The following instructions explain how to replace one or more feet on a PowerBook G4
(15-inch) computer.
Note:
Online instructions are available at http://www.info.apple.com/installparts/.
Tools
This procedure requires the following tools:
• Foot kit
• Tweezers or needlenose pliers
• Soft cloth
Preliminary Step
Before you begin, check the foot location that needs replacement and verify that the case
plug is attached. Also verify that the case plug and the case foot in the kit match the
pictures below.
glue. In the event of contact, review the safety instructions at the end of this document. For
additional information, refer to the glue manufacturer:
1. Place the computer upside down on a clean, lint-free cloth or other nonabrasive
2. Select a foot from the kit. Verify that the case plug and case foot match (refer to the
3. Make sure the plug area on the bottom case is clean. If any portion of the soft rubber
The glue used in this procedure can bond instantly to skin. Do not touch the
Elmer's Products, Inc.
Columbus, OH. 43215-3799
www.krazyglue.com
surface.
images shown in the table). Do not use a foot that does not match.
foot remains, remove it so that only the hard plastic plug is visible.
Important:
rubber foot match up and fit into the corresponding indents and bumps in the plug.
This ensures a balanced and level fitting. (Note: The picture below is of a different
foot than on your computer, and is for illustration only.)
When positioning the foot, make sure the indents and bumps of the
PowerBook G4 (15-inch FW800) Foot Replacement -
2
4.
Warning:
GLUE IS AN EYE AND SKIN IRRITANT. BONDS SKIN INSTANTLY. Do not
touch the glue at any time. Before opening the glue, review the safety instructions at
the end of this document.
Important:
The glue tube included in the kit is sealed until first use. Do not break the
seal until you are ready to use the glue. To break the seal, hold the tube upright and
away from you. Place the hollow nozzle cap on the tube and tighten it all the way
down. The tube is then ready to dispense the glue through the nozzle cap.
5. Apply one drop of glue to the plug on the bottom case. Do not spread the glue.
6. Using tweezers or needlenose pliers, carefully position the new foot so its textured
surface fits into the inner ring of the plug.
7. Using the end of the tweezers or pliers—not your finger—lightly press and hold the
foot in place for 30 seconds.
8. Before turning over the computer, allow the glue to set for at least 15 minutes.
9. Discard the tube of glue.
SAFETY INSTRUCTIONS:
GLUE IS AN EYE AND SKIN IRRITANT. BONDS SKIN
INSTANTLY. Contains ethyl cyanoacrylate. Avoid contact with skin and eyes. If eye or
mouth contact occurs, hold eyelid or mouth open and rinse thoroughly but gently with
water only for 15 minutes and GET MEDICAL ATTENTION. Liquid glue will sting eye
temporarily. Solidified glue may irritate eye like a grain of sand and should be treated by an
eye doctor. If skin bonding occurs, soak in acetone-based nail polish remover or warm
soapy water and carefully peel or roll skin apart (do not pull). Contact through clothing may
cause skin burn. If spilled on clothing, flush with cold water. Avoid prolonged breathing of
vapors. Use with adequate ventilation. KEEP OUT OF REACH OF CHILDREN.
This document is protected under U.S. Copyright Law and International Treaties, and no
part of this document may be reproduced in any form without written permission from
Apple.
Apple is not responsible for typographical, printing, or inadvertent errors.
Apple Computer, Inc.
1 Infinite Loop
Cupertino, CA 95014-2084
USA
+ 1 408 996 1010
http://www.apple.com
Apple and the Apple logo are trademarks of Apple Computer, Inc., registered in the U.S.
and other countries. PowerBook is a trademark of Apple Computer, Inc.
PowerBook G4 (15-inch FW800) Foot Replacement -
4
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.