Cisco Systems 6500-E User Manual

Size:
896.45 Kb
Download

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

Product Number: WS-SVC-CMM

Last Updated: March 23, 2009

This publication contains the procedures for installing and configuring the Catalyst 6500 series switch and Cisco 7600 series router Communication Media Module (CMM). Installation and configuration procedures are provided for the following CMM port adapters:

6-portT1 port adapter(WS-SVC-CMM-6T1)

6-portE1 port adapter(WS-SVC-CMM-6E1)

24-portFXS port adapter(WS-SVC-CMM-24FXS)

128-portad-hocconferencing and transcoding (ACT) port adapter(WS-SVC-CMM-ACT)

Note Except where specifically differentiated, the term “Catalyst 6500 series switches” includes both the Catalyst 6500 series switches and the Catalyst 6000 series switches.

Note Throughout this publication, except where specifically differentiated, the termsupervisor engine refers to Supervisor Engine 1, Supervisor Engine 2, Supervisor Engine 720, and the Supervisor Engine 32. Additionally, the termMultilayer Switch Feature Card (MSFC) refers to MSFC, MSFC2, and MSFC3.

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706USA

Contents

Contents

This publication contains these sections:

Front Panel Descriptions, page 2

Requirements, page 6

Safety Overview, page 7

Required Tools, page 10

Installing and Removing the Module, page 10

Removing and Replacing Port Adapters, page 19

Verifying the Installation, page 25

RJ-45 Port Connector and Cabling Specifications, page 25

RJ-21 Port Connector and Cabling Specifications, page 27

Accessing the Port Adapter Ports, page 28

Configuring the Port Adapter Ports, page 29

Configuring the Port Adapter Clock Source, page 29

Disaster Recovery for Module Software Upgrades, page 30

Password Recovery, page 32

Regulatory Standards Compliance, page 33

Related Documentation, page 33

Obtaining Documentation, Obtaining Support, and Security Guidelines, page 33

Front Panel Descriptions

These sections describe the front panel features of the module and the port adapters:

CMM Module, page 2

6-Port T1 and E1 Port Adapters, page 4

24-Port FXS Port Adapter, page 5

Ad-Hoc Conferencing and Transcoding Port Adapter, page 6

CMM Module

The front panel features of the modules are as follows:

STATUS LED—Whenthe module powers up, it initializes various hardware components and communicates with the supervisor engine. The STATUS LED shows the dialog with the supervisor engine and the results of the initialization. During the normal initialization sequence, the STATUS LED changes from off to red, to orange, and then to green.Table 1 describes the STATUS LED operation.

Port adapter slots—Figure 1 andFigure 2 show the E1 port adapter in the left and middle slots, with a blank filler plate in the right slot.

REAR MODULE STATUS LED—Table 2 describes the REAR MODULE STATUS LED operation.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

2

Front Panel Descriptions

Note For information on the supervisor engine LEDs, see theCatalyst 6500 Series Switch Supervisor Engine Guide at this URL:http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Module_Installation/Sup_Eng_ Guide/supe_gd.html

Figure 1

 

CMM Front Panel Features

 

 

 

 

 

 

 

 

 

 

Interface Module slots

WS-SVC-CMM

 

 

 

 

 

WS-SVC-CMM-6E1

 

 

 

 

 

WS-SVC-CMM-6E1

 

 

 

 

 

 

 

 

 

 

0

1

2

3

4

5

0

1

2

3

4

5

STATUS

 

 

 

 

 

 

 

 

 

 

 

Communication Media Module 6-PortE1 Interface Port Adapter.

 

 

 

6-PortE1 Interface Port Adapter.

 

 

 

 

 

MDL

STATUS

REAR

 

68447

STATUS LED

REAR MODULE STATUS LED

Table 1

Module STATUS LED

Color

Off

Red

Orange

Green

Description

The module is waiting for the supervisor engine to provide power.

The module is not online.

The module is not receiving power, which could be caused by the following:

Power is not available to the module.

Module temperature is over the limit1.

The module is released from reset by the supervisor engine and is booting.

If the boot code fails to execute, the LED stays red after power up.

The module is initializing hardware or communicating with the supervisor engine.

A fault occurred during the initialization sequence.

If the module fails to download its Field Programmable Gate Arrays (FPGAs) on startup, it continues initializing and is granted module online status from the supervisor engine, but the LED stays orange.

If the module is not granted module online status from the supervisor engine, the LED stays orange. This problem could be caused by the supervisor engine detecting a failure in an external loopback test that it issued to the module.

The module is operational; the supervisor engine has granted module online status.

1.Enter the show environment temperature mod command to display the temperature of each of the four sensors on the module.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

3

Front Panel Descriptions

Table 2

Rear Module STATUS LED

 

 

 

Color

 

Description

 

 

 

Green

 

Port adapter in slot 4 is up and operational.

 

 

 

Red

 

Port adapter in slot 4 is shut down.

 

 

 

No light

 

Slot 4 port adapter is not located by the system.

 

 

 

6-PortT1 and E1 Port Adapters

The front panel features of the 6-portT1 and E1 port adapters are as follows:

Receive port LEDs—TheLEDs on the front panel indicate the status of each T1 and E1 interface.Table 3 describes the receive port LED operation.

RJ-45 connectors—See the “RJ-45 Port Connector and Cabling Specifications” section on page 25 for details.

Figure 2 shows the front panels of the6-portT1 and E1 port adapters.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

4

Front Panel Descriptions

Figure 2

6-PortT1 and E1 Port Adapter Front Panel Features

Receive port LEDs

WS-SVC-CMM-6T1

0

 

1

 

 

 

2

 

 

 

3

 

 

 

4

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6-PortT1 Interface Port Adapter

68448

RJ-45connectors

Receive port LEDs

WS-SVC-CMM-6E1

0

 

1

 

 

 

2

 

 

 

3

 

 

 

4

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6-PortE1 Interface Port Adapter

RJ-45connectors

68449

Table 3

6-PortT1 and E1 Port Adapters Receive Port LEDs

 

 

 

Color

 

Description

 

 

 

Green

 

T1/E1 interface is operational.

 

 

 

Red

 

T1/E1 receive alarm.

 

 

 

Yellow

 

T1/E1 remote alarm.

 

 

 

Off

 

T1/E1 interface has been administratively shut down, or there is no

 

 

power.

 

 

 

24-PortFXS Port Adapter

The front panel features of the 24-portFXS port adapter are as follows:

Receive port LEDs—TheLEDs on the front panel indicate the status of each FXS interface.Table 4 describes the receive port LED operation.

RJ-21 connector—See the “RJ-21 Port Connector and Cabling Specifications” section on page 27 for details.

Warning If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port to a public network that follows the European Union standards. Connecting the port to this typeof public network can cause severe personal injury or can damage the unit.Statement 1031

Figure 3 shows the front panel of the24-portFXS port adapter.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

5

Requirements

Figure 3

24-PortFXS Port Adapter Front Panel Features

Receive port LEDs

WS-SVC-CMM-24FXS

FXS Interface Board Adapter

98289

 

RJ-21connector

Table 4

24-PortFXS Port Adapter Receive Port LEDs

 

 

 

Color

 

Description

 

 

 

Green

 

Port is off-hookor ringing.

 

 

 

Off

 

Port is not active (connected device on-hook)or is disabled through

 

 

the CLI.

 

 

 

Ad-HocConferencing and Transcoding Port Adapter

The front panel features of the ad-hocconferencing and transcoding port adapter are shown inFigure 4, and the STATUS LED is described inTable 5.

Figure 4

Ad-HocConferencing and Transcoding Port Adapter Front Panel Features

 

 

WS-SVC-CMM-ACT

 

 

 

 

Ad-hocConferencing and Transcoding Port Adapter

99302

Table 5

Ad-HocConferencing and Transcoding Port Adapter STATUS LED

 

 

 

Color

 

Description

 

 

 

Green

 

Port adapter is up and operational.

 

 

 

Red

 

Port adapter is shut down.

 

 

 

Off

 

Port adapter is not located by the system.

 

 

 

Requirements

These sections describe the hardware and software requirements:

Hardware Requirements, page 7

Software Requirements, page 7

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

6

Safety Overview

Hardware Requirements

The hardware requirements for the modules are as follows:

Catalyst 6500 series switch.

Cisco 7600 series router.

252.0 Watts (6.00 A @ 42 V) of available system power

A Supervisor Engine 2, Supervisor Engine 720, or Supervisor Engine 32—Thesupervisor engine can have an MSFC, MSFC2, or MSFC3, but the CMM does not require one for configuration or operation.

Supervisor Engine 32—Theminimum version for the CMM is 12.4(3) and the recommended version is 12.4(7a). The minimum version for the Supervisor Engine 32 is 12.2(18)SXF4 and the recommended version is 12.2(18)SXF4.

Port adapters—Youcan install up to three T1, E1, or FXS port adapters into slots 1 through 3 on either base module.

You can install up to four ACT port adapters into either base module. (The internally located slot 4 is reserved for the ACT port adapter.)

Note You cannot mix T1 port adapters with E1 port adapters, but any other combination of port adapters is supported.

Module blank filler plate (WS-SVC-CMM-BLANK)for unused port adapter slots.

Software Requirements

For software requirements, see the Release Notes for the Cisco Catalyst 6500 Series and the Cisco 7600 Series Communication Media Moduleat this URL:

http://www.cisco.com/en/US/products/hw/switches/ps708/prod_release_notes_list.html

Safety Overview

Throughout this publication, safety warnings appear in procedures that, if performed incorrectly, can harm you. A warning symbol precedes each warning statement.

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

7

Safety Overview

Warning Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port to a public network that follows the European Union standards. Connecting the port to this typeof public network can cause severe personal injury or can damage the unit.Statement 1031

Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.Statement 94

Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments.Statement 1051

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.

Statement 1029

Warning Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing.Statement 1034

Warning Before opening the unit, disconnect thetelephone-networkcables to avoid contact withtelephone-networkvoltages.Statement 1041

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.Statement 1036

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

8

Safety Overview

Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.Statement 1037

Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first.Statement 1026

Warning To avoid electric shock, do not connect safetyextra-lowvoltage (SELV) circuits totelephone-networkvoltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both useRJ-45connectors. Use caution when connecting cables.Statement 1021

Warning To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.Statement 1023

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

9

Required Tools

Required Tools

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

These tools are required to remove and replace the module and port adapters:

Flat-bladescrewdriver (for the module)

Number 1 Phillips screwdriver (for the screws and standoffs)

Antistatic mat or foam pad

Your own ESD-preventionequipment or the disposable grounding wrist strap that is included with all upgrade kits,field-replaceableunits (FRUs), and spares

Whenever you handle a module, always use a wrist strap or other grounding device to prevent electrostatic discharge (ESD). For information on preventing ESD, see the “Preventing ESD” section of the Regulatory Compliance and Safety Information publication.

Installing and Removing the Module

This section describes the procedures for installing and removing the module:

Installing the Module, page 10

Removing the Module, page 17

Installing the Module

This section describes how to install the module into the Catalyst 6500 series switch or the Cisco 7600 series router.

Note All modules, including the supervisor engine (if you have redundant supervisor engines), support hot swapping. You can add, replace, or remove modules without interrupting the system power or causing other software or interfaces to shut down. For more information abouthot-swappingmodules, see the

Catalyst 6500 Series Switch Module Installation Guide.

Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.Statement 94

To install the module into the Catalyst 6500 series switch or the Cisco 7600 series router, perform these steps:

Step 1 Make sure that you take the necessary precautions to prevent ESD damage.

Step 2 Choose a slot for the module.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

10

Installing and Removing the Module

Step 3 Verify that there is enough clearance to accommodate any interface equipment that you will connect directly to the module ports. If possible, place modules between empty slots that contain only module filler plates.

Step 4 Verify that the captive installation screws are tightened on all modules that are installed in the chassis.

This action ensures that the EMI gaskets on all modules are fully compressed to maximize the opening space for the replacement module.

Note If the captive installation screws are loose, the EMI gaskets on the installed modules will push adjacent modules toward the open slot, reducing the opening size and making it difficult to install the replacement module.

Step 5 Remove the module filler plate by removing the two Phillipspan-headscrews from the filler plate. (To remove a module, see the“Removing the Module” section on page 17.)

Step 6 Fully open both ejector levers on the new or replacement module. (SeeFigure 5.)

Step 7 Depending on the orientation of the slots in the chassis (horizontal or vertical), perform one of the following sets of substeps:

Horizontal slots

a.Position the module in the slot. Make sure that you align the sides of the module carrier with the slot guides on each side of the slot. (See Figure 5.)

a.Carefully slide the module into the slot until the EMI gasket along the top edge of the module makes contact with the module in the slot above it and both ejector levers have closed to approximately 45 degrees with respect to the module faceplate. (See Figure 6.)

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

11

Installing and Removing the Module

Figure 5

Positioning the Module in a Horizontal Slot Chassis

Insert module

 

 

between slot guides

EMI gasket

4

 

5

5

 

6

 

 

WS-X6K-SUP2-2GE

 

 

 

 

1

 

 

Switch

Load

 

CONSOLE

 

100%

PORT 1

 

 

PORT

 

 

PORT 2

 

MODE

 

 

 

 

CONSOLE

 

 

 

 

 

SUPERVISOR2

PCMCIA

EJECT

 

 

 

 

 

1%

 

 

 

WS-X6K-SUP2-2GE

 

 

 

 

2

 

 

Switch

Load

 

CONSOLE

 

100%

PORT 1

 

 

PORT

 

 

PORT 2

 

MODE

 

 

 

 

CONSOLE

 

 

 

 

 

SUPERVISOR2

PCMCIA

EJECT

 

 

 

 

 

1%

 

 

3

4

FAN

24 PORT 100FX

EMI gasket

-SFM

S

 

E

TU

 

TIV

TA

C

S

A

 

SWITCH FABRIC MDL

Ejector lever fully extended

58569

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

12

Installing and Removing the Module

Figure 6

Clearing the EMI Gasket in a Horizontal Slot Chassis

WS-X6K-SUP2-2GE

 

1

CONSOLE

 

 

PORT

CONSOLE

MODE

SUPERVISOR2

 

WS-X6K-SUP2-2GE

 

2

CONSOLE

 

 

PORT

CONSOLE

MODE

SUPERVISOR2

 

3

Press down

4

 

FAN

W

STATUS

 

5

 

4

 

Switch

Load

 

 

100%

 

 

 

 

PORT 1

PORT 2

PCMCIA

EJECT

 

 

 

1%

 

 

 

Switch

Load

 

 

100%

 

 

 

 

PORT 1

PORT 2

PCMCIA

EJECT

 

 

 

1%

 

 

Press down

SELECT

NEXT

5

SWITCH FABIRD MDL6

S

 

TU

E

TA

TIV

S

AC

1 mm Gap between the module EMI gasket and the module above it

58570

b.Using the thumb and forefinger of each hand, grasp the two ejector levers and press down to create a small (0.040 inch [1 mm]) gap between the EMI gasket and the module above it. (See Figure 6.)

Caution Pressing down too firmly on the levers will bend and damage them.

c.While pressing down, simultaneously close the left and right ejector levers to fully seat the module in the backplane connector. The ejector levers are fully closed when they are flush with the module faceplate. (See Figure 7.)

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

13

Installing and Removing the Module

Figure 7

Ejector Lever Closure in a Horizontal Slot Chassis

FAN STATUS

1

2

3

4

5

6

WS-X6K-SUP2-2GE

SUPERVISOR2

WS-X6K-SUP2-2GE

SUPERVISOR2

WS-C6500-SFM

WITCH FABRIC MDL

 

 

Switch

Load

 

 

CONSOLE

100%

 

 

 

 

PORT 1

 

 

PORT

 

PORT 2

CONSOLE

MODE

 

 

 

PCMCIA

 

 

 

 

EJECT

 

 

 

 

1%

 

 

 

 

Switch

Load

 

 

CONSOLE

100%

 

 

 

 

PORT 1

 

 

PORT

 

PORT 2

CONSOLE

MODE

 

 

 

 

PCMCIA

EJECT

 

 

 

 

1%

 

 

SELECT

NEXT

58571

Ejector levers flush with module faceplate

Note Failure to fully seat the module in the backplane connector can result in error messages.

d. Tighten the two captive installation screws on the module.

Note Make sure that the ejector levers are fully closed before tightening the captive installation screws.

Vertical slots

a.Position the module in the slot. (See Figure 8.) Make sure that you align the sides of the module carrier with the slot guides on the top and bottom of the slot.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

14

Installing and Removing the Module

Figure 8

Positioning the Module in a Vertical Slot Chassis

Ejector lever fully

FAN STATUS

extended

 

ICRBAFHITCWS

SFM-C6500-WS

LDM

 

 

S

 

TAT

 

US

 

AC

 

TIVE

EMI gasket

EMI gasket

63585

Insert module between slot guides

b.Carefully slide the module into the slot until the EMI gasket along the right edge of the module makes contact with the module in the slot adjacent to it and both ejector levers have closed to approximately 45 degrees with respect to the module faceplate. (See Figure 9.)

c.Using the thumb and forefinger of each hand, grasp the two ejector levers and exert a slight pressure to the left, deflecting the module approximately 0.040 inches (1 mm) to create a small gap between the module’s EMI gasket and the module adjacent to it. (See Figure 9.)

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

15

Installing and Removing the Module

Figure 9

Clearing the EMI Gasket in a Vertical Slot Chassis

Gap between the module EMI gasket and the module above it

1 mm

FABIRDSWITCH

SFM-C6500-

MDL

 

STATUS

ACTIVE

FAN

STATUS

Press left

Press left

63586

Caution Exerting too much pressure on the ejector levers will bend and damage them.

d.While pressing on the ejector levers, simultaneously close them to fully seat the module in the backplane connector. The ejector levers are fully closed when they are flush with the module faceplate. (See Figure 10.)

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

16

Installing and Removing the Module

Figure 10

Ejector Lever Closure in a Vertical Slot Chassis

FAN

STATUS

XF001TROP24

4226X-SW

STATUS

ACTIVE

NE

SE

XT

LE

 

CT

All ejector levers flush with module faceplate

US EP VR OIS 2R

ST

 

ATU

S

S

YST

CO

EM

NS

P

OLE

WR

 

MG

RESET

 

MT

CON

 

SO

 

LE

 

CO

 

MODE PORT NSOLE

 

PC

 

MC

 

IA

 

EJE

 

CT

 

1%

100 % S

 

wit

 

ch

 

Lo

 

ad

 

POR

 

T1

 

POR

 

T2

SW X- K6 S- PU

-2G2 E

SUPERVISOR2

ST

 

ATU

S

S

YST

CO

EM

NS

P OLE

WR

RE

MG

MT

SET

CONSOLE

 

MODE PORT CONSOLE

 

PCMCIA

 

EJECT

 

1%

100%

 

Switch

 

Load

 

PORT1

 

PORT2

X6K-WSSUP22GE-

63587

e. Tighten the two captive installation screws on the module.

Note Make sure that the ejector levers are fully closed before tightening the captive installation screws.

This completes the module installation procedure.

Removing the Module

This section describes how to remove the module from a Catalyst 6500 series switch or the Cisco 7600 series router.

Caution During this procedure, wear grounding wrist straps to avoid ESD damage to the module. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.

Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments.Statement 1051

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

17

Installing and Removing the Module

To remove a module from the chassis, perform these steps:

Step 1 Disconnect any network interface cables that are attached to the module.

Step 2 Verify that the captive installation screws on all of the modules in the chassis are tight.

This step assures that the space that is created by the removed module is maintained.

Note If the captive installation screws are loose, the electromagnetic interference (EMI) gaskets on the installed modules will push the modules toward the open slot, reducing the opening size and making it difficult to install the replacement module.

Step 3 Loosen the two captive installation screws on the module.

Step 4 Depending on the orientation of the slots in the chassis (horizontal or vertical), perform one of the following sets of substeps:

Horizontal slots

a.Place your thumbs on the left and right ejector levers, and simultaneously rotate the levers outward to unseat the module from the backplane connector.

b.Grasp the front edge of the module, and slide the module part of the way out of the slot. Place your other hand under the module to support the weight of the module. Do not touch the module circuitry.

Vertical slots

a.Place your thumbs on the ejector levers that are located at the top and bottom of the module, and simultaneously rotate the levers outward to unseat the module from the backplane connector.

b.Grasp the edges of the module, and slide the module straight out of the slot. Do not touch the module circuitry.

Step 5 Place the module on an antistatic mat or antistatic foam, or immediately reinstall it in another slot.

Step 6 If the slot from which you removed the module is to remain empty, install a module filler plate to keep dust out of the chassis and to maintain proper airflow through the chassis.

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.

Statement 1029

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

18

Removing and Replacing Port Adapters

Removing and Replacing Port Adapters

Follow the procedures in this section to remove and replace the port adapters on the CMM:

Removing a Port Adapter from Module Slots 1 through 3, page 19

Installing a Port Adapter in Module Slots 1 through 3, page 22

Installing and Removing an Ad-Hoc Conferencing and Transcoding Port Adapter in Slot 4, page 23

Removing a Port Adapter from Module Slots 1 through 3

Note When you face the module front panel, slot 1 is on the left, slot 2 is in the middle, and slot 3 is on the right. Slot 4 is located internally. (SeeFigure 13.)

To remove a port adapter, perform these steps:

Warning Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing.Statement 1034

Step 1 Remove the module from the Catalyst 6500 series switch or the Cisco 7600 series router; see the“Removing the Module” section on page 17.

Step 2 Carefully place the module,component-sidedown, on an antistatic mat or foam pad with the front of the module facing toward you. (SeeFigure 11.)

Step 3 Remove the two Phillips screws securing the port adapter. (SeeFigure 11.)

Step 4 Carefully turn the modulecomponent-sideup and place it on the antistatic mat or foam pad.

Step 5 Remove the two standoffs and the two remaining Phillips screws securing the port adapter. (SeeFigure 12.)

Step 6 Note the location of the two connectors inFigure 13 and remove the port adapter, taking care when lifting up and disconnecting the port adapter from the connectors.

Tip To unseat the port adapter from the two connectors, grasp the rear of the port adapter with one hand, and gently but firmly pull up on the rear of the port adapter until it is free of the connectors.

Step 7 Place the removed port adapter in an antistatic bag.

Step 8 If leaving an empty slot, install a blank filler plate.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

19

Removing and Replacing Port Adapters

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.

Statement 1029

Step 9 To install the module into the Catalyst 6500 series switch or the Cisco 7600 series router, see the“Installing the Module” section on page 10.

Figure 11

Module (Bottom View)

STATUSREAR MDL

6

5

4

3

2

1

 

6

5

4

3

2

1

WS-X6600-6TI

STATUS

WS-X6600-6EI

WS-X6600

Phillips screws (6) (installed from bottom)

68446

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

20

Removing and Replacing Port Adapters

Figure 12 Module (Top View with Port Adapters Installed)

Slot 4 standoffs (2)

Standoffs (6)

Phillips screws (6)

WS-X6600

WS-X6600-6TI

1

2

3

4

5

6

WS-X6600-6EI1

2

3

4

5

6

STATUS

 

 

 

 

 

 

 

 

 

 

 

 

AVVID Services Module

6Port TI Intfc Mdl

 

 

 

 

 

 

6Port EI Intfc Mdl

 

 

 

 

 

Slot 4 Phillips

screws (2)

MDL

68453

REAR

STATUS

 

Figure 13 Module (Top View with Port Adapters Removed)

Slot 4 connectors (2)

Slot 4 standoff

mounting

posts (2)

Standoff mounting

posts (6)

Port adapter connectors (6)

Phillips screw mounting posts (6)

Slot1

Slot2

Phillips screw access holes (6)

Slot 4 Phillips

screw mounting

posts (2)

Slot3

68452

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

21

Removing and Replacing Port Adapters

Installing a Port Adapter in Module Slots 1 through 3

Note When you face the module front panel, slot 1 is on the left, slot 2 is in the middle, and slot 3 is on the right. Slot 4 is located internally. (SeeFigure 13.)

To install a port adapter in module slots 1 through 3, perform these steps:

Warning Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing.Statement 1034

Step 1 Remove the module from the Catalyst 6500 series switch or the Cisco 7600 series router; see the“Removing the Module” section on page 17.

Step 2 Carefully place the module,component-sideup, on an antistatic mat or foam pad with the front of the module facing toward you.

Step 3 If there is a blank filler plate installed, remove it.

Step 4 Remove the new port adapter from its antistatic bag.

Step 5 Locate the slot in which you are going to install the port adapter. Note the location of the following items (seeFigure 13):

Two port adapter connectors

Two standoff mounting posts

Two Phillips screw mounting posts

Two Phillips screw access holes

Step 6 Align the port adapter with the mounting posts and mounting holes. Ensure that the connectors on the port adapter are aligned with the connectors on the module.

Step 7 When all mounting posts and mounting holes are aligned, gently push down on the port adapter edges to ensure that the keys on the connectors are properly aligned. If necessary, while applying pressure with your left hand, rock the module up and down slightly with your right hand to seat the port adapter.

Tip To seat the port adapter into the two connectors, grasp the rear of the port adapter with one hand, and gently but firmly push down on the rear of the port adapter until it is seated in the connectors. You will hear a distinctive “click” when the port adapter seats in the connectors.

Caution Use care not to damage the connectors on the port adapter. If you damage a connector, you will have to return the port adapter to Cisco for repair.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

22

Removing and Replacing Port Adapters

Caution Using the screws or standoffs to seat the port adapter could warp the port adapter.Before you install and tighten the securing screws, ensure that the port adapter is fully seated by visually verifying that the bottom of the port adapter is in contact with the top of the mounting posts.

Step 8 Install the two standoffs and two Phillips screws to secure the port adapter. (SeeFigure 12.)

Step 9 Carefully turn the modulecomponent-sidedown, and place it on the antistatic mat or foam pad.

Step 10 Install the two remaining Phillips screws. (SeeFigure 11.)

Step 11 Install the module into the Catalyst 6500 series switch or the Cisco 7600 series router; see the“Installing the Module” section on page 10.

Installing and Removing an Ad-HocConferencing and Transcoding Port Adapter in Slot 4

Note Thead-hocconferencing and transcoding port adapter is the only port adapter that can be installed in slot 4. Slot 4 is located internally. (SeeFigure 13.)

Warning Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing.Statement 1034

Follow these procedures to remove and install an ad-hocconferencing and transcoding port adapter in slot 4:

Removing an Ad-Hoc Conferencing and Transcoding Port Adapter in Slot 4, page 23

Installing an Ad-Hoc Conferencing and Transcoding Port Adapter in Slot 4, page 24

Removing an Ad-HocConferencing and Transcoding Port Adapter in Slot 4

To remove a port adapter in module slot 4, perform these steps:

Step 1 Remove the module from the Catalyst 6500 series switch or Cisco 7600 series router; see the“Removing the Module” section on page 17.

Step 2 Carefully place the module, component side up, on an antistatic mat or foam pad with the front of the module facing toward you.

Step 3 InFigure 13, note the location of the two slot 4 Phillips screw mounting posts. Remove the two Phillips screws that secure theright-handside of the port adapter.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

23

Removing and Replacing Port Adapters

Step 4 InFigure 13, note the location of the two slot 4 standoff mounting posts. Remove the two mounting posts that secure the port adapter.

Step 5 InFigure 13, note the location of the two slot 4 connectors. Carefully remove the port adapter, taking care when lifting up and disconnecting the port adapter from the connectors.

Tip To unseat the port adapter from the two connectors, grasp theleft-handside of the port adapter with one hand, and gently but firmly pull up on the port adapter until it is free of the connectors.

Step 6 Place the removed port adapter in an antistatic bag.

Step 7 Install the module into the Catalyst 6500 series switch or the Cisco 7600 series router; see the“Installing the Module” section on page 10.

Installing an Ad-HocConferencing and Transcoding Port Adapter in Slot 4

To install a port adapter in module slot 4, perform these steps:

Note To install a port adapter in module slot 4, you need to remove the face plate from the port adapter. To remove the face plate, position the port adapter with the face plate facing toward you, turn the port adapter component side down on an antistatic mat or foam pad, and then remove the two Phillips screws that secure the face plate.

Step 1 Remove the module from the Catalyst 6500 series switch or the Cisco 7600 series router; see the“Removing the Module” section on page 17.

Step 2 Carefully place the module, component side up, on an antistatic mat or foam pad with the front of the module facing toward you.

Step 3 InFigure 13, note the location of the two, slot 4 Phillips screw mounting posts, and note the location of the two, slot 4 standoff mounting posts.

Step 4 Align the port adapter with the two slot 4 Phillips screw mounting posts and two slot 4 standoff mounting posts. Ensure that the connectors on the port adapter are aligned with the connectors on the module.

Step 5 When all mounting posts and mounting holes are aligned, gently push down on the port adapter edges that ensure that the keys on the connectors are properly aligned. If necessary, while applying pressure with your left hand, rock the module up and down slightly with your right hand to seat the port adapter.

Tip To seat the port adapter into the two connectors, grasp theleft-handside of the port adapter with one hand, and gently but firmly push down on theleft-handside of the port adapter until it is seated in the connectors. You will hear a distinctive “click” when the port adapter seats in the connectors.

Caution Use care not to damage the connectors on the port adapter. If you damage a connector, you will have to return the port adapter to Cisco for repair.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

24

Verifying the Installation

Caution Using the screws or standoffs to seat the port adapter could warp the port adapter.Before you install and tighten the securing screws, ensure that the port adapter is fully seated by visually verifying that the bottom of the port adapter is in contact with the top of the mounting posts.

Step 6 Install the two standoffs and two Phillips screws to secure the port adapter. (SeeFigure 12.)

Step 7 Install the module into the Catalyst 6500 series switch or Cisco 7600 series router; see the“Installing the Module” section on page 10.

Verifying the Installation

Enter the show module mod-num command to verify that the system acknowledges the new module and has brought it online.

This example shows the output of the show module command with a module in slot 4:

Console>

(enable) show module 4

 

 

 

Mod

Slot

Ports Module-Type

Model

 

Sub Status

---

----

-----

-------------------------

-------------------

-----------

4

4

5

Communication Media Mod.

WS-SVC-CMM

no ok

Mod

Module-Name

 

Serial-Num

 

 

 

---

--------------------

-----------

 

 

 

4

 

 

 

sad054206jc

 

 

 

Mod

MAC-Address(es)

 

Hw

Fw

Sw

---

--------------------------------------------

----------

-----------------

4

00-01-64-46-6a-0eto

00-01-64-46-6a-171.0

12.2(2002012.2(20020530:100440

RJ-45Port Connector and Cabling Specifications

Warning Before opening the unit, disconnect thetelephone-networkcables to avoid contact withtelephone-networkvoltages.Statement 1041

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.Statement 1036

Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.Statement 1037

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

25

RJ-45Port Connector and Cabling Specifications

Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first.Statement 1026

Warning To avoid electric shock, do not connect safetyextra-lowvoltage (SELV) circuits totelephone-networkvoltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both useRJ-45connectors. Use caution when connecting cables.Statement 1021

Warning To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.Statement 1023

The T1 and E1 port adapter RJ-45port connector and cabling specifications are described in this section:

Figure 14 shows theRJ-45port cable connector pin orientation.

Table 6 describes theRJ-45port pinouts.

Figure 14 RJ-45Port Connector

Pin 1

Pin 8

Table 6

Pin1

1

2

3

4

5

6

7

8

RJ-45(both ends)

192661

6-PortT1 and E1 Port AdapterRJ-45Port Pinouts

Description

Receive R1

Receive T1

Not connected

Transmit R

Transmit T

Not connected

Not connected

Not connected

1. Table 6 lists the pinouts for theRJ-45port connector, not the pinouts of the cable connecting to the port.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

26

RJ-21Port Connector and Cabling Specifications

RJ-21Port Connector and Cabling Specifications

Warning If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port to a public network that follows the European Union standards. Connecting the port to this typeof public network can cause severe personal injury or can damage the unit.Statement 1031

Caution Do not connect theWS-SVC-CMM-24FXSport adapter directly to a voicemail server, IVR application, or fax server if the servers have unused wiring pairs with voltage on them. We recommend that you connect the25-paircables topunch-downblocks and cross connect to the voicemail, IVR, or fax servers. If you do not usepunch-downblocks and cross connects to theWS-SVC-CMM-24FXSport adapter, you could damage the port adapter. For example, theFLT-8card for the Octel 250 uses every other pair for its voice ports. The unused pairs have +36 VDC acrossring-to-groundin anon-hookcondition, and this high voltage has been known to damage theWS-SVC-CMM-24FXSport adapter.

Use a standard RJ-21Category 5 telco connector and cable to connect to theRJ-21connector. Two types ofRJ-21connectors are shown inFigure 15 andFigure 16. A pinout for the module’sRJ-21connector is provided inTable 7.

Figure 15 RJ-21Telco Interface90-DegreeCable Connector

11485

Figure 16 RJ-21Telco Interface180-DegreeCable Connector

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

27

Accessing the Port Adapter Ports

Table 7

RJ-21Connector Pinouts

 

 

 

 

 

 

 

 

 

Port

Connector Pin

 

Port

Connector Pin

 

Number

Number

Signal

Number

Number

Signal

 

 

 

 

 

 

1

1

Ring

13

13

Ring

 

26

Tip

 

38

Tip

 

 

 

 

 

 

2

2

Ring

14

14

Ring

 

27

Tip

 

39

Tip

 

 

 

 

 

 

3

3

Ring

15

15

Ring

 

28

Tip

 

40

Tip

 

 

 

 

 

 

4

4

Ring

16

16

Ring

 

29

Tip

 

41

Tip

 

 

 

 

 

 

5

5

Ring

17

17

Ring

 

30

Tip

 

42

Tip

 

 

 

 

 

 

6

6

Ring

18

18

Ring

 

31

Tip

 

43

Tip

 

 

 

 

 

 

7

7

Ring

19

19

Ring

 

32

Tip

 

44

Tip

 

 

 

 

 

 

8

8

Ring

20

20

Ring

 

33

Tip

 

45

Tip

 

 

 

 

 

 

9

9

Ring

21

21

Ring

 

34

Tip

 

46

Tip

 

 

 

 

 

 

10

10

Ring

22

22

Ring

 

35

Tip

 

47

Tip

 

 

 

 

 

 

11

11

Ring

23

23

Ring

 

36

Tip

 

48

Tip

 

 

 

 

 

 

12

12

Ring

24

24

Ring

 

37

Tip

 

49

Tip

 

 

 

 

 

 

25, 50, 51, 52

GND

 

 

 

 

 

 

Accessing the Port Adapter Ports

From the module command-lineinterface (CLI), you identify each port adapter byinterface_name followed byslot_num/port_num. For example, to configure the first port on a6-portT1 port adapter that is installed in slot 2, specifyT1 2/0. For the second port, specifyT1 2/1, and so on.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

28

Configuring the Port Adapter Ports

Configuring the Port Adapter Ports

Configuring the module interfaces is similar to configuring the voice interfaces on other Cisco products. module interface configuration requirements are dependent on your AVVID network requirements.

Note The module requires a static IP address. Obtaining an IP address through a DHCP server is not supported. You assign an IP address to the module Gigabit Ethernet backplane interface through the CLI by using theinterface GigabitEthernet1/0 command.

Configuring the Port Adapter Clock Source

The module T1/E1 port adapter clock configuration is the same as the configuration on many other Cisco gateways. The CLI commands that are used for configuring the clock are identical to other gateways. To set clocking for individual T1 or E1 ports, enter the clock source command in controller configuration mode as follows:

clock source {line[primary| secondary{1..17}] | internal}

To return to the default configuration, use the no clock source command.

Note We do not recommend that you use theclock source line command. You must enter either theclock source line primary command or theclock source line secondary command.

If you configure the clock source for a port adapter port as primary, the Rx clock that is received from the remote end is used to supply the clock for all module T1/E1 ports that are configured for the internal clock on that module. Only one port adapter port can be configured as the primary clock source on a module. If you do not configure any of the port adapter ports as the primary clock source, the internal TDM system clock uses the free running clock on one of the port adapters.

If you configure the clock source for a port adapter port as secondary, you must also specify the priority preference level of the source. The system automatically switches among the secondary sources to use the highest level of preference that has the Rx clock available when the specified primary clock source is absent.

If you configure the clock source for a port adapter port as internal, the port uses the clock that is provided by the system. This system clock could be a module internal clock or the Rx clock from the port that is configured as the primary clock source.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

29

Disaster Recovery for Module Software Upgrades

Disaster Recovery for Module Software Upgrades

This section describes how to recover in the event that the CMM software image fails to load properly. If there is a corrupted image in the CMM bootflash, the CMM does not come online and stays at the ROMMON prompt. You will need to perform these steps to replace the corrupted image:

Step 1 Copy a new image to the supervisor engine flash memory.

Step 2 Download the image from the supervisor engine to the CMM bootflash.

Step 3 Configure the system by using the power management bits to control which image is booted when the CMM is reset.

Note The downloaded image must be the same version that was previously operating on the CMM. Failure to perform the disaster recovery with the same image version could result in corrupted port adapters.

Note To successfully perform disaster recovery on the Supervisor Engine 720, you must have the ROMMON version 12.2(1r)T2 on the CMM.

Use Table 8 for configuring the filename aliases and the boot or power management options for different Catalyst 6500 series supervisor engines.

Table 8 CMM Filename Aliases and Boot Options for Disaster Recovery

Supervisor Engine Model

File Name Alias

Boot/Power Management Option

 

 

 

 

Supervisor Engine 1

slot0:ws-svc-cmm

Cisco IOS Software

Catalyst Operating System

 

 

 

Software

 

 

 

 

Supervisor Engine 2

 

6 — For supervisor

10 — For supervisor

 

 

engine in slot 1

engine in slot 1

Supervisor Engine 32

 

 

7— For supervisor

11 — For supervisor

 

 

 

 

engine in slot 2

engine in slot 2

 

 

 

 

Supervisor Engine 720

disk0:ws-svc-cmm

10 — For supervisor engine in slot 5 or 7

 

 

11 — For supervisor engine in slot 6 or 8

 

 

 

 

These sections provide disaster recovery procedures:

Disaster Recovery for Supervisor Engines Running Catalyst Operating System Software, page 31

Disaster Recovery for Supervisor Engines Running Cisco IOS Software, page 31

Tip If the CMM image fails to load properly, a crash information file is generated and then saved in the CMM bootflash.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

30

Disaster Recovery for Module Software Upgrades

Disaster Recovery for Supervisor Engines Running Catalyst Operating System Software

To perform disaster recovery on systems that use the Catalyst operating system software on the supervisor engine, perform these steps:

Step 1 Before performing the disaster recovery, remove the port adapters from the CMM.

See the “Removing and Replacing Port Adapters” section on page 19 for removal procedures.

Step 2 Enter thecopy tftp [device] command to copy the golden image for the CMM to the supervisor engine flash memory where [device] can be any flash file system on the supervisor engine.

Step 3 Enter theset filename-alias [alias-name][device]:[golden-image]command to translate the filename of the downloaded file.

The [golden-image]is the file to be downloaded, and the [device] can be any flash file system on the supervisor engine. SeeTable 8 for configuring the appropriate[alias-name]corresponding to the supervisor engine type in use.

Step 4 Enter theset module power down [mod] [pm_option] command to power down the CMM.

See Table 8 for configuring the appropriate [pm_option] corresponding to the supervisor engine type in use.

Step 5 Enter theset poll disable command to disable polling.

Step 6 Enter theset module power up [mod] command to power up the CMM.

When the CMM powers up, disaster recovery is complete.

Step 7 After you complete the disaster recovery, enter theclear filename-alias [alias-name]command to terminate the filename translation.

Step 8 Set the power management option for the CMM to zero (0).

This step is necessary to prevent the download mechanism from triggering every time that the CMM is reset.

Step 9 Enter theset poll enable command to enable polling.

Disaster Recovery for Supervisor Engines Running Cisco IOS Software

Note This procedure requires supervisor engine software release 12.2(18)SFX or later.

To perform disaster recovery on systems that use Cisco IOS software on the supervisor engine, perform these steps:

Step 1 Before performing the disaster recovery, remove the port adapters from the CMM.

See the “Removing and Replacing Port Adapters” section on page 19 for removal procedures.

Step 2 Enter thecopy tftp [device] command to copy the golden image for the CMM to the supervisor engine flash memory where [device] can be any flash file system on the supervisor engine.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

31

Password Recovery

Step 3 Under the CLI Config mode, enter thetftp-server [device]:[golden-image]alias [alias-name]command to translate the filename of the downloaded file.

The [golden-image]is the file to be downloaded, and the [device] can be any flash file system on the supervisor engine. SeeTable 8 for configuring the appropriate[alias-name]corresponding to the supervisor engine type in use.

Step 4 Under the CLI exec mode, enter thehw-module module [mod]boot [pm_option] command to set the power management option for the CMM.

See Table 8 for configuring the appropriate [pm_option] corresponding to the supervisor engine type in use.

Step 5 Enter thehw-module module [mod]reset command to reset the module.

When the CMM powers up, disaster recovery is complete.

Step 6 After you complete the disaster recovery, under CLI config mode, enter theno tftp-server [device]:[golden-image]command to remove the filename translation.

Step 7 Set the power management option for the CMM to zero (0) by entering the commandhw-module module [mod]boot config-register.

This step is necessary to prevent the download mechanism from triggering every time that the CMM is reset.

Password Recovery

Before performing the password recovery procedure, you must console into the CMM by performing these steps:

Step 1 Remove the CMM from the chassis. For removal information, see the“Removing the Module” section on page 17.

Note There are twoRJ-45ports on the CMM motherboard. The second one towards the edge or end of the motherboard is the console port.

Step 2 Connect astraight-throughcable, not a regular rolled flat cable, to the console port on the motherboard.

Step 3 Remove the module directly above the CMM to allow a space for the console cable to run from the CMM motherboard to outside of the chassis.

Step 4 Reinstall the CMM into the chassis.

Step 5 Perform the recovery procedure in Password Recovery Procedure for the Catalyst 6500/6000 SeriesSwitches Running Cisco IOS System Software to recover the password for the CMM.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

32

Regulatory Standards Compliance

Regulatory Standards Compliance

Catalyst 6500 series switches and modules comply with the regulatory standards that are listed in the

Regulatory Compliance and Safety Information for the Catalyst 6500 Series Switches publication at this URL:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/RC/78_12928.html

Cisco 7600 series routers comply with the regulatory standards that are listed in the Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers publication at this URL:

http://www.cisco.com/en/US/docs/routers/7600/Hardware/RCSI/78_13690.html

California Perchlorate Contamination Prevention Act (Title 22, California Code of Regulations, Chapter 33)

The battery inside this product may contain perchlorate material, a known hazardous substance, so special handling and disposal of this product might be necessary.

For more information about perchlorate and best management practices for perchlorate-containingsubstances, seehttp://www.dtsc.ca.gov/hazardouswaste/perchlorate/.

Related Documentation

For more detailed installation and configuration information, see these publications:

Regulatory Compliance and Safety Information for the Catalyst 6500 Series Switches

Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers

Catalyst 6500 Series Switch Module Installation Guide

Cisco 7600 Series Router Module Installation Guide

Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide

Cisco 7600 Series Router Cisco IOS Software Configuration Guide

Catalyst 6500 Series Switch Cisco IOS Command Reference

Cisco 7600 Series Router Cisco IOS Command Reference

Obtaining Documentation, Obtaining Support, and Security

Guidelines

For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

33

Obtaining Documentation, Obtaining Support, and Security Guidelines

This document is to be used in conjunction with the documents listed in the “Related Documentation” section.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks.Third-partytrademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

34