DM 2610031482 05-13_MM30 5/28/13 8:11 AM Page 1
IMPORTANT: |
IMPORTANT : |
IMPORTANTE: |
Read Before Using |
Lire avant usage |
Leer antes de usar |
|
|
|
Operating/Safety Instructions 
Consignes de fonctionnement/sécurité
Instrucciones de funcionamiento y seguridad
MM30
P.O. Box 081126 Racine, WI 53408-1126
|
Call Toll Free for |
Pour obtenir des informations |
Llame gratis para |
|
|
Consumer Information |
et les adresses de nos centres |
obtener información |
|
||
|
& Service Locations |
de service après-vente, |
para el consumidor y |
|
|
|
|
appelez ce numéro gratuit |
ubicaciones de servicio |
|
|
|
|
|
|
||
|
1-800-4-DREMEL (1-800-437-3635) www.dremel.com |
|
|
||
|
|
|
|
|
|
For English Version |
Version française |
Versión en español |
|
||
|
See page 2 |
Voir page 19 |
Ver la página 36 |
|
|
|
|
|
|
|
|
DM 2610031482 05-13_MM30 5/28/13 8:11 AM Page 2
|
General Power Tool Safety Warnings |
|
Read all safety warnings and all instructions. Failure to follow the warnings |
! WARNING |
|
|
and instructions may result in electric shock, fire and/or serious injury. |
|
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Work area safety
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical safety
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
If operating the power tool in damp locations is unavoidable, use a Ground Fault Circuit Interrupter (GFCI) protected supply. Use of an GFCI reduces the risk of electric shock.
Personal safety
Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and / or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dustrelated hazards.
Power tool use and care
Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
-2-
DM 2610031482 05-13_MM30 5/28/13 8:11 AM Page 3
Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Service
Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
Safety Rules for Oscillating Tools
Hold power tool by insulated gripping surfaces, when performing an operation where the cutting tool may contact hidden wiring or its own cord. Cutting tool contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.
Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.
Do not drill, fasten or break into existing walls or other blind areas where electrical wiring may exist. If this situation is unavoidable, disconnect all fuses or circuit breakers feeding this worksite.
Use a metal detector to determine if there are gas or water pipes hidden in the work area or call the local utility company for assistance before beginning the operation.
Striking or cutting into a gas line will result in explosion. Water entering an electrical device may cause electrocution.
Always hold the tool firmly with both hands for maximum control. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
Keep hands away from cutting area. Do not reach under the material being cut. The proximity of the blade to your hand is hidden from your sight.
Do not use dull or damaged blades. Bent blade can break easily or cause kickback.
Exercise extreme caution when handling the accessories. The accessories are very sharp.
Wear protective gloves when changing cutting accessories. Accessories become hot after prolonged usage.
Use thick cushioned gloves and limit the exposure time by taking frequent rest periods. Vibration caused by the tool may be harmful to the hands and arms.
Before scraping, check workpiece for nails. If there are nails, either remove them or set them well below intended finished surface.
Striking a nail with accessory edge could cause the tool to jump.
Do not wet sand with this tool. Liquids entering the motor housing is an electrical shock hazard.
Never work in area which is soaked with a liquid, such as a solvent or water, or dampened such as newly applied wallpaper. There is an electrical shock
-3-
DM 2610031482 05-13_MM30 5/28/13 8:11 AM Page 4
hazard when working in such conditions with a power tool and heating of the liquid caused by scraping action may cause harmful vapors to be emitted from workpiece.
Always wear eye protection and a dust mask for dusty applications and when sanding overhead. Sanding particles can be absorbed by your eyes and inhaled easily and may cause health complications.
Use special precautions when sanding chemically pressure treated lumber, paint that may be lead based, or any other materials that may contain carcinogens. A suitable breathing respirator and protective
clothing must be worn by all persons entering the work area. Work area should be sealed by plastic sheeting and persons not protected should be kept out until work area is thoroughly cleaned.
Do not use sandpaper intended for larger sanding pads. Larger sandpaper will extend beyond the sanding pad causing snagging, tearing of the paper or kick-back. Extra paper extending beyond the sanding pad can also cause serious lacerations.
Additional Safety Warnings
GFCI and personal protection devices like electrician’s rubber gloves and footwear will further enhance your personal safety.
Do not use AC only rated tools with a DC power supply. While the tool may appear to work, the electrical components of the AC rated tool are likely to fail and create a hazard to the operator.
Keep handles dry, clean and free from oil and grease. Slippery hands cannot safely control the power tool.
Develop a periodic maintenance schedule for your tool. When cleaning a tool be careful not to disassemble any portion of the tool since internal wires may be misplaced or pinched or safety guard return springs may be improperly mounted.
Certain cleaning agents such as gasoline, carbon tetrachloride, ammonia, etc. may damage plastic parts.
Risk of injury to user. The power cord must only be serviced by a Dremel Service Facility.
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
•Lead from lead-based paints,
•Crystalline silica from bricks and cement and other masonry products, and
•Arsenic and chromium from chemicallytreated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
-4-
DM 2610031482 05-13_MM30 5/28/13 8:11 AM Page 5
Symbols
IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
Symbol |
Name |
Designation/Explanation |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
V |
Volts |
Voltage (potential) |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
A |
Amperes |
Current |
|||||
|
|
|
|
|
|
|
|
|
|
|
Hz |
Hertz |
Frequency (cycles per second) |
||||||
|
|
|
|
|
|
|
|
|
|
|
W |
Watt |
Power |
||||||
|
|
|
|
|
|
|
|
|
|
|
kg |
Kilograms |
Weight |
||||||
|
|
|
|
|
|
|
|
|
|
min |
Minutes |
Time |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
s |
Seconds |
Time |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Diameter |
Size of drill bits, grinding wheels, etc. |
|
|
|
|
|
|
|
|
|
|
|
n0 |
No load speed |
Rotational speed, at no load |
||||||
|
|
n |
Rated speed |
Maximum attainable speed |
|||||
|
|
|
|
|
|
|
|
|
|
.../min |
Revolutions or reciprocation |
Revolutions, strokes, surface speed, |
|||||||
|
|
|
|
|
|
|
|
per minute |
orbits etc. per minute |
|
|
|
|
|
|
|
|
|
|
0 |
|
|
|
Off position |
Zero speed, zero torque... |
||||
|
|
|
|
|
|
|
|
|
|
1, 2, 3, ... |
Selector settings |
Speed, torque or position settings. |
|||||||
I, II, III, |
|
Higher number means greater speed |
|||||||
|
|
|
|
|
|
|
|
|
|
0 |
|
|
|
|
|
|
Infinitely variable selector with off |
Speed is increasing from 0 setting |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Arrow |
Action in the direction of arrow |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Alternating current |
Type or a characteristic of current |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Direct current |
Type or a characteristic of current |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Alternating or direct current |
Type or a characteristic of current |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Class II construction |
Designates Double Insulated |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
Construction tools. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Earthing terminal |
Grounding terminal |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Warning symbol |
Alerts user to warning messages |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Li-ion RBRC seal |
Designates Li-ion battery recycling |
|
|
|
|
|
|
|
|
|
program |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ni-Cad RBRC seal |
Designates Ni-Cad battery recycling |
|
|
|
|
|
|
|
|
|
program |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Read manual symbol |
Alerts user to read manual |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Wear eye protection symbol |
Alerts user to wear eye protection |
|
|
|
|
|
|
|
|
|
|
-5-
DM 2610031482 05-13_MM30 5/28/13 8:11 AM Page 6
Symbols (continued)
IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
This symbol designates that this tool is listed by Underwriters Laboratories.
This symbol designates that this tool is recognized by Underwriters Laboratories.
This symbol designates that this tool is listed by Underwriters Laboratories, to United States and Canadian Standards.
This symbol designates that this tool is listed by the Canadian Standards Association.
This symbol designates that this tool is listed by the Canadian Standards
Association, to United States and Canadian Standards.
This symbol designates that this tool is listed by the Intertek Testing
Services, to United States and Canadian Standards.
This symbol designates that this tool complies to NOM Mexican Standards.
-6-
DM 2610031482 05-13_MM30 5/28/13 8:11 AM Page 7
Functional Description and Specifications
Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety
measures reduce the risk of starting the tool accidentally.
Model MM30 Multi-Max™ Oscillating Power Tool
FIG. 1
Variable Speed
Control Dial
On/Off
Switch
Power Cord
Quick Release
Wrench
Ventilation
Openings
Ventilation
Openings
Clamping
Screw
Blade
Washer
Accessory |
|
Magnetic Accessory |
|
|
Holder |
Model number |
MM30 |
No load speed |
n0 10,000-23,000/min |
Voltage rating |
120 V 60 Hz |
NOTE: For tool specifications refer to the nameplate on your tool.
-7-
DM 2610031482 05-13_MM30 5/28/13 8:11 AM Page 8
Assembly
! WARNING Disconnect the plug from the power source before
making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally.
For all work or when changing accessories always wear protective gloves. Such
preventive safety measures reduce the risk of injury from sharp edges of the accessories. Application tools can become very hot while working. Danger of burns!
INSTALLING AND REMOVING ACCESSORIES WITH qUICK-RELEASE ACCESSORy CHANGE
The Dremel Multi-Max MM30 includes an integrated wrench system which allows users to quickly and easily change accessories.
1.Push down on wrench release button (blue) and push wrench forward to release wrench. Pivot out the socket head (Fig. 2).
2.Loosen the clamping screw just enough so you can slide the accessory between the accessory holder and washer (Fig. 3).
3.Clean the accessory holder, accessory, and clamping screw with a clean cloth.
4.Place the accessory onto the accessory holder, making sure the accessory engages all pins in the holder and the accessory is flush against the accessory holder.
5.Securely tighten the clamping screw with the Quick-Release wrench (Fig. 4) and place it back onto the tool. The wrench should snap back onto the tool.
NOTE: Some accessories, such as scrapers or blades, may be mounted either straight on the tool, or at an angle to enhance usability (Fig. 5).
FIG. 2 |
1 |
2
3
FIG. 3
|
Clamping |
Accessory |
Screw |
Holder |
|
Blade 
Washer
Accessory
Quick Release
Wrench
Accessory |
FIG. 5 |
FIG. 4 |
Quick
Release
Wrench
Clamping
Screw
-8-
DM 2610031482 05-13_MM30 5/28/13 8:11 AM Page 9
INSTALLING AND REMOVING
SANDING SHEETS
Your backing pad uses hook-and-loop backed sandpaper, which firmly grips the backing pad when applied with moderate pressure.
1.Align the sanding sheet and press it onto the sanding plate by hand.
2.Firmly press the power tool with the sanding sheet against a flat surface and briefly switch the power tool on. This will promote good adhesion and helps to prevent premature wear.
3.To change, merely peel off the old sanding sheet, remove dust from the backing pad if necessary, and press the new sanding sheet in place.
After considerable service the backing pad surface will become worn, and the backing pad must be replaced when it no longer offers a firm grip. If you are experiencing premature wear out of the backing pad facing, decrease the amount of pressure you are applying during operation of the tool.
For maximum use of abrasive, rotate pad 120 degrees when tip of abrasive becomes worn.
Introduction
Thank you for purchasing the Dremel MultiMax™.
This tool was designed to tackle home repair, remodeling and restoration projects. The Dremel Multi-Max™ tackles tasks that are tedious, time consuming or simply next to impossible to achieve with any other tool. The ergonomic housing is designed for you to hold and control in a comfortable manner during operation.
It comes with an assortment of accessories that are specifically designed for remodeling work where you need precision and control.
Your Dremel Multi-Max™ has a robust electric motor, is comfortable in the hand, and is made to accept a large variety of accessories including flush cut blades,
scraper blades, grout removal wheels and sanding pads.
Accessories come in a variety of shapes and permit you to do a number of different jobs. As you become familiar with the range of accessories and their uses, you will learn just how versatile your Dremel Multi-Max™ is.
Visit www.dremel.com to learn more about what you can do with your Dremel MultiMax™.
INTENDED USE
This Dremel Multi-Max™ Tool is intended for dry sanding of surfaces, corners, edges, scraping, sawing soft metals, wood and plastic components, and grout removal using the applicable tools and accessories recommended by Dremel.
Operating Instructions
LEARNING TO USE THE TOOL
Getting the most out of your oscillating tool is a FIG. 6 matter of learning how to let the speed and the
feel of the tool in your hands work for you.
The first step in learning to use the tool is to get the “feel” of it. Hold it in your hand and feel its weight and balance (Fig. 6). Depending on the application, you will need to adjust your hand position to achieve optimum comfort and control. The unique comfort grip on the body of the tool allows for added comfort and control during use.
When holding tool, do not cover the air vents with your hand. Blocking the air vents could cause the motor to overheat.
-9-
DM 2610031482 05-13_MM30 5/28/13 8:11 AM Page 10
IMPORTANT! Practice on scrap material first to see how the tool’s high-speed action performs. Keep in mind that your tool will perform best by allowing the speed, along with the correct accessory, do the work for you. Be careful not to apply too much pressure.
Instead, lower the oscillating accessory lightly to the work surface and allow it to touch the point at which you want to begin. Concentrate on guiding the tool over the work using very little pressure from your hand. Allow the accessory to do the work.
Usually it is better to make a series of passes with the tool rather than to do the entire job with one pass. To make a cut, for example, pass the tool back and forth over the work. Cut a little material on each pass until you reach the desired depth.
SLIDE "ON/OFF" SWITCH
The tool is switched "ON" by the slide switch located on the topside of the motor housing.
TO TURN THE TOOL "ON", slide the switch button forward.
TO TURN THE TOOL "OFF", slide the switch button backward.
FIG. 7
Variable Speed
Control Dial
VARIABLE SPEED CONTROL DIAL
This tool is equipped with a variable speed control dial (Fig. 7). The speed may be controlled during operation by presetting the dial in any one of ten positions.
OPERATING SPEEDS
The Dremel Multi-Max™ consists of an AC universal motor and oscillating mechanism to perform applications such as cutting, grout removal, scraping, sanding and more.
The Dremel Multi-Max™ has a high oscillating motion of 10,000 - 23,000 /min (OPM). The high speed motion allows the Dremel Multi-Max™ to achieve with excellent results. The oscillating motion allows the dust to fall to the surface rather than slinging particles into the air.
To achieve the best results when working with different materials, set the variable speed control to suit the job (See Speed Chart on Page 12 & 13 for guidance) . To select the right speed for the accessory in use, practice with scrap material first.
NOTE: Speed is affected by voltages changes. A reduced incoming voltage will slow the OPM of the tool, especially at the lowest setting. If your tool appears to be running slowly, increase the speed setting accordingly. The tool may not start at the lowest switch setting in areas where outlet voltage is less than 120 volts. Simply move the speed setting to a higher position to begin operation.
The variable speed control settings are marked on the speed control dial. The settings for approximate /min (OPM) are:
Switch Setting |
Speed Range |
|
/min (OPM) |
2 |
10,000-11,000 |
4 |
11,000-13,000 |
6 |
13,000-16,000 |
8 |
16,000-19,000 |
10 |
19,000-23,000 |
You can refer to the charts on the following pages to determine the proper speed, based on the material and accessory being used. These charts enable you to select both the correct accessory and the optimum speed at a glance.
-10-
DM 2610031482 05-13_MM30 5/28/13 8:11 AM Page 11
Please refer to figures 8 and 9 for further instruction on how to use your Dremel Multi-Max™. Following these instructions will allow you to get the highest performance out of your oscilating tool.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FIG. 8 |
|
|
|
|
|
FIG. 9 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CORRECT: Sand with a smooth back and forth motion, allowing the weight of the tool to do the work.
INCORRECT: Avoid sanding with only the tip of the pad. Keep as much sand paper in touch with the work surface as possible.
CORRECT: Always sand with the pad and sandpaper flat against the work surface. Work smoothly in a back and forth motion.
INCORRECT: Avoid tipping the pad. Always sand flat.
CORRECT: Always cut with a smooth back and forth motion. Never force the blade. Apply light pressure to guide the tool.
INCORRECT: Do not twist the tool while cutting.This can cause the blade to bind.
CORRECT: Make sure flexible scraper blade flexes enough
INCORRECT: Avoid screw head touching surface with flexible scraper blade.
-11-
WOOD
-12-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
in ¼ |
½ |
¾ |
1 |
|
|
|
|
|
|
|
|
|
1¼ |
1½ |
|
|
|
|
|
||||
CARBIDE
mm |
10 |
20 |
30 |
40 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Multi-Max™ Accessory Speed Settings |
Use only Dremel, high-performance accessories. |
|
|
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
" |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
! |
|
|
|
|
(! +&- |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*"+ +" ))! |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(! +&- |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*"+ &(- |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
))! '.,% |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
.-' !" |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
/ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
))! '.,% |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
.-' !" |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
/ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
))! '.,% |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
.-' !" |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
/ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
& ))! "-' |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
'.,% .-' !" |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
/ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
& ))! "-' |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
' !" |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
/ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
+ &!" '.,% .- |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
' !" |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
.'-& (" |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
12 Page AM 8:11 5/28/13 MM30_13-05 2610031482 DM
"
JAB SAW
DRYWALL
WOO
BiM SAW BLADE
WOOD & METAL
-13-
Multi-Max™ Accessory Speed Settings |
Use only Dremel, high-performance accessories. |
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
# |
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||
|
|
|
#" |
|
|
|
|
|
|
|
|
|
|
|
|
! |
|
|
|
)0.$$. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
,$+#$ / |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
$+ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
.$ |
|
|
|
|
|
|
|
|
|||||||||||
#$,*" ,+$ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
)',+ %'- $ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
$ |
|
|
|
|
|
|
|
|
|||||||||||
)',+ %'- $ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
$ |
|
|
|
|
|
|
|
|
|||||||||||
#!# ) ( )$ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
$ /#$ ) ( ) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
$ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
)#+ # %'& |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
( ) |
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
)#+ ) # |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*( |
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
13 Page AM 8:11 5/28/13 MM30_13-05 2610031482 DM
#
DM 2610031482 05-13_MM30 5/28/13 8:11 AM Page 14
Operating Applications
APPLICATION
Your Dremel Multi-Max™ Tool is intended for sanding and cutting wooden materials, plastic, plaster and non-ferrous metals. It is especially suitable for working close to edges, in tight spaces, and for flush cutting. This tool must be used only with Dremel accessories .
Below are some typical uses for your Dremel Multi-Max™ Tool.
! WARNING For all accessories, work with the accessory away
from the body. Never position hand near or directly in front of working area. Always hold the tool with both hands and wear protective gloves.
Flush Cutting
Remove excess wood from door jamb, window sill and/or toekick. Removing excess copper or PVC pipe.
Removal work
e.g. carpets & backing, old tile adhesives, caulking on masonry, wood and other surfaces.
Removal of excess materials
e.g. plaster, mortar splatters, concrete on tiles, sills.
Preparation of surfaces e.g. for new floors and tiles.
Detail sanding
e.g. for sanding in extremely tight areas otherwise difficult to reach and require hand sanding
CUTTING
Saw blades are ideal for making precise cuts in tight areas, close to edges or flush to a surface.
Select a medium to high speed for making initial plunge, start off at medium speed for increased control. After making your initial cut, you can increase speed for faster cutting ability.
Flush cutting blades are intended to make precise cuts to allow for installation of flooring or wall material. When flush cutting
it is important not to force the tool during the plunge cut. If you experience a strong vibration in your hand during the plunge cut, this indicates that you are applying too much pressure. Back the tool out and let the speed of the tool do the work. While keeping the teeth
of the blade in the work surface, move the back of the tool in a slow sideways motion. This motion will help expedite the cut.
When making a flush cut it is always a good idea to have a piece of scrap material (tile or wood) supporting the blade. If you need to rest the flush cutting blade on a delicate surface, you should protect the surface with cardboard or masking tape.
The flat saw blade is ideal for 
making precise cuts in wood, plaster, drywall material.
Applications include cutting openings in flooring for venting, repairing damaged flooring, cutting openings for electrical boxes. The blade works best on softer woods such as pine. For harder woods, the blade life will be limited.
Select a medium to high speed.
The flat saw blade can also be used for window restoration making glazing easy to remove. The saw blade can be placed directly against the edge of the window frame, guiding the blade through the glazing.
GROUT REMOVAL
Grout removal blades are ideal
for removing damaged or 
cracked grout. Grout blades come in different widths (1/16" and 1/8") to
tackle different grout line widths. Before selecting a grout blade measure the grout line width to pick the appropriate blade.
Select a medium to high speed.
To remove the grout, use a back and forth motion, making several passes along the grout line. The hardness of the grout will dictate how many passes are needed. Try and keep the grout blade aligned with the grout line and be careful not to apply too much side pressure on the grout blade during the process. To control plunge depth use the carbide grit line on the blade as an indicator. Be careful not to plunge beyond the carbide grit line to avoid damage to the backer board material.
The grout blades can handle both sanded and unsanded grout. If you notice the blade clogging during the grout removal process, you can use a brass brush to clean the grit, thus exposing the grit again.
The grout blade geometry is designed so that the blade can remove all grout up to the surface of a wall or corner. This can be
-14-
DM 2610031482 05-13_MM30 5/28/13 8:11 AM Page 15
accomplished by ensuring that the segmented portion of the blade is facing the wall or corner.
SCRAPING
Scrapers are suitable for removing old coats of varnish or adhesives, removing bonded carpeting, e.g. on stairs/steps and other small/medium size surfaces.
Select low to medium speed.
Rigid scrapers are for large area
removal, and harder materials such as vinyl flooring, carpeting and tile adhesives. When
removing strong, tacky adhesives, grease the scraper blade surface with (petroleum jelly or silicone grease) to reduce gumming up.
The carpet/vinyl flooring removes easier if it is scored prior to removal so the scraper blade can move underneath the flooring material.
Flexible scrapers are used for hard to reach areas and softer material such as caulk.
Mount the scraper blade with the logo side facing up. With the flexible scraper, make sure that the screw head does not make contact with surface during the scraping process (a 30 - 45 degree pitch is recommend). This can be accomplished by making sure that the tool is at an angle to the blade. You should be able to see the blade flex during the scraping process.
If you are removing caulk from a delicate surface such as a bath tub or tile back splash, we recommend taping or protecting the surface that the blade will rest on. Use rubbing alcohol to clean the surface after the caulk and/or adhesive is removed.
Turn the tool on and place desired accessory on the area where material is to be removed.
Begin with light pressure. The oscillating motion of accessory only occurs when pressure is applied to the material to be removed.
Excessive pressure can gouge or damage the background surfaces (e.g,. wood, plaster).
SANDING
Sanding accessories are suitable for dry sanding of wood, metal, surfaces, corners and edges and
hard to reach areas.
Work with the complete surface of the sanding pad, not only with the tip.
Corners may be finished using the tip or edge of the selected accessory, which should occasionally be rotated during use to distribute the wear on the accessory and backing pad surface.
Sand with a continuous motion and light pressure. DO NOT apply excessive pressure - let the tool do the work. Excessive pressure will result in poor handling, vibration, and unwanted sanding marks and premature wear on the sanding sheet.
Always be certain that smaller workpieces are securely fastened to a bench or other support. Larger panels may be held in place by hand on a bench or sawhorses.
Open-coat aluminum oxide sanding sheets are recommended for most wood or metal sanding applications, as this synthetic material cuts quickly and wears well. Some applications, such as metal finishing or cleaning, require special abrasive pads which are available from your dealer. For best results, use Dremel sanding accessories which are of superior quality and are carefully selected to produce professional quality results with your oscillating tool.
The following suggestions may be used as a general guide for abrasive selection, but the best results will be obtained by sanding a test sample of the workpiece first.
Grit |
Application |
Coarse |
For rough wood or metal |
|
sanding, and rust or old |
|
finish removal. |
Medium |
For general wood or metal |
|
sanding |
Fine |
For final finishing of wood, |
|
metal, plaster and other |
|
surfaces. |
With the workpiece firmly secured, turn tool on as described above. Contact the work with the tool after the tool has reached its full speed, and remove it from the work before switching the tool off. Operating your oscillating tool in this manner will prolong switch and motor life, and greatly increase the quality of your work.
Move the oscillating tool in long steady strokes parallel to the grain using some lateral motion to overlap the strokes by as much as 75%. DO NOT apply excessive pressure - let the tool do the work. Excessive pressure will result in poor handling, vibration, and unwanted sanding marks.
-15-
DM 2610031482 05-13_MM30 5/28/13 8:11 AM Page 16
GRINDING
The diamond paper accessory
allows for the Multi-Max™ to be 
used for grinding away cement, plaster or thin set. Preparing the surface for tile
replacement is a common application for this accessory.
The diamond paper needs to be mounted to the backing pad prior to use.
Select a low to high speed depending on the material removal rate desired.
The carbide rasp accessory also 
allows the Multi-Max™ to grind away cement, thinset mortar, plaster, and also wood. This accessory is
commonly used to prepare for tile replacement or rasping wood to smooth a surface or remove material.
The speed should be set at high speed for aggressive material removal or at low speed for a more detailed removal of material.
Do not apply excessive pressure on the tool-let it do the work.
Corners may be finished using the tip or edge of the selected accessory, which should occasionally be rotated during use to distribute the wear on the accessory and backing pad surface.
Grind with a continuous motion and light pressure. DO NOT apply excessive pressure - let the tool do the work. Excessive pressure will result in poor handling, vibration, and premature wear on the diamond paper sheet.
Selecting Sanding/Grinding Sheets
Material |
Application |
Grit Size |
|
All wooden materials (e.g., |
For coarse-sanding, e.g. of |
Coarse |
60 |
hardwood, softwood, chipboard, |
rough, unplanned beams and |
|
|
building board) Metal materials– |
boards |
|
|
Metal materials, fiberglass |
For face sanding and planing |
Medium |
120 |
and plastics |
small irregularities |
|
|
|
For finish and fine sanding of |
Fine |
240 |
Sand Paper (Dark) |
wood |
|
|
Paint, varnish, filling compound |
For sanding off paint |
Coarse |
80 |
and filler |
|
|
|
|
For sanding primer (e.g., for |
Medium |
120 |
|
removing brush dashes, drops |
|
|
|
of paint and paint run) |
|
|
Sand Paper (White) |
For final sanding of primers |
Fine |
240 |
|
|||
|
before coating |
|
|
Masonry, stone, cement |
For smoothing, shaping and |
Coarse |
60 |
and thin set |
braking edges |
|
|
Diamond Paper |
|
|
|
-16-
Loading...