GE GFSS2KEYCSS, GFSS2KEYASS, GFSS2HCYCSS, GFSS2HCYASS, GFSL2KEYHLS Owner’s Manual

...

0 (0)

GEAppliances.com

Safety Instructions ........... 2,3

Operating Instructions

Automatic Icemaker ............... 11

Care and Cleaning ............. 12, 13

Controls ............................ 4

Crispers and Pans ................... 8

Freezer .......................... 9, 10

Replacing the Light Bulbs .......... 14

Shelves and Bins .................... 7

Water Filter ....................... 5, 6

Installation Instructions

Installing the Refrigerator ....... 16-20

Installing the Water Line ........ 30-32 Preparing to Install

the Refrigerator .................... 15

Removing and Replacing

the Doors (Double Door

Refrigerator Models onlg) ....... 27-29 Removing and Replacing the

Freezer Drawer ................. 21, 22 Reversing the Door Swing (Single Door Refrigerator

Models only) ................... 23-26

Models 20, 22 and 23

Cong61ateur inf6rieur

R frig rateurs

La section ffan_aise commence 6 la page 45

Congelador inferior

Refrigeradores

4.--

Troubleshooting Tips ...... 33-36

Normal Operating Sounds .......... 33

Consumer Support

Consumer Support ........ Back Cover

Performance Data Sheet ....... 41, 42 Owner's Registration

for Canadian Customers ........ 37, 38

State of California Water

Treatment Device Certificate .... 43, 44 Warrantg for Canadian

Customers ......................... 40

Warrantg for U.S. Customers ....... 39

Write the model and serial numbers here:

Model #

Serial #

La secci6n en espa_ol empieza en la p6gina 85

Find these numbers on a label on the right side, near the top of the

refrigerator compartment.

200D9366PO015 49-60604 04-09JR

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

tL WARNING!

Use this appliance only for its intended purpose as described in this Owner's Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

_,This refrigerator must be properly installed

and located in accordance with the Installation Instructions before it is used.

Donot allow children to climb,stand or hang on the shelvesinthe refrigerator.They could

damage the refrigerator and seriously injure

themselves.

Donot touch the cold surfaces in the freezer compartment when hands are damp or wet.

Skinmay stick to these extremely cold surfaces. Donot store or usegasolineor other flammable

vapors and liquidsinthe vicinity of this or any

other appliance. Keepfingers out of the "pinch point" areas;

clearancesbetween the doorsand between

the doors and cabinet are necessarilgsmall.

Becareful closing doors when children are inthe area.

_, Inrefrigerators with automatic icemakers,

avoidcontact with the moving parts of the ejector mechanism, or with the heating element

that releasesthe cubes. Do not place fingers or

handson the automatic icemaking mechanism

while the refrigerator is plugged in.

Unplugthe refrigerator before cleaning and making repairs.

NOTE:Westronglg recommend that ang servicing beperformed bg a qualifiedindividua!.

Settingeither or both controlsto the Offposition doesnot remove power to the light circuit.

Donot refreezefrozen foods which have

thawed completelg.

DANGER! RISK OF CHILD ENTRAPMENT

PROPERDISPOSAL OF THE REFRIGERATOR

Childentrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still

dangerous...evenif theg will sit for "just a few dags." If gou are getting rid of gour old refrigerator, please

follow the instructions below to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

Takeoff the doors.

Leavethe shelves in place sothat children mag not

easilgclimb inside.

Refrigerants

All refrigeration products contain refrigerants, which under federal law must be removed prior

to product disposal. If gou are getting rid of an old refrigeration product, check with the compang

handling the disposal about what to do.

USEOF EXTENSION CORDS

Because of potential safetg hazards under certain conditions, we stronglg recommend against the use of an extension cord.

However,if gou must use an extension cord, it isabsolutelg necessargthat it be a UL-listed (inthe UnitedStates) or a CSAcertified (inCanada),S-wiregrounding tgpe appliance extension cord having a grounding tgpe plug

and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120volts.

GEAppliances.com

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

Thepower cord of this appliance is equipped with a 3-prong (grounding)plug which mates

with a standard 3-prong (grounding)wall outlet to minimize the possibility of electricshock hazard from

this appliance. Have the wall outlet and circuit checked bg a

qualified electrician to make surethe outlet is properlg grounded.

Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to

have it replaced with a properly grounded 3-prong wall outlet.

Therefrigerator should alwags be plugged into its own individual electrical outlet which hasa voltage

rating that matches the rating plate.

USE OF ADAPTER PLUGS

Adapter plugs are not permitted in Canada.

Thisprovides the best performance and alsoprevents overloading house wiring circuits which could cause a

fire hazardfrom overheated wires. Never unplug gour refrigerator bg pulling on the

power cord.Alwags grip plug firmlg and pull straight out from the outlet.

Repairor replace immediatelg all power cords that have become fraged or otherwise damaged. Do not

usea cord that shows cracks or abrasion damage along its length or at either end.

When moving the refrigerator awag from the wall, be careful not to roll overor damage the

power cord.

READAND FOLLOWTHISSAFETYINFORMATIONCAREFULLY. SAVETHESEINSTRUCTIONS

About the controlswith temperature settings.

_ Adjust F...... _Co'de_ Q _irm_ _C0,derj_ Q _irmer_ Adjust Refdgerotor )

o_soff o_soff

9 is Coidest 9 is Coldest

(onsome models)

i ® o,o,, ®

L 9 is ColdestAdjust Freezer Adjust Refrigerator

Temperature Temperature

(on some models)

9is Coldest

9FsColdest

01sOft

0isoff

(on some models)

NOTE: The refrigerator is shipped with protective film covering the digital temperature controls. If this film was not removed during installation, remove it now.

Initially, set the refrigerator control at 5 and the freezer control at 5. Allow 24 hours for the temperature to stabilize. Several adjustments mabt be required. Adjust the controls one increment at a time, and allow 24 hours after each adjustment for the refrigerator to reach the temperature blou have set.

Setting either or both controls to 0 for digital and 0 for the refrigerator control knob stops cooling in both the refrigerator and freezer compartments, but does not shut off electrical power to the refrigerator.

About the water filter. Ion20 modelsonly) GEAppliances.com

Water Filter Cartridge

Thewater filter cartridge islocated in the

back upper right corner of the refrigerator compartment.

When to Replace the Filter

Thefilter cartridge should be replaced when the flow of water to the icemaker

decreases,or everg romonths.

Installing the Filter Cartridge

0 If gou are replacingthe cartridge,first

remove the old one.Open the cartridge cover bg pressing in on the tab at the

front and pulling down.

Removethe cartridge bg slowlg rotating

it counterclockwise. A small amount of water mag drip down.

CAUTION:Ifairhasbeen

trapped in the system,the filter cartridge may be ejectedasit is removed.Usecautionwhen

removing.

Removethe protective foil from the end

of the cartridge.

Liningup the arrow on the cartridge

and the cartridge holder,slowlg rotate the cartridge clockwise until itstops.

When the cartridge isproperlg installed, gou will feel it "click" as it locks into place.

Thegrip on the end of the cartridge should be positionedverticallg.

Do not overtighten.

Filter Bypass Plug

Youmust usethe filter bgpass plug when a replacement filter cartridge is not available.

The icemaker will not operate without the

filter or filter bgpass plug.

Replacement Filters: To order additional filter cartridges

in the United States, visit our Website, GEAppliances.com, or call GE Parts and

Accessories, 800.626.2002.

Filter Model GSWF

Customersin Canadashould consult the gellow pages for the nearest Habe

ServiceCenter.

Closethe cartridge cover.

About the water filter. (on22 and 23 models only)

Water Filter Cartridge

Thewater filter cartridge islocated in the

back upper right corner of the refrigerator compartment.

When to Replace the Filter

Thefilter cartridge should be replacedwhen the flow of water to the icemaker decreases

or every 6 months.

Installing the Filter Cartridge

0 If you are replacing the cartridge,first

remove the old one by slowly turning it to the left. DONOTpull down on the

cartridge. A small amount of water may drip down.

CAUTION:Ifairhasbeen

trapped in the system,the filter cartridge may be ejectedasit is removed.Usecautionwhen

removing.

Removethe protective foil from the end

0 of the cartridge.

Fillthe replacement cartridge with water from the tap to allow for better flow from the icemaker.

Filter Bypass Plug

Youmust usethe filter bypass plug when a replacement filter cartridge is not available.

The icemaker will not operate without the

filter or filter bypass plug.

Replacement Filters: To order additional filter cartridges

in the United States, visit our Website, GEAppliances.com, or call GE Parts and

Accessories, 800.626.2002.

Filter iVlodel iVlWF

Customersin Canadashould consult the yellow pagesfor the nearest Mabe

ServiceCenter.

Liningup the arrow on the cartridge

and the cartridge holder,slowly rotate the cartridge clockwise until itstops.

When the cartridge isproperly installed, you will feelit "click" as it locksinto place.

Do not overtighten.

About: the shelves and bins. GEApp,ances.com

Not all features are on all models.

Rearranging the Shelves

Shelves inthe refrigerator compartment are adjustable.

Refrigerator Compartment

To remove:

0 Removeall items from the shelf.

0 Tilt the shelf up at the front.

Liftthe shelf up at the back and

Some models have wire shelves that can be adjusted in the same

manneK

bring the shelf out.

To replace:

While tilting the shelf up, insert the top

hook at the back of the shelf in a slot on the track.

Lowerthe front ofthe shelf until the bottom of the shelf locksinto place.

Non-Adjustable Shelves on the Door (onsome models)

Toremove: Lift the shelf straight up;then pull out.

Toreplace: Engagethe shelf in the molded supports on the door and pushdown.

It will lock in place.

About the crispers and pans.

Not all features are on all models.

Fruit and Vegetable Crisper

Excesswater that mag accumulate in the bottom of the drawers or under the drawers

should bewiped dru.

Adjustable Humiditg Crisper (onsome models)

Slidethe control allthe wag to the HIGHsetting to provide high humidity

recommended for most vegetables.

Snack Pan (onsomemodels)

Slidethe control all the wag to the LOW setting to provide lower humidity levels

recommended for most fruits.

This pan can be moved to the most useful

location for uour familu's needs.

Toremove, slide the pan out to the stop position,lift the pan up and pastthe stop

position and lift it out.

About the freezer drawer. (onsome models) GEAppliances.com

Not all features are on all models.

Freezer Shelves and Baskets

Appearance and features may vary

Appearance may vary

0 A shelf above the icestorage bin 0 A half-width basket

A deep full-width basket

Basket Removal To remove the deep full-width basket on

freezer drawer models:

Openthe freezer drawer until it stops.

Thefreezer basket rests on the inside

tabs on the drawer slides. Liftthe basket so that it is out of all

6 slide bracket tabs.

Tilt the basket and lift out ofthe drawer.

To remove the half-width basket:

_! Pullthe basket out to the stop location.

Liftthe basket up at the front to release it from the stop hooks on each side.

Liftthe basket out to remove it from the sides.

NOTE:Do not fill basketshigher than the rim of the basket.This mag cause basketsto stick

orjam when opening or closing.

When replacing the deep full-width basket:

Tiltthe basket back and lower it down

into the drawer.Rotatethe basketto a horizontal position and press it down into

the 6 alignment tabs. NOTE:Alwagsbe surethat the basket is

seated in all 6 slidebracket tabs before sliding back into the freezer.Thebasket can be

turned in either direction front to back and installed into the freezer.

When replacing the basket, make sure that

the basket goes under the stop hooks on

each side. NOTE:Alwagsbe sureto fullg closethis

basket.

Appearance may vary

About the freezer compartment. Ionsome models)

Not all features are on all models.

Freezer Shelf and Basket

0 A full-width fixed wire shelf 0 A full-width sliding wire basket

Basket Removal

To remove the full-width sliding wire basket

on door models:

Open the basket out to its full extension.

Lift up the front of the basket and pull straight out to remove.

Fixed Shelf Removal

NOTE:Thefull-width wire shelf isnot intended to slide.

To remove for cleaning:

Holdthe shelf at the front and pull itfirmlg forward.

NOTE:Do not fill baskethigher than the rim of the basket. This mag cause basket to stick or

jam when opening or closing.

When replacing the full-width sliding

wire basket:

Insertthe wire basket into the lower liner's

railsand push back into place.

When replacing the full-width sliding wire

shelfi

Insertthe wire shelf into the upper liner's rails

and push back into place.

To remove

To replace

Non-Adjustable Shelf on Freezer Door

Toremove: Liftthe shelfstraight up; then pull out.

Toreplace: Engagethe shelf inthe molded supports on the door and push down. Itwill

lock in place.

About the.automatic ice.maker. Ionsome models) GEAppliances.com

A newly installed refrigerator may take 12 to 2/4 hours to begin making ice.

Power Automatic Icemaker Switch

._ icemaKer

Power _rArm LIgn_

The icemaker will produce seven cubes

per cycle-approximately 100-!30 cubes in a 24-hour period, depending on freezer compartment temperature, room

temperature, number of door openings

and other use conditions. See below for how to access ice and reach

the power switch.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch in the O (off) position.

When the refrigerator has been connected to the water supply, set the power switch to the I (on) position. The icemaker power

light will turn green when the freezer light switch is pressed in or when the freezer door is closed.

The icemaker will fill with water when it

cools to 15°F (-10°C). A newly installed refrigerator may take 12 to 2/4hours to

begin making ice cubes.

Mouwill hear a buzzing sound each time the icemaker fills with water.

Throw away the first few batches of ice

to allow the water line to clear. Be sure nothing interferes with the sweep

of the feeler arm. When the bin fills to the level of the feeler

arm, the icemaker will stop producing ice. It is normal for several cubes to bejoined

together. If ice is not used frequently, old ice cubes

will become cloudy, taste stale and shrink.

NOTE:In homes with lower-than-average water pressure, _jouma_j hear the icemaker

Cblclemultiple times when making one batch of ice.

NOTE:Set the power switch to the 0 (off) position if the water supplg is shut off.

To reach the power switch.

Accessing Ice and Reaching

:ii i ii ii iiIII IIIIIII

the shelf above the ice bin straight out. Always be sure to replace the shelf.

Icemaker Accessory Kit

the Power Switch To reach the icemeker power switch, pull

Touccess ice, simply pull the bin forward.

If your refrigerator did not come already equipped with an automatic icemaker,

an icemaker accessory kit is available at extra cost.

TO access ice.

Check the back of the refrigerator for the specific icemaker kit needed for your

model.

Careand cleaning of the refrigerator.

Cleaning the Outside

Thedoor handles and trim. Clean with a cloth dampened with soapy water. Dry with

a soft cloth. Do not usewax on the door handlesand trim.

Keepthe outside clean. Wipe with a clean cloth lightly dampened with kitchen

appliance wax or mild liquid dishdetergent. Dry and polish with a clean,soft cloth.

Do not wipe the refrigerator with o soiled dish cloth or wet towe!. These may leave

a residue that can erode the paint. Do not usescouring pads, powdered cleaners, bleach or cleaners containing bleach

because these products can scratch and weaken the paint finish.

Cleaning the Inside

Tohelp prevent odors, leavean open box of baking soda in the refrigerator and freezer

compartments.

Unplug the refrigerator before cleaning.

If this is not practical, wring excessmoisture out of sponge or cloth when cleaning around

switches, lights or controls. Usean appliance wax polishon the inside

surface between the doors. Usewarm water and baking soda solution-

about a tablespoon (15ml) of baking sodato a quart (1liter)of water.This both cleansand

neutralizesodors. Rinseand wipe dry.

Thestainless steel panels and door handles. Stainlesssteel (onsome models)

can be cleanedwith a commercially available stainlesssteel cleaner.A spray-on

stainlesssteel cleaner works best.

Donot use appliance wax or polish

on the stainlesssteel.

After cleaning the door gaskets, apply a thin layer of petroleumjelly to the door gaskets

at the hinge side.This helpskeepthe gaskets from sticking and bending out of shape.

Avoid cleaning cold glass shelves with hot

water because the extreme temperature difference mag cause them to break. Handle glass shelves carefu!lg. Bumping tempered glass can cause it to shatter.

Do not wash any plastic refrigerator parts in the dishwasher.

Behind the Refrigerator

Becareful when moving the refrigerator awag from the wall. Alltgpes of floor

coveringscan be damaged, particularlg cushioned coverings and those with

embossedsurfaces. Raisethe levelinglegs located at the bottom

front of the refrigerator.

Pullthe refrigerator straight out and return it

to position bg pushing it straight in.Having

Preparing for Vacation

GEAppliances.com

the refrigerator in a sidedirection mag result in damage to the floor covering

or refrigerator. Lowerthe leveling legsuntil theg touch

the floor. When pushing the refrigerator back, make

sure gou don't rol! over the power cord or icemaker supplg line (on some models).

Forlong vacations or absences,remove

food and unplug the refrigerator. Cleanthe

interior with a baking soda solution of one

tablespoon (15ml) of baking soda to one

quart (1liter)of water. Leavethe doors open. Setthe icemaker power switch to the O (offJ

position and shut off the water supplg to

the refrigerator.

Preparing to Move

Secureall looseitems such as base grille, shelvesand drawers bg taping them

securelg in place to prevent damage.

When using a hand truck to move the

refrigerator,do not rest the front or back ofthe refrigerator against the hand truck.

This could damage the refrigerator.Handle

onlg from the sidesof the refrigerator.

If the temperature can drop below freezing, have a qualified servicerdrain the water

supplg sgstem (on some models)to prevent serious propertg damage due to flooding.

Be sure the refrigerator stags in an upright position during moving.

Replacing the light bulbs.

Turning the control to the Off position does not remove power to the light circuit.

Refrigerator Lights

Appearance mag varg

CAUTION:Lightbu/b_n_oy

be hot.

Unplugthe refrigerator.

Toremove the light shield,grasp the

shieldat the back and pull out to release

the tabs at the back.

Rotatethe shield down and then forward

to releasethe tabs at the front of the shield.

Freezer Light

Zi,CAUTION:Lightbu/b_n_oy

be hot.

Unplugthe refrigerator.

The bulb islocated at the top of the

freezer insidealight shield.Toremove the shield,grasp the shield at the back and

pull out to releasethe tabs at the back. Rotatethe shield down and then forward

to releasethe tabs at the front of the shield.

O After replacing with an appliance bulb

of the same or lower wattage, replace

the shield.

Plugthe refrigerator back in.

NOTE:Appliance bulbs mag be ordered from GEPartsand Accessories,800.626.2002.

After replacing with an appliance bulb

of the same or lower wattage, replace

the shield.

Plugthe refrigerator back in.

I tallati

structi

Questions? Call 800.GE.CARES (800.432.2737} or Visit our Website at: GEAppliances.com

In Canada, call 1.800.561.3344 or Visit our Website at: www.GEAppliances.ca

efrigerator

Models 20, 22 and 23

BEFORE YOU BEGIN

Read these instructions completelg and carefullg.

• IMPORTANT - Savetheseinstructions

for local inspector's use.

• IMPORTANT - Observeallgoverning

codes and ordinances.

• Note to Installer- Be sureto leavethese instructionswiththe Consumer,

• Note to Consumer - Keep these instructionsfor

future reference.

• Skill level -Installation of this appliance requires basic mechanical skills.

• Completion time - Refrigerator Installation

20 minutes Water Line Installation

30 minutes

Proper installation is the responsibilitg of the installer,

• Product failure due to improper installation is not covered under the Warrantg.

TOOLS YOU MAY NEED

Adjustable Wrench

1/4" Outer Diameter

Compression Nut

and Ferrule (sleeve)

(icemaker models onlg)

3/32", 1/8" and 3/16" Allen

1/8" Drill Bit and Electric or Hand Drill

Phillips Head Screwdriver

wrenches

3/8" and 5/16" Socket

Ratchet/Driver

Tope measure

PREPARATION

MOVING THE REFRIGERATOR INDOORS If the refrigerator will not fit through a doorwag,

the refrigerator door and freezer drawer can be removed.

• To remove the refrigerator door, see Step 1 in the Reversing the Door Swing section.

• To remove the freezer drawer, see the Removing the Freezer Drawer section.

WATER SUPPLYTO THE ICEMAKER AND DISPENSER (ON SOME MODELS}

If the refrigerator has an icemaker, it will have

to be connected to a cold water line. A GEwater supply kit (containing tubing, shutoff valve, fittings

and instructions) is available at extra cost from gout dealer, by visiting our Website at

GEAppliances.com (in Canada at www.GEAppliances.ca) or from Parts and

Accessories, 800.626.2002 (in Canada

1.888.661.1616).

Pencil

Wire Cutters

1/4" Nut Driver

Level

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature will go below 60% (lro°c) because it will not run often

enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature will go above 100% (37°C)because it will not perform

properly. Install it on (] floor strong enough to support it fully

loaded.

CLEARANCES

Allow the following cle(]r(]nces for ease of inst(]ll(]tion, proper air circulation and plumbing and electrical

connections.

Standard Depth

Models Sides 1/8" (3mm) Top 1" (25 mm)

Back 1" (25 mm)

REMOVETOPCAP{cont.)Ion somemodels)

REINSTALL DOORS, DRAWERS AND TOP CAP

r_ carefully lower the door(s)onto the center hinge(s).

Reinstalltop hinge(s).NOTE: Ensurethe door is properly aligned to the case top to avoid readjustment of the door during top cup

reinstc]llc]tion.

r_ Place cap over the top of the refrigerator. Reinstall

the original screws in the top and back of the cap.

[] Reinstallthe bottom freezer drawer or door. Referto

"Replacing the Freezer Drawer" section or Step 8 of "Reversing the Door Swing" section.

REMOVETOPCAPIonsomemodels)

• IMPORTANTNOTE:This refrigerator is34-1/2" deep. Doors and passagewags leading to the installation

location must be at least 36" wide in order to leave

the doors and handles attached to the refrigerator while transporting it into the installation location. If

passageways are lessthan 36", the refrigerator doors

and handles can easily be scratched and damaged. Thetop cap and doors can be removed to allow the

refrigerator to be safely moved indoors. Start with Step A.

• If it is not necessary to remove doors, skip Step A. Leave tape and all packaging on doors until the refrigerator is in the final location.

•SKID REMOVAL:Tilt refrigerator to each side to remove skid.

• NOTE:Usea padded hand truck to move this refrigerator. Place the refrigerator on the hand truck

with a side against the truck. We strongly recommend that TWO PEOPLEmove and complete this installation.

[] Locate and remove the two Phillips head screws on

the top of the refrigerator. Removethe two screws on each side (It the rear of the top cap. Lift off and

remove top cap.

rB1 Removethe fresh-food door(s).Refer to Steps i and 3

of "Reversing the Door Swing" section or Steps i and

2 of "Removing the Doors" section.

rc1 Remove the bottom freezer drawer or door. Referto

"Removing FreezerDrawer" section or Step 2 of "Reversing the Door Swing" section.

rD1 Move refrigerator to the inst(]ll(]tion location.

Top Hinge B

[] CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE

(icemaker models)

A cold water supplLIisrequired for automatic icem(]ker operation. Ifthere isnot (]cold water

supplLI,LlOUwill need to provide one. See Instolling the Woter Line section.

NOTES:

• Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged

into the wall outlet.

• If your refrigerator does not have c]water filter, we recommend installing one if your water supply has

sand or particles that could clog the screen of the refrigerator's water valve. Install it in the water line

near the refrigerator. If using GESmc]rtConnectT" Refrigerator Tubing Kit, you will need tin additional tube (WX08X10002)to connect the filter. Do not cut

plastic tube to install filter.

Installation Instructions

B3CONNECTING THE REFRIGERATOR TO

THE HOUSE WATER LINE (cont.)

j'_ If you are using copper tubing, place a

compression nut and ferrule (sleeve) onto the end of the tubing coming from the house cold water supplg.

If gou are using the GE SmartConnect'" tubing, the nuts are alreadg assembled to the tubing.

r_ if gou are using copper tubing, insert

the end of the tubing into the refrigerator connection, at the back of the refrigerator, as far as possible. While holding the tubing, tighten the fitting.

If gou are using GE SmartConnect'" tubing, insert the molded end of the tubing into the refrigerator connection, at the back of the refrigerator, and tighten the compression nut until it is hand tight. Then tighten one additional turn with a wrench. Overtightening may cause leaks.

[] Fasten the tubing into the clamp provided to

hold it in position. You may need to pry open the clamp.

One of the illustrations below will look like the connection on gour refrigerator.

Icemaker-Readg models

Tubing

Clamp

1/4"

Compression

Nut

Ferrule (sleeve)

Refrigerator

Connection

Icemaker-lnstalled Models

Refrigerator (sleeve) Compression

Connection

SmartConnecf M

Tubing

Ferrule 1/4"

1/4" Copper

Tubing

[] TURN ON THE WATER SUPPLY

(icemaker models)

Turn the water on at the shutoff valve (house water supply) and check for any leaks.

[] PLUG IN THE REFRIGERATOR

On models with an icemaker, before plugging in the refrigerator, make sure the icemaker power switch is set to the O (off) position.

See the grounding information attached to the power cord.

[_[] PUTTHEREFRIGERATORIN PLACE

Hove the refrigerator to its final location.

LEVEL THE REFRIGERATOR

Adjustable legs at the front corners of the refrigerator should be set so the refrigerator is firmlg positioned on the floor, and the front is raised just enough that the door closes easilg when opened about halfway.

To adjust the leveling legs, turn the legs

clockwise to raise the refrigerator, counterclockwise to lower it.

SmartConnect[M

Tubing

1/4" Tubing

TubingClamp

Installation Instructions

INSTALLING THE REFRIGERATOR {cont.}

_-I REMOVE THE FRESH FOOD

DOOR HANDLE

(For placement in the installation location or reversal of the handles - on some

models}

Stainless steel (on some models}:

0 REMOVING

THE DOOR

HANDLE: Loosen the set screws with the 3/32" Allen wrench

and remove the handle.

NOTE: For

Double Door

models follow the same

procedure on the opposite door.

Mounting Fasteners

(appearance mag varg)

m REMOVE THE FREEZER DOOR HANDLE

Stainless steel and plastic handles: O Loosen the set screws located on the

underside of the handle with the 1/8" Allen

wrench and remove the handle.

NOTE: If the handle mounting fasteners need

to be tightened or removed, use a 3/16" Allen wrench.

Badge

Plastic handle

(on some models):

O REMOVING THE DOOR HANDLE: Depress the

tab on the underside of the handle and slide the handle up and off of the mounting

fasteners.

REVERSING THE

DOOR HANDLE

(on some

models):

• Remove the handle

mounting

fasteners with a 3/16" Allen wrench and transfer the handle

mounting

fasteners to the right side.

Remove the logo badge.

Remove and transfer the plug button to

the left side of the fresh food door. NOTE:

Use a flat plastic edge to prevent damaging the door. Remove any adhesive on the door with a mild detergent. Remove the paper covering on the adhesive backing on the logo badge prior to carefullg attaching the badge to the door.

(appearance mag varg)

Installation Instructions

[_] ATTACH THE FRESH FOOD

DOOR HANDLE

Stainless steel handle:

@ Attach the

handle to the handle mounting

fasteners and tighten the set

screws with a 3/32" Allen

wrench.

NOTE: For Double Door models follow

the same

procedure on the opposite door.

Plastic handle: @ Attach the handle to the handle mounting

fasteners bLI aligning the slots with the

handle mounting fasteners.

@ Slide it down until it is firmly locked into

position.

Mounting

Fasteners

(appearance mau vary)

[] ATTACH THE FREEZER DOOR HANDLE

Stainless steel and plastic handles: @ Attach the handle firmly to the mounting

fasteners and tighten the set screws on the bottom of the handle with a 1/8" Allen

wrench.

(appearance mau vary)

Slots on back of U handle

(appearance mau vary)

Mounting

fasteners

Installation Instructions

INSTALLING THE REFRIGERATOR {cont.}

r_] LEVEL THE REFRIGERATOR

The leveling legs hove 2 purposes:

1) Leveling legs adjust so the refrigerator is firmlg positioned on the floor and does not

wobble.

2} Leveling legs serve as a stabilizing brake

to hold the refrigerator securely in position during operation and cleaning. The leveling

legs also prevent the refrigerator from

tipping.

r_ Remove the grille bg removing the two Phillips

head screws.

r_] SET THE CONTROLS

Set the controls to the recommended setting.

5 5

I"EOO''E"OEOOO"'"O'SETT'"osl

0 is off 0 is off

(C°lde0 0 _°rmer_ (COlder_ 0 _0rm_

9 is Coldest 9 is Coldest

® ®

r_ Turn the leveling legs clockwise to ruise

the refrigerator, counterclockwise to lower it.

CAUTION: To°voidpossible

personal injurg or propertg damage, the leveling legs must be firmlg touching

the floor.

r_ Replace the base grille bg inserting the two

Phillips head screws.

Adjust Freezer Adjust Refrigerator

Temperoture Tempereture

REMOVE PACKAGING, START ICEMAKER (icemoker models}

A) Remove all tape, foam and protective

packing from shelves and drawers.

B) Remove the tie downs from the freezer

baskets.

C} Place half width basket onto drawer slides.

See About the freezer section for instructions.

Set the icemaker power switch to the I (on} position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (-9°C) or below. It will then begin operation automaticallg. It will take 2-3 dags to fill the ice bin.

NOTE: In lower water pressure conditions, the water valve mag turn on up to 3 times to deliver enough water to the icemaker.

Installation Instructions

REMOVING THE FREEZER DRAWER (onsome models}

The freezer drawer can be removed, if needed, to fit through tight areas.

Read these instructions completelg and carefullg.

_] REMOVE THE BASKET

r_ open the freezer drawer until it stops. r_ The freezer basket rests on a frame inside the

freezer drawer. Lift the basket up at the back.

r_ Lift the front up and lift the entire basket up

and out of the drawer.

[_ REMOVE THE DRAWER FRONT

r_ Remove the screw on each side of the railing.

REMOVE THE DRAWER FRONT {cont.)

Lift up on both sides of the freezer drawer handle to separate the drawer railings from

the rail assemblies. Set the drawer front on a non-scratching

surface. Push the rail assemblies back into locking

position.

Rail Assemblg Drawer

Assemblg

[_] REMOVE THE BASE GRILLE

(if needed}

If, after removing the freezer drawer and refrigerator door, the refrigerator will still not fit through a doorwag, the base grille can be

removed.

[_ Remove the base grille bg removing the

screws.

Screw

Installation Instructions

REPLACING THE FREEZER DRAWER (onsomemodeIsI

r_ ATTACH AND SECURETHE DRAWER

Two people mag be required to complete

this procedure.

I_ ATTACH AND SECURETHE DRAWER

FRONT TO THE SLIDES

rA1 Pull out the rail assemblies to the full length

on each side of the cabinet.

FRONT TO THE SLIDES (cont.)

[] Replace the screws on both rail assemblies.

i /!

.!l

rB1 Locate the slots on the inside of the rail

assemblies near the back.

Slot

...........-... _. ! iJ

Railassembly

rc] Insert the hooks at the back of the drawer

railings into the slots on the rail assemblies.

r_ Lower the front of the drawer, making sure the

tabs on the sides of the railings fit into the front slots in the rail assemblies.

Screw

[_] REPLACE THE FREEZER BASKET

Replace the lower freezer basket by lowering it into the frame.

Installation Instructions

REVERSINGTHE DOOR SWING {Single Door Refrigerator Models onlg)

IMPORTANT NOTES

When reversing the door swing:

NOTE: Door swing is not reversible on GDSL3KC

series models.

• Read the instructions all the wag through before starting.

• Parts are included in the door hinge kit.

To order a reversible door hinge kit in the United States, visit our Website at GEAppliances.com

or call GE Parts and Accessories, 800.626.2002. Customers in Canada should consult the yellow

pages for the nearest IVlabe Service Center.

• Handle parts carefully to avoid scratching paint.

• Set screws down bg their related parts to avoid using them in the wrong places.

• Provide a non-scratching work surface for the doors.

IMPORTANT: Once gou begin, do not move the

cabinet until door-swing reversal is completed. These instructions are for changing the hinges

from the right side to the left side-if gou ever want to change the hinges back to the right side, follow

these same instructions and reverse all references to left and right.

• Once door swing is finalized, ensure the logo badge is properly aligned and permanentlg secured to the door by removing the adhesive cover on the back side. NOTE: A replacement logo badge is included in the hinge kit.

Unplug the refrigerator from its electrical outlet. Emptg all door shelves, including the dairg

compartment.

E] REMOVE THE

REFRIGERATOR DOOR

r_ Tape the door shut with masking tape.

r_ Remove the hinge cover on top of the

refrigerator door bg carefullg prging it up with a puttg knife, if necessarg.

r_ using a 5/16" socket ratchet/driver, remove

the bolts securing the top hinge to the cabinet. Then lift the hinge straight up to free the hinge pin from the socket in the top of the door.

r_ Carefullg remove the door thimble from inside

the socket. This will be used again when reinstalling the door on the other side.

Hinge Cover

TopHinge

qmbe

TOOLS YOU WILL NEED

Adjustable Wrench

MaskingTape

Phillips Screwdriver

5/16" Socket

Ratchet/Driver

Thin-blade Screwdriver

Torx T-20 Driver

[]

Remove the tape and tilt the door awag from the cabinet. Lift the door off the center hinge pin. Ensure that the plastic hinge pin thimble remains on the hinge pin or inside door hinge pin hole located in the bottom of the door.

r_ set the door on a non-scratching surface with

the inside up.

Installation Instructions

REVERSINGTHE DOOR SWING {cont.}

[] REMOVE THE FREEZER DOOR

r_ Tape the door shut with masking tape. r_ Remove hinge pin from hinge bracket. This will

be used again with the new hinge bracket for the other side.

Remove the tape and tilt the door awag from

the cabinet. Lift the door off the bottom hinge pin.

Remove the button plug from the left side of

the door. Remove the door thimble from the right side of the door. Install the door thimble

into the hole on the left and the button plug into the hole on the right.

TRANSFER CENTER HINGE BRACKET {cont.)

r_ Transfer the plug button and screw hole

cover in the hinge holes on the left side

to the right side.

E] Install the new center hinge bracket from the

kit on the left side.

r_ set the door on a non-scratching surface, with

the inside up.

[] TRANSFER CENTER HINGE BRACKET

r_ using a 5/16" socket ratchet/driver, remove the

bolts securing the center hinge to the cabinet.

REMOVE BOTTOM HINGE AND LEVELING LEG

Using a 1/2" socket ratchet/driver, remove the nut and hinge pin from the hinge bracket with leveling leg. Using a 5/16" socket ratchet/driver, remove the screws from the bottom hinge

bracket. These will be reinstalled on the other side.

Using a 5/16" socket ratchet/driver, remove the screws from the leveling leg bracket on

the other side. These will be reinstalled on the opposite side.

Installation Instructions

Fsl INSTALL BOTTOM HINGE AND

LEVELING LEG

r_ using a 1/2" socket ratchet/driver, install the

hinge pin and nut in the opposite hole on the hinge bracket with leveling leg.

r_ using a 5/16" socket ratchet/driver, install the

hinge bracket with leveling leg on the left side of the refrigerator. The pin will be toward the

outside of the refric erator.

[_] Using a 5/16" socket ratchet/driver, install the

leveling leg bracket on the right side of the refrigerator.

TRANSFER REFRIGERATOR AND

FREEZER DOOR STOPS

r_ Remove the door stop on the right side of the

bottom of the door bg removing the two screws.

r_ Move the plastic hinge hole thimble to the

opposite hole.

r_ Install the door stop on the left side, making

sure to line up the screw holes in the door stop

with the holes in the bottom of the door.

Bottom of Door(Right Side)

Bottom of Door (Left Side)

[_ TRANSFER REFRIGERATOR

DOOR HANDLE TO RIGHT

Refer to Remove the Fresh Food Door Handle

and Attach the Fresh Food Door Handle sections for instructions.

[_]REHANG FREEZER DOOR

[] Lower the freezer door onto the bottom hinge pin.

Ensure that the plastic hinge pin thimble is on the

hinge pin or inside the door hinge pin hole located

in the bottom of the door.

r_ straighten the door and line it up with the

center hinge bracket.

r_ Install the center hinge pin with a 3/4" socket

ratchet/driver. Turn it until it extends through

the hinge bracket and into the freezer door.

Installation Instructions

REVERSINGTHE DOOR SWING {cont.}

_-I REHANG REFRIGERATOR DOOR

rA] Lower the refrigerator door onto the center hinge

pin. Ensure that the plastic hinge pin thimble is on the center hinge pin or inside door hinge pin hole

located in the bottom of the door.

r_ Insert the door thimble into the hinge hole

on top of the refrigerator door and then insert the top hinge pin. Make sure the door is aligned with the cabinet. Attach the hinge to the top of the cabinet Iooselg with the bolts.

rc] Make sure the gasket on the door isflush against

the cabinet and is not folded. Support the door on the handle side and make sure the door is straight and the gap between the doors is even across the front. While holding the door in place, tighten the top hinge bolts. Replace the hinge cover.

INSTALL THE LOGO BADGE

Remove the adhesive backing paper

and align the pins on the back of the badge with the holes in the door. Apply pressure to the badge to ensure it sticks to the door.

Installation Instructions

REMOVING THE DOORS {Double Door RefrigeratorModels only)

IMPORTANT NOTES

NOTE: Door swing is not reversible.

• Read the instructions oil the wag through before starting.

Handle ports carefully to ovoid scratching point. Set screws down bg their related ports to ovoid

using them in the wrong places. Provide o non-scratching work surface for

the doors.

IMPORTANT: Once gou begin, do not move

the cabinet. These instructions ore for removing the doors.

Unplug the refrigerator from its electrical outlet. Emptg all door shelves, including the dairg

comportment.

TOOLS YOU WILL NEED

l_l REMOVE THE

REFRIGERATOR DOORS

r_ Tape the doors shut with masking tope.

@ Start with left-hand door first: Remove

the screw securing the center hinge cover, lift the hinge cover and place to the side on top of the refrigerator.

_" (1 Phillips screw)

Remove hinge cover

Adjustable Wrench

MaskingTape

Thin-blade Screwdriver

Phillips Screwdriver

318" and !0 mm Socket

Ratchet/Driver

r_ Remove the hinge cover on top of the

refrigerator door bg removing the Phillips head screw and pulling the cover up.

FD-]using o 5/16" socket ratchet/driver, remove

the bolts securing the top hinge to the cabinet. Then lift the hinge straight up to free the hinge pin from the socket in the top of the door.

Hinge Cover

Top Hinge

Installation Instructions

REMOVING THE DOORS {Double Door Refrigerator Models only){cont.}

m REMOVETHE REFRIGERATORDOORS

{cont.}

r_ set the door on a non-scratching surface with

the inside up.

I'_ REMOVE CENTER HINGE

Using a 5/16" socket ratchet/driver, remove the bolts securing the center hinge to the cabinet. Set the hinge and bolts aside.

.....iiii

[_] REMOVE OPPOSITE DOOR

Follow the same procedure on the opposite door. There are no center hinge covers on the opposite side.

[_] REMOVE FREEZER DRAWER

Refer to the Removing the Freezer Drawer section for instructions.

Installation Instructions

REPLACI NG TH E DOORS {Double Door Refrigerator Models onlg)

[i] INSTALL CENTER HINGE

Install the center hinge on each side.

ITI REHANG REFRIGERATOR DOORS

[] Lower the refrigerator door onto the center

hinge pin. Ensure that the plastic hinge pin

thimble is on the center hinge pin or inside

door hinge pin hole located in the bottom of the door.

FB1 Securelg tape the door shut with masking tape

or have o second person support the door.

r_ Insert the top hinge pin into the hinge hole on

top of the refrigerator door. Make sure the door

is aligned with the cabinet and opposite door.

Attach the hinge to the top of the cabinet

Iooselg with the bolts.

r_ Make sure the gasket on the door is flush

against the cabinet and is not folded. Make sure the door is straight and the gap between

the doors is even across the front. While

holding the aligned door in place, tighten

the top hinge bolts. Replace the hinge cover

and screw.

[_] REPLACE OPPOSITE DOOR

Follow the same procedure on the opposite

door. There is no water line or hinge cover.

143ALIGN DOUBLE DOORS

If the top of the doors are uneven, first trg to raise the lowest door bg turning the leveling leg

on the same side as the door until the doors are even. If the unit rocks, re-adjust the leveling

legs to the extent that the unit is stable.

If the doors remain uneven, turn the adjustable

pin to raise, or lower, the left door to match the right door. Use a 1/4" Allen wrench to turn the pin.

[_] REPLACE FREEZER DRAWER

Refer to the Replacing the Freezer Drawer section for instructions.

Hinge '°_

Bolts o

Top Hinge __

(appearance may vary)

_5_ _

Installation Instructions

INSTALLING THE WATER LINE (ICEMAKER MODELS}

BEFORE YOU BEGIN

Recommended copper water supplg kits are

WX8X2, WX8X3 or WX8X4, depending on the

amount of tubing gou need. Approved plastic

water supplg lines ore GE SmurtConnect"

Refrigerator Tubing (WXO8XIO006, WXO8X10015 and WXO8X10025).

When connecting gour refrigerator to a GE Reverse

Osmosis Water Sgstem, the onlg approved installation is with u GE RVKit. For other reverse

osmosis water systems, follow the manufacturer's recommendations.

If the water supplg to the refrigerator is from u Reverse Osmosis Water Filtration Sgstem

AND the refrigerator also has a water filter,

use the refrigerator's filter bgpass plug. Using

the refrigerator's water filtration cartridge in

conjunction with the RO filter con result in hollow ice cubes.

This water line installation is not warranted bg the refrigerator or icemaker manufacturer. Follow these instructions carefullg to minimize the risk of

expensive water damage.

Water hummer (water bunging in the pipes)in

house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supplg line to the refrigerator.

To prevent burns and product damage, do not hook

up the water line to the hot water line. If gou use gour refrigerator before connecting

the water line, make sure the icemoker power

switch is in the 0 {off} position. Do not install the icemaker tubing in areas where

temperatures full below freezing. When using ung electrical device (such as u power

drill) during installation, be sure the device is double insulated or grounded in u manner to prevent the hazard of electric shock, or is batterg powered.

All installations must be in accordance with local

plumbing code requirements.

WHAT YOU WILL NEED

• Copper or GE SmartConnect'" Refrigerator Tubing kit, 1/4" outer diameter to connect the

refrigerator to the water supplg. If using copper, be sure both ends of the tubing are cut square.

To determine how much tubing gou need: measure the distance from the water valve on the back

of the refrigerator to the water supplg pipe.

Be sure there is sufficient extra tubing to allow

the refrigerator to move out from the wall after installation.

GE SmartConnect T"Refrigerator Tubing Kits are available in the following lengths:

6' (1.8 m) - WXO8XIO006

15' (4.6 m) - WXO8X10015

25' (7.6 m) - WXO8X10025

+ 98 hidden pages