Denon DN-2600F Service Manual

Specifications and Main Features

It has twin mechanisms which employ compact disc players with a wired remote: Dual mechanism mountable compact disc player with a hardwire remote rester.
It is compatible with standard compact discs and 8cm discs: Compact disc players that come in standard sizes of 12cm with a supporting 8cm slot.
It has the following dimensions:
The player weighs 6 kilograms with the dimensions 482mm (width) 88mm (height) 252 (depth) without any supportive constraints.
The remote control unit weighs 3 kilograms with dimensions 482mm(width) 132mm(height) 40mm(depth)
It can be stacked in a rack of 19mouts: Can be installed in a 19 inch rack.
This component has the textures of 2 Units: For the player unit, a total of 2 U are attached.
Accessories can be altered whereas for the control unit, 3 U’s are attached.
The combined weight of the player and the remote unit is 6 kilograms and 3 kilograms, respectively:
As a whole, the remote control unit weighs approximately 6.614 pounds, in comparison to the control unit itself weighing 13.23 pounds.
U.S.A & Canada Moddels hold a power supply of 120 volts at a frequency of 60 HZ. Canadian Models supply voltage to 60 HZ:
Canadian Models operate at 120 V at a frequency of 60 HZ or its variations: 120 V AC +10 %, 60 Hz are provided by the other model.
Power Rating Specs and details have been incorporated ing to 26 watts: The total consumption rating of all devices has been bundled under a single specification: 26 W.
Having an inbuilt amplifier the entire device operates well when:
A sampling at 44.1 KHz is set at normal pitch with 16, bit linear quantization done per channel, oversizing of frequency peaks.
This regular linear frequency of 20 – 20,000 Hz gives out a output level of 1.9 Volts: Incorporating a damped output that relies on spdif as the signal level of 0.5 Vp-p 75 Ohms are well.
Using an impedance load of over 10k Ohm result in a consistent and precise consumption of output signal being exploited.
Having of releaverment of poles the instant start is done in 20 milliseconds. Pitch signalling for the range is set on 10 percent. Set in within the specifed band:
A 10% covering over unpreslvented range of pitch signalling for the set functions > considering a tension band at + 16 %.
Sample Length: The maximum length of the sample will be fifteen seconds.
Observational and Storage Requirements:

– Temperature Required for Operations: The acceptable temperature range is between 5 degrees Celsius to 35 degrees Celsius (41 to 95 degrees Fahrenheit).

– Humidity Level: An acceptable humidity range of 25% to 85% is required (no condensation).

– Storage Temperature: It is imperative that the item is stored at a temperature between -20 to 60 degrees Celsius (4 to 140 degrees Fahrenheit).

Search Precision: 1 x subcode frame 1 75 sec.
Max Scan Speed: The item will have a maximum scan speed of 20 times the normal speed.
Max Memory Steps: Maximum steps that can be memory are estimated to be around 300 steps.

Frequently Asked Questions

1. How much energy does DN-2600F use?

Its energy requirement is 26 W.

2. Does the DN-2600F work with any exclusive discs?

– Yes, the device works exclusively with standard compact discs which consists of 8 centimeter and 12 centimeter discs.

3. Was there a requirement for setting up DN-2600F?

There requirement was only that the device was prepared to be set up for 19 inches rack mounting while taking 2U space for the unit along with 3U for remote control unit.

4. What is the optimal temperature for device operation?

– The optimal temperature for device operation is between 5 to 35 degrees Celsius (41 to 95 degrees Fahrenheit).

5. Does the DN-2600F have the ability to have a working digital outputs?