Alinco DR138 User manual

A1.0-12/1

Alinco Incorporated, Electronics Division

Yodoyabashi Dai-bldg 13F

4-4-9 Koraibashi, Chuo-ku, Osaka 541-0043 Japan

Phone: [phone] Fax: [phone] http://www.alinco.com

E-mail:[e-mail]

VHF FM Transceiver / 136.000-173.9975MHz All EU and EFTA member states. Operator license is required.

Copyright Alinco, lnc. PS0662/FNEF-NJ

Printed in China

VHF FM Mobile Transceiver

DR-138

Instruction Manual

Thank you for purchasing your new Alinco transceiver. Please read this manual carefully before using the product to ensure full performance, and keep this manual for future reference as it contains information on after-sales service.In case addendum or errata sheets are included with this product, please read those materials and keep them together with this instruction manual for future reference.

FCC ID:PH3-DR138 IC:3070C-DR138

Introduction

Thank you very much for purchasing this excellent Alinco transceiver. Our products are ranked among the finest in the world. This radio has been manufactured with state of the art technology and it has been tested carefully at our factory. It is designed to operate to your satisfaction for many years under normal use.

Please read this manual completely from the first page to the last, to learn all the functions the product offers. It is important to note that some of the operations may be explained in relation to information in previous chapters. By reading just one part of the manual, you may risk not understanding the complete explanation of the function.

Before transmitting

There are many radio stations operating in proximity to the frequency ranges this product covers. Be careful not to cause interference when transmitting around such radio stations.

■ Lightning

Please note that no car provides adequate protection of its passengers or drivers against lightning. Therefore, Alinco will not take responsibility for any danger associated with using its radios or inside the car during lightning.

Features

■Output power selectable 60W/25W/10W

■PC-programmable

■Alphanumeric name tags

■Voice Compander (Reduce Noise & enhance audio clarity)

■Inversion Scramble(Analog encryption)

■Sub-tone (CTCSS/DCS) Encode/ Decode, DTMF/ANI,

2-tone and 5-tone

■Voice prompt in English, Various scan modes, Key lock, Wide/Narrow operations and more at NO extra costs.

Conformity Symbols

Tested to comply MIL-STD-810G

-Shock: Method 514.6/I,IV -Vibration: Method 516.6/I

Conformity Information

In case the unit you have purchased is marked with a CE symbol,a copy of relative conformity certificate or docu-ment can be reviewed at http:// www.alinco.com/usa.html.Please see the back-cover for more details.

Copyright 2012 All rights reserved. NO part of this document may be reproduced, copied, translated or transcribed in any form or by any means without the prior writhout the prior written permission of Alinco.

Inc,Osaka, Japan, English Edition Printed in China.

SAFETY TRAINING INFORMATION

WARNING:

This radio generates RF electromagnetic energy during transmission. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards.This radio is NOT intended for use by the “GeneralPopulation” in an uncontrolled environment.

• For compliance with FCC and Industry Canada RF Exposure Requirements, the transmitter antenna installation shall comply with the

following two conditions:

1.The transmitter antenna gain shall not exceed 0 dBi.

2.The antenna is required to be located outside of a vehicle and kept at a distance of 63 centimeters or more between the trans-mitting

antenna of this device and any persons during operation.For small vehicle as worst case, the antenna shall be located on the roof top at

any place on the centre line along the vehicle in order to achieve 63 centimeters separation distance. In order to ensure this distance

is met, the installation of the antenna must be mounted at least 63 centimeters away from the nearest edge of the vehicle in order to protect

against exposure to bystanders.

CAUTION:

To ensure that your exposure to RF electromag-netic energy is within the FCC allowable limits for occupationaluse, always adhere to the following guidelines:

• DO NOT operate the radio without a proper antenna attached, as

RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or an antenna specifically authorizedby the manufacturer for use with this radio.

In order to comply with RF exposure

requirements, a minimum distance of 200 cm must be maintained between

the antenna and all persons

• DO NOT transmit for more than 50% during the time of employment

(50% duty cycle or less). Transmitting excessive amount of time can cause RF exposure compliance requirements to be exceeded. Please carefully read this instruction manual to learn how to transmit and stop transmitting before starting to use it.

Electromagnetic Interference/Compatibility

During transmissions, your radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites.

Occupational/Controlled Use

This product is used in situations that users are exposed to RF as consequence of their employment provided those users are fully aware of the potential RF hazards and can exercise control over their exposure.

•This transceiver is NOT ATEX approved and NOT intended for the use in hazardous explosive atmospheres.

this may damage the radio and may also cause you to exceed FCC

●●

For Customers in Canada :

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.

L'exploitationestautoriséeauxdeuxconditionssuivantes:

(1)l'appareil ne doit pas produire de brouillage, et

(2)l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

PRECAUTIONS:

The manufacturer declines any responsibilities against loss of life and property due to a failure of this product when used with or as a part of a device made by third parties.

Use of third party accessory may result in damage to this product. It will void our warranty for repair.

Handling this product

Be sure to reduce the audio output level to minimum before using an earphone or a headset. Excessive audio may damage hearing.

Do not open the unit without permission or instruction from the manufacturer. Unauthorized modification or repair may result in electric shock, fire and/or malfunction and voids warranty.

Do not operate this product in a wet place such as in a shower room. It may result in electric shock, fire and/or malfunction, This product is splashproof but not a complete water-proof.

Do not place the product in a container carrying conductive materials, such as water or metal in close proximity. A short-circuit to the product may

result in electric shock, fire and/or malfunction.

In case of emergency

In case of the following situation(s), please turn off the product, switch off the source of power, then remove or unplug the powercord. Please contact your local dealer of this product for service and assistance. Do not use the product until the trouble is resolved. Do not try to troubleshoot the problem by yourself.

●● When a strange sound, smoke and/or strange odor comes out of the product.

●● When the product is dropped or the case is broken or cracked. ●● When a liquid penetrated inside.

●● When a power cord (including DC cables, AC cables and adapters) is damaged

For your safety, turn off then remove all related AC lines to the product and its accessories from the wall outlet if a thunderstorm is likely.

Maintenance

Do not open the unit and its accessories. Please consult with your local dealer of this product for service and assistance

Alert

Environment and condition of use

It is recommended that you check local traffic regulations regarding the use of a radio equipment while driving. Some countries prohibit or apply restrictions for the operation of radios and mobilephones while driving.

Do not use this product in close proximity to other electronic devices, especially medical ones. It may cause interference to those devices.

Keep the radio out of the reach of children.

In case a liquid leaks from the product, do not touch it. It may damage your skin. Rinse with plenty of cold water if the liquid contacted your skin.

Never operate this product in facilities where radio products are prohibited for use such as aboard aircraft, in airports, in ports, within or near the operating area of business wireless stations or their relay stations.

Use of this product may be prohibited or illegal outside of your country. Be informed in advance when you travel.

The manufacturer declines any responsibilities against loss of life and/or a property due to a failure of this product.

Do not use multiple radios in very close proximity. It may cause interference and/or damage to the product(s).

Alert

Environment and condition of use

Do not use the product in proximity to a TV or a radio. It may cause interference or receive interference.

Do not install in a humid, dusty or insufficiently ventilated place. It may result in electric shock, fire and/or malfunction.

Do not install in an unstable or vibrating position. It may result in electric shock, fire and/or malfunction when/if the product falls to the ground.

Do not install the product in proximity to a source of heat and humidity such as a heater or a stove. Avoid placing the unit in direct sunlight.

Be cautious of a dew formation. Please completely dry the product before use when it happens.

About transceiver

Do not connect devices other than specified ones to the jacks and ports on the product. It may result in damage to the devices.

Turn off and remove the power source (AC cable, DC cable, battery, cigar cable, charger adapter etc.) from the product when the product is not in use for extended period of time or in case of maintenance.

Use a clean, dry cloth to wipe off dirt and condensation from the surface of the product. Never use thinner or benzene for cleaning.

Check with your local waste officials for details on recycling or proper disposal in your area.

PC PROGRAMMING

NOTE: The utility software may be available to distributors/dealers only. USB programming cable is required. The manufacturer will not release the software to unauthorized party so please contact your dealer for details.

CONTENTS

Supplied Accessories/Optional Accessories.....................	1
Supplied Accessories.......................................................................	1
Optional Accessories........................................................................	1
Initial Installation...................................................................	2
Mobile Installation.............................................................................	2
DC Power Cable Connection............................................................	3
Fixed Station Operation....................................................................	4
REPLACING FUSES........................................................................	5
Power supply voltage Display...........................................................	5
Antenna Connection.........................................................................	5
Accessories Connections.................................................................	6
Microphone.......................................................................................	6
Getting Acquainted...........................................................	..7
Front panel........................................................................................	7
Rear panel........................................................................................	8
Display..............................................................................................	8
Microphone.......................................................................................	9
Operating MODE..................................................................................	10
Basic Operations ................................................................	11
Switching the Power On/Off ...........................................................	11
Adjusting the Volume .....................................................................	11
Switch between VFO and Channel mode ......................................	11
Adjusting Frequency/Channel Through Selector Knob...................	11
Adiusting squelch level...................................................................	11
Receiving........................................................................................	11
Transmitting....................................................................................	12

Transmitting......................................................................................	12
Transmitting Tone-burst tone ...........................................................	12
Transmitting optional signaling.........................................................	12
Memory channel programming.........................................................	12
Memory channel deletIng.................................................................	12
KEY OPERATIONS................................................................	13
squelch off/squelch off momentarry............................................	13
Frequency/MEMORY Scan..............................................................	13
MEMORY Scan................................................................................	13
CTCSS/DCS Encode and Decode setup.........................................	13
CTCSS/DCS Encode and Decode setup.........................................	14
CTCSS Scan....................................................................................	14
DCS Scan.........................................................................................	14
High/Mid/Low Power Switch.............................................................	14
Compander (Decrease the background noise and enhance audio
clarity...................................................................................................	14
Offset Direction and Offset Frequency Setup...................................	15
Keypad Lockout................................................................................	15
Current Voltage Enquiry....................................................................	15
Auto-Dialer Setup..............................................................................	15
Transmitting Edited DTMF Tones in the Auto-dialer Memory............	16
PARAMETER SETTING MODE.............................................	17
Frequency Channel Step Setup.......................................................	17
DTMF, DTMF ANI, 2Tone or 5Tone Signaling...................................	17
Sending 2-Tone Call.........................................................................	18
Sending 5-Tone Call.........................................................................	18

CONTENTS

Sending DTMF call...........................................................................	18
Signaling Combination Setup...........................................................	18
HIGH/MID/LOW Power Selection.....................................................	19
Band-width Selection........................................................................	19
TX OFF Setup...................................................................................	19
TX OFF Setup..................................................................................	20
Busy Channel Lockout......................................................................	20
Editing Channel Name......................................................................	20
Reverse TX/RX.................................................................................	20
Talk Around.......................................................................................	21
Voice Compander ............................................................................	21
Scrambler Setup (Encryption)..........................................................	21
Radio's DTMF SELF ID ENQUIRY ..................................................	21
Radio's 5TONE SELF ID ENQUIRY ................................................	21
beep sound.......................................................................................	21
TOT (Time-out timer)........................................................................	22
APO (Auto power off).......................................................................	22
DTMF Transmitting Time..................................................................	22
Display iiiumination color setting......................................................	23
Scan Dwell Time Setup....................................................................	23
LCD Backlight...................................................................................	23
tone-burst tones...............................................................................	23
Display Mode Setup.........................................................................	23
Display Mode Setup.........................................................................	24
PIN Setup ........................................................................................	24
RESET..............................................................................................	24
RESET..............................................................................................	25
Microphone Operation..........................................................	26

Function Setup By Microphone Keypad...........................................	26
Squelch Level...................................................................................	26
Optional Signaling ...........................................................................	26
Scan Skip ........................................................................................	27
Frequency/Channel Scan ................................................................	27
Busy Channel Lockout......................................................................	27
Reverse TX/RX.................................................................................	27
TOT (Time-out timer).......................................................................	28
CTCSS/DCS Encode and Decode...................................................	28
Talk Around ......................................................................................	28
Voice Prompt....................................................................................	28
HIGH/MID/LOW Power Selection.....................................................	28
HIGH/MID/LOW Power Selection.....................................................	28
LCD Backlight ..................................................................................	290
Anti-theft Alarm ....................................................................	30
	29
Cable Clone ..........................................................................	31
Programming Software Installing and Starting (in windows
XP system).............................................................................	32
Install USB Cable Driver Programme..................................................	32
Maintenance..........................................................................	33
Default Setting after Resetting(VHF)................................................	33
Trouble Shooting..............................................................................	33
Specifications.....................................................................	34
Attached Chart....................................................................	35
50 groups CTCSS Tone Frequency(Hz)...........................................	35
1024 groups DCS Code...................................................................	35
1024 groups DCS Code...................................................................	36

2 Supplied Accessories

SUPPLIED ACCESSORIES

Carefully unpack to make sure the following items are found in the package in addition to this manual:

Transceiver	Microphone (EMS-74)	Mobile Mounting	DC Power Cable with	Hardware Kit for Bracket
	(with DTMF keyboard)	Bracket	Fuse Holder	Black screws	Tapping screws	S-Washer
				(M4X8mm)	(M5X8mm)
				4PCS	4PCS

Spare Fuses (one pair)

User Manual

1

The standard accessories may vary slightly depending on the version you have purchased. Please contact your local authorized Alinco dealer should you have any questions. ALINCO and authorized dealers are not responsible for any typographical errors there may be in this manual. Standard accessories may change without notice.

Warranty Policy: Please refer to any enclosed warranty information or contact your authorized Alinco dealer / distributor for the warranty policy.

MOBILE INSTALLATION

The transceiver may be installed in any position in your car, where the controls and microphone are easily accessible and it does not interfere with the safe operation of the vehicle or the performance of the set.

If your vehicle is equipped with air bags, be certain your radio will not interfere with their deployment. If you are uncertain about where to mount the unit, contact your vehicle's manufacturer.

1.Install the mounting bracket in the vehicle using the supplied selftapping screws (4pcs) and flat washers (4pcs).

Car body

Washer (M5) Tapping screw (M5x20mm)

Mounting bracket

2.Position the transceiver, then insert and tighten the supplied hexagon SEMS screws.

Double check that all screws are tightened to prevent vehicle vibration from loosening the bracket or transceiver.

Caution:

Use only the provided screws otherwise you risk damaging the circuit board, components or fall-off of the unit.

Initial Installation 3

Determine the appropriate angle of the transceiver, using the 3 screw hole positions on the side of the mounting bracket.

2

3	Initial Installation

DC POWER CABLE CONNECTION

MOBILE OPERATION

The vehicle battery must have a nominal rating of 12V. Never connect the transceiver to a 24V battery. Be sure to use a 12V vehicle battery that has sufficient current capacity. If the current to the transceiver is insufficient, the display may darken during transmission, or transmitting output power may drop excessively.

111Route the DC power cable supplied with the transceiver directly to the vehicle's battery terminals using the shortest path from the transceiver.

Never use the cigarette lighter socket as a DC source.

The entire length of the cable must be dressed so it is isolated from heat, moisture, and the engine secondary (high voltage) ignition system/ cables.

3222After installing cable, in order to avoid the risk of damp, please use heat-resistant tap to tie together with fuse box. Don't forget to reinforce whole cable.

333In order to avoid the risk of short circuit, please cut down connection with negative (-) of battery, then connect with radio.

444Confirm the correct polarity of the connections, then attach the power cable to the battery terminals; red connects to the positive (+) terminal and black connects to the negative (-) terminal.

Never remove the fuse holders from the cable.

555Reconnect any wiring removed from the negative terminal.

Red

666Connect the DC power cable to the transceiver's power supply

connector.

Press the connectors firmly together until the locking tab clicks.

If the ignition-key on/off feature is desired(optional feature),use the

DC power cable

Ext. Power jack

optional QCC-01(For Cigar-Plug connection) cable. Connect one of the cables between the ACC terminal or a Cigar-Plug that operates with the vehicle ignition or ACC switch on the vehicle and EXT POWER jack on the rear side of the unit.

777When the ignition key is turned to ACC or ON(Start) position with the radio turned off, the power switch illuminates. The illumination will be turned off when the ignition key is turned to the off position.

To turn on the unit, press the power switch manually while it is illuminated. (While ignition key is at ACC or ON position)

888When the ignition key is turned to ACC or ON position with the radio's power switch on, the unit turns on automatically and the power switch will be lit. Turn the ignition key to OFF position or manually turn the power switch off to shut down the radio.

999Using extra cable,power consumption:5MAH.

1111Without this function,user can turn on/off radio by Power knob.

Black

ACC terminal

Cigar-Plug connection

Ext. Power jack

FIXED STATION OPERATION

In order to use this transceiver for fixed station operation, you will need a separate 13.8V DC power supply (not included) , Please contact local dealer to require.

The recommended current capacity of your power supply is 12A or more.

111Connect the DC power cable to the regulated DC power supply and ensure that the polarities are correct. (Red: positive, Black: negative).

Never directly connect the transceiver to an AC outlet.

Use the supplied DC power cable to connect the transceiver to a regulated power supply.

Do not substitute a cable with smaller gauge wires.

Regulated power supply

Red

Black

Initial Installation	3

222Connect the transceiver's DC power connector to the connector on the DC power cable.

Press the connectors firmly together until the locking tab clicks.

Before connecting the DC power to the transceiver, be sure to switch

the transceiver and the DC power supply OFF.

Do not plug the DC power supply into an AC outlet until you make all connections.

4

DC power cable with fuse holder

3	Initial Installation

REPLACING FUSES

If the fuse blows, determine the cause, then correct the problem. After the problem is resolved, replace the fuse. If newly installed fuses continue to blow, disconnect the power cable and contact your dealer for assistance.

				Fuse Location	Fuse Current Rating
				Transceiver	15A
				Supplied Accessory DC	20A
				power cable
			Only use fuses of the specified type and rating, otherwise the
	5
			transceiver could be damaged.

If you use the transceiver for a long period when the vehicle battery is not fully charged, or when the engine is OFF, the battery may become discharged, and will not have sufficient reserves to start the vehicle. Avoid using the transceiver in these conditions.

POWER SUPPLY VOLTAGE DISPLAY

After connecting the transceiver to the power supply, the supply voltage can be displayed on LCD by pressing the FUN key together with the

MONI key.

The display immediately changes as the voltage supply changes, It also displays voltage during transmission.

The transceiver will return to its normal operation when the power is switched ON or repeat above operation.

The range of displayed voltage is only from 7V to16V DC. Because the

Important displayed value is estimated, please use a voltmeter when a more precise reading is desired.

ANTENNA CONNECTION

Before operating, install an efficient, well-tuned antenna. The success of your installation will depend on the type of antenna and its correct installation.

Use a 50Ω impedance antenna and low-loss coaxial feed-line that has a characteristic impedance of 50 Ω, to match the transceiver input impedance. Coupling the antenna to the transceiver via feed-lines having an impedance other than 50Ω reduces the efficiency of the antenna system and can cause interference to nearby televisions, radio receivers and other electronic equipment.

Transmitting without first connecting an antenna or other matched load may damage the transceiver. Always connect the antenna to the transceiver before transmitting.

All fixed stations should be equipped with a lightning arrester to reduce the risk of fire, electric shock, and transceiver damage.

ACCESSORIES CONNECTIONS

EXTERNAL SPEAKER

If you plan to use an external speaker, choose a speaker with an impedance of 8 Ω. The external speaker jack accepts a 3.5 mm (1/8") mono (2-conductor) plug.

Initial Installation	3

MICROPHONE

For voice communications, connect a microphone equipped with an 8-pin modular plug into the modular socket on the front of the main unit. Press firmly on the plug until the locking tab clicks. Attach the supplied microphone hanger in an appropriate location using the screws included in the screw set.

Microphone [EMS-74]

Antenna

M i c r o p h o n e

connector

External speaker adopt double port BTL, please care about the connection. The speaker can not connect with the ground, otherwise the speaker will be fault.

Error

Ground

External speaker

6