Fisher Paykel DD24DTI9N, DD24STI9N Installation Manual

DOUBLE DISHDRAWERTM DISHWASHER

DD24DI, DD24DTI & DD24DHTI models

INSTALLATION GUIDE

US CA

59186 A 08.17

1 SAFETY AND WARNINGS

WARNING!

Electrical Shock Hazard Before installing the dishwasher, remove the house fuse or open the circuit breaker. If permanently connecting the dishwasher, be sure the power is isolated and the dishwasher unplugged.

GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances. WARNING - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly grounded.

If the dishwasher is installed as a permanently connected appliance: GROUNDING INSTRUCTIONS - This appliance must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. Do not modify the power supply plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use an extension cord, adapter plug or multiple outlet box. Failure to follow this advice may result in electrical shock or death.

IMPORTANT SAFETY INSTRUCTIONS

●

Installation of this dishwasher requires basic mechanical and electrical skills.

●

Be sure to leave these Instructions with the Customer.

●

Installation must comply with your local building, electricity, and plumbing regulations.

●

At the completion of the dishwasher installation, the Installer must perform the Final Checklist.

●

Remove all packaging materials supplied with the dishwasher.

●

This dishwasher is manufactured for indoor use only.

●

Ensure all water connections are turned OFF. It is the responsibility of the plumber and electrician to ensure that each installation complies with all Codes and Regulations.

●

The dishwasher MUST be installed to allow for future removal from the enclosure if service is required.

●

The switched power outlet must be outside the dishwasher cavity, so that it is accessible after installation.

●

Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord and hoses.

●

If the dishwasher is to be relocated from one installation to another it must be kept upright to avoid damage from water spillage.

●

Make sure only new hoses are used for connection (supplied with the dishwasher). Old hoses should not be reused.

●

Failure to install the dishwasher correctly could invalidate any warranty or liability claims.

●

If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle, boat or mobile facility containing the product to the service shop at your expense or pay the service technician’s travel to the location of the product.

●

This dishdrawer is intended for connection to the hot-water supply.

●

Failure to install the dishwasher correctly could invalidate any warranty or liability claims.

WARNING!

Fitting integrated front panels requires access to electrical service areas. This work must be performed and certified by a qualified electrical service technician.

Electrical Shock Hazard WARNING: To reduce the risk of electrical shock, fire, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation. Before fitting the front panels and connecting the ‘knock to pause’ module (if necessary), the installer must ensure that the dishwasher is disconnected from the power supply. After installing the front panels, the installer must ensure that the following components are electrically grounded: the panel bracket and any custom metal component (e.g. handle) that extends past the rubber seal. Failure to follow these warnings may result in electrical shock, injury or fire.

WARNING!

Cut Hazard Take care - panel edges are sharp. Failure to use caution could result in injury or cuts.

●

Ensure the product is not plugged in when fitting custom panels.

●

Installation of custom panels requires basic mechanical and electrical skills.

●

Installation must comply with your local building and electricity regulations.

●

Failure to install the custom panels correctly could invalidate any warranty or liability claims.

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

2 PARTS SUPPLIED

Drain hose support (1)

Phillips 5/8” (16mm) screws (9)

Drain hose joiner (1)

for inlet hose (1)

(comes already fitted)

Wire clip (2)

(for securing Drain hose joiner)

Moisture protection tape (1)

(to prevent moisture damage to cabinetry)

Clamp (1)

(for securing Drain hose joiner)

Hexagonal socket for feet adjustment (2) (long & short)

Side mounting bracket kit (A and B) (2) OPTIONAL

Prefinished toekick (1) Rubber washer

Top mounting brackets (2) OPTIONAL

Edge Protector (1)

(If the services hole is through a metal partition, the hole must be protected with the Edge Protector supplied to prevent damage to the power cord or hoses.)

Panel bracket (2) & Knock-to-Pause Module (2)

(shipped fixed to product)

If the Drain hoses supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hoses by 11’ 10” (3.6m). The kit is available from the nearest Fisher & Paykel Authorized Service Center, or Toll free 1.888.936.7872 or www.fisherpaykel.com

Panel mounting screws (12)

Toekick mounting bracket cutting template (1)

(To enable a custom toekick panel to be cut to fit the product profile dependant on the depth of the toekick )

Toekick mounting bracket (1)

(A custom toekick panel of any material with thickness 3/8”- 3/4” (9 - 19mm) can be screwed to the Toekick mounting bracket)

Toekick mounting screws (5)

3 OPTIONALLY HARD WIRING PRIOR TO INSTALLATION

3-A REMOVE THE LOWER DRAWER 3-B REMOVE THE ACCESS COVER & REMOVE POWER

To prevent kinked hoses

Either sit the drawer down on the left hand side (recommended) or rotate the drawer clockwise, resting it on its side after removal.

4” (100 mm)

Press the release tabs in on either side and push back to release drawer from runners. Lift drawer off runners.

Push drawer runners back in on either side.

Sit the drawer down

Rotate the drawer clockwise (max. 90 and rest on side.

Clip

Access cover

1 With a flat-bladed screwdriver, push

in the clips and slide out the access cover.

2 Unscrew the electronics module

cover.

3 Carefully pull out the electronics

module and rest on the chassis base out of the way.

4 With a screwdriver, unclip the plastic

harness cover and hinge open.

5 Slide the terminal block cover

sideways to unlock and hinge open to access the terminal block.

6 Unscrew the Live, Neutral and Earth

wires as shown.

7 Unscrew the three screws on the

base as shown and remove the cord

)

from the product.

Remove existing power cord

Electronics module

Terminal Block cover

3-C TERMINATE MAINS WIRING AS SHOWN AND REPLACE MODULE AND COVERS

IMPORTANT!

Ensure the mains wires are routed UNDERNEATH all other harness wiring from the electronics module.

3 OPTIONALLY HARD WIRING PRIOR TO INSTALLATION

8 Fit a suitable cable clamp for the

conduit through the metal knockout.

Ensure wiring is routed through or

under under housing ribs.

9 Screw down the Live, Neutral and

Earth wires correctly.

10 Push the plastic harness cover back

over. It should clip back into place

11 Fold down and slide back the

terminal block cover.

12 Refit the electronics module back

into position, being careful of wiring.

13 Replace the screw securing the

electronics module.

14 Slide the access cover back,

ensuring the 2 clips shown are fully locked in place.

NOTE: Use copper conductors

only.

Before refitting the drawer, ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward.

3-D REFIT THE DRAWER ONTO THE RUNNERS & CLOSE

Lift or rotate counter-clockwise the drawer back onto the drawer runners on either side.

4” (100 mm)

Release tab

Pull the release tabs forward on both sides 4” (100 mm). Ensure the tabs are fully pulled forward and click into place.

4 PRODUCT DIMENSIONS

PROFILEFRONT

STANDARD

HEIGHT

MODELS

DD24DI

PRODUCT DIMENSIONS INCHES (MM) INCHES (MM)

Overall height of product

PLAN

Overall width of product

Overall depth of product

Depth of chassis (to back of front drawer panel)

Depth of drawer front panel

Height of chassis

Height of drawer front panels

Height of upper drawer front panel

Height of lower drawer front panel

Ventilation gap between drawer front panels

Height of toekick (customisable)

Depth from front of drawer panel to front of toekick (adjustable)

Height of leveling feet (adjustable)

Maximum extension of drawer

includes 1/16” (2mm) high bracket slots 2 depending on adjustment of leveling feet 3 assuming front panel thickness of 11/16” (18mm)

adjustable to match toekick recess on adjoining cabinetry

assuming custom toekick panel thickness of 11/16” (18mm); if recess is between 1 15/16”-3 5/16” (50-84mm) deep, the panel will need to be cut out -

see step ‘Custom panel calculations’

1, 2

4, 5

32 5/16 - 34 5/8” (820-880) 34 - 36 3/8” (864-924)

23 9/16” (599) 23 9/16” (599)

22 1/2” (571) 22 1/2” (571)

21 3/4” (553) 21 3/4” (553)

5/8” - 13/16” (16-20) 13/16” (20)

31 15/16” (811) 33 11/16” (855)

min. 28 1/4” (717) 29 15/16” (761)

min 15 11/16” (398) min. 17 3/8” (442)

12 1/4” - 14 3/16” (311-360) 12 1/4” - 14 3/16” (311-360)

5/16” (8) 5/16” (8)

2 1/4” - 4 5/8” (58-118) 2 1/4” - 4 5/8” (58-118)

1 9/16” - 3 15/16” (40-100) 1 9/16” - 3 15/16” (40-100)

3/8 - 2 11/16” (9-69) 3/8 - 2 11/16” (9-69)

21 7/16” (545) 21 7/16” (545)

TALL

HEIGHT

MODELS

DD24DTI

DD24DHTI

5 CABINETRY DIMENSIONS

Bracket slots

PLAN

STANDARD

HEIGHT

MODELS

DD24DI

CABINETRY DIMENSIONS INCHES (MM) INCHES (MM)

Inside height of cavity* min. 32 5/16” (820) min. 34” (864)

Inside width of cavity 23 5/8” (600) 23 5/8” (600)

Inside depth of cavity min. 22 1/16” (560) min. 22 1/16” (560)

Recommended height of adjacent cabinet space 30” (762) 30” (762)

Height of toekick space*

* depending on adjustment of leveling feet

2 3/8 - 4 3/4” (60-120) 3 15/16” - 6 5/16” (100-160)

TALL

HEIGHT

MODELS

DD24DTI

DD24DHTI

PROFILE

Minimum clearances from adjacent cabinetry

min. 1/2” (13 mm) clearance from a corner cupboard

min. 1/16” (2 mm) clearance to adjacent cupboard door

6 CUSTOM DRAWER PANEL SPECIFICATIONS

FRONT PANEL MATERIAL SPECIFICATIONS

●

5/8 - 13/16” (16 - 20mm) panel thickness.

●

Adequately sealed to withstand moisture (122OF/50OC @ 80% RH) Because of it being a hot and wet environment generally, the back and sides of the panel should be completely sealed with a waterproof vapor barrier (ie polyurethane) to prevent damage to the panel.

●

The back of the panel (including any integrated handle) should be completely flush so that the seal between the panel and the rubber trim is maintained.

●

Installation outside these specs may result in condensation on cabinetry surfaces.

●

Maximum weight of each panel: 20lb (9kg)

The following calculations assume the top of the upper panel is aligned with the top of the adjacent cabinetry. The final panel/cabinetry alignment is achieved by adjusting the feet:

WIDTH OF ALL PANELS

Measure A (the width between adjacent door/drawer fronts) and write it in the first box below, then complete the equation.

Note: The ‘upper panel extension’ B allows for the top of the upper panel to extend above the chassis where required, however a min. 1/16” (2mm) gap to the countertop must be maintained.

min. 1/16”

(2mm)

Clearance to adjacent

cabinet front

- 2x =

(min. 1/16” (2mm))

HEIGHT OF THE UPPER PANEL

Minimum height

DD24DI models:

15 11/16”

DD24DTI/DD24DHTI models:

17 3/8”

Note: The ‘upper panel extension’ B allows for the top of the upper panel to extend above the chassis where required, however a min. 1/16” (2mm) gap to the countertop must be maintained.

HEIGHT OF THE LOWER PANEL

Measure C (door/drawer height (or equivalent)) and write it in the first box below, then complete the equation.

(398mm)

(442mm)

Upper Panel extension

(0”/0mm recommended)

DD24DI models:

(min 28 1/4” (717mm) +

DD24DTI/DD24DHTI models:

(min 30” (762mm) +

Height of

Upper Panel

Ventilation Gap

(min. 5/16” (8mm))

(23 7/16”-24 3/16” (596-615mm))

WIDTH OF PANEL

HEIGHT OF

UPPER PANEL

HEIGHT OF

LOWER PANEL

(min. 12 1/4” (311mm))

min. 1/16” (2mm)

UPPER PANEL

LOWER PANEL

TOEKICK PANEL

WIDTH OF ALL PANELS

min. 1/16” (2mm)min. 1/16” (2mm)

HEIGHT OF UPPER PANEL

Ventilation Gap (min. 5/16” (8mm))

HEIGHT OF LOWER PANEL

7 CUSTOM TOEKICK PANEL SPECIFICATIONS

TOEKICK PANEL MATERIAL SPECIFICATIONS

●

min. 3/8” (9mm) panel thickness if using supplied screws

●

Adequately sealed to withstand moisture (122OF/50OC @ 80% RH)

●

You may choose to affix your custom toekick panel either by screwing it or gluing it to the supplied mounting bracket.

HEIGHT OF THE TOEKICK PANEL

Measure D (height from the top of adjacent cabinet door fronts to the floor) and write it in the first box below, then complete the equation.

Upper Panel

extension

(0”/0mm

recommended)

height from top

of product to

toekick panel

mounting point

DD24DI models:

29 1/2”

31 1/4”

(750mm)

DD24DTI/DD24DHTI models:

(794mm)

Clearance to floor

(min. 1/2” (12mm))

HEIGHT OF

TOEKICK PANEL

=-- -

(min. 2 1/4” (58))

Toekick Depth

Depth is measured from FRONT of door panel (assuming thickness ~ 11/16” (18mm) to front face of custom toekick label

NO CUTOUT

CUSTOM TOEKICK PANEL

For a Toekick Depth

1 9/16” (40mm)

Height from top of product to toekick panel mounting point

DD24DI models:

29 1/2”

DD24DTI/DD24DHTI models:

31 1/4”

(750mm)

(794mm)

Toekick mounting bracket

cutting template:

PROFILE A

CUSTOM TOEKICK PANEL

For a Toekick Depth

1 9/16” - 3 7/16”

(40mm - 88mm)

Toekick mounting bracket

1 9/16” (40mm)

1 9/16” - 3 7/16” (40mm - 88mm)

cutting template:

PROFILE B

CUSTOM TOEKICK PANEL

HEIGHT OF TOEKICK PANEL

Clearance to floor (min. 1/2” (12mm))

For a Toekick Depth

3 7/16” - 3 15/16”

(88mm - 100mm)

3 7/16” - 3 15/16” (88mm - 100mm)

COUNTERTOP

3/8” (10 mm)

Moisture protection tape must be applied.

8 CAVITY PREPARATION

IMPORTANT!

The power outlet must be located in a cabinet adjacent to the dishwasher cavity. 110-120 VAC max. 15 A

Water Connection

Recommended HOT (Maximum 140°F/60°C).

Supplied hose to suit 3⁄8” (9 mm) male compression fitting.

These marks indicate formed bracket screw locations, if securing by drawer removal.

If there is no side partition, you can construct timber bracing as something to secure into.

Services hole

Can be located either side of dishwasher, preferably at the bottom of the cavity, as shown. If adequate clearance, services hole can be made higher to clear toekick space. If hole is higher, ensure drain hose(s) are routed straight into the waste connection.

●

If the hole is through wood, make sure its edges are smooth and rounded.

●

If the hole is through metal, ensure you fit the supplied Edge Protector to prevent damage to the power cord.

ø max. 1 1/2” (38 mm)

max. 17 11⁄16” (450 mm)

Water Pressure

Water softener models

Max. 1 MPa (145 psi) Min. 0.1 MPa (14.5 psi)

Models without water softener

Max. 1 MPa (145 psi) Min. 0.03 MPa (4.3 psi)

Kosher requirements

Drains will need to be separated to satisfy kosher requirements. We suggest you confirm acceptability with your local rabbi in respect to kosher installations.

min. 7 7⁄8” (200 mm)

9 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE

LEFT HAND SIDE RIGHT HAND SIDE

Drain hoses - 78 1/2” (2000mm)

Inlet hose - 64 3/4” (1650mm)

Power cord (excl.plug) - 29 1/2” (750mm)

Drain hoses - 70 1/2” (1800mm)

Inlet hose - 49” (1250mm)

Power cord (excl.plug) - 27 1/2” (700mm)

NOW CHOOSE WHICH INSTALLATION METHOD (A) OR (B)

IS MORE SUITABLE FOR YOUR CABINETRY...

!0 RECOMMENDED METHOD (A) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY)

!0-A ATTACH SIDE MOUNTING BRACKETS !1-A PULL THROUGH HOSES & PUSH INTO THE CAVITY

Clip all four side mounting brackets into their slots using a flat-bladed screwdriver. Ensure they’re securely fitted before sliding product into cavity.

optionally attach the two top mounting brackets

(x2)

Initially level the product

When fitting brackets, ensure the ends are not pushed down into the chassis.

The mounting slots are in pairs, one on each side diagonally across the product. A bracket must match A slot and B bracket must match B slot.

When fitting brackets, ensure the ends are not pushed down into the chassis.

You can raise or lower the product by twisting the feet. Then take care when pushing the product into the cavity that you do not bend the feet.

As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted.

!2-A SECURE TO THE CABINETRY ON THE SIDES

!3-A OPTIONALLY SECURE TO THE CABINETRY ABOVE

Using a small

Philips screwdriver,

screw through the

trim moulding,

securing the side

mounting bracket

to the cabinetry.

Do not damage

the rubber

trimseal.

Open the

drawer halfway.

Using a flat

bladed

screwdriver,

prise the gray

rubber plug out

of the trim

moulding.

Repeat for all four brackets.

Replace the gray rubber plug back into the trim moulding and ensure the trim seal is facing forward.

The top mounting brackets will only

(x2)

bend upwards a maximum of 3⁄8” (10 mm).

!4-A AFTER SECURING, REFER TO ‘FIT THE SUPPLIED TOEKICK PANEL’ STEP

!0 ALTERNATIVE METHOD (B) - SECURE BY DRAWER REMOVAL

!0-B PULL THROUGH HOSES & PUSH INTO THE CAVITY !1-B REMOVE THE LOWER DRAWER

optionally attach the two top mounting brackets

(x2)

Initially level the product

You can raise or lower the product by twisting the feet. Then take care when pushing the product into the cavity that you do not bend the feet.

When fitting brackets, ensure the ends are not pushed down into the chassis.

As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted.

4” (100mm)

Press the release tabs in on either side and push back to release drawer from runners. Lift drawer off runners.

To prevent kinked hoses

Either sit the drawer down on the left hand side (recommended) or rotate the drawer clockwise, resting it on its side after removal.

Push drawer runners back in on either side.

Sit the drawer down

Push drawer runners back in on either side.

Rotate the drawer clockwise (max. 90 and rest on side.

)

!2-B SECURE TO THE CABINETRY ON THE SIDES !3-B OPTIONALLY SECURE TO THE CABINETRY ABOVE

For further adjustment, using the most appropriate length Hexagonal socket supplied, fully extend levelling feet up to required distance by hand.

Secure using two pairs of formed brackets. Repeat on the other side of the chassis.

(x2)

The top mounting brackets will only bend upwards a maximum of 3⁄8” (10 mm).

Before refitting the drawer, ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward.

Hexagonal socket

Ensure product is level and aligning with cabinetry.

!4-B REFIT THE DRAWER ONTO THE RUNNERS

Lift or rotate counterclockwise the drawer back onto the drawer runners on either side.

4” (100mm)

Pull the release tabs forward on both sides 4” (100mm). Ensure the tabs are fully pulled forward and click into place.

Release tab

!5 INSTALLING CUSTOM FRONT DRAWER PANELS

!5-B REMOVE BOTH PANEL BRACKETS FROM PRODUCT

WARNING!

Side Pin

Remove side pins and gently pull off the panel bracket slightly.

Electrical Shock Hazard

Before continuing, ensure that the product is disconnected from the power supply. Failure to follow this warning may result in electrical shock, injury or ﬁre.

!5-B REMOVE THE KNOCK-TO-PAUSE MODULE

Knock-to-Pause module

Repeat for the other drawer.

1 Disconnect the Earth Wire

from the bracket

2 Unplug the knock sensor

from the controller.

Repeat for the other drawer.

Remove the Knock-to-Pause module from the back of the bracket.

Repeat for the other bracket.

+ 36 hidden pages