IMPORTANT!
READ CAREFULLY BEFORE USE.
KEEP THIS GUIDE FOR FUTURE REFERENCE.
This is a User’s Guide for a series of products. Not all products support all firmware features. Screenshots
and graphics in this book may differ slightly from your product due to differences in your product
firmware or your computer operating system. Every effort has been made to ensure that the information
in this manual is accurate.
Related Documentation
•Quick Start Guide
The Quick Start Guide shows how to connect the NWA1000 Series and access the Web Configurator.
•CLI Reference Guide
The CLI Reference Guide explains how to use the Command-Line Interface (CLI) and CLI commands
to configure the NWA1000 Series.
Note: It is recommended you use the Web Configurator to configure the NWA1000 Series.
• Web Configurator Online Help
Click the help icon in any screen for help in configuring that screen and supplementary information.
• Nebula Control Center User’s Guide
This User’s Guide shows how to manage the NWA1000 Series remotely. Most features of these devices
can be managed through Nebula Control Center.
•More Information
Go to https://businessforum.zyxel.com for product discussions.
Go to support.zyxel.com to find other information on the NWA1000 Series
.
NWA1000 Series User’s Guide
2
Document Conventions
Warnings and Notes
These are how warnings and notes are shown in this guide.
Warnings tell you about things that could harm you or your device.
Note: Notes tell you other important information (for example, other things you may need to
configure or helpful tips) or recommendations.
Syntax Conventions
• All models in this series may be referred to as the “NWA1000 Series” in this guide.
• Product labels, screen names, field labels and field choices are all in bold font.
• A right angle bracket ( > ) within a screen name denotes a mouse click. For example, Configuration > Network > IP Setting means you first click Configuration in the navigation panel, then the Network sub
menu and finally the IP Setting tab to get to that screen.
Icons Used in Figures
Figures in this guide may use the following generic icons. The NWA1000 Series icon is not an exact
representation of your device.
User ......................................................................................................................................................... 91
AP Profile ................................................................................................................................................ 98
System .................................................................................................................................................. 135
Log and Report ................................................................................................................................... 158
8.1.1 What You Can Do in this Chapter ....................................................................................... 58
8.2 What You Need to Know ............................................................................................................... 58
8.3 Network Status ................................................................................................................................ 59
8.3.1 Port Statistics Graph .............................................................................................................. 61
8.4 Radio List ......................................................................................................................................... 62
8.4.1 AP Mode Radio Information ................................................................................................63
8.5 Station List ....................................................................................................................................... 65
NWA1000 Series User’s Guide
6
Table of Contents
8.6 WDS Link Info ................................................................................................................................... 66
9.1.1 What You Can Do in this Chapter ....................................................................................... 72
9.2 IP Setting ......................................................................................................................................... 72
10.1.1 What You Can Do in this Chapter ..................................................................................... 78
10.1.2 What You Need to Know ...................................................................................................79
10.2 AP Management .......................................................................................................................... 79
10.3 Rogue AP ....................................................................................................................................... 82
10.3.1 Add/Edit Rogue/Friendly List .............................................................................................. 84
11.3.1 Edit User Authentication Timeout Settings ........................................................................ 96
Chapter 12
AP Profile.............................................................................................................................................98
12.1.1 What You Can Do in this Chapter ..................................................................................... 98
12.1.2 What You Need To Know ...................................................................................................98
12.2 Radio .............................................................................................................................................. 99
12.2.1 Add/Edit Radio Profile ...................................................................................................... 100
12.4 Security List .................................................................................................................................. 109
12.5 MAC Filter List .............................................................................................................................. 113
12.5.1 Add/Edit MAC Filter Profile ............................................................................................... 113
12.6 Layer-2 Isolation List .................................................................................................................... 114
26.1.1 What You Can Do in this Chapter ................................................................................... 199
26.2 IP Setting ..................................................................................................................................... 199
This User’s Guide covers the following models: NWA1123-ACv2, NWA1123-AC PRO, NWA1123-AC HD,
and NWA1302-AC. Your NWA1000 Series is a wireless Access Point (AP). The NWA1000 Series extends the
range of your existing wired network without additional wiring, providing easy network access to mobile
users. You can set up a wireless network with other IEEE 802.11a/b/g/n/ac compatible devices. The
NWA1000 Series is able to function both 2.4GHz and 5GHz networks at the same time.
Table 1 NWA1000 Series Comparison Table
FEATURESNWA1123-ACV2
Supported Wireless
Standards
Supported Frequency
Bands
Available Security ModesNone
Number of SSID Profiles64646464
Number of Wireless Radios2222
Rogue APs DetectionYesYesYesYes
WDS (Wireless Distribution
System) - Root AP &
Repeater Modes
You can set the NWA1000 Series to operate in either standalone or cloud mode. Cloud mode means
the device is managed over the Internet using Nebula Control Center (NCC), as discussed in Chapter 23
on page 191. When the NWA1000 Series is in standalone mode, it can serve as a:
NWA1000 Series User’s Guide
12
Chapter 1 Introduction
•regular AP
• root AP
• wireless repeater
The root AP or wireless repeaters establish wireless links with other APs in a Wireless Distribution System
(WDS). A WDS is a wireless connection between two or more APs.
Your NWA1000 Series’s business-class reliability, SMB features, and centralized wireless management
make it ideally suited for advanced service delivery in mission-critical networks. It uses Multiple BSSID and
VLAN to provide simultaneous independent virtual APs. Additionally, innovations in roaming technology
and QoS features eliminate voice call disruptions.
The NWA1000 Series controls network access with Media Access Control (MAC) address filtering, and
rogue Access Point (AP) detection. It also provides a high level of network traffic security, supporting IEEE
802.1x, Wi-Fi Protected Access 2 and Wired Equivalent Privacy (WEP) data encryption.
Your NWA1000 Series is easy to install, configure and use. The embedded Web-based configurator
enables simple, straightforward management and maintenance. See the Quick Start Guide for making
hardware connections.
1.2 Applications
This section shows some examples of using the NWA1000 Series in various network environments.
1.2.1 MBSSID
A Basic Service Set (BSS) is the set of devices forming a single wireless network (usually an access point
and one or more wireless clients). The Service Set IDentifier (SSID) is the name of a BSS. In Multiple BSS
(MBSSID) mode, the NWA1000 Series provides multiple virtual APs, each forming its own BSS and using its
own individual SSID profile.
You can configure multiple SSID profiles, and have all of them active at any one time.
You can assign different wireless and security settings to each SSID profile. This allows you to
compartmentalize groups of users, set varying access privileges, and prioritize network traffic to and
from certain BSSs.
To the wireless clients in the network, each SSID appears to be a different access point. As in any wireless
network, clients can associate only with the SSIDs for which they have the correct security settings.
For example, you might want to set up a wireless network in your office where Internet telephony (VoIP)
users have priority. You also want a regular wireless network for standard users, as well as a ‘guest’
wireless network for visitors. In the following figure, VoIP_SSID users have QoS priority, SSID01 is the wireless
network for standard users, and Guest_SSID is the wireless network for guest users. In this example, the
guest user is forbidden access to the wired Land Area Network (LAN) behind the AP and can access
only the Internet.
NWA1000 Series User’s Guide
13
Figure 1 Multiple BSSs
Chapter 1 Introduction
1.2.2 Dual-Radio
Some of the NWA1000 Series models are equipped with dual wireless radios. This means you can
configure two different wireless networks to operate simultaneously.
Note: A different channel should be configured for each WLAN interface to reduce the
effects of radio interference.
You could use the 2.4 GHz band for regular Internet surfing and downloading while using the 5 GHz
band for time sensitive traffic like high-definition video, music, and gaming.
NWA1000 Series User’s Guide
14
Figure 2 Dual-Radio Application
Chapter 1 Introduction
NWA1000 Series User’s Guide
15
Chapter 2 Management Modes
Management Modes
2.1 Management Mode
The NWA1000 Series is a hybrid access point, which means it can work either in standalone mode or in
Nebula Cloud Management Mode (cloud mode).
Standalone
By default, the NWA1000 Series serves as a normal AP and is to be configured using its built-in web
configurator or CLI (Command Line Interface), See Chapter 4 on page 31 for detailed information
about the web configurator screens.
CHAPTER 2
Nebula Cloud Management
In this mode, you can manage and monitor the NWA1000 Series through the Zyxel Nebula cloud-based
network management system. See the NCC (Nebula Control Center) User’s Guide for how to configure
Nebula managed devices. See Chapter 23 on page 191 if you want to change the NWA1000 Series’s
VLAN setting or manually set its IP address.
2.1.1 Mode Changing
This section describes how to change the NWA1000 Series’s management mode.
From Standalone to Cloud
To manage your NWA1000 Series via the Zyxel NCC, connect the NWA1000 Series to the Internet and
register it to a site and organization in the NCC (http://nebula.zyxel.com) first using its serial number and
MAC address or its QR code. The serial number, MAC address and QR code can be found in the web
configurator dashboard or the label on the device. See the corresponding Quick Start Guide for how to
do hardware connections and device registration.
Note: The NWA1000 Series automatically goes into cloud mode after it can access the NCC
through the specified proxy server (if any) and is successfully registered in the NCC. Its
login password and wireless settings are then overwritten with what you have
configured in the NCC.
From Cloud to Standalone
To return to the default standalone mode, just click Unregister to remove the NWA1000 Series from the
organization/site in the NCC. The NWA1000 Series will reboot and restore the factory default settings.
NWA1000 Series User’s Guide
16
Chapter 2 Management Modes
2.2 Standalone AP Roles
Depending on your network setup, your NWA1000 Series in standalone mode can adopt the following
roles.
2.2.1 Root AP
The NWA1000 Series (Z) can act as the root AP in a wireless network and also allow repeaters (X and Y)
to extend the range of its wireless network at the same time. In the figure below, both clients A, B and C
can access the wired network through the root AP.
Figure 3 Root AP Application
On the NWA1000 Series in Root AP mode, you can have multiple SSIDs active for regular wireless
connections and one SSID for the connection with a repeater (repeater SSID). Wireless clients can use
either SSID to associate with the NWA1000 Series in Root AP mode. A repeater must use the repeater
SSID to connect to the NWA1000 Series in Root AP mode.
When the NWA1000 Series is in Root AP mode, repeater security between the NWA1000 Series and other
repeater is independent of the security between the wireless clients and the AP or repeater. When
repeater security is enabled, both APs and repeaters must use the same pre-shared key. See Section
10.2 on page 79 and Section 13.2 on page 117 for more details.
Unless specified, the term “security settings” refers to the traffic between the wireless clients and the AP.
At the time of writing, repeater security is compatible with the NWA1000 Series only.
NWA1000 Series User’s Guide
17
2.2.2 Repeater
The NWA1000 Series can act as a wireless network repeater to extend a root AP’s wireless network
range, and also establish wireless connections with wireless clients.
Using Repeater mode, your NWA1000 Series can extend the range of the WLAN. In the figure below, the
NWA1000 Series in Repeater mode (Z) has a wireless connection to the NWA1000 Series in Root AP mode
(X) which is connected to a wired network and also has a wireless connection to another NWA1000
Series in Repeater mode (Y) at the same time. Z and Y act as repeaters that forward traffic between
associated wireless clients and the wired LAN. Clients A and B access the AP and the wired network
behind the AP through repeaters Z and Y.
Figure 4 Repeater Application
Chapter 2 Management Modes
When the NWA1000 Series is in Repeater mode, repeater security between the NWA1000 Series and
other repeater is independent of the security between the wireless clients and the AP or repeater. When
repeater security is enabled, both APs and repeaters must use the same pre-shared key. See Section
10.2 on page 79 and Section 13.2 on page 117 for more details.
Once the security settings of peer sides match one another, the connection between devices is made.
At the time of writing, repeater security is compatible with the NWA1000 Series only.
NWA1000 Series User’s Guide
18
Chapter 3 Hardware
See your Quick Start Guide for information on making hardware connections.
3.1 Standalone Mode LEDs
The LEDs of your NWA1000 Series can be controlled by using the Suppression feature such that the LEDs
stay lit (ON) or OFF after the device is ready.
Following are LED descriptions for the NWA1000 Series series models in standalone mode.
CHAPTER 3
Hardware
3.1.1 NWA1123-AC PRO
The LEDs will stay ON when the NWA1123-AC PRO is ready. You can change this setting in the
Maintenance > LEDs > Suppression screen.
Figure 5 NWA1123-AC PRO LEDs
NWA1000 Series User’s Guide
19
Chapter 3 Hardware
The following table describes the LEDs.
Table 2 NWA1123-AC PRO LEDs
LEDCOLORSTATUSDESCRIPTION
PWR/SYS RedSlow Blinking (On for 1
GreenOn
GreenOnThe NWA1000 Series is ready for use.
RedOnThere is system error and the NWA1000 Series cannot
RedFast Blinking (On for 50
Red Slow Blinking (Blink for 3
GreenSlow Blinking (On for 1
ManagementGreen/
Amber
WLANGreenOnThe antenna switch is set to “Ceiling” for the radio.
AmberOnThe antenna switch is set to “Wall” for the radio.
sec, Off for 1 sec)
ms, Off for 50 ms)
times, Off for 3 sec)
sec, Off for 1 sec)
OffThe NWA1000 Series is in standalone mode.
The LED blinks orange and green alternatively when the
NWA1000 Series is booting up.
boot up, or the NWA1000 Series suffered a system failure.
The NWA1000 Series is doing firmware upgrade.
The Uplink port is disconnected.
The wireless module of the NWA1000 Series is disabled or
failed.
The 2.4 GHz WLAN is active.
The 2.4 GHz WLAN is active.
OffThe 2.4 GHz WLAN is not active.
WLANGreenOnThe antenna switch is set to “Ceiling” for the radio.
The 5 GHz WLAN is active.
AmberOnThe antenna switch is set to “Wall” for the radio.
The 5 GHz WLAN is active.
OffThe 5 GHz WLAN is not active.
UPLINKAmber/
Green
LANAmber/
Green
LocatorWhiteBlinkingThe Locator is activated and will show the actual location
OnAmber - The port is operating as a 100-Mbps connection.
Green - The port is operating as a Gigabit connection
(1000 Mbps).
BlinkingThe NWA1000 Series is sending/receiving data through
the port.
OffThe port is not connected.
OnAmber - The port is operating as a 100-Mbps connection.
Green - The port is operating as a Gigabit connection
(1000 Mbps).
BlinkingThe LAN port is sending/receiving data through the port.
OffThe LAN port is not connected.
of the NWA1000 Series between several devices in the
network.
OffThe Locator function is off.
NWA1000 Series User’s Guide
20
3.1.2 NWA1123-ACv2
The following are the LED descriptions for your NWA1123-ACv2.
Figure 6 NWA1123-ACv2 LED
Chapter 3 Hardware
The following are the LED descriptions for your NWA1000 Series.
Table 3 NWA1123-ACv2 LED
COLORSTATUSDESCRIPTION
AmberBlinks amber for 1
Green
GreenSteady OnThe NWA1000 Series is ready for use and its wireless interface is
RedSteady OnThe NWA1000 Series failed to boot up or is experience system failure.
second and green for
1 second alternatively.
Slow Blinking (On for 1
sec, Off for 1 sec)
Fast Blinking (On for 50
ms, Off for 50 ms)
Slow Blinking (Blink for
3 times, Off for 3 sec)
3.1.3 NWA1123-AC HD
The following are the LED descriptions for your NWA1123-AC HD.
The LED blinks orange and green alternatively when the NWA1000
Series is booting up.
activated.
The wireless module of the NWA1000 Series is disabled or failed.
The NWA1000 Series is undergoing firmware upgrade.
The Uplink port is disconnected.
NWA1000 Series User’s Guide
21
Chapter 3 Hardware
Figure 7 NWA1123-AC HD LED
The following are the LED descriptions for your NWA1000 Series.
Table 4 NWA1123-AC HD LED
COLORSTATUSDESCRIPTION
AmberBlinks amber for 1 second
Green
GreenSlow Blinking (On for 1
GreenSteady OnThe NWA1000 Series is ready for use, the NWA1000 Series’s
AmberSteady OnThe NWA1000 Series is ready for use, the NWA1000 Series’s
Bright BlueSteady OnThe NWA1000 Series’s wireless interface is activated, but there
WhiteSteady OnThe NWA1000 Series’s wireless interface is activated, but there
BlueSlow Blinking (Blink for 1
RedOnThe NWA1000 Series failed to boot up or is experience system
and green for 1 second
alternatively.
second, Off for 1 second)
time, Off for 1 second)
Fast Blinking (On for 50
milliseconds, Off for 50
milliseconds)
Slow Blinking (Blink for 3
times, Off for 3 seconds)
The NWA1000 Series is booting up.
The wireless module of the NWA1000 Series is disabled or fails,
the NWA1000 Series is using default wireless settings.
wireless interface is activated, and/or wireless clients are
connected to the NWA1000 Series when it receives power
using IEEE 802.3at PoE plus (full power mode).
wireless interface is activated, and/or wireless clients are
connected to the NWA1000 Series when it receives power
using 802.3af PoE (limited power mode).
are no wireless clients connected when it receives power
using IEEE 802.3at PoE plus (full power mode).
are no wireless clients connected when it receives power
using 802.3af PoE (limited power mode).
The NWA1000 Series is performing a Channel Availability
Check (CAC) with Dynamic Frequency Selection (DFS) to
monitor a channel for radar signals.
failure.
The NWA1000 Series is undergoing firmware upgrade.
The Uplink port of the NWA1000 Series is disconnected.
NWA1000 Series User’s Guide
22
3.1.4 NWA1302-AC
By default, the LEDs automatically turn on when the NWA1302-AC is ready. If the Suppression On option
is selected in the LEDs > Suppression screen (see Section 19.2 on page 183) to turn off the LEDs, you can
press the LED ON button for one second to turn on the LEDs again. The LEDs will blink and turn off after
two minutes.
Figure 8 NWA1302-AC LEDs
Chapter 3 Hardware
The following table describes the LEDs.
Table 5 NWA1302-AC LEDs
LEDCOLORSTATUSDESCRIPTION
PWR/SYS RedSlow Blinking (On for 1
GreenOn
GreenOnThe NWA1000 Series is ready for use.
RedOnThere is system error and the NWA1000 Series cannot
ManagementGreen/
Amber
UPLINKAmber/
Green
WLANGreenOnThe 2.4 GHz WLAN is active.
sec, Off for 1 sec)
Slow Blinking (On for 1
sec, Off for 1 sec)
Fast Blinking (On for 50
ms, Off for 50 ms)
Slow Blinking (Blink for 3
times, Off for 3 sec)
OffThe NWA1000 Series is in standalone mode.
OnAmber - The port is operating as a 10/100-Mbps
BlinkingThe NWA1000 Series is sending/receiving data through
OffThe port is not connected.
OffThe 2.4 GHz WLAN is not active.
The LED blinks orange and green alternatively when the
NWA1000 Series is booting up.
The wireless module of the NWA1000 Series is disabled or
failed.
boot up, or the NWA1000 Series suffered a system failure.
The NWA1000 Series is doing firmware upgrade.
The Uplink port is disconnected.
connection.
Green - The port is operating as a Gigabit connection
(1000 Mbps).
the port.
NWA1000 Series User’s Guide
23
Chapter 3 Hardware
Table 5 NWA1302-AC LEDs (continued)
LEDCOLORSTATUSDESCRIPTION
WLANGreenOnThe 5 GHz WLAN is active.
OffThe 5 GHz WLAN is not active.
LANAmber/
Green
3.2 Cloud Mode LEDs
Following are LED descriptions for the NWA1000 Series series models in cloud mode.
3.2.1 NWA1123-AC PRO
The LEDs will stay ON when the NWA1123-AC PRO is ready. You can change this setting through the
NCC (Nebula Control Center).
Figure 9 NWA1123-AC PRO LEDs
OnAmber - The port is operating as a 10/100-Mbps
connection.
Green - The port is operating as a Gigabit connection
(1000 Mbps).
BlinkingThe LAN port is sending/receiving data through the port.
OffThe LAN port is not connected.
NWA1000 Series User’s Guide
24
Chapter 3 Hardware
The following table describes the LEDs.
Table 6 NWA1123-AC PRO LEDs
LEDCOLORSTATUSDESCRIPTION
PWR/SYS RedSlow Blinking (On for 1
sec, Off for 1 sec)
GreenOn
GreenOnThe NWA1000 Series is ready for use.
Slow Blinking (On for 1
sec, Off for 1 sec)
RedOnThere is a system error and the NWA1000 Series cannot boot
Fast Blinking (On for 50
ms, Off for 50 ms)
Slow Blinking (Blink for 3
times, Off for 3 sec)
ManagementGreenOnThe NWA1000 Series is managed by the NCC.
Slow Blinking (On for 1
sec, Off for 1 sec)
AmberSlow Blinking (On for 1
sec, Off for 1 sec)
WLANGreenOnThe antenna switch is set to “Ceiling” for the radio.
AmberOnThe antenna switch is set to “Wall” for the radio.
OffThe 2.4 GHz WLAN is not active.
WLANGreenOnThe antenna switch is set to “Ceiling” for the radio.
The LED blinks orange and green alternatively when the
NWA1000 Series is booting up.
The wireless module of the NWA1000 Series is disabled or
failed.
up, or the NWA1000 Series suffered a system failure.
The NWA1000 Series is undergoing firmware upgrade.
The Uplink port is disconnected.
The NWA1000 Series is connected to the NCC, but not
registered.
The NWA1000 Series is searching for (discovering) the NCC.
The 2.4 GHz WLAN is active.
The 2.4 GHz WLAN is active.
The 5 GHz WLAN is active.
AmberOnThe antenna switch is set to “Wall” for the radio.
The 5 GHz WLAN is active.
OffThe 5 GHz WLAN is not active.
UPLINKAmber/
Green
LANAmber/
Green
LocatorWhiteBlinkingThe Locator is activated and will show the actual location
OnAmber - The port is operating as a 100-Mbps connection.
Green - The port is operating as a Gigabit connection (1000
Mbps).
BlinkingThe NWA1000 Series is sending/receiving data through the
port.
OffThe port is not connected.
OnAmber - The port is operating as a 100-Mbps connection.
Green - The port is operating as a Gigabit connection (1000
Mbps).
BlinkingThe LAN port is sending/receiving data through the port.
OffThe LAN port is not connected.
of the NWA1000 Series between several devices in the
network.
OffThe Locator function is off.
NWA1000 Series User’s Guide
25
3.2.2 NWA1123-ACv2
The following are the LED descriptions for your NWA1123-ACv2.
Figure 10 NWA1123-ACv2 LED
Chapter 3 Hardware
The following are the LED descriptions for your NWA1123-ACv2.
Table 7 NWA1123-ACv2 LED
COLORSTATUSDESCRIPTION
AmberBlinks amber for 1
Green
AmberBlinks amber and
Green
GreenOnThe NWA1000 Series is ready for use and its wireless interface is
RedOnThe NWA1000 Series failed to boot up or is experience system failure.
second and green for
1 second alternatively.
green alternatively 3
times and then turns
solid green for 3
seconds.
Slow Blinking (On for 1
sec, Off for 1 sec)
Fast Blinking (On for 50
ms, Off for 50 ms)
3.2.3 NWA1123-AC HD
The following are the LED descriptions for your NWA1123-AC HD.
The LED blinks orange and green alternatively when the NWA1000
Series is booting up.
The NWA1000 Series is discovering the NCC.
activated.
The wireless module of the NWA1000 Series is disabled or failed, or
the NWA1000 Series is connected to the NCC, but not registered.
The NWA1000 Series is undergoing firmware upgrade.
NWA1000 Series User’s Guide
26
Chapter 3 Hardware
Figure 11 NWA1123-AC HD LED
The following are the LED descriptions for your NWA1123-AC HD.
Table 8 NWA1123-AC HD LED
COLORSTATUSDESCRIPTION
AmberBlinks amber for 1 second
Green
AmberBlinks amber and green
Green
GreenSlow Blinking (On for 1
GreenSteady OnThe NWA1000 Series is ready for use, the NWA1000 Series’s
AmberSteady OnThe NWA1000 Series is ready for use, the NWA1000 Series’s
Bright BlueSteady OnThe NWA1000 Series’s wireless interface is activated, but there
WhiteSteady OnThe NWA1000 Series’s wireless interface is activated, but there
BlueSlow Blinking (Blink for 1
RedOnThe NWA1000 Series failed to boot up or is experience system
and green for 1 second
alternatively.
alternatively 3 times and
then turns solid green for 3
seconds.
second, Off for 1 second)
time, Off for 1 second)
Fast Blinking (On for 50
milliseconds, Off for 50
milliseconds)
The NWA1000 Series is booting up.
The NWA1000 Series is discovering the NCC.
The wireless module of the NWA1000 Series is disabled or fails,
the NWA1000 Series is in cloud mode but not registered with
the NCC.
wireless interface is activated, and/or wireless clients are
connected to the NWA1000 Series when it receives power
using IEEE 802.3at PoE plus (full power mode).
wireless interface is activated, and/or wireless clients are
connected to the NWA1000 Series when it receives power
using 802.3af PoE (limited power mode).
are no wireless clients connected when it receives power
using IEEE 802.3at PoE plus (full power mode).
are no wireless clients connected when it receives power
using 802.3af PoE (limited power mode).
The NWA1000 Series is performing a Channel Availability
Check (CAC) with Dynamic Frequency Selection (DFS) to
monitor a channel for radar signals.
failure.
The NWA1000 Series is undergoing firmware upgrade.
NWA1000 Series User’s Guide
27
3.2.4 NWA1302-AC
By default, the LEDs automatically turn on when the NWA1302-AC is ready. If the LEDs are turned off by
the NCC, you can press the LED ON button for one second to turn on the LEDs again. The LEDs will blink
and turn off after two minutes.
Figure 12 MWA1302-AC LEDs
Chapter 3 Hardware
The following table describes the LEDs.
Table 9 NWA1302-AC LEDs
LEDCOLORSTATUSDESCRIPTION
PWR/SYS RedSlow Blinking (On for 1
sec, Off for 1 sec)
GreenOn
GreenOnThe NWA1000 Series is ready for use.
Slow Blinking (On for 1
sec, Off for 1 sec)
RedOnThere is a system error and the NWA1000 Series cannot
Fast Blinking (On for 50
ms, Off for 50 ms)
Slow Blinking (Blink for 3
times, Off for 3 sec)
ManagementGreenOnThe NWA1000 Series is managed by the NCC.
Slow Blinking (On for 1
sec, Off for 1 sec)
AmberSlow Blinking (On for 1
UPLINKAmber/
Green
sec, Off for 1sec)
OnAmber - The port is operating as a 10/100-Mbps
BlinkingThe NWA1000 Series is sending/receiving data through
OffThe port is not connected.
The LED blinks orange and green alternatively when the
NWA1000 Series is booting up.
The wireless module of the NWA1000 Series is disabled or
failed.
boot up, or the NWA1000 Series suffered a system failure.
The NWA1000 Series is doing firmware upgrade.
The Uplink port is disconnected.
The NWA1000 Series is connected to the NCC, but not
registered.
The NWA1000 Series is searching for (discovering) the
NCC.
connection.
Green - The port is operating as a Gigabit connection
(1000 Mbps).
the port.
NWA1000 Series User’s Guide
28
Chapter 3 Hardware
Table 9 NWA1302-AC LEDs (continued)
LEDCOLORSTATUSDESCRIPTION
WLANGreenOnThe 2.4 GHz WLAN is active.
OffThe 2.4 GHz WLAN is not active.
WLANGreenOnThe 5 GHz WLAN is active.
OffThe 5 GHz WLAN is not active.
LANAmber/
Green
OnAmber - The port is operating as a 10/100-Mbps
connection.
Green - The port is operating as a Gigabit connection
(1000 Mbps).
BlinkingThe LAN port is sending/receiving data through the port.
OffThe LAN port is not connected.
NWA1000 Series User’s Guide
29
PART I
Standalone
Configuration
30
Loading...
+ 233 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.