Whirlpool 7MWTW1504DQ0, 7MWTW1905DW0, 7MWTW1805DM0, 7MWTW1709DM0, 7MWTW1604DM0 Use And Care Manual

...

0 (0)

Whir

TOP-LOADING

WASHER

USE AND CARE GUIDE

Para una versi6n de estas instrucciones en espa_ol, visite www.whirlpool.com

Table of Contents

WASHER SAFETY ......................................................... 2

WHAT'S NEW UNDER THE LID? ................................. 3

CONTROL PANEL AND FEATURES ............................ 4

CYCLE GUIDE ............................................................... 5

USING YOUR WASHER ................................................ 6

WASHER MAINTENANCE ............................................ 8

TROUBLESHOOTING ................................................. 10

WARRANTY ................................................................. 14

ASSISTANCE OR SERVICE ........................ Back Cover

LAVEUSE A CHARGEMENT

PAR LE DESSUS

GUIDE D'UTILISATION ET

D'ENTRETIEN

Table des matibres

Si_CURIT¢: DE LA LAVEUSE ...................................... 15

QUOI DE NEUF SOUS LE COUVERCLE? ................. 16

TABLEAU DE COMMANDE ET

CARACTC:RISTIQUES ................................................. 17

GUIDE DE PROGRAMMES ........................................ 19

UTILISATION DE LA LAVEUSE .................................. 20

ENTRETIEN DE LA LAVEUSE .................................... 23

DI_PANNAGE ............................................................... 25

GARANTIE ................................................................... 30

ASSISTANCE OU SERVICE ............ Couverture artiste

W10560163B W10560164A=SP

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING." These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,

including the following:

[] Read all instructions before using the washer. [] Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or explode.

[] Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water. These substances give off vapors that could ignite or

explode.

[] Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been used for such a period, before using the washing

machine, turn on all hot water faucets and let the water flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during

this time.

SAVE THESE INSTRUCTIONS

Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used

near children.

Before the washer is removed from service or discarded,

remove the door or lid.

[] Do not reach into the washer if the drum, tub or agitator is

moving.

[] Do not install or store the washer where it will be exposed to

the weather.

[] Do not tamper with controls. [] Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in

published user-repair instructions that you understand and have the skills to carry out.

[] See "Electrical Requirements" located in the installation

instructions for grounding instructions.

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

WHAT'S NEW UNDER THE LID?

Your new washer will operate differently than your past agitator-style washer.

Lid Lock _lll Sounds

To allow for higher spin speeds, the lid will lock and the Lid Locked light will turn on. When this light is

lit, the lid is locked and cannot be opened. When this light is blinking, the washer is paused. When this light is off, the lid can be opened. After a cycle

is started, water will enter washer and then lock. If you need to open the lid to add a garment after this

point, you must press START/Pause and wait for the

lid to unlock. The lid will only unlock after washer

movement has stopped. Depending on when in the

cycle you try to pause, it may take several seconds to several minutes for the lid to unlock. Press START/

Pause to resume the cycle.

Sensing

This washer will perform a series of spins to check for load balance. During this time, a series of clicks and a whirring noise signal that sensing technology

is determining if there is an off-balance load.

iMPORTANT:

• After the washer basket fills to the selected water level, the lid must be closed before the wash cycle can start.

If filling stops with the lid open, close lid and press START button.

• Rinse option must be selected to 1 Rinse with Softener or 2 Rinses with Softener to ensure fabric softener dispenses at the correct time.

At different stages of the wash cycle, you may

hear sounds and pauses that are different from

those of your previous washer. For example, you

may hear a clicking and hum at the beginning of the cycle as the lid lock goes through a self-test. There will be different kinds of humming and whirring sounds as the agitator tests for load

balance or moves the load. And, sometimes, you may hear nothing at all as the washer allows

time for clothes to soak.

Spray Rinse

Select cycles default to a spray rinse. During these cycles, you will hear water enter the washer as the

tub spins, allowing the rinse water to penetrate clothes. Check the "Cycle Guide" for details.

CONTROL PANEL AND FEATURES

Not all features and options are available on all models.

LOAD SiZE

Select the setting most suitable for your load. Small will add a low amount of water for smaller loads and Ex

Large will add the most amount of water for large or bulky loads. Items need to move freely. Tightly packing can lead to

poor cleaning performance and may increase wrinkling and tangling.

O WASH TEMP

Wash Temp senses and maintains uniform water temperatures by regulating incoming hot and cold water.

Select a wash temperature based on the type of fabric and soils being washed. For best results and following

the garment label instructions, use the warmest wash water safe for your fabric.

• On some models and cycles, warm and hot water may be cooler than your previous washer.

• Even in a cold and cool water wash, some warm water

may be added to the washer to maintain a minimum temperature.

WASH CYCLE KNOB Use the Wash Cycle knob to select cycles on your washer. Knob does not advance during the progress of the cycle, see cycle status lights for each stage of the process. See

"Cycle Guide" for detailed descriptions of cycles.

RINSE OPTIONS The following options may be added to most cycle.

See "Cycle Guide" for additional details.

1 RINSE

This option is used to limit a cycle to one rinse. 2 RINSES

This option can be used to automatically add a second rinse to most cycles.

1 RINSE with SOFTENER

This option must be selected if using fabric softener during a cycle. It ensures that fabric softener is added

at the correct time in the rinse for even distribution.

2 RINSES with SOFTENER

This option turns on both the Fabric Softener and the 2 Rinses option.

Appearance may vary.

START/PAUSE BUTTON

Press to start the selected cycle; press again to pause the cycle and unlock the lid. Press and hold for 3 seconds

to cancel a cycle. NOTE: if the washer is spinning, it may take several

minutes to unlock the lid. CYCLE STATUS LIGHTS iNDiCATOR

Progress C_) C_) ([_) C_ Q C_

The Cycle Status Lights show the progress of a cycle. At each stage of the process, you may notice sounds or

pauses that are different from traditional washers.

Fitl Wash Rinse Spin Done Locked

FILL When the START/Pause button is pressed, the washer will

fill to the selected water level. If the lid is closed when the washer is done filling the lid will lock and the washer will

begin operation. If the lid is open when the water stops entering the

washer, the cycle will not begin until the lid has been closed and the START/Pause button is pressed. If the

cycle has not been started within 10 minutes of the water filling the washer, the washer will pump out the water.

NOTE: Avoid opening lid during sensing phase. The sensing process will start over when the washer is restarted. The FILL light may also come on during the

Soak and Wash portions of the cycle. This is normal. To restart the washer after the lid has been opened press

START. WASH

You will hear the agitator moving the load. The motor sounds may change at different stages in the cycle.

The wash time is determined by the selected soil level. RINSE

You will hear sounds similar to the wash cycle as the washer rinses and moves the load. You may hear the

motor turning on briefly (short hum) to move the basket while filling. Fabric softener will be added if the 1 Rinse

with Softener or 2 Rinses with Softener option was selected.

Some cycles use spray rinsing. After draining and spinning out wash water, the washer will continue to

spin and spray in rinse water for the entire rinse time.

SPiN

The washer spins the load at increasing speeds for proper water removal, based on the selected cycle

and spin speed.

DONE

Once the cycle is complete, this light will come on. Remove the load promptly for best results.

CYCLE GUIDE

For best fabric care, choose the cycle that best fits the load being washed. Not all cycles and options are available on all models.

LiD LOCKED

To allow for higher spin speeds, the lid will lock and the Lid Locked light

will turn on. When this light is lit, the lid is locked and cannot be opened.

When this light is blinking, the washer is paused. When this light is off, the lid

can be opened. If you need to open the lid, press

START/Pause. The lid will unlock once the washer movement has stopped.

This may take several minutes if the load was spinning at high speed.

Press START/Pause again to resume the cycle.

CZD

Locked

Cottons, linens, and mixed garment

loads

Cottons, linens, and mixed garment

loads

Cottons, linens, and mixed garment

loads

No-iron fabrics, cottons, perm

press, linens,

synthetics

No-iron fabrics, cottons, perm

press, linens,

synthetics

Machine-wash

silks, hand-washed fabrics

Hand-washed garments or

dripping wet items

Swimsuits and items requiring

rinsing without detergent

No clothes in

washer

NOTE: If you are using fabric softener, be sure to select the *All rinses are cold.

Normal Light

Normal

Normal Heavy

Casual

Regular

Casual

Light

Delicate

Drain &

Spin

Rinse &

Spin

Clean Washer

with

affresh <e

Hot

Warm

Cool Cold

Tap Cold

Hot

Warm

Cool Cold

Tap Cold

Hot

Warm

Cool Cold

Tap Cold

Hot

Warm

Cool Cold

Tap Cold

Hot

Warm

Cool Cold

Tap Cold

Hot

Warm

Cool Cold

Tap Cold

N/A

Cold rinse only

Hot

Warm

Cool Cold

Tab Cold

High

Low

High

Low

Rinse with

Use this cycle for lightly soiled mixed loads. This cycle features a spray rinse.

Use this cycle for normally soiled cottons and mixed fabric loads. This cycle features a spray rinse.

Use this cycle for heavily soiled or sturdy items. This cycle features a spray rinse. Use this cycle for cleaning the interior

of the washer. See "Washer Care."

Use this cycle to wash loads of no-iron fabrics such as sport shirts, blouses, casual business clothes, permanent

press, and blends.

Use this cycle to wash lightly-soiled loads of no-iron fabrics such as sport shirts, blouses, casual business clothes, permanent press, and blends.

Use this cycle to wash lightly soiled garments indicating "Machine Washable Silks" or "Gentle" cycle on the care label. Place small items in mesh garment bags before wash- ing. This cycle features a spray rinse.

This cycle uses a spin to shorten drying times for heavy fabrics or special-care items washed by hand. Use this cycle to drain washer after cancelling a cycle or completing a cycle after a power failure.

Combines a rinse and high speed spin for loads requiring an additional rinse cycle or to complete a load after power interruption. Also use for loads that require rinsing only.

Use this cycle every 30 washes to keep the inside of your washer fresh and clean. This cycle uses a higher water level.

Use with affresh _*_Washer Cleaner tablet or liquid chlorine bleach to thoroughly clean the inside of your washer. This

cycle should not be interrupted. See "Washer Care." iMPORTANT: Do not place garments or other items in the

washer during the Clean Washer with affresh _'_)cycle. Use this cycle with an empty wash tub.

Softener or 2 Rinses with Softener option.

USING YOUR WASHER

Fire Hazard

Never place items in the washer that are dampened with gasoline or other flammable fluids,

No washer can completely remove oil, Do not dry anything that has ever had any type of oil on

it (including cooking oils). Doing so can result in death, explosion, or fire.

Sort and prepare your laundry

* Empty pockets. Loose change, buttons, or any small object

can pass under the agitator and become trapped, causing unexpected sounds.

, Sort items by recommended cycle, water temperature,

and colorfastness.

* Separate heavily soiled items from lightly soiled. = Separate delicate items from sturdy fabrics.

= Do not dry garments if stains remain after washing, because

heat can set stains into fabric.

* Treat stains promptly. = Close zippers, fasten hooks, tie strings and sashes, and

remove non-washable trim and ornaments.

= Mend rips and tears to avoid further damage to items

during washing.

Helpful Tips: * When washing water-proof or water-resistant items, load

evenly.

= Use mesh garment bags to help avoid tangling when washing

delicate or small items.

,, Turn knits inside out to avoid pilling. Separate lint-takers from

lint-givers. Synthetics, knits, and corduroy fabrics will pick up lint from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care label instructions to avoid damage to your garments.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Add laundry products

Add a measured of amount of detergent or single-dose laundry packet into the basket.

If using Oxi-type boosters, color-safe bleach, or fabric softener crystals, add to the bottom of the washer basket

before adding clothes. NOTE: Follow the manufacturer's instructions to determine

the amount of laundry products to use.

3= Load laundry into washer

Load garments in loose heaps evenly around basket wall. For best results, do

not pack the load tightly. Do not wrap large items such as sheets around the agitator; load them in loose piles around

the sides of the basket. Try mixing different sized items to reduce tangling.

IMPORTANT: Do not tightly pack or force items into washer. Items need to

move freely for best cleaning and to reduce wrinkling and tangling.

Add liquid chlorine bleach to dispenser

Add fabric softener to dispenser

(on some models}

Pour a measured amount of liquid fabric softener into dispenser; always follow

manufacturer's directions for correct amount of fabric softener based on your load size.

Dilute liquid fabric softener by filling the dispenser with warm water until liquid reaches the underside of the rim. See max fill

line arrows.

IMPORTANT: Rinse option must be selected .......

to 1 Rinse with Softener or 2 Rinses with Softener to ensure proper distribution of the

fabric softener during the final rinse portion of the cycle.

Adding Liquid Fabric Softener Manually to Wash Load

During the final rinse, wait until the washer has completed filling, press the START/Pause button to pause the washer.

Lift the lid and add the measured recommended amount of liquid fabric softener. Do not use more than the recommended

amount. Close the lid and press the START/Pause button again to start the washer.

RINSE OPTIONS

_f.....

Do not overfill, dilute, or use more than 1 cup (250 mL). Do not use color-safe bleach or Oxi products in the same cycle with liquid chlorine bleach.

f6= Select cycle

Normal

Light o Heavy

Regular

Casual

Drain & Spin o

Rinse & Spin o o Delicate

Clean Washer

with af_r_$ll

_ =

Turn cycle knob to choose your wash cycle. For more information, see "Cycle Guide".

o Light

7, Select LOAD SiZE

LOAD SiZE

E× Large o

Large o

Wash Temp Suggested Fabrics

Tap Cold This is the temperature from Dark colors that

your faucet, bleed or fade

Light soils

Medium o

Select the load size setting most suitable for your load. Small will add a low amount of water for smaller loads and Ex Large

will add the most amount of water for large or bulky loads. Items need to move freely.

8, Select WASH TEMP

WASH TEMP

Hot o

Cool o

Wam i!

Cold o

Tap Cold o

Once you select a cycle, select the desired wash temperature by turning the Wash Temp knob to the appropriate setting

based on your load. All rinses are tap cold. NOTE: Always read and follow fabric care label instructions

to avoid damage to your garments.

Wash Temp Suggested Fabrics

Hot Some cold water is added to save Whites and pastels

energy. This will be cooler than Durable garments

your hot water heater setting. Heaw soils

Warm

Some cold water will be added, so

this will be cooler than what your

previous washer provided.

Cool

Warm water may be added to

assist in soil removal and to help

Cold This is the temperature from your

faucet. If your tap cold water is very cold, warm water may be

added to assist in soil removal and help dissolve detergent.

Bright colors Moderate to light soils

Colors that bleed or fade

;: Dark colors that ;;::ibleed or fade

Light soils

fg. Select options, if desired

RINSE OPTIONS

o 1Rinse

o 2 Rinses

ol Rinse

with

softener

o 2 Rinses

with

so_ener

Select the desired cycle options. If you are using fabric softener, be sure to select one of the Fabric Softener options.

Press START/Pause

to begin wash cycle

Ho_d3 Seconds

Start/Pause

to Cancel

Press the START/Pause button to start the wash cycle. When the cycle has finished, the DONE indicator will light. Promptly remove garments after cycle has completed to avoid odor, reduce wrinkling, and rusting of metal hooks, zippers, and

snaps. Unlocking the lid to add garments

If you need to open the lid to add 1 or 2 missed garments: Press START/Pause; the lid will unlock once the

washer movement has stopped. This may take several minutes if the load was spinning at high speed. Then close

lid and press START/Pause again to restart the cycle. If lid is left open for more than 10 minutes, the water will pump

out automatically.

WASHER MAINTENANCE

f WATER INLET HOSES

Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if

bulges, kinks, cuts, wear, or leaks are found. When replacing your inlet hoses, mark the date of replacement

on the label with a permanent marker. NOTE: This washer does not include inlet hoses. See the

"Installation Instructions" for more information.

WASHER CARE

Recommendations to Help Keep Your Washer Clean and Performing at its Best

1. Always follow the detergent manufacturer's instructions regarding the amount of detergent to use. Never use more

than the recommended amount because that may increase the rate at which detergent and soil residue accumulate inside your washer, which in turn may result in undesirable odor.

2. Use warm and hot wash water settings sometimes (not exclusively cold water washes), because they do a better

job of controlling the rate at which soils and detergent accumulate.

3. Always leave the washer lid open between uses to help dry out the washer and prevent the buildup of odor-causing

residue.

Cleaning Your Top Loading Washer Read these instructions completely before beginning the

routine cleaning processes recommended below. This Washer Maintenance Procedure should be performed, at a minimum,

once per month or every 30 wash cycles, whichever occurs sooner, to control the rate at which soils and detergent may

otherwise accumulate in your washer. Cleaning the Inside of the Washer

To keep your washer odor-free, follow the usage instructions provided above, and use this recommended monthly cleaning

procedure: Recommended Cycle for Cleaning the Washer

Refer to the "Cycle Guide" for the optimal cycle for cleaning the inside of the washer. Use this cycle with affresh e_Washer

Cleaner or liquid chlorine bleach as described below. Begin procedure

1. afresh _ Washer Cleaner Cycle Procedure (Recommended for Best Performance):

a. Open the washer lid and remove any clothing or items. boPlace an affesh ®Washer Cleaner tablet in the bottom of

the washer basket.

coDo not place an affresh e_Washer Cleaner tablet in the

detergent dispenser.

doDo not add any detergent or other chemical to the washer

when following this procedure.

eoClose the washer lid. f. Select the cycle recommended for cleaning the inside of

the washer.

goPress the START/Pause/Unlock button to start the cycle.

NOTE: For best results, do not interrupt cycle. If cycle must be interrupted, press START/Pause/Unlock once or twice (depending on model). After the cycle has stopped, run a

RINSE & SPIN cycle to rinse cleaner from washer.

2. Chlorine Bleach Procedure (Alternative}:

a. Open the washer lid and remove any clothing or items. b. Add 1 cup (236 mL) of liquid chlorine bleach to the bleach

compartment.

NOTE: Use of more liquid chlorine bleach than is recommended above could cause washer damage over

time. coClose the washer lid. d. Do not add any detergent or other chemical to the washer

when following this procedure.

eoSelect the cycle recommended for cleaning the inside of

the washer.

f WASHER CARE (cont.) "_

fo Press the START/Pause/Unlock button to start the cycle. NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, press START/Pause/Unlock once or twice

(depending on model). After the cycle has stopped, run a

RINSE & SPIN cycle to rinse cleaner from washer. Cleaning the Dispensers After a period of using your washer, you may find some residue

buildup in the washer's dispensers. To remove residue from the dispensers, wipe them with a damp cloth and towel dry.

Do not attempt to remove the dispensers or trim for cleaning. The dispensers and trim are not removable. Ifyour model has

a dispenser drawer, however, remove the drawer and clean it before or after you run the Clean Washer cycle. Use an all-

purpose surface cleaner, if needed. Cleaning the Outside of the Washer

Use a soft, damp cloth or sponge to wipe away any spills. Use only mild soaps or cleaners when cleaning external washer

surfaces. IMPORTANT: To avoid damaging the washer's finish, do not

use abrasive products.

NON=USE AND VACATION CARE

Operate your washer only when you are home. If moving, or not using your washer for a period of time, follow these steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer, to avoid flooding due to water pressure surge.

f WINTER STORAGE CARE "_

IMPORTANT: To avoid damage, install and store washer where it will not freeze. Because some water may stay in

hoses, freezing can damage washer. If storing or moving during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water inlet hoses.

2. Put 1 qt. (1 L) of R._,L-type antifreeze in basket and run washer on RINSE & SPIN cycle for about 30 seconds

to mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

f TRANSPORTING YOUR WASHER

Shut off both water faucets. Disconnect and drain water inlet hoses.

If washer will be moved during freezing weather, follow Winter Storage Care directions before moving.

Disconnect drain hose from drain system and drain any remaining water into a pan or bucket. Disconnect drain

hose from back of washer.

Unplug power cord.

Place inlet hoses and drain hose inside washer basket.

Drape power cord over edge and into washer basket.

Place packing tray from original shipping materials back inside washer, if you do not have packing tray, place heavy

blankets or towels into basket opening. Close lid and place tape over lid and down front of washer. Keep lid taped until

washer is placed in new location.

RE! NSTALLING/USI NG WASHER AGAI N

To reinstall washer after non-use, vacation, winter storage, or moving:

1. Refer to "Installation Instructions" to locate, level, and connect washer.

2. Before using again, run washer through the following recommended procedure:

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet hoses. Turn on both water faucets.

TROUBLESHOOTING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

2. Plug in washer or reconnect power.

3. Run washer through Casual Regular cycle to clean washer and remove antifreeze, if used. Use half the manufacturer's

recommended amount of detergent for a medium-size load.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

if you experience | Possible Causes _ Solution

Check the following for Front and rear feet must be in firm contact with floor, and

proper installation or washer must be level to operate properly.

see "Using Your Washer" section.

Clicking or metallic

noises

Gurgling or humming

Humming

J !

Feet may not be in contact with the

floor and locked. Washer may not be level.

Load could be unbalanced.

Objects caught in washer drain system.

Washer may be draining water.

Load sensing may be occurring.

Check floor for flexing or sagging. If flooring is uneven, a 3/4" (19 mm) piece of plywood under your washer will reduce sound.

See "Level the Washer" in installation instructions. Load dry items in loose heaps evenly around basket wall.

Adding wet items to washer or adding more water to basket could unbalance washer.

Wash smaller loads to reduce imbalance. Do not tightly pack. Avoid washing single items.

Use Normal cycle and Ex Large or Large load size for oversized, non-absorbent items such as comforters or poly-filled jackets.

See "Cycle Guide" and "Using Your Washer" in this Use and Care Guide.

Empty pockets before washing. Loose items such as coins could fall between basket and tub or may block pump. It may be necessary to call for service to remove items.

It is normal to hear metal items on clothing such as metal snaps, buckles, or zippers touch against the basket.

It is normal to hear the pump making a continuous humming sound with periodic gurgling or surging as final amounts of

water are removed during the Drain & Spin cycles. You may hear the hum of the sensing spins after you have

started the washer. This is normal.

Check the following for Water may splash off basket if washer is not level. Check that

proper installation: load is not unbalanced or tightly packed.

Washer not level.

Fill hoses not attached tightly.

Tighten fill-hose connection.

+ 22 hidden pages