Denon DVD-3910 User Manual

DVD AUDIO-VIDEO/SUPER AUDIO CD PLAYER

DVD-3910

OPERATING INSTRUCTIONS

OPEN/CLOSE	PLAY	STOP
	STILL / PAUSE
ON / STANDBY		VIDEO MODE
	HDMI / DVI	SUPER	PURE
	SELECT FORMAT	AUDIO CD	DIRECT
		SETUP	SELECT
DENON LINK AL 24 PLUS
		PUSH ENTER

DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER DVD-3910

POWER OFF				POWER ON
HDMI/DVI		NTSC/PAL		OPEN/
SELECT	FORMAT			CLOSE
				CD/STEREO
				/MULTI
				PROG/DIR
				CLEAR
		SEARCH MODE		CALL
BACK LIGHT	ANGLE	SUBTITLE		AUDIO
TOP MENU				DISPLAY
MENU				RETURN
STOP	STILL/PAUSE		PLAY
SKIP			SLOW/SEARCH
REPEAT	A-B		PAGE
RANDOM	MARKER	ZOOM		DIMMER
SETUP	PICT ADJ.		PURE DIRECT
		MEMORY		SELECT

RC-972

FOR ENGLISH READERS

PAGE 006 ~ PAGE 081

IMPORTANT TO SAFETY

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

1.Handle the power supply cord carefully

Do not damage or deform the power supply cord. If it is damaged or deformed, it may cause electric shock or malfunction when used. When removing from wall outlet, be sure to remove by holding the plug attachment and not by pulling the cord.

2.Do not open the top cover

In order to prevent electric shock, do not open the top cover. If problems occur, contact your DENON DEALER.

3.Do not place anything inside

Do not place metal objects or spill liquid inside the DVD audio-video/ Super audio CD player.

Electric shock or malfunction may result.

Please, record and retain the Model name and serial number of your set

shown on the rating label.
Model No. DVD-3910	Serial No.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

NOTE:

This DVD audio-video/Super audio CD player uses the semiconductor laser. To allow you to enjoy music at a stable operation, it is recommended to use this in a room of 5 °C (41 °F) ~ 35 °C (95 °F).

CAUTION:

USE OF CONTROLS OR ADJUSTMENTS OR REFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

THE COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL.

FCC INFORMATION (For US customers)

1. PRODUCT

This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this product may not cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired operation.

2.IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modification not expressly approved by DENON may void your authority, granted by the FCC, to use the product.

3.NOTE

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the product into an outlet on a circuit different from that to which the receiver is connected.

•Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for help.

•FOR CANADA MODEL ONLY

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• POUR LES MODELE CANADIENS UNIQUEMENT

ATTENTION

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA

LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’ AU FOND.

2

ENGLISH FRANCAIS ESPAÑOL

FRONT PANEL

PANNEAU AVANT

PANEL FRONTAL

!3!4	!5	!6!7!8!9@0@1@2
		OPEN/CLOSE	PLAY STOP
			STILL / PAUSE

ON / STANDBY	VIDEO MODE
HDMI / DVI	SUPER	PURE
SELECT FORMAT	AUDIO CD	DIRECT
	SETUP	SELECT

	DENON LINK	AL 24 PLUS
					PUSH ENTER
					DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER DVD-3910
	t				o !1
qw e	r		y	u	i !0 !2

REAR PANEL

PANNEAU ARRIERE

PANEL TRASERO

@3

@4

@5

@7@9#1
@6 @8#0#2	#3#4	#5#6#7

3

SAFETY INSTRUCTIONS

1.Read Instructions – All the safety and operating instructions should be read before the product is operated.

2.Retain Instructions – The safety and operating instructions should be retained for future reference.

3.Heed Warnings – All warnings on the product and in the operating instructions should be adhered to.

4.Follow Instructions – All operating and use instructions should be followed.

5.Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

6.Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7.Water and Moisture – Do not use this product near water – for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8.Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table

recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a

mounting accessory recommended by the manufacturer.

9.A product and cart combination should be moved with care. Quick stops, excessive force,

and uneven surfaces may cause the product and cart combination to overturn.

10.Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11.Power Sources – This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12.Grounding or Polarization – This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL

ELECTRICAL CODE ANTENNA

LEAD IN

WIRE

GROUND

CLAMP

ANTENNA DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRIC

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC - NATIONAL ELECTRICAL CODE

13.Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

15.Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A.

16.Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

17.Power Lines – An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

18.Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

19.Object and Liquid Entry – Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

20.Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

21.Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a)When the power-supply cord or plug is damaged,

b)If liquid has been spilled, or objects have fallen into the product,

c)If the product has been exposed to rain or water,

d)If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation,

e)If the product has been dropped or damaged in any way, and

f)When the product exhibits a distinct change in performance

– this indicates a need for service.

22.Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

23.Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

24.Wall or Ceiling Mounting – The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

25.Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

4

ESPAÑOL FRANCAIS ENGLISH

NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION / NOTAS SOBRE EL USO

•Avoid high temperatures.

Allow for sufficient heat dispersion when installed on a rack.

•Eviter des températures élevées.

Tenir compte d’une dispersion de chaleur suffisante lors de l’installation sur une étagère.

•Evite altas temperaturas.

Permite la suficiente dispersión del calor cuando está instalado en la consola.

•Handle the power cord carefully.

Hold the plug when unplugging the cord.

•Manipuler le cordon d’alimentation avec précaution.

Tenir la prise lors du débranchement du cordon.

•Maneje el cordón de energía con cuidado. Sostenga el enchufe cuando desconecte el cordón de energía.

•Keep the set free from moisture, water, and dust.

•Protéger l’appareil contre l’humidité, l’eau et lapoussière.

•Mantenga el equipo libre de humedad, agua y polvo.

•Unplug the power cord when not using the set for long periods of time.

•Débrancher le cordon d’alimentation lorsque l’appareil n’est pas utilisé pendant de longues périodes.

•Desconecte el cordón de energía cuando no utilice el equipo por mucho tiempo.

(For sets with ventilation holes)

•Do not obstruct the ventilation holes.

•Ne pas obstruer les trous d’aération.

•No obstruya los orificios de ventilación.

•Do not let foreign objects in the set.

•Ne pas laisser des objets étrangers dans l’appareil.

•No deje objetos extraños dentro del equipo.

•Do not let insecticides, benzene, and thinner come in contact with the set.

•Ne pas mettre en contact des insecticides, du benzène et un diluant avec l’appareil.

•No permita el contacto de insecticidas, gasolina y diluyentes con el equipo.

•Never disassemble or modify the set in any way.

•Ne jamais démonter ou modifier l’appareil d’une manière ou d’une autre.

•Nunca desarme o modifique el equipo de ninguna manera.

Copyrights / Droits d’auteur / Derechos de Autor

2 It is prohibited by law to reproduce,	2 La reproduction, la diffusion, la
broadcast, rent or play discs in public	location, le prêt ou la lecture publique
without the consent of the copyright	de ces disques sont interdits sans le
holder.	consentement	du détenteur des
	droits d’auteur.

2De acuerdo con las leyes está prohibido reproducir, emitir, alquilar o interpretar discos en público sin la autorización del propietario de los derechos de autor.

5

ENGLISH

— TABLE OF CONTENTS —

z Features...................................................................................	6, 7
x Discs ............................................................................................	8
c Cautions on Handling Discs.........................................................	9
v Connections ......................................................................	10 ~ 20
b Part Names and Functions ..................................................	21, 22
n Remote Control Unit............................................................	23, 24
m Loading Discs ............................................................................	25
, Changing the Default Settings ..........................................	26 ~ 47
. Using the Pure Direct Mode................................................	47, 48
⁄0Using the Super Audio CD Setup ..............................................	48
⁄1Adjusting the Picture Quality ............................................	49 ~ 52
⁄2Using the Video Setup ......................................................	53 ~ 55
⁄3Playback ............................................................................	56 ~ 60

⁄4Playing Repeatedly ..............................................................	61, 62
⁄5Playing Tracks in the Desired Order ..........................................	63
⁄6Playing Tracks in the Random Order .........................................	64
⁄7Using the On-screen Display .....................................................	65
⁄8Using the Multiple Audio, Subtitle and Angle Functions.......	66 ~ 68
⁄9Using the Menus .................................................................	69, 70
¤0Marking Scenes you want to see again ....................................	71
¤1Playing in the Zoom Mode ........................................................	72
¤2Playing MP3.........................................................................	73, 74
¤3Playing WMA .............................................................................	75
¤4Playing Still Picture Files (JPEG format)............................	76 ~ 78
¤5Troubleshooting ...................................................................	79, 80
¤6Main Specifications....................................................................	81

• ACCESSORIES

Please check to make sure the following items are included with the main unit in the carton:

q Audio video cord.......................................................................	1
w Remote control unit (RC-972)...................................................	1
e R6P/AA batteries ......................................................................	2
r Power supply cord....................................................................	1

t DENON LINK cord....................................................................	1
y IEEE 1394 cord.........................................................................	1
u Operating instructions ..............................................................	1
i Service station list ....................................................................	1

q

w

e

		RC-972
r	t	y

1FEATURES

1.Digital transfer connectors

The DVD-3910 can be connected to another digital transfer compatible Denon component (AV amplifier, etc.) using a single cable (included) for high quality digital sound with little transfer loss.

(1)Denon Link terminal

This terminal can be used for digital transfer of not only DVD video signals, but also multi-channel audio signals of DVD audio.

(2)IEEE 1394 terminal

This terminal can be used for digital transfer of not only DVD video signals, but also DVD audio signals, Super Audio CD signals and other multi-channel audio signals.

Digital transfer of video signals is possible by connecting an HDCP compatible display device equipped with one of the connectors below using a special cable.

When playing DVD AUDIO with CPPM, the video signal cannot be output, and then the audio signal cannot be output from the HDMI connector too.

(3)HDMI connector

Digital video signals are transferred in color space (Y/Cb/Cr) or RGB.

The audio signals can be transferred simultaneously, so both audio and video signals can be transferred with a single cable.

(4)DVI-D connector

Digital video signals are transferred in RGB.

6

2.Super Audio CD multi-channel playback compatibility

In addition to playing DVD audio and video discs, the DVD3910 can play multi-channel Super Audio CDs with a playback frequency range covering 100 kHz and a dynamic range of 120 dB or greater within the audible frequency range, and a maximum of 5.1 channels can be output.

3.AL24 Processing Plus at all channel

AL24 Processing Plus compensates the input digital data to reproduce the sound with analog waveforms as close as possible to those existing in nature and with 24-bit quality. The result is increased musical reproduction capabilities of reverberations, etc., at low levels, for a sound that seems to draw you into the concert hall.

Equipped for not only the left and right channels but also for the front left and right, the surround left and right, center and subwoofer channels.

4.High precision 24-bit D/A converter

The audio playback circuit includes an advanced segment type D/A converter with the high technical specifications in the business, manufactured by Burr-Brown, a company with an established reputation for D/A converters. This high performance D/A converter allows not only input of the 24bit/192 kHz data of DVD-Audio discs, it also includes an analog pure FIR filter for ideal DSD playback of Super Audio CDs. Furthermore, the same DAC is used unsparingly for the front, the surround, center and LFE channels to provide optimum sound quality during multi-channel playback as well.

5.HDCD® (High Definition Compatible Digital®) decoder (NOTE 1)

HDCD is an encoding/decoding technology that greatly reduces the distortion occurring at the time of digital recording while maintaining compatibility with the conventional CD format. HDCD allows 20-bit data to be converted into the 16bit data of current CDs with no loss in sound quality.

The use of this HDCD decoder makes it possible to achieve the high resolution and low distortion characteristic of HDCD when playing HDCD-compatible discs, and DENON’s digital technology optimizes the high sound quality possibilities of HDCD technology. Furthermore, normal CDs and HDCDcompatible CDs are automatically identified, and the optimum digital signal processing for that type of disc is used.

6.Dolby Digital/DTS decoder (NOTE 2, 3)

The DVD-3910 is equipped with a built-in Dolby Digital/DTS decoder, allowing you to recreate the atmosphere of a movie theater or concert hall when using the DVD-3910 in combination with an AV amplifier and speakers.

7.Progressive Scan circuit “DCDiTM” (NOTE 4)

The DVD-3910 is equipped with a high precision Progressive Scan circuit “DCDi™” allowing it to reproduce movies and other images on DVDs with a quality near that of the original.

8.Newly developed video processing circuit

The differences in brightness and color level between adjacent picture elements in the horizontal, vertical and diagonal directions are detected to adjust the contours. The brightness signal and color signal are processed separately, resulting in natural, clear images.

9.12-bit/216 MHz video D/A converter (NOTE 5)

The DVD-3910 uses a video D/A converter that conducts D/A conversion of all video signals at 12 bits and allows 8X oversampling in the progressive mode to achieve the high quality picture that DVDs are meant to provide. In addition, NSV technology reduces noise upon D/A conversion.

ENGLISH

10.Thorough vibration-resistant design

(1)Mechanism using a hybrid loader.

(2)The pickup mechanism is positioned at the center to reduce the effects of external vibrations.

(3)A heavyweight chassis and low center of gravity make for a low vibration design.

11.Multiple functions

(1)Still picture playback function

Kodak Picture CD (NOTE 6) and Fujifilm Fujicolor CD (NOTE 7) can be played on the DVD-3910.

Still images stored in JPEG format on CD-R/RWs can also be played.

(2)Windows Media™ playback function (NOTE 8) Windows Media™ CDs can be played on the DVD-3910.

(3)Multiple audio function

Selection of up to 8 audio languages.

(The number of languages offered differs from DVD to DVD.)

(4)Multiple subtitle function

Selection of up to 32 subtitle languages.

(The number of languages offered differs from DVD to DVD.)

(5)Multiple angle function

The angle of view can be changed.

(For DVDs on which multiple angles are recorded.)

(6)GUI (Graphical User Interface) function

The DISPLAY button on the remote control unit can be used to display player and disc information on the TV screen.

(7)Marker function

The positions of up to five scenes can be stored in the memory, so you can watch your favourite scenes whenever you want.

(8)Playback disable function

This function can be used to disable playback of DVDs you do not want children to watch.

NOTES:

1. ®, HDCD®, High Definition Compatible Digital® and Microsoft® are either registered trademarks or trademarks of

Microsoft Corporation, Inc. in the United States and/or other countries. HDCD system manufactured under license from Microsoft Corporation, Inc. This product is covered by one or more of the following: In the USA: 5,479,168, 5,638,074, 5,640,161, 5,808,574, 5,838,274, 5,854,600, 5,864,311, 5,872,531, and in Australia: 669114. Other patents pending.

2.Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

3.“DTS” and ”DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc.

4.“DCDi™” is trademark of Faroodja, a division of Genesis Microchip Inc.

5.“NSV” is a trademark of Analog Devices, Inc.

6.“KODAK” is a trademark of Eastman Kodak Company.

7.“FUJICOLOR CD” is a trademark of Fuji Photo Film Co, Ltd.

8.“Windows Media™”, “Windows™”are a trademarks of Microsoft Corporation, Inc.

7

ENGLISH

2DISCS

•The types of discs listed on the table below can be used on the DVD-3910. The marks are indicated on the disc labels or jackets.

Usable			Mark (logo)		Recorded	Disc size
discs					signals
DVD video						12 cm
DVD audio
(NOTE 1)					Digital audio +
DVD-R			R		digital video
					(MPEG2)
	R
DVD-RW						8 cm
(NOTE 2)			R W
	R W
Super					Digital audio	12 cm
audio CD
Video CD					Digital audio +	12 cm
					digital video
(NOTE 1)						8 cm
					(MPEG1)
CD					Digital audio	12 cm
					MP3
CD-R
CD-RW			Recordable	ReWritable	Digital picture
(NOTE 3)						8 cm
					(JPEG)
Picture CD					JPEG	12 cm
Fujicolor					JPEG	12 cm
CD
WMA
(Windows					Digital audio	12 cm
Media
Audio)

2The following types of discs cannot be played on the DVD-3910:

•DVDs with region numbers other than “1” or “ALL”

•DVD-ROM/RAMs

•CD-ROMs (unless MP3, JPEG, WMA Files)

•CVD/VSDs

•CDVs (Only the audio part can be played.)

•CD-Gs (Only the audio is output.)

•Photo CDs

NOTE 1: Some DVD audio, DVD video and video CD discs do not operate as described in this manual due to the intentions of the discs’ producers.

NOTE 2: Playing DVD-R and DVD-RW discs

DVD-R and DVD-RW discs recorded in video format on a DVD recorder can be played on the DVD-3910.

Discs that have not be finalized cannot be played. Depending on the disc’s recording status, the disc may not be accepted or may not be played normally (the picture or sound may be not be smooth, etc.).

NOTE 3: According to recording quality, some CD-R/RW cannot be played.

NOTE:

• This DVD player is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc.

If the Region number described on the

DVD disc does not correspond to the 1 Region number of this DVD player, this

DVD player cannot play this disc.

The Region number for this DVD player is 1.

2Disc terminology

•Groups and tracks (DVD-audios)

DVD-audios are divided into several large sections called “groups” and smaller sections called “tracks”.

Numbers are allotted to these sections. These numbers are called “group numbers” and “track numbers”.

For example:

Group 1

Group 2

Track 1

Track 2

Track 3

Track 1

Track 2

•Titles and chapters (DVD-videos)

DVD-videos are divided into several large sections called “titles” and smaller sections called “chapters”.

Numbers are allotted to these sections. These numbers are called “title numbers” and “chapter numbers”.

For example:

			Title 1					Title 2
Chapter 1		Chapter 2			Chapter 3			Chapter 1		Chapter 2

•Tracks (Super audio CDs, video and music CDs)

Super audio CDs, video and music CDs are divided into sections called “tracks”.

Numbers are allotted to these sections. These numbers are called “track numbers”.

For example:

Track 1

Track 2

Track 3

Track 4

Track 5

•Playback control (video CDs)

Video CDs including the words “playback control” on the disc or jacket are equipped with a function for displaying menus on the TV screen for selecting the desired position, displaying information, etc., in dialog fashion.

In this manual, playing video CDs using such menus is referred to “menu playback”.

Video CDs with playback control can be used on the DVD3910.

8

3 CAUTIONS ON HANDLING DISCS

Discs

Only the discs including the marks shown on page 8 can be played on the DVD-3910.

Note, however, that discs with special shapes (heart-shaped discs, hexagonal discs, etc.) cannot be played on the DVD-3910. Do not attempt to play such discs, as they may damage the player.

Holding Discs

Avoid touching the surface of discs when loading and unloading them.

Be careful not to get fingerprints on the signal surface (the side which shines in rainbow colors).

ENGLISH

Cautions on Handling Discs

•Do not get fingerprints, grease or dirt on discs.

•Be especially careful not to scratch discs when removing them from their cases.

•Do not bend discs.

•Do not heat discs.

•Do not enlarge the center hole.

•Do not write on the labeled (printed) side with a ball-point pen or a pencil.

•Water droplets may form on the surface if the disc is moved suddenly from a cold place to a warm one. Do not use a hairdryer, etc., to dry the disc.

Cautions on Storing Discs

•Always eject discs after playing them.

•Keep discs in their cases to protect them from dust, scratches and warping.

•Do not put discs in the following places:

1.Places exposed to direct sunlight for long periods of time

2.Humid or dusty places

3.Places exposed to heat from heaters, etc.

Cleaning Discs

2Fingerprints or dirt on the disc may lower sound and picture quality or cause breaks in playback. Wipe off fingerprints or dirt.

2Use a commercially available disc cleaning set or a soft cloth to wipe off fingerprints or dirt.

Wipe gently from the middle	Do not wipe with a circular
outwards.	motion.

NOTE:

•Do not use record spray or antistatic. Also do not use volatile chemicals such as benzene or thinner.

Record Thinner Benzene

spray

Cautions on Loading Discs

•Only load one disc at a time. Loading one disc on top of another may result in damage or scratch the discs.

•Load 8 cm discs securely in the disc guide, without using an adapter. If the disc is not properly loaded, it may slip out of the guide and block the disc tray.

•Be careful not to let your fingers get caught when the disc tray is closing.

•Do not place anything but discs in the disc tray.

•Do not load cracked or warped discs or discs that have been fixed with adhesive, etc.

•Do not use discs on which the adhesive part of cellophane tape or glue used to attach the label is exposed, or discs with traces of tape or labels that have been peeled off. Such discs may get stuck inside the player, resulting in damage.

CAUTIONS ON INSTALLATION

For heat dispersal, leave at least 10 cm of space between the top, back and sides of this unit and the wall or other components.

10 cm or more

10 cm or more

wall

9

ENGLISH

4 CONNECTIONS

NOTES:

•Read the manuals of all the components when making connections.

•Keep the power supply cord unplugged until all connections have been completed.

•If the power is on when connections are made, noise may be generated and damage the speakers.

•Be sure to connect the left and right channels properly, L (left) to L, R (right) to R.

•Plug the power supply cord securely into the power outlet. Incomplete connection may result in noise.

•Binding the power supply cord together with connection cords may result in humming or noise.

(1) Connecting to a TV

•Use the included audio video cord to connect the TV’s video input connector and audio input connectors to the DVD-3910’s VIDEO OUT or S-VIDEO OUT and AUDIO OUT.

S-Video output connector

The video signals are divided into color (C) and brightness (Y) signals, achieving a clearer picture.

If the TV is equipped with an S-Video input connector, we recommend connecting it to the DVD-3910’s S-Video output connector using a commercially available S-Video

connection cord.

DVD-3910

To power outlet

L	R
AUDIO IN		VIDEO IN	S-VIDEO IN

TV

NOTES:

•Connect the DVD-3910’s video outputs to the TV either directly or through an AV amplifier. Do not connect it via a VCR (video cassette recorder). Some discs contain copy prohibit signals. If such discs are played via a VCR, the copy prohibit system may cause disturbance in the picture.

•Set the “TV TYPE” in “VIDEO SETUP” in “SETUP” to comply with your TV’s video format. When the TV is NTSC formatted set to NTSC. (See pages 36, 37.)

•To use with 5.1ch audio output, set “2CH (SRS OFF)” or “2CH (SRS ON)” under “AUDIO CHANNEL” in “AUDIO SETUP” on the “SETUP” menu to the initial settings.

(See page 38.)

•Set the “TV ASPECT” in “VIDEO SETUP” in “SETUP” to comply with your TV’s aspect. (See page 36.)

•To use with video out or s-video output, set “INTERLACED” in “VIDEO OUT” in “VIDEO SETUP” in “SETUP” at the initial settings. (See pages 36, 37.)

10

ENGLISH

(2) Connecting to a TV or Monitor Equipped with Color Component Input Connectors

Color component output connectors (PR/CR, PB/CB and Y)

The red (PR/CR), blue (PB/CB) and brightness (Y) signals are output independently, achieving more faithful reproduction of the colors.

•The color component input connectors may be marked differently on some TVs or monitors (PR, PB and Y/R- Y, B-Y and Y/CR, CB and Y, etc.). For details, refer to the TV’s operating instructions.

•Connect in this way if your TV is compatible with Progressive Scan.

DVD-3910

To power outlet

TV

L	R	PR/CR PB/CB Y
AUDIO IN		COMPONENT VIDEO IN

NOTES:

•Use the three commercially available video cords to connect the DVD-3910’s color component output connectors to the TV or monitor.

•Set the “TV TYPE” in “VIDEO SETUP” in “SETUP” to comply with your TV’s video format. When the TV is NTSC formatted set to NTSC. (See pages 36, 37.)

•Set the “VIDEO OUT” in “VIDEO SETUP” in “SETUP” to comply with Progressive TV.

•To use with 5.1ch audio output, set “2CH (SRS OFF)” or “2CH (SRS ON)” in “AUDIO CHANNEL” in “AUDIO SETUP” in “SETUP” at the initial settings. (See page 38.)

•Set the “TV ASPECT” in “VIDEO SETUP” in “SETUP” to comply with your TV’s aspect. (See page 36.)

CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE “STANDARD DEFINITION” OUTPUT.

11

ENGLISH

(3) Connecting to a AV amplifier with a built-in decoder

When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital or DTS bitstream signals are output from the DVD player’s digital audio output connectors. If a Dolby Digital or DTS decoder is connected, you can achieve sound with the power and sense of presence of a movie theater or concert hall.

DVD-3910

To power outlet

		Center speaker
Front speaker (left)			Front speaker (right)
75Ω/ohms pin-plug	(or)	Optical fiber cable
cable (commercially		(commercially
available)		available)
Digital audio input		Digital audio input	Subwoofer
connector (COAXIAL)		connector (OPTICAL)

Surround speaker (left)

Surround speaker (right)

AV amplifier with a built-in decoder (AV control center)

NOTES:

•Harsh noise that could harm your ears or damage the speakers is generated when a DVD recorded in DTS is played while using a decoder, etc., that is not DTS-compatible.

•When playing copyright-protected linear PCM or packed PCM DVDs, in consideration of copyrights, no digital signals are output for sources exceeding 48 kHz/16 bits. When playing such sources, either set “LPCM (44.1 kHz/48 kHz)” under “AUDIO SETUP” at “SETUP” to “ON” (see pages 38, 41.) or make analog connections. (See page 14.)

•When making digital connections to an AV amplifier that is not compatible with 96 kHz/88.2 kHz signals, set “LPCM (44.1 kHz/48 kHz)” under “AUDIO SETUP” at “SETUP” to “ON”. (See pages 38, 41.)

•With Super audio CDs, digital audio signals cannot be output from the digital out terminals. Use analog or IEEE1394 connections. (See pages 14, 17, 18.)

2 Connecting an optical fiber cable (commercially available) to the digital audio input connector (OPTICAL)

Line up in proper direction

Line up the cable in the proper directly, then insert it securely as far as it goes.

12

ENGLISH

2Sound output from the DVD-3910’s digital audio output connectors

In the case of bitstream output

		Settings
		DIGITAL OUT
	Audio recording format	NORMAL		PCM
	Dolby Digital	Dolby Digital bitstream		2 channels PCM
				(48 kHz / 16 bit)
DVD video
	DTS	DTS bitstream		2 channels PCM
				(48 kHz / 16 bit)

In the case of PCM output

					Settings
					LPCM SELECT
		Audio recording format			OFF	ON
				Copy protection ON	Copy protection OFF
	DVD video	Linear PCM	48 kHz / 16 ~ 24 bit	No output data (*1)	48 kHz / 16 ~ 24 bit PCM	48 kHz / 16 bit PCM
			96 kHz / 16 ~ 24 bit	No output data	96 kHz / 16 ~ 24 bit PCM	48 kHz / 16 bit PCM
			44.1 kHz / 16 ~ 24 bit	No output data (*2)	44.1 kHz / 16 ~ 24 bit PCM	44.1 kHz / 16 bit PCM
			48 kHz / 16 ~ 24 bit	No output data (*1)	48 kHz / 16 ~ 24 bit PCM	48 kHz / 16 bit PCM
		Linear PCM
	DVD audio		88.2 kHz / 16 ~ 24 bit	No output data	88.2 kHz / 16 ~ 24 bit PCM	44.1 kHz / 16 bit PCM
		or
			96 kHz / 16 ~ 24 bit	No output data	96 kHz / 16 ~ 24 bit PCM	48 kHz / 16 bit PCM
		Packed PCM
			176.4 kHz / 16 ~ 24 bit	No output data	88.2 kHz / 16 ~ 24 bit PCM	44.1 kHz / 16 bit PCM
			192 kHz / 16 ~ 24 bit	No output data	96 kHz / 16 ~ 24 bit PCM	48 kHz / 16 bit PCM
	Video CD		MPEG 1	44.1 kHz / 16 bit PCM		44.1 kHz / 16 bit PCM
	Music CD	44.1 kHz / 16 bit Linear PCM		44.1 kHz / 16 bit PCM		44.1 kHz / 16 bit PCM
	MP3 CD	MP3 (MPEG-1 Audio Layer 3)		44.1, 48 kHz / 16 bit PCM		44.1, 48 kHz / 16 bit PCM
	WMA CD	WMA (Windows Media Audio)		44.1, 48 kHz / 16 bit PCM		44.1, 48 kHz / 16 bit PCM
	Super audio CD	DSD (DIRECT STREAM DIGITAL)		No output data (*3)		No output data (*3)

*1 Only 48 kHz/16 bit sources are output.

*2 Only 44.1 kHz/16 bit sources are output.

*3 44.1 kHz/16-bit PCM signals are output during CD layer playback.

•Down-mixed to 2 channels for multi-channel PCM sources. (Only the front left and right channels are output for sources for which down-mixing is prohibited.)

•When “DIGITAL OUT : OFF” is selected at the PURE DIRECT MODE, digital signals are not output from the digital audio output at this time.

•Bitstream signals are signals that are compressed and converted into digital format. They are decoded into multi-channel audio signals (5.1-channels, etc.) by the decoder.

•Linear PCM audio is the signal recording format used for music CDs.

While the signals are recorded at 44.1 kHz/16 bit for music CDs, for DVDs they are recorded at 44.1 kHz/16 bit to 192 kHz/24 bit, providing higher sound quality than music CDs.

•Packed PCM signals are high sound quality compressed PCM signals that are decompressed with virtually no loss of data.

13

ENGLISH

(4) Connecting a basic 5.1-channel surround system

Analog 5.1-channel audio signals can be output from the DVD-3910.

The multichannel audio signals recorded in packed PCM and the multichannel Super audio CDs can be played when an AV amplifier equipped with analog 5.1-channel audio inputs is connected.

DVD-3910

To power outlet

			Center speaker
Front speaker (left)			Front speaker (right)
SURROUND	SUBWOOFER	CENTER	FRONT
			Subwoofer

Surround speaker (left)

Surround speaker (right)

AV amplifier with 5.1-channel input terminals

NOTES:

•For multi-channel connections, set “AUDIO CHANNEL” under “AUDIO SETUP” at “SETUP” to “MULTI CHANNEL” and make the “SPEAKER CONFIGURATION”, “CHANNEL LEVEL” and “DELAY TIME” settings. (See pages 38 ~ 42.)

•With the DVD-3910, we recommend turning the digital output off by using the PURE DIRECT MODE and only outputting analog signals in order to keep interference from the digital output circuitry to a minimum and allow you to enjoy high-quality multichannel sound thanks to the high-bit, high sampling frequency. (See pages 47, 48.)

14

ENGLISH

(5) Connecting to a Digital Recorder (MD Recorder, DAT Deck, etc.)

Set the “AUDIO SETUP” default setting as shown below. (See pages 38 ~ 41.)

• “DIGITAL OUT” → “PCM” “LPCM (44.1kHz/48kHz)” → “ON”

Playing DVDs with incorrect settings may result noise that could damage your ears or the speakers.

DVD-3910

B

	Digital audio	Digital audio
	input connector	input connector
Optical fiber cable (commercially available)	(OPTICAL)	(COAXIAL)
(or)

75Ω/ohms pin-plug cable (commercially available)

NOTE:

• Digital audio signals cannot be output when playing Super Audio CDs. Use analog connections to record Super Audio CDs.

(6) Connecting to a Stereo Component

DVD-3910

Stereo component

NOTE:

•When connecting to a 2-channel audio stereo device using the 5.1ch AUDIO OUT, set “AUDIO CHANNEL” under “AUDIO SETUP” on the “SETUP” to “2CH (SRS OFF)” or “2CH (SRS ON)” (see page 38.). For multi-channel sources, the signals are down-mixed into two channels (analog).

(Only the front left and right channels are output for sources for which down-mixing is prohibited.)

15

ENGLISH

(7) Denon Link connections

High quality digital sound with reduced digital signal transfer loss can be enjoyed by connecting a separately sold Denon Link compatible AV amplifier.

DVD-3910

To power outlet

Front speaker (left)

Surround speaker (left)

	Center speaker
	Front speaker (right)
DENON LINK	Subwoofer

Surround speaker (right)

AV amplifier with Denon Link input terminals

2DENON LINK Second Edition:

•With the DENON LINK, Second Edition (2nd), the audio signals are transferred from the DVD player to the AV amplifier in digital form, with the same quality as the signals recorded on the disc.

Digital transfer of the high quality multi-channel signals of DVD audio is possible for all discs. (A Second Edition compatible DVD player and AV amplifier are required for this.)

2Compatibility with previous models:

Digital audio signals output from a DENON LINK S.E. (2nd) compatible DVD player can only be played on a DENON LINK S.E. (2nd) compatible AV amplifier (Playback with DENON LINK connections is not possible when using a DENON LINK S.E. compatible DVD player in combination with an AV amplifier that is not S.E. compatible.).

• “S.E.” is indicated on the rear panel’s DENON LINK connector on DENON LINK S.E. compatible products.

2DENON LINK S.E. settings:

•At “DIGITAL INTERFACE SETUP” under “SETUP”, set “DENON LINK” to “2nd”. (See pages 32 ~ 35.) (If you connect the DENON LINK, set to “2nd”.)

16

ENGLISH

NOTES:

•When DENON LINK is set, the down-mixed audio signals are output only from the left and right terminals and front left and front right terminals.

If you want to use the analog terminals, set to “DENON LINK” to “OFF”.

•When using the DENON LINK connector, the “AUDIO CHANNEL”, “DIGITAL OUTPUT”, “LPCM (44.1kHz/48kHz)”, “SOURCE DIRECT” and “BASS ENHANCER” settings under “AUDIO SETUP” and the “HDMI AUDIO SETUP” and the “IEEE1394” settings under “DIGITAL INTERFACE SETUP” at “SETUP” cannot be made.

The digital output cannot be turned off even by setting “PURE DIRECT SELECT” to “ALL OFF” or selecting a mode for which the digital output is set to off. (See pages 47, 48.)

•The DVD-3910’s speaker settings are invalidated when the DENON LINK connector is connected.

•When the DENON LINK 2nd connection, Super Audio CD’s signals are not output from the DENON LINK connector. Please use the analog audio output terminals.

(8) IEEE 1394 connections

The simple connection of one IEEE 1394 cable permits high quality digital transfer of the following between devices having IEEE 1394 connectors: the audio of DVD video, DVD audio that up until now could only be connected by 5-conductor audio cable in an analog connection, or Super Audio CD and other multi-channel audio. (unless DENON LINK connections)

(IEEE 1394 is an international standard established by the Institute of Electrical and Electronics Engineers, Inc. of the U.S.)

DVD-3910	To power outlet

Center speaker

Front speaker (left)	Front speaker (right)
	IEEE1394
	Subwoofer

Surround speaker (left)

Surround speaker (right)

AV amplifier with IEEE 1394 terminals

17

ENGLISH

NOTES:

•Please use the included IEEE 1394 cable. When using a cable other than the included IEEE 1394 cable, please use a 4-pin IEEE 1394 cable with a length of 3.5 m or less for S400 or higher.

•The “IEEE 1394 audio signal (A&M protocol)” output from the DVD-3910’s IEEE 1394 connector not out video signals, please connecting to a TV or Monitor with “component video output” or “S-video output” or “Video output”. (See pages 10, 11.).

•The “IEEE 1394 audio signal (A&M protocol)” output from the DVD-3910’s IEEE 1394 connector can only be received on AV equipment equipped with an IEEE 1394 connector. Digital video (DV), personal computer, and i-Link (a Sony trademark) audio signals cannot be sent and received. Incorrect connections could lead to malfunction. Connect as instructed in the other device’s operating manual. Note that there is no guarantee of the operation of the connection even between devices supporting IEEE 1394. Whether or not data and control signals can be transmitted and received between devices supporting IEEE 1394 depends on the functions of the respective devices.

•When connecting using the IEEE 1394 connector, only connect one cord between the two devices. Never connect two cords between the two devices (loop connection). If this is done, the signal output from one device will return to the same device, resulting in malfunction.

•No audio signals are output from the DVD-3910’s analog connectors when IEEE 1394 is set. To use the analog connectors, set the IEEE 1394 setting to “OFF”.

•When using the IEEE 1394 mode, the “HDMI AUDIO SETUP” under “DIGITAL INTERFACE SETUP” and the “AUDIO CHANNEL”, “DIGITAL OUTPUT”, “LPCM (44.1 kHz/48 kHz)”, “SOURCE DIRECT” and “BASS ENHANCER” settings under “SETUP” – “AUDIO SETUP” cannot be made.

The digital output cannot be turned off even by setting “PURE DIRECT SELECT” to “ALL OFF” or selecting a mode for which the digital output is set to off. (See pages 47, 48.)

•When the IEEE 1394 connector is connected, the DVD-3910’s speaker settings are disabled.

•During playback of a device supporting IEEE 1394, please do not disconnect the IEEE 1394 cable of the other device, do not connect a new device, and do not switch the power on or off. Doing so may interrupt the audio.

•Among the devices that support IEEE 1394, when the power is in the standby mode or off, some devices are not able to relay data. Please see the operation manual of the connected device that supports IEEE 1394. This unit is not able to relay the IEEE 1394 data while in the standby mode.

•Devices that support IEEE 1394 have the maximum data transfer speed supported by that device marked in the vicinity of the IEEE 1394 connector. The maximum transfer speed of IEEE 1394 is defined as approximately 100/200/400 Mbps*, with 200 Mbps items having S200 inscribed and 400 Mbps items having S400 inscribed. The maximum IEEE 1394 data transfer speed of this unit is 400 Mbps. The actual transfer speed may be slower than 400 Mbps when S100 or S200 devices are connected, or

depending on the specifications of the device. Try to ensure that connections are made between devices that have the same maximum data transfer speed.

*Mbps (Mega bps) is an abbreviation of “Mega bits per second” and indicates the volume of data that can be communicated in 1 second. At 400 Mbps, 400 Mega bits of data is transferred in 1 second.

The DVD-3910’s IEEE 1394 mode is designed based on IEEE Std. 1394a-2000, Standard for a High Performance Serial Bus.

IEEE 1394 network

The following types of connections can be made between devices handling IEEE 1394 audio signals (A&M protocol): q Daisy chain connections

Connect the sets in series using a single IEEE 1394 cord. Up to 15 sets can be connected. w Tree (tower) connections

Connect the sets in parallel and in series using a single IEEE 1394 cord. Up to 63 sets can be connected.

Copyright Protection System

To play back through an IEEE 1394 connection the audio of Super Audio CD or DVD (except for discs that may be copied freely), both the player and the amplifier are required to support a copyright protection system called DTCP (Digital Transmission Content Protection). DTCP is copy protection technology comprising data encryption and the authentication of the remote device. This unit supports DTCP. Please see the operation manual of your amplifier for information about your amplifier.

18

ENGLISH

(9) HDMI connections

A simple 1-cable connection (using a commercially available cable) with a device having an HDMI (High-Definition Multimedia Interface) connector allows digital transfer of the digital images of DVD video and other sources, DVD video, and the multi-channel sound of DVD audio.

DVD-3910

HDMI Input connector

HDMI cable

(commercially available)

Monitor equipped with HDMI input connectors

			Setting of HDMI
	Audio		MULTI		MULTI
	recording	2CH
			(NORMAL)		(LPCM)
	format
	Dolby digital	2 channel	Dolby digital		Multi PCM
DVD		PCM
video	DTS	2 channel	DTS		Multi PCM
		PCM
	LPCM or P.PCM	X	X		X
DVD	(with CPPM)
Audio	LPCM or P.PCM	2 channel	Multi PCM		Multi PCM
	(without CPPM)	PCM
Video CD		2 channel	2 channel		2 channel
		PCM	PCM		PCM
	CD	2 channel	2 channel		2 channel
		PCM	PCM		PCM
MP3 CD		2 channel	2 channel		2 channel
		PCM	PCM		PCM
WMA CD		2 channel	2 channel		2 channel
		PCM	PCM		PCM
Super	Multi area	X	X		X
			X		X
Audio	Stereo area	X
CD
	CD area	2 channel	2 channel		2 channel
		PCM	PCM		PCM

The multi-channel/stereo area sound of Super Audio CD is not output.

The video and audio signals cannot be output when playing DVD AUDIO with CPPM.

Connection Examples for HDMI AUDIO SETUP

HDMI-supported monitor or projector, etc. (2-channel support or no audio support)

• 2CH························Use this connection when you would like to enjoy the multi-channel audio output from an analog audio output connector, DENON LINK, or with the audio output from an IEEE 1394 connector.

HDMI-supported monitor/AV amplifier, etc. (Supports DTS and Dolby Digital decoders)

• MULTI (NORMAL)···Use this connection when you would like to enjoy the multi-channel audio output from an HDMI connector and you wish to have a DTS, Dolby Digital, or other decoder connected to do the processing. (Speaker and other settings are not required.)

HDMI-supported monitor (Supports audio input for 2 or more channels)

• MULTI (LPCM)·······Use this connection when you would like to enjoy the multi-channel output from an HDMI connector and the connection point does not support a DTS, Dolby Digital, or other decoder. (Speaker settings are permitted.)

NOTES:
• HDMI audio output settings permit the selection of either 2	• When selecting MULTI (NORMAL) or MULTI (LPCM), the
channels or multi-channels. When selecting MULTI (NORMAL)	DVD-3910 speaker settings under “AUDIO SETUP”become
or MULTI (LPCM), a down-mixed audio signal is only output from	invalid.
the analog connectors (Left/Right and Front Left/Front Right) of	• When playing a Super Audio CD with an HDMI connection,
the DVD-3910. To output multi-channel sound from the analog	audio cannot be transferred beyond the CD area. Make an
audio output connectors, set HDMI to OFF, or select “2CH”.	analog connection for this.
• When selecting MULTI (NORMAL) or MULTI (LPCM), the	• Among the devices that support HDMI, some devices can
settings of “IEEE1394” and “DENON LINK” under “DIGITAL	control other devices via the HDMI connector; however, the
INTERFACE SETUP” of “SETUP” cannot be made. Neither	DVD-3910 cannot be controlled by another device vice the
can the settings of “AUDIO CHANNEL”, “DIGITAL	HDMI connector.
OUTPUT”, “LCPM (44.1kHz/48kHz)”, “SOURCE DIRECT”,	• When using display equipment that is not supported by the
or “BASS ENHANCER” under “AUDIO SETUP”.	HDCP (content protection function), the image will not be
The HDMI audio output is turned off if the digital output is set	output properly. (See the compatibility table.)
to “OFF” at “PURE DIRECT”, and the HDMI video and audio	• The audio signals from the HDMI connector (including the
output are both turned off if the video output is set to “OFF”	sampling frequency and bit length) may be limited by the
or if “ALL OFF” is set. (See Pages 47, 48.)	equipment that is connected.
Also note that it will not be possible to select the setting of
digital output, when selecting “MULTI (NORMAL)” at “HDMI
AUDIO SETUP”.

19

ENGLISH

(10) DVI connections

Connection with equipment that has a DVI (Digital Visual Interface)-D connector permits the transfer of digital images.

When using display equipment that is not supported by the HDCP (content protection function), the image will not be output properly. (See the compatibility table.)

Make an audio connection also because an audio signal will not be output from the DVI-D connector.

Commercially-available DVI cables are available in 24-pin and 29-pin types. The DVD-3910 supports the 24-pin DVI-D cable, but the 29pin DVI cable cannot be connected.

DVD-3910

Monitor equipped with

DVI-D input connectors

DVI-D Input connector

24P DVI-D cable (commercially available)

NOTE:

HDMI and DVI connectors.

•The table below indicates the compatibility of connections between the HDMI/DVI-D output connector of the DVD-3910 and monitors that support HDMI/DVI-D.

		Monitor with	Monitor with DVI-D	Monitor with DVI-D
		HDMI	(HDCP compatible)	(HDCP incompatible)
	HDMI output	™	™	x
	terminal	Video/Audio*1	(Only Video)*2
	DVI-D output	™	™	x
	terminal	(Only Video)	(Only Video)

Copyright Protection System

*1 Among the monitors that support HDMI, some do not support audio output (for example, projectors). In connections with equipment such as this, audio signals are not output from the HDMI output connector. Use analog audio outputs, DENON LINK, or IEEE 1394 connectors to provide the audio output at “DIGITAL INTERFACE SETUP” under “SETUP”, set “HDMI AUDIO SETUP” to “2CH”.

*2 When the set’s HDMI connector is connected to a DVI-D compatible monitor (HDCP compatible) with an HDMI-DVI converter cable (commercially available), the signals are output in digital RGB, regardless of the “HDMI/DVI SELECT” setting.

To play the digital images and sounds of DVD video or DVD audio via an HDMI/DVI-D connection, it is necessary that both the player and monitor (or AV amplifier) support a copyright protection system called HDCP (High-bandwidth Digital Content Protection System). HDCP is copy protection technology that comprises data encryption and authentication of the partner equipment. The DVD-3910 supports HDCP. Please see the user’s manual of your monitor (or AV amplifier) for information about this.

20

5PART NAMES AND FUNCTIONS

(1)Front Panel

See page 3.

q Power ON/STANDBY button

•Press once to set to the standby mode. The indicator lights up in red.

•Press again to turn the power on. The indicator lights up in green.

w Power indicator

•This indicator lights when the power is on and when the power is in the standby mode.

Light green: Power is on

Light red : Power is in the standby mode

e Power switch

•Press once to turn the power on.

•Press again to set to the “OFF” position and turn the power off.

r DENON LINK indicator

•This indicator lights when the audio signals are transferred by DENON LINK connections.

t AL24 PLUS indicator

•This indicator lights when the audio signals of a DVD, etc., are being processed digitally with the AL24 processing Plus.

y Display

• Information on the disc that is currently playing is shown on the display. (See page 22.)

u Remote control sensor

i SELECT of HDMI/DVI button

• Press this to set the video signal output from the HDMI

connector or the DVI connector.							(See page 53.)
	HDMI Y Cb Cr			HDMI RGB			DVI
		HDMI/DVI OFF

o FORMAT of HDMI/DVI button

• Press this to set the video signal format from the HDMI connector or the DVI connector. (See page 53.)

480P/576P 720P 1080i

!0VIDEO MODE button

•Use this to instantly change the adjustment mode of the stored video signals.

The unit will return to the stored setting values when the power is switched off.

(The setting values of this mode will not be stored.)

• PICTURE MODE

STD M1 M2 M3 M4 M5

• PROGRE. MODE (PROGRESSIVE)

AUTO1AUTO2 VIDEO1VIDEO2 VIDEO3

• TV TYPE

MULTINTSC PAL

• SQUEEZE MODE
No effective for interlaced image.	(See page 37.)

OFF ON

ENGLISH

!1Select the playback area/layer of SUPER AUDIO CD (SUPER AUDIO CD SETUP)

•Switch the area /layer of the Super audio CDS played with priory.

•MULTI.......When playing Super audio CDs, the Multi

			channel area is played with priory
• STEREO....			When playing Super audio CDs, the stereo
			channel area is played with priority.
• CD.............			When playing Super audio CDs, the CDs layer
			is played with priority.
	MULTI		STEREO		CD

!2PURE DIRECT SELECT button

•Press to switch the modes with the specific video signals and digital audio signals and indicate in display on and off.

(See pages 47, 48.)

NORMALMODE 1 MODE 2ALL OFF

!3DVD/AUDIO/VIDEO logo

•This indicator lights when playing the DVD audio or DVD video.

!4Super Audio CD logo

• This indicator lights when playing the Super audio CD.

!5Disc tray

• Load discs here. (See page 25.)

•Press the OPEN/CLOSE button !6to open and close the disc tray.

•The disc tray is also closed when the PLAY button !8is pressed.

!6OPEN/CLOSE button (5)

• Press this to open and close the disc tray.

(See pages 25, 56.)

!7STILL/PAUSE button (3)

• Press this to pause images or music or to play images frame by frame. (See page 58.)

!8PLAY button (1)

• Press this to play the disc. (See page 57.)

!9STOP button (2)

• Press this to stop the disc. (See page 58.)

@0Skip button (8)

• Press this to move back to the beginning of the current track (or chapter). (See page 59.)

•Press again to move back to the beginning to the previous track (or chapter).

@1Skip button (9)

• Press this to move ahead to the beginning of the next track (or chapter). (See page 59.)

@2Slow/Search buttons (6 7)

• Press this to set the slow or search play mode.

(See pages 58, 59.)

6: search in the reverse direction.

7: search in the forward direction.

21

Lights to indicate the currently playing disc. Lights in the repeat play mode.

These light to indicate the names of sections of the disc being played.

Lights during playback of multiple angles disc. Lights when the audio signals can be down-mixed. Lights in the programmed play mode.

Lights in the random play mode.

There light to indicate the time display mode. Lights when HDCD is playing.

ENGLISH

(2) Rear Panel

@3Audio output connectors (5.1ch AUDIO OUT)

•Connect using an audio cord. Connect a commercially available pin-plug cord.

@4Audio output connectors (2ch AUDIO OUT)

•Connect using the included audio video cord. Multi-channel sound is down-mixed and output.

@5Power input (AC IN)

•Connect to AC power supply using the included power supply cord.

@6Control connector (RS-232C)

• This is a terminal for future system expansion.

@7Control input connector (ROOM TO ROOM/IN)

•This is the input connector for wired remote control. Consult your DENON dealer if you wish to use this connector.

@8Control output connector (ROOM TO ROOM/OUT)

•This is the output connector for wired remote control. Consult your DENON dealer if you wish to use this connector.

@9Digital connectors (IEEE 1394)

•This is for connection of a separately sold AV amplifier equipped with a IEEE 1394 connector.

•Use it to achieve high quality digital sound with low data loss.

(3)Display

#0Digital output connector (DENON LINK)

•This is for connection of a separately sold AV amplifier equipped with a Denon Link connector.

•Use it to achieve high quality digital sound with low data loss.

#1Digital audio output connector (OPTICAL)

•Connect using an optical fiber cable (available in stores).

•Digital data is output from this connector.

#2Digital audio output connector (COAXIAL)

•Connect using an digital audio cord. Connect a commercially available 75 Ω/ohms pin-plug cord.

•Digital data is output from this connector.

#3DVI-D-Video output connector (DVI-D OUT)

•Connect using 24P DVI-D connection cord (available in stores).

#4HDMI output connector (HDMI)

• Connect using HDMI connection cord (available in stores).

#5Component video output connectors (COMPONENT VIDEO OUT)

• Connect using video cords (available in stores).

#6S-Video output connector (S-VIDEO OUT)

•Connect using an S-Video connection cord (available in stores).

#7Video output connector (VIDEO OUT)

• Connect using the included audio video cord.

q w e		r t y u i o !0 !1 !2
SUPER DVD	GROUP TITLE TRACK CHAP ANGLE D.MIX PROG		RAND TOTAL SING	REM HDCD	DIGITAL
AUDIO VCD					L.PCMP.PCM L C R LFE
1 A-B					MPEG JPEG SL S SR
PROGRESSIVE					WMA MP3 HDMI 480P	576P
F V					IEEE1394 DVI 720P	1080i
!3!4		!5			!6!7 !8

q w e

r t y u i o

!0Lights when SRS TruSurround is on.

!1Lights to indicate the currently playing audio format.

!2Lights to indicate the currently playing audio.

L	: Front left channel	S	: Mono surround channel
C	: Center channel	SR	: Surround right channel
R	: Front right channel	LFE: Low frequency effect
SL	: Surround left channel

!3Lights to indicate the currently playing video type. F :Film source

V :Video source

!4Lights when progressive video signals are being output.

!5Displays the title , track number and elapsed time during playback.

!6Lights when the audio signals is output from IEEE1394 terminals.

!7Lights when the video (or audio) signals is output from HDMI or DVI terminals.(Lights only one of the HDMI or DVI.) (Flashes while the connection to the DVI-D or HDMI connector is being checked.)

!8Lights to indicate the currently video format of HDMI or DVI terminals.

(Flashes while the connection to the DVI-D or HDMI connector is being checked.)

22

ENGLISH

6 REMOTE CONTROL UNIT

2 The DVD-3910 can be controlled from a distance using the included remote control unit (RC-972).

(1) Inserting Batteries

q Remove the remote control unit’s rear cover.

wPlace two R6P/AA batteries in the battery compartment in the direction indicated by the marks.

e Close the rear cover.

Cautions On Batteries

•Use R6P/AA batteries in this remote control unit.

•Replace the batteries with new ones approximately once a year, though this depends on the frequency with which the remote control unit is used.

•If the remote control unit does not operate from close to the main unit, replace the batteries with new ones, even if less than a year has passed.

•The included battery is only for verifying operation. Replace it with a new battery as soon as possible.

•When inserting the batteries, be careful to do so in the proper direction, following the < and > marks in the remote control unit’s battery compartment.

•To prevent damage or battery fluid leakage:

•Do not use a new battery with an old one.

•Do not use two different types of batteries.

•Do not short-circuit, disassemble, heat or dispose of batteries in flames.

•Remove the batteries when not planning to use the remote control unit for a long period of time.

•If the batteries should leak, carefully wipe off the fluid from the inside of the battery compartment, then insert new batteries.

(2) Using the Remote Control Unit

Approx. 7 meters

30° 30°

•When operating the remote control unit, point it at the remote control sensor as shown on the diagram.

•The remote control unit can be used from a direct distance of approximately 7 meters. This distance will be shorter, however, if there are obstacles in the way or if the remote control unit is not pointed directly at the remote control sensor.

•The remote control unit can be operated at a horizontal angle of up to 30° with respect to the remote control sensor.

NOTES:

•It may be difficult to operate the remote control unit if the remote control sensor is exposed to direct sunlight or strong artificial light.

•Do not press buttons on the main unit and on the remote control unit at the same time. Doing so will result in malfunction.

23

ENGLISH

(3) Names and Functions of Remote Control Unit Buttons

2 Button not explained here function in the same way as the corresponding buttons on the main unit.

		POWER OFF			POWER ON
	q
	w	HDMI/DVI		NTSC/PAL	OPEN/	!
		SELECT	FORMAT		CLOSE
					SUPER AUDIO	!9@
					CD SETUP
					PROGRAM
					/DIRECT	@1
	e
					CLEAR	@2
				SEARCH MODE CALL		@3@
	r	BACK LIGHT	ANGLE	SUBTITLE	AUDIO
						@5@
	t	TOP MENU			DISPLAY
						@7
	y
	u
		MENU			RETURN
	i					@8
	o !0	STOP	STILL/PAUSE PLAY
		SKIP		SLOW/SEARCH		#0
						@9
	!1!2 REPEAT		A-B	PAGE		#1
	!3	RANDOM	MARKER	ZOOM	DIMMER	#3#
	!4		PICTURE	PURE DIRECT
	!5!6	SETUP	ADJUST	MEMORY	SELECT	#4
	!7

q POWER ON/POWER OFF buttons

• Press this to switch the power between on and standby. w HDMI/DVI SELECT/FORMAT buttons

•Use these to select to use HDMI terminal or DVI terminal, and the format of video signals (480P/576P,720P,1080i).

e Number buttons

• Use these to input numbers.

Use the +10 button to input numbers of 10 or over. Example: To input 25

r LIGHT button

•Press this to light the opal color button. Press again this to put out light.

t ANGLE button

• Press this to switch the angle. y TOP MENU button

• The top menu stored on the disc is displayed. u Cursor buttons/ENTER button

•Use the • and ª cursor buttons to select in the vertical direction.

Use the 0 and 1 cursor buttons to select in the horizontal direction.

Press the ENTER button to select the item selected with the cursor buttons.

i MENU button

• The DVD menu stored on the disc is displayed. o STOP button (2)

!0STILL/PAUSE button (3)

!1SKIP buttons !2REPEAT button

• Press this to play tracks repeatedly.

!3A-B repeat button (A-B)

• Use this to repeat sections between two specific points.

!4RANDOM button

•Press this to play the tracks on the video or music CD in random order.

!5MARKER button

• Press this to mark places you want to see again.

!6SETUP button

• Press this to display the default setting screen.

!7PICTURE ADJUST button

• Press this to adjust the picture quality to suit your tastes.

!8OPEN/CLOSE button !9NTSC/PAL button

•Use this to switch the set’s video output format (NTSC/PAL).

@0SUPER AUDIO CD SETUP button @1PROGRAM/DIRECT button @2CLEAR button

• Press this to clear numbers that you have input.

@3CALL button

• Press this to check the program contents.

@4SEARCH MODE button

•Press this to change the search mode to search for groups or titles, tracks or chapters when selecting sections of discs directly using the number buttons.

@5AUDIO button

•For DVDs, press this to switch the audio language. For video CDs, press this to switch the channel between “STEREO”, “MONO LEFT” and “MONO RIGHT”.

@6SUBTITLE button

• Press this to switch the DVD’s subtitle language.

@7DISPLAY button

• Press this to display the ON-SCREEN.

@8RETURN button

• Press this to return to the previous menu screen.

@9PLAY button (1)

#0SLOW/SEARCH buttons #1PAGE –/PAGE + buttons

•Use these to selected the desired still picture on DVD audio discs containing browseable still pictures.

#2ZOOM button

• Press this to enlarge the image.

#3DIMMER button

•Use this to adjust the brightness of the main unit’s display. Can be switched in 4 steps, from all off to always on.

#4PURE DIRECT MEMORY/SELECT buttons

•Use these to make and select that various setting to achieve higher quality sound.

24

7 LOADING DISCS

2 Set discs in the disc tray with the labeled (printed) side facing up.

Outer disc guide

(12 cm disc)

Inner disc guide (8 cm disc)

Disc tray

NOTE:

•Do not move the DVD-3910 while a disc is playing. Doing so may scratch the disc.

(1) Opening and Closing the Disc Tray

q Turn on the power.

w Press the OPEN/CLOSE button.

Power switch

OPEN/CLOSE button

Disc tray

NOTES:

•Be sure to turn on the power before opening and closing the disc tray.

•Do not strike on the button with a pencil, etc.

ENGLISH

(2) Loading Discs

•Pick up the disc carefully so as not to touch the signal surface and hold it with the labeled side facing up.

•With the disc tray fully open, set the disc in the disc tray.

•Set 12 cm discs in the outer disc guide (Figure 1), 8 cm discs in the inner disc guide (Figure 2).

•Press the OPEN/CLOSE button. The disc is automatically loaded.

•The disc tray can also be closed automatically to load the disc by pressing the PLAY button.

Figure 1

Outer disc guide

12 cm disc

Figure 2

Inner disc guide

8 cm disc

NOTES:

•If a foreign object is caught in the disc tray during closing, simply press the OPEN/CLOSE button again and the tray will open.

•Do not press the disc tray in by hand when the power is off. Doing so will damage it.

•Do not place foreign objects in the disc tray. Doing so will damage it.

25