connector

This connector provides digital audio out to an external audio system that supports digital optical audio.

Before using this feature, ensure that your audio system provides an optical digital audio in connector.

IEEE 1394a Port

The IEEE 1394 port supports the IEEE 1394a specication, featuring high speed, high bandwidth and

hotplug capabilities. Use this port for an IEEE 1394a device.

eSATA 6Gb/s Port

The eSATA 6Gb/s port conforms to SATA 6Gb/s standard and is compatible with SATA 3Gb/s and

SATA 1.5Gb/s standard. Use the port to connect an external SATA device or a SATA port multiplier. The

Marvell 88SE9172 chip supports RAID function. Refer to Chapter 5, "Conguring SATA Hard Drive(s),"

for instructions on conguring a RAID array.

USB 3.0/2.0 Port

The USB 3.0 port supports the USB 3.0 specication and is compatible to the USB 2.0/1.1 specication.

Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB ash drive and etc.

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following

escribes the states of the LAN port LEDs.

Activity LED

Connection/

Speed LED

LAN Port

Activity LED:Connection/Speed LED:

State Description

Orange 1 Gb ps data rate

Green 100 Mbps dat a rate

Off 10 Mbps data rate

State Description

Blinking Dat a transmissi on or receivin g is occurring

Off No data tr ansmission o r receiving is oc curring

- 21 - Hardware Installation

In addition to the default speakers settings, the ~ audio jacks can be recongured to perform

different functions via the audio software. Only microphones still MUST be connected to the

default Mic in jack ( ). Refer to the instructions on setting up a 2/4/5.1/7.1-channel audio con-

guration in Chapter 5, "Conguring 2/4/5.1/7.1-Channel Audio."

Center/Subwoofer Speaker Out Jack (Orange)

Use this audio jack to connect center/subwoofer speakers in a 5.1/7.1-channel audio conguration.

Rear Speaker Out Jack (Black)

Use this audio jack to connect rear speakers in a 7.1-channel audio conguration.

Side Speaker Out Jack (Gray)

Use this audio jack to connect side speakers in a 4/5.1/7.1-channel audio conguration.

Line In Jack (Blue)

The default line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out Jack (Green)

The default line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be

used to connect front speakers in a 4/5.1/7.1-channel audio conguration.

Mic In Jack (Pink)

The default Mic in jack. Microphones must be connected to this jack.

When removing the cable connected to a back panel connector, rst remove the cable from your •

device and then remove it from the motherboard.

When removing the cable, pull it straight out from the connector. Do not rock it side to side to •

prevent an electrical short inside the cable connector.

Hardware Installation - 22 -

1-8 Internal Connectors

Read the following guidelines before connecting external devices:

• First make sure your devices are compliant with the connectors you wish to connect.

• Before installing the devices, be sure to turn off the devices and your computer. Unplug the

power cord from the power outlet to prevent damage to the devices.

• After installing the device and before turning on the computer, make sure the device cable has

been securely attached to the connector on the motherboard.

1 3

4 12 13

1) ATX_12V

2) ATX

3) CPU_FAN

4) SYS_FAN1/2

5) PWR_FAN

6) BAT

7) SATA3_0/1/2/3/4/5

8) GSATA3_6/7

9) F_PANEL

10) F_AUDIO

11) SPDIF_O

12) F_USB1/F_USB2/F_USB3

13) F_USB30

14) F_1394

15) COMA

16) TPM

17) CLR_CMOS

91614

- 23 - Hardware Installation

131

2412

ATX

1/2) ATX_12V/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the

components on the motherboard. Before connecting the power connector, rst make sure the power

supply is turned off and all devices are properly installed. The power connector possesses a foolproof

design. Connect the power supply cable to the power connector in the correct orientation. The 12V

power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the

computer will not start.

To meet expansion requirements, it is recommended that a power supply that can withstand

high power consumption be used (500W or greater). If a power supply is used that does not

provide the required power, the result can lead to an unstable or unbootable system.

ATX_12V:

ATX:

Pin No. Denition Pin No. Denition

1 3.3V 13 3.3V

2 3.3V 14 -12V

3 GND 15 GND

4 +5V 16 PS_ON (soft On/Off)

5 GND 17 GND

6 +5V 18 GND

7 GND 19 GND

8 Power Good 20 -5V

9 5VSB (stand by +5V) 21 +5V

10 +12V 22 +5V

11 +12V (Only for 2x12-pin ATX) 23 +5V (Only for 2x12-pin ATX)

12 3.3V (Only for 2x12-pin ATX) 24 GND (Only for 2x12-pin ATX)

ATX_12V

Pin No. Denition

1 GND (Only for 2x4-pin 12V)

2 GND (Only for 2x4-pin 12V)

3 GND

4 GND

5 +12V (Only for 2x4-pin 12V)

6 +12V (Only for 2x4-pin 12V)

7 +12V

8 +12V

Hardware Installation - 24 -

3/4/5) CPU_FAN/SYS_FAN1/SYS_FAN2/PWR_FAN (Fan Headers)

The motherboard has a 4-pin CPU fan header (CPU_FAN), a 4-pin (SYS_FAN1) and a 3-pin (SYS_FAN2)

system fan headers, and a 3-pin power fan header (PWR_FAN). Most fan headers possess a foolproof

insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black

connector wire is the ground wire). The motherboard supports CPU fan speed control, which requires the

use of a CPU fan with fan speed control design. For optimum heat dissipation, it is recommended that a

system fan be installed inside the chassis.

• Be sure to connect fan cables to the fan headers to prevent your CPU and system from over-

heating. Overheating may result in damage to the CPU or the system may hang.

• These fan headers are not conguration jumper blocks. Do not place a jumper cap on the

headers.

CPU_FAN

SYS_FAN1

SYS_FAN2

PWR_FAN

CPU_FAN:

SYS_FAN1:

SYS_FAN2/PWR_FAN:

Pin No. Denition

1 GND

2 +12V /Speed Control

3 Sense

4 Speed Control

Pin No. Denition

1 GND

2 +12V /Speed Control

3 Sense

4 Reserve

Pin No. Denition

1 GND

2 +12V

3 Sense

6) BAT (Battery)

The battery provides power to keep the values (such as BIOS congurations, date, and time information)

in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a

low level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery:

Turn off your computer and unplug the power cord.1.

Gently remove the battery from the battery holder and wait for one minute. 2.

(Or use a metal object like a screwdriver to touch the positive and negative

terminals of the battery holder, making them short for 5 seconds.)

Replace the battery. 3.

Plug in the power cord and restart your computer.4.

Always turn off your computer and unplug the power cord before replacing the battery. •

Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with •

an incorrect model.

Contact the place of purchase or local dealer if you are not able to replace the battery by your- •

self or uncertain about the battery model.

When installing the battery, note the orientation of the positive side (+) and the negative side (-) •

of the battery (the positive side should face up).

Used batteries must be handled in accordance with local environmental regulations. •

- 25 - Hardware Installation

7) SATA3_0/1/2/3/4/5 (SATA 6Gb/s Connectors, Controlled by AMD SB950 South Bridge)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA

1.5Gb/s standards. Each SATA connector supports a single SATA device. The AMD SB950 South Bridge

supports RAID 0, RAID 1, RAID 5, RAID 10, and JBOD. Refer to Chapter 5, "Conguring SATA Hard

Drive(s)," for instructions on conguring a RAID array.

• A RAID 0 or RAID 1 conguration requires at least two hard drives. If more than two hard

drives are to be used, the total number of hard drives must be an even number.

• A RAID 5 conguration requires at least three hard drives. (The total number of hard drives

does not have to be an even number.)

• A RAID 10 conguration requires four hard drives.

G.QBOFM

SATA3_5

SATA3_3

SATA3_1

SATA3_4

SATA3_2

SATA3_0

Pin No. Denition

1 GND

2 TXP

3 TXN

4 GND

5 RXN

6 RXP

7 GND

8) GSATA3_6/7 (SATA 6Gb/s Connectors, Controlled by Marvell 88SE9172 Chip)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA

1.5Gb/s standard. Each SATA connector supports a single SATA device. The Marvell 88SE9172 chip

supports RAID 0 and RAID 1. Refer to Chapter 5, "Conguring SATA Hard Drive(s)," for instructions on

conguring a RAID array.

Please connect the L-shaped end of

th e SATA cable t o your SATA hard

drive.

Pin No. Denition

1 GND

2 TXP

3 TXN

4 GND

5 RXN

6 RXP

7 GND

G.QBOFM

GSATA3_6

GSATA3_7

Hardware Installation - 26 -

9) F_PANEL (Front Panel Header)

Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status

indicator on the chassis to this header according to the pin assignments below. Note the positive and

negative pins before connecting the cables.

• PW (Power Switch, Red):

Connects to the power switch on the chassis front panel. You may congure the way to turn off your

system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management Setup," for

more information).

• SPEAK (Speaker, Orange):

Connects to the speaker on the chassis front panel. The system reports system startup status by is-

suing a beep code. One single short beep will be heard if no problem is detected at system startup. If

a problem is detected, the BIOS may issue beeps in different patterns to indicate the problem. Refer

to Chapter 5, "Troubleshooting," for information about beep codes.

• HD (Hard Drive Activity LED, Blue)

Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive

is reading or writing data.

• RES (Reset Switch, Green):

Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer

if the computer freezes and fails to perform a normal restart.

• CI (Chassis Intrusion Header, Gray):

Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover

has been removed. This function requires a chassis with a chassis intrusion switch/sensor.

• MSG/PWR (Message/Power/Sleep LED, Yellow/Purple):

Connects to the power status indicator on the chassis front panel. The LED

is on when the system is operating. The LED keeps blinking when the sys-

tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep

state or powered off (S5).

The front panel design may differ by chassis. A front panel module mainly consists of power

switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your

chassis front panel module to this header, make sure the wire assignments and the pin assign-

ments are matched correctly.

Power LED

CI-

CI+

PWR-

PWR+

MSG-

PW-

SPEAK+

SPEAK-

MSG+

PW+

Message/Power/

Sleep LED

Speaker

Power

Switch

HD-

RES+

HD+

RES-

Hard Drive

Activity LED

Reset

Switch

Chassis Intrusion

Header

System Status LED

S0 On

S1 Blinking

S3/S4/S5 Off

- 27 - Hardware Installation

10) F_AUDIO (Front Panel Audio Header)

The front panel audio header supports Intel High Denition audio (HD) and AC'97 audio. You may connect

your chassis front panel audio module to this header. Make sure the wire assignments of the module con-

nector match the pin assignments of the motherboard header. Incorrect connection between the module

connector and the motherboard header will make the device unable to work or even damage it.

• The front panel audio header supports HD audio by default. If your chassis provides an AC'97

front panel audio module, refer to the instructions on how to activate AC'97 functionality via

the audio software in Chapter 5, "Conguring 2/4/5.1/7.1-Channel Audio."

• Audio signals will be present on both of the front and back panel audio connections simultane-

ously. If you want to mute the back panel audio (only supported when using an HD front panel

audio module), refer to Chapter 5, "Conguring 2/4/5.1/7.1-Channel Audio."

• Some chassis provide a front panel audio module that has separated connectors on each wire

instead of a single plug. For information about connecting the front panel audio module that

has different wire assignments, please contact the chassis manufacturer.

For HD Front Panel Audio: For AC'97 Front Panel Audio:

Pin No. Denition

1 MIC2_L

2 GND

3 MIC2_R

4 -ACZ_DET

5 LINE2_R

6 GND

7 FAUDIO_JD

8 No Pin

9 LINE2_L

10 GND

Pin No. Denition

1 MIC

2 GND

3 MIC Power

4 NC

5 Line Out (R)

6 NC

7 NC

8 No Pin

9 Line Out (L)

10 NC

11) SPDIF_O (S/PDIF Out Header)

This header supports digital S/PDIF Out and connects a S/PDIF digital audio cable (provided by expan-

sion cards) for digital audio output from your motherboard to certain expansion cards like graphics cards

and sound cards. For example, some graphics cards may require you to use a S/PDIF digital audio cable

for digital audio output from your motherboard to your graphics card if you wish to connect an HDMI

display to the graphics card and have digital audio output from the HDMI display at the same time. For

information about connecting the S/PDIF digital audio cable, carefully read the manual for your expan-

sion card.

Pin No. Denition

1 SPDIFO

2 GND

F_PANEL(NH) F_PANEL

(H61M-D2)

9 1

10 2

Hardware Installation - 28 -

12) F_USB1/F_USB2/F_USB3 (USB 2.0/1.1 Headers)

The headers conform to USB 2.0/1.1 specication. Each USB header can provide two USB ports via an

optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

G.QBOFM

Pin No. Denition

1 Power (5V)

2 Power (5V)

3 USB DX-

4 USB DY-

5 USB DX+

6 USB DY+

7 GND

8 GND

9 No Pin

10 NC

Do not plug the IEEE 1394 bracket (2x5-pin) cable into the USB 2.0/1.1 header. •

Prior to installing the USB bracket, be sure to turn off your computer and unplug the power •

cord from the power outlet to prevent damage to the USB bracket.

When the system is in S4/S5 mode, only the USB ports routed to the F_USB1 header can sup-

port the ON/OFF Charge function.

13) F_USB30 (USB 3.0/2.0 Header)

The header conforms to USB 3.0/2.0 specication and can provide two USB ports. For purchasing the

optional 3.5" front panel that provides two USB 3.0/2.0 ports, please contact the local dealer.

Pin No. Denition Pin No. Denition

1 VBUS 11 D2+

2 SSRX1- 12 D2-

3 SSRX1+ 13 GND

4 GND 14 SSTX2+

5 SSTX1- 15 SSTX2-

6 SSTX1+ 16 GND

7 GND 17 SSRX2+

8 D1- 18 SSRX2-

9 D1+ 19 VBUS

10 NC 20 No Pin

F_AUDIO(H)

F_PANEL(NH) F_PANEL

(H61M-D2)

- 29 - Hardware Installation

14) F_1394 (IEEE 1394a Header)

The header conforms to IEEE 1394a specication. The IEEE 1394a header can provide one IEEE 1394a

port via an optional IEEE 1394a bracket. For purchasing the optional IEEE 1394a bracket, please con-

tact the local dealer.

• Do not plug the USB bracket cable into the IEEE 1394a header.

• Prior to installing the IEEE 1394a bracket, be sure to turn off your computer and unplug the

power cord from the power outlet to prevent damage to the IEEE 1394a bracket.

• To connect an IEEE 1394a device, attach one end of the device cable to your computer and

then attach the other end of the cable to the IEEE 1394a device. Ensure that the cable is se-

curely connected.

G.QBOFM

Pin No. Denition

1 TPA+

2 TPA-

3 GND-

4 GND

5 TPB+

6 TPB-

7 Power (12V)

8 Power (12V)

9 No Pin

10 GND

15) COMA (Serial Port Header)

The COM header can provide one serial port via an optional COM port cable. For purchasing the op-

tional COM port cable, please contact the local dealer.

Pin No. Denition

1 NDCD-

2 NSIN

3 NSOUT

4 NDTR-

5 GND

6 NDSR-

7 NRTS-

8 NCTS-

9 NRI-

10 No Pin

Hardware Installation - 30 -

16) TPM (Trusted Platform Module Header)

You may connect a TPM (Trusted Platform Module) to this header.

F_AUDIO(H)

DB_PORT

F_PANEL(NH) F_PANEL

(H61M-D2)

Voltage measurement module(X58A-OC)

DIP

1 2 3

BIOS Switcher (X58A-OC)

PWM Switch (X58A-OC)

M_SATA

Pin No. Denition Pin No. Denition

1 LCLK 11 LAD0

2 GND 12 GND

3 LFRAME 13 NC

4 No Pin 14 ID

5 LRESET 15 SB3V

6 NC 16 SERIRQ

7 LAD3 17 GND

8 LAD2 18 NC

9 VCC3 19 NC

10 LAD1 20 SUSCLK

17) CLR_CMOS (Clearing CMOS Jumper)

Use this jumper to clear the CMOS values (e.g. date information and BIOS congurations) and reset

the CMOS values to factory defaults. To clear the CMOS values, place a jumper cap on the two pins to

temporarily short the two pins or use a metal object like a screwdriver to touch the two pins for a few

seconds.

Always turn off your computer and unplug the power cord from the power outlet before clear- •

ing the CMOS values.

After clearing the CMOS values and before turning on your computer, be sure to remove the •

jumper cap from the jumper. Failure to do so may cause damage to the motherboard.

After system restart, go to BIOS Setup to load factory defaults (select Load Optimized De- •

faults) or manually congure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS

congurations).

Open: Normal

Short: Clear CMOS Values

+ 78 hidden pages