MXD426BT
INSTALLATION/OWNER'S MANUAL
AM/FM/CD Receiver with Detachable Face
Fronta d RearInputs
MXD426BT INSTALLATION
Preparation
Please read entire manual before installation.
Before You Start
•Disconnect negative battery terminal. Consult a qualified technician for instructions.
•Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
•Remove trim ring from unit.
•Remove 2 transit screws located on top of the unit.
•Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve.
•Install mounting sleeve into opening, bending tabs to secure.
•Connect wiring harness and antenna. Consult a qualified technician if you are unsure.
•Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately).
•Test for correct operation and slide into mounting sleeve to secure.
•Snap trim ring into place.
MOUNTING SLEEVE
REMOVAL KEYS
HEAD UNIT
INSTALLATION
MOUNTING KITS
OR DASHBOARD
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
2
MXD426BT INSTALLATION
Wiring Diagram
Antenna
Connector
10 AMP
AGC Fuse
FUSE
When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could
damage the radio. The MXD426BT uses one 10 amp AGC fuse located beside the wiring connector.
3
MXD426BT OPERATION
Control Locations - Receiver
1 |
2 |
3 |
4 |
5 |
6 |
7 |
19 |
18 |
17 |
16 |
15 |
14 |
13 |
12 |
11 |
10 |
9 |
8 |
1. |
Release |
|
10. |
Preset 4 / Play / Pause |
2. |
Band / Go Back |
|
11. |
Preset 3 / Intro |
3. |
Volume / Select |
|
12. |
Preset 2 / Random |
4. |
Power / Mute |
|
13. |
Preset 1 / Repeat |
5. |
USB Port |
|
14. |
Display |
6. |
Eject |
|
15. |
Tune / Track Up |
7. |
Auxiliary Input |
|
16. |
Tune / Track Down |
8. |
Preset 6 / Folder Up |
17. |
Mode |
|
9. |
Preset 5 / Folder Down |
18. |
Audio / Menu |
|
|
|
|
19. |
Bluetooth Talk |
|
1 |
2 |
|
|
|
3 |
|
4 |
17 |
5 |
|
|
|
6 |
16 |
7 |
|
|
15 |
8 |
|
|
14 |
9 |
|
|
|
10 |
13 |
|
|
11 |
12 |
|
1.Mode
2.Volume Up
3.Power
4.Select
5.Tune / Track Up
6.Volume Down
7.Band / Go Back
8.Preset 3 / Intro
9.Preset 2 / Random
10.Preset 6 / Folder Up
11.Mute
12.Audio / Menu
13.Preset 5 / Folder Down
14.Preset 4 / Play / Pause
15.Preset 1 / Repeat
16.Bluetooth Talk
17.Tune / Track Down
4
MXD426BT OPERATION
General Operation
Power On/Off Press or any other button (except EJECT) to turn the unit on. Press to turn the unit off.
Mode Press MODE to select between AM/FM, CD player, auxiliary front/rear, USB and Bluetooth. Modes of operation are shown in the display.
NOTE: CD and USB modes will not appear unless a CD is inserted or USB device is connected.
Auxiliary Input The MXD426BT offers a 3.5 mm port on the front panel to connect audio device, MP3 player, etc. Press MODE to select
AUX mode.
Volume Adjust volume using volume knob (00-46).
Display Press DISP to select between clock and different types of information, such as radio frequency, CD track/elapsed time
or MP3/WMA song information.
Reset Press RESET upon initial installation or if abnormal operation occurs. Reset button is located behind the front panel.
Set the Clock With the unit on, press and hold DISP until the clock begins to flash, then release. Press TUNE nnto adjust the hours
and TUNE llto adjust the minutes. Press DISP momentarily to save the selected time.
12/24-hour Clock The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing
mode, the clock will display 24-hour time (22:00).
Setup Menu Press and hold AUDIO/MENU for more than 3 seconds to access the setup menu. Press AUDIO/MENU momentarily
to select between the menu functions and rotate the volume knob left/right to adjust or activate the desired function.
5
MXD426BT OPERATION
General Operation - Setup Menu
Menu Function |
Options |
Action |
|
|
Auto Station |
AUTO STORE |
Press SELECT to seek and save 6 strong stations in the |
|
|
Store |
current band. (Tuner mode only) |
|
|
|
|
|
|
||
Local/Distance |
LOCAL OFF |
Activates distance tuning (Tuner mode only). |
|
|
|
Activates local tuning for strong station reception only (Tuner |
|
||
Tuning |
LOCAL ON |
|
||
|
mode only). |
|
|
|
|
|
|
|
|
Tuner |
FREQ USA |
Programs the unit to USA tuner spacing. |
|
|
(200kHz for FM and 10kHz for AM). (Tuner mode only) |
|
|||
|
|
|||
Frequency |
|
|
|
|
|
Programs the unit to European tuner spacing. |
|
||
Spacing |
FREQ EURO |
|
||
|
(50kHz for FM and 9kHz for AM). (Tuner mode only) |
|
||
|
|
|
||
Auxiliary |
AUX ON |
Enables the front panel 3.5mm auxiliary input. |
|
|
Input |
AUX OFF |
Disables the front panel 3.5mm auxiliary input. |
|
|
|
|
|||
Beep |
BEEP OFF |
Disables the confirmation beep. |
|
|
Confirmation |
BEEP ON |
Enables the confirmation beep. |
|
|
|
|
|
||
Programmable |
PRO-VOL # |
Programs unit to always turn on at a specific volume |
|
|
Turn On Volume |
(default is OFF). Any volume level 1-30 can be selected. |
|
||
|
|
|||
Power on |
MSG OFF |
Disables power on message. (example: GOOD MORNING) |
|
|
Message |
MSG ON |
Enables power on message to be displayed. |
|
|
|
|
|||
|
SCROLL 15 S |
Programs unit to scroll information every 15 seconds (default). |
|
|
Scrolling |
SCROLL ONCE |
Programs unit to scroll once, then show the first 10 characters |
|
|
on display. |
|
|
||
Option |
|
|
|
|
SCROLL ON |
Programs unit to scroll continuously. |
|
||
|
|
|||
|
SCROLL OFF |
Programs unit to show the first 10 characters on the display. |
|
|
Demonstration |
DEMO OFF |
Disables the demonstration mode. |
|
|
Mode |
DEMO ON |
Enables the demonstration message. |
|
|
|
|
|||
|
LED AUTO |
Programs unit to automatically rotate through all LED colors. |
|
|
|
BLUE |
Programs unit to use blue LED display. |
|
|
|
|
|
|
|
|
GREEN |
Programs unit to use green LED display. |
|
|
|
|
|
|
|
|
RED |
Programs unit to use red LED display. |
|
|
|
|
|
|
|
LED Color |
YELLOW |
Programs unit to use yellow LED display. |
|
|
|
PURPLE |
Programs unit to use purple LED display. |
|
|
|
|
|
|
|
|
CYAN |
Programs unit to use cyan LED display. |
|
|
|
|
|
|
|
|
WHITE |
Programs unit to use white LED display. |
|
|
|
|
|
|
|
|
LED ADJ |
Press and rotate the volume knob to adjust each RGB color |
|
|
|
level. After adjustment, that color will appear on the LCD. |
|
||
|
|
|
||
Bluetooth |
BT ON |
Enables Bluetooth functionality. |
|
|
|
|
|
|
|
BT OFF |
Disables Bluetooth functionality. |
|
|
|
|
|
|
||
|
|
|
|
|
|
ANSWER ON |
Programs unit to automatically answer every incoming phone |
|
|
|
call after 2-3 rings. |
|
|
|
Auto Answer |
|
|
|
|
ANSWER OFF |
Programs unit to require the |
button must be pressed to |
|
|
|
|
|||
|
answer incoming phone calls. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6
MXD426BT OPERATION
General Operation
Audio Press AUDIO/MENU momentarily to select between Bass, Treble, Balance, Fader, Subwoofer and Source Volume Level.
BASS TREBLE BALANCE FADER EQ LOUDSOURCE LEVEL
Bass Press AUDIO/MENU until BASS appears then rotate volume knob left/right to adjust ( -6 minimum / +6 maximum).
Treble Press AUDIO/MENU until TREBLE appears then rotate volume knob left/right to adjust ( -6 minimum / +6 maximum).
Balance Press AUDIO/MENU until BAL appears then rotate volume knob left/right to adjust (BAL LEFT 12 - BAL RIGHT 12). BAL EVEN represents equal balance
Fader Press AUDIO/MENU until FADER appears then rotate volume knob left/right to adjust (FADER FRONT 12 - FADER REAR 12). FADER EVEN represents equal fader
EQ Press EQ, then turn the volume knob to cycle through the following equalization curves: FLAT (default), POP, JAZZ, CLASSIC, BEAT, ROCK and USER. Any manual adjustment to the Bass or Treble settings are automatically saved as USER.
Loudness Press AUDIO/MENU until LOUD appears then rotate volume knob left/right to adjust LOUD ON/OFF.
Source Volume Level The source volume level control allows a gain adjustment for each audio source: AM, FM, CD, AUX and USB. Set the source volume level for each mode, depending on the relative volume of each audio source.
To set the source volume level, press AUDIO/MENU until SRC LEVEL appears. After one second, the current mode will appear on the display. Turn the volume knob to adjust the audio level of the current source (-3 minimum/+3 maximum).
Note: Only the current mode will be available for adjustment. To adjust another mode of operation, press MODE until the desired mode is selected, then set the
source volume level for that mode.
7
MXD426BT OPERATION
AM/FM Tuner Operation
Seek Tuning Press TUNE nnor TUNE llfor more than one second to seek to the next strong station.
Manual Tuning Press TUNE nnor TUNE llmomentarily to change radio frequency up or down one step at a time. Press and hold to advance quickly.
Band Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands.
Storing and Recalling Up to 18 FM stations and 12 AM stations can be stored. To Station Presets store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
2 seconds. When stored, the preset number will appear in the display. The station can be recalled anytime by pressing the corresponding preset button.
Automatically Store Press and hold AUDIO/MENU for more than 3 seconds to Stations find auto store in the display, then press the volume knob to
automatically store strong 6 stations in the current band.
8