WELLTECH LAN Phone 201 User Manual
L
L
A
A
N
N
P
P
h
hoo
n
nee110011//220011
U
Usseerr
M
Maa
n
n
u
uaall
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
1
Chapter 1 Introduction .........................................................................................................................3
＊Product Description..................................................................................................................4
1.Features and Specification ................................................................................................4
2.Appearance........................................................................................................................7
Chapter 2 Operating Procedure – LCD Display Configuration......................................................... 11
1.Initialize LAN Phone 101/201 ................................................................................................ 11
2.LCD Configuration .................................................................................................................12
Chapter 3 Advanced Configurations via Telnet ................................................................................. 19
1. [help] command .....................................................................................................................19
2. [quit] command ...................................................................................................................... 20
3. [reboot] command .................................................................................................................. 20
4. [flash] command ....................................................................................................................20
5. [commit] command ................................................................................................................ 21
6. [ifaddr] command................................................................................................................... 21
7. [time] command ..................................................................................................................... 22
8. [ping] command ..................................................................................................................... 22
9. [pbook] command ..................................................................................................................23
10.[ddns] command.................................................................................................................... 24
11.[pppoe] command..................................................................................................................25
12.[sysconf] command ............................................................................................................... 26
13. [h323] command ..................................................................................................................27
14. [voice] command..................................................................................................................29
15. [tos] command......................................................................................................................30
16. [tone] command ...................................................................................................................31
17. [support] command ..............................................................................................................32
18. [bureau] command ...............................................................................................................32
19.[rom] command..................................................................................................................... 33
20.[passwd] command ...............................................................................................................35
Chapter 4 Web Configuration .........................................................................................................36
Step 1. Browse the IP Address predefined via RS-232..............................................................36
Step 2. Input the login name and password................................................................................37
Step 3. The web interface main screen.......................................................................................37
Step 4. Start configure................................................................................................................ 38
1.Network Interface ...........................................................................................................38
2. H323 Information........................................................................................................... 40
3. System Configure........................................................................................................... 42
4. PPPoE Configure ...........................................................................................................43
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
2
Chapter 5 Upgrade the LAN Phone 101/201 .................................................................................. 55
＊Download Procedure..............................................................................................................55
1.LCD Panel Control..........................................................................................................55
2.Remote Control: Telnet ................................................................................................... 56
3.Web Management............................................................................................................57
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
3
Chapter 1 Introduction
The LAN Phone 101/201 is a full-featured IP-based telephone system, which provides VoIP service
on LAN or any IP based environment. By using IP environment for voice communication, company
or individual can save lots of expenses and make data and voice network converged.
LAN Phone 101/201 also supports PSTN analog line connection. Therefore, it can perform as the
same as traditional POTS (Plain Old Telephone Service).
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
4
＊Product Description
1.Features and Specification
Basic Features:
ITU-T H.323 v3 compliance
DTMF detection/generation
TFTP/FTP software download
Remote configuration/reset via Telnet
LED indication for system status：Speaker, Hold ,Mute , Message , PSTN
Network Interface :
- Switch Hub inside, providing 2 RJ-45 sockets for 10/100Base-T connection
- 1 RJ-11 socket for PSTN connection
Microsoft Net Meeting v3.0 compatible
SNTP (Simple Network Time Protocol)
Call HOLD/TRANSFER/FORWARD/MUTE
PSTN/IP side access switch
10 Direct Line Button for speed dial
Speaker Mode
System Configuration from keypads and displayed on LCD
Ring Tone selection
Password setting for security
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
5
Function Keys : Speaker , Redial , Mute , Hold , Transfer , Forward , Message , PSTN
Ten sets last Phone Number redial
Dial plan
Provide TOS(Type Of Service) function
GateKeeper mode or Peer to Peer mode selection
Caller ID:
IP side display H323-ID and E.164.
Display the count of total call received.
Display un-answered call name, number.
Show caller’s name, number, calling time.
Volume Adjustment:
Speaker volume level adjustable.
Handset Receiver volume level adjustable.
LCD:
2 lines, 24 character Dot Matrix display.
Indicator messages of HOLD, MUTE, PSTN, Directed Line 1~10.
Display current date and time.
Display of call duration.
Audio features:
Codec -- G.711 a/μlaw, G.723.1 (6.3Kbps),G.729, G.729a
VAD (Voice Activity Detection), CNG (Comfort Noise Generate)
G.168/165-compliant adaptive echo cancellation
Dynamic Jitter Buffer
Bad Frame Interpolation
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
6
Provide H.245 Out-band DTMF message
Call Transfer (H.450.2)
Call Forward (H.450.3)
Call Hold (H.450.4)
Gain (Voice Volume) Settings
Provide Call Progress Tone: Dial tone, busy tone, call-holding tone and ring-back tone
Firmware Upgrade:
Firmware version displayed on LCD.
Two ways to upgrade firmware:
- Download by KEYPAD configuration.
- Download by Telnet.
Management Features:
Two easy ways for system configuration
- TELNET
- LAN Phone 101/201 KEYPAD (can only upgrade application rom file)
- Web Browser
- Management Center(only simple configuration)
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
7
2.Appearance
1.Front View and Keypad function
C: Cancel and Clear
: Move to left /previous and right/next .
OK: Press OK to confirm the modification.
Direct Line (DL) Button 1 – 10: User press DL button to do speed dial according to phone
book data 1-10 (please refer to LCD configuration-Phone Address Book or Advanced
Configurations via Telnet-[pbook] command ).
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
8
Number 1 –10, * and #: The function is as the same as the general phone set.
Corresponding list of keypad and symbol:
1 “Space” ; “,” ; “.” ; “!” ; “1”
2 “A” ; “ B” ; “C” ; “2”
3 “D” ; “E” ; “F” ; “3”
4 “G” ; “H” ; “I” ; “4”
5 “J” ; “K” ; “L” ; “5”
6 “M” ; “N” ; “O” ; “6”
7 “P” ; “Q” ; “R” ; “S” ; “7”
8 “T” ; “U” ; “V” ; “8”
9 “W” ; “X” ; “Y” ; “Z” ; “9”
* “-“ ; “?” ; “*”
0 “0”
# “_” ; “@” ; “#”
MUTE: Mute the voice of MIC and let others can’t hear from user in communication.
PSTN: Press PSTN to switch LAN Phone 101/201 as PSTN or IP Phone Mode. In PSTN
mode, “PSTN” characters will be displayed on LCD left bottom side, then users can dial out as
if standard telephone set in PSTN ; in IP Phone mode , “GK” characters will be displayed on
LCD left bottom side.
Note:1. When LAN Phone is in PSTN mode, only PSTN and SPEAKER function key can work.
2. On LCD will display ”….Incoming Call…. ”
to notice user when LAN Phone has both IP
and PSTN side incoming calls.
3. If in communication with IP side, user can press HOLD to hold IP side, then press PSTN
to pick up PSTN side, after that can press HOLD again to retrieve IP side.
4. If
in communication with PSTN side, user must hang up PSTN side before pick up IP side
by pressing PSTN.
HOLD: To hold a call with H.450 function.
SPEED: Press SPEED and number (Phone book index) to do speed dial according to phone
book data (please refer to LCD configuration-Phone Address Book or Advanced
Configurations via Telnet-[pbook] command ).
FORWARD: Forward a incoming call to another IP device by H.450 forward function.(please
refer to LCD configuration-Indicate Forward Type)
MESSAGE and its indicated LED light: When missing the incoming calls, the message LED
will be flashing. User can know the information of miss call by pressing the message button.
TRANSFER:
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
9
1. Transfer a call by H.450 transfer function. Press TRANSFER button in communication and
press phone No. which user want to transferred to can transfer this call .
2. Change characters to be capital or lowercase: when press TRANSFER before press letters
can switch type of letters.
REDIAL: Redial the last outgoing call.
+ and - : Adjust the voice volume in communication.
SPEAKER: Speaking without picking up handset.
Note: All function keys mentioned above (except Number 1 –10, * and # ) are effective only in IP
Phone mode.
2.Back View
DC 9V: DC 9V power input outlet
LAN: RJ-45 connector, connected directly to the Hub through the straight CAT-5 cable.
PC: RJ-45 connector, connected directly to the PC through the straight CAT-5 cable
Line: RJ-11 connector, connected directly to the PSTN analog line.
Note: There are two LED indicated lights: LINK/ACT and 10/100 for LAN port and PC port. When
network status is in normal, LED of LINK/ACT will be flashing; when transmit rate is in 10
mbps/100mbps, LED of 10/100 will light off/on .
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
10
3.Specification of connector
1、Ethernet Port：
Ethernet port is for connecting LAN Phone to network, transmit rate supports 10/100 Base-T.
Ethernet connector（LAN）
2、RJ11connector：
RJ11 connector is for connecting LAN Phone with PSTN.
RJ11connector
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
11
Chapter 2 Operating Procedure – LCD Display Configuration
1.Initialize LAN Phone 101/201
1. When power on the LAN Phone 101/201, the LCD screen shows as below.
2. Wait around one minute until the LAN Phone 101/201 finishes boot program initialization.
3. User can see flashing greeting as below:
4. Then LAN Phone get into standby mode:
The main LCD screen would be shown as similar as above. The GK word means the LAN
Phone 101/201 is in GateKeeper Mode, and when LAN Phone is connected to SNTP server,
on LCD will show current time from SNTP server.
5. After pressing the PSTN button, the GK word will be replaced by PSTN. Then LAN Phone
is in PSTN Mode. Please notice that in PSTN mode user must plug PSTN line in RJ-11 port.
Press or to enter configuration mode then press OK Bottom to enter certain menu.
There are 6 selections for configuration.
1. System Configuration (mandatory, protected by password)
2. User Line Number (mandatory)
3. Ring Configuration
4. Indicate Forward Type
5. Message Box
6. Phone Address Book
IP-Phone
Board Start Booting
System Initializing…………..
IP-Phone
GK 10:10:10 AM
IP-Phone
PSTN 10:10:10 AM
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
12
Note: LCD Panel of LAN Phone 101/201 is operated manually by moving or on the
keypad. Press OK to enter separate configuration menu. Press C to go back to the main
menu.
2.LCD Configuration
User can set the following 10 configurations manually by operating the commands displayed on
LCD.
Note: Any configurations that have made for the LAN Phone 101/201, user has to do Reboot
in
the selection 1→5 “Reboot”.
1. System Configuration (mandatory, protected by password)
Please Enter Password:
User must key in password to enter this menu, selections under this command are all
important ones, which can only be configured by administrators.
Note: Password to enter System Configuration:
H.323 token password (please refer to item 9), default value is
x. (Please press
TRANSFER button to switch as lowercase characters first.)
1. Connect Configuration
There are ten sub-configurations included in Connect Configuration. It is necessary
for user to set it in order to run the LAN Phone 101/201 correctly.
In addition, user has to prepare one valid IP Address to meet your network
environment. (Global public IP Address or Virtual IP Address)
(1) IP address
In this configuration mode, user presses the prepared IP Address on the LAN
Phone keypad. Please input IP address as format: xxx.xxx.xxx.xxx.
(2) Subnet Mask:
User has to press the subnet mask IP Address on the LAN Phone keypad.
(3) Gateway
User has to press the default gateway IP which meets IP Address on the LAN
Phone keypad.
(4) Primary DNS
User can set IP address of Domain Name Server, then for GateKeeper and Phone
book can enter URL address or IP address. Please refer to 3.9 [pbook] and 3.12
[h323] command.
(5) Secondary DNS
User can set IP address of secondary DNS, once primary DNS cannot work
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
13
normally, LAN Phone can refer to secondary DNS.
(6) GateKeeper
User has to offer one available GateKeeper server IP Address and set this IP
Address on the LAN Phone keypad.
(7) Second GateKeeper
LAN Phone provide alternative GateKeeper feature, if LAN Phone can’t register
to Main GateKeeper for 10 times, it will try to register to the Second GateKeeper.
When main GateKeeper can’t work normally, LAN Phone can still keep working
with Second GateKeeper
(8) SNTP Configuration
LAN Phone 101/201 supports that user can assign one SNTP (Simple Network
Time Protocol) Server in your country by setting in LAN Phone. User has to
offer one available SNTP server IP Address and set this IP Address on the LAN
Phone keypad.
(A)SNTP Mode: User can set different time can set SNTP function too be
on/off/broadcast, which means LAN Phone will capture current time from
SNTP server or not, or broadcast to find a SNTP server and capture current
time.
(B) SNTP Server: User can specify a SNTP server for LAN Phone to capture
current time.
(C)Time Zone: User can set time zone according to the location LAN Phone is.
For example, in Taiwan the time zone should be set as 8,which means
GMT+8.(user can press “*” as “-“)
Note: If user didn’t set SNTP server, on LCD won’t display current time.
(9) Connection Mode
There are 2 types for LAN Phone 101/201 to connect to the other devices. They
are GK, P2P. The default mode is in GK mode. When user would like to connect
via P2P mode, the LAN Phone 101/201 must change as well. Move the “~”
symbol by press or on the keypad to select one mode.
(10) DHCP Mode (ON/Off)
User can set LAN Phone in DHCP mode, which means LAN Phone will get a
dynamic IP automatically.
(11) Token Password
(A) LCD menu password: User can enter LCD system configuration by key in
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
14
this password
(B)H.235 security: To set RRQ/ARQ authentication token password. If
LAN Phone wants to register to a GateKeeper, which implement H.235
security token feature, LAN Phone has to set a RRQ/ARQ authentication
token password, which is provided by GateKeeper manager. LAN Phone
can’t work normally with this GateKeeper unless Token Password is set.
(12) Management Center
Set management center IP address. IF user specifies management center IP
address, LAN Phone will connect and send information to management center,
let user can easily configure via management center interface.
Note: 1.management center is optional software to help user can easily
configure products, please contact your reseller to know more about it.
2.If user wants to disable Management Center function in LCD menu,
use can key in IP address 255.255.255.255.
(13) GRQ Option
To set auto discovery function OFF or ON. If this function is enabled and IP
address of GateKeeper is set as 255.255.255.255, LAN Phone will multicast to
search a GateKeeper on network with configured GateKeeper ID(please refer
to (12)Gatekeeper ID); if IP address of GateKeeper is set, before LAN Phone
register to the assigned GateKeeper, it will send out GRQ(GateKeeper Request)
message with configured GateKeeper name to GateKeeper first.
(14) GateKeeper ID
To set GateKeeper name for GateKeeper discovery. When LAN Phone send out
GateKeeper discovery message will search GateKeeper with this GateKeeper
name
2. User Line Name
User has to identify one ID name for the LAN Phone 101/201 to register to the
GateKeeper.
3. Firmware Update
(1) Download method
There are two methods to download new rom file, please move the “~” symbol by
press or on the keypad to select TFTP or FTP method, then press OK to
confirm it.
(2) Set File Server IP
User has to offer one TFTP/FTP server IP Address and set this IP Address on the
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
15
LAN Phone keypad. The IP Address is necessary for upgrading Lan Phone new
application rom file.
(3) Set FTP user account
User has to press user name and password for FTP server login .It is necessary for
upgrading Lan Phone new application rom file in FTP method.
(4) Indicate file name
User has to press the file name of new application rom file prepared for upgrading
(5) Start Download
Press OK to start download new application rom file. After download is finished,
LAN Phone will automatically reboot.
(6) Firmware Version
Show versions of all rom files and hardware.
Note: Download via LCD command can only upgrade new application rom file.
4. Hardware Test
LAN Phone 101/201 provides self-test for all functions buttons. Please follow the
direction from LCD panel to operate and verify it.
5. PPPoE Configuration
(1) PPPoE Mode
Choose ON or OFF to enable or disable PPPoE function.
(2) Username And Password
To set PPPoE connection user name and password.
(3) Retry When Disconnect
Choose ON or OFF to enable or disable this function. If user enable this function,
after PPPoE being disconnected, LAN Phone will automatically reboot to
re-connect, and after reboot, if LAN Phone still can’t get contact with server,
LAN Phone will keep trying to connect. On the other hand, if user disable this
function, LAN Phone won’t reboot and keep trying to connect.
6. Reboot
It is necessary and important for user to reboot it after any configurations has been
made to the LAN Phone 101/201.
2. User Line Number
User has to identify at least one number for the LAN Phone 101/201 to register to the
GateKeeper. User can set up to 10 different numbers.
(1) Line Number 1
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
16
(2) Line Number 2
(3) Line Number 3
(4) Line Number 4
(5) Line Number 5
(6) Line Number 6
(7) Line Number 7
(8) Line Number 8
(9) Line Number 9
(10) Line Number 10
Note: User can set six zero “000000”
on LCD to disable this number and the number
after this one. Ex. Line Number 1-5 are configured, if user set Line 3 as “000000”
,
Line number 3-5 will be disabled.
3. Ring Configuration
(1) Ring Style Selection
There are three tone styles for LAN Phone 101/201. Move the “~” symbol by press
or on the keypad to select the tone style preferred, then press OK to confirm it.
(2) Ring Volume Control
User can adjust ring volume by by press or on the keypad to decrease or
increase volume.
4. Indicate Forward Type
There are two selections to activate or deactivate forward function. After selection please
press OK
(1).Activate : choose under which situation to forward call to another endpoint. After
selection please press OK, then enter LINE NUMBER of another
endpoint prepared to forward to.
1. Busy
When LAN Phone 101/201 is in busy status, the incoming call will be directly
forwarded to the assigned phone number.
2. No response
When LAN Phone 101/201 is continuing ringing around 10 seconds, the incoming
call will be directly forwarded to the assigned phone number.
3. Unconditional
Choose Tone Style:
Low Middle High
LAN Phone 101/201 User Manual Guide Document Ver.: 2.0
LAN Phone Ver:lp2.100.
17
It is included the above two types. Whether the LAN Phone is in which status, it will
be automatically forwarded to the assigned phone number.
(2).Deactivate : choose under which situation to deactivate forward function. After
selection, please press
OK , then user can see LINE NUMBER of the
endpoint which is already configured to forward to, now press OK
again.
Note: The number that user prepares to forward to is E.164 number which is
registered on the GateKeeper.
5. Message Box
If there is an unanswered IP call, it will be kept in message box . MESSAGE LED will be
flashing until user press MESSAGE to check miss call and re-press MESSAGE to return
to main screen.
1. New Call：to see all incoming-call records in message box.
2. History：to see all records in message box.
6. Phone Address Book
1. Display
Display all name and telephone number recorded to the phone address book.
2. Add
Add and save name, telephone number and IP address of the phone address book.
3. Edit
Edit name, telephone number, and IP address of Phone book.
4. Delete
Delete the record in the phone address book.
Note: When key in IP address in Pbook table, please do not add 0 before IP
address (ex.10.1.1.1 please do not key in 010.001.001.001).
7. PPPoE Information
All items below can only be displayed when PPPoE connection is established, user can
check related information here.
1. PPPoE Status
Loading...