Sony SLV-SE600B, SLV-SE800B, SLV-SE700B, SLV-SX700B User Manual

3-868-352-E1 (1)

Video Cassette Recorder

Operating Instructions

PAL SECAM NTSC4.43

SLV-SE600B SLV-SE700B SLV-SX700B SLV-SE800B

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Mains lead must only be changed at a qualified service shop.

Precautions

Safety

• This unit operates on 220 – 240 V AC, 50 Hz. Check that the unit’s operating voltage is identical with your local power supply.

• If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.

• The unit is not disconnecte d from the mains as long as it is connected to the mains, even if the unit itself has been turned off.

• Unplug the unit from the wall outlet if you do not intend to use it for an extended period of time. To disconnect the cord, pull it out by the plug, never by the cord.

Installing

• Allow adequate air circulation to prevent internal heat buildup.

• Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots.

• Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.

• Do not install the unit in an inclined position. It is designed to be operated in a horizontal position only.

• Keep the unit and cassettes away from equipmen t with strong magnets, such as microwave o ven s o r large loudspeakers.

• Do not place heavy objects on the unit.

• If the unit is brought directly from a cold to a warm location, moisture may condense inside the VCR and cause damage to the video head and tape. When you first install the unit, or when you move it from a cold to a warm location, wait for about three hours before operating the unit.

Caution

Television programmes, films, video tapes and other materials may be copyr i gh te d. Un a uth or i z ed recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or programme owner.

Compatible colour systems

• This VCR is designed to record using the PAL (B/G) and SECAM colour systems an d play ba ck using the PAL (B/G), SECAM, and NTSC 4.43 colour systems. Recording of video sources based on other colour systems cannot be guaranteed.

• Tapes recorded with the MESECAM colour system can be played back on th is VCR using a TV or a colour monitor supporting the SECAM colour system.

HOWVIEW is a registered trademark of Gems tar

Development Corporation. The S is manufactured under license from Gemstar Development Corporation.

HOWVIEW system

WARNING

Table of contents

Getting Started

4 Step 1 : Unpacking 5 Step 2 : Setting up the remote commander

9 Step 3 : Connecting the VCR 13 Step 4 : Tuning your TV to the VCR 16 Step 5 : Setting up the VCR with the Auto Set Up function 18 Selecting a language 20 Presetting channels 25 Changing/disabling programme positions 31 Setting the clock 36 Setting the Canal Plus decoder

Basic Operations

41 Playing a tape 44 Recording TV programmes 48 Recording TV programmes using the

Dial Timer (SLV-SE800B only)

53 Recording TV programmes using the

ShowView system (not available on SLV-SE600B)

57 Setting the timer manually

Additional Operations

61 Playing/searching at various speeds 64 Setting the recording duration time 65 Synchronized Recording

(SLV-SE800B only)

68 Checking/changing/cancelling timer

settings

70 Recording stereo and bilingual

programmes

72 Searching using the Acces Smart

function

75 Searching using the index function 76 Adjusting the picture 78 Changing me nu options

Editing

81 Connecting to a VCR or stereo

system

83 Basic editing 84 Audio dubbing

(SLV-SE800B only)

Additional Information

86 Troubleshooting 90 Specifications 91 Index to parts and controls

Back Cover

Index

Getting Started

Table of contents

Getting Started

Step 1 : Unpacking

Check that you have received the following items with the VCR:

• Remote commander • Aerial cable

• R6 (size AA) batteries

Check your model name

The instructions in this manual are for the 4 models: SLV-SE600B, SE700B, SX700B, SE800B. Check your model number by looking at the rear panel of your VCR. SLV-SE800B is the model used for illustra tion purposes. Any difference in operation i s clearly indicated in the text, for example, “S LV-SE700B only.”

Unpacking

Step 2 : Setting up the remote commander

Inserting the batteries

Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment.

Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position.

Using the remote commander

You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. If the TV does not have

the symbol near the remote sensor, this remote commander will not operate the TV.

Getting Started

Remote sensor

[TV] / [MAGN]

123 456 789

To operate Set [TV] / [MAGN] to

the VCR [MAGN] and point at the remote sensor at the VCR a Sony TV [TV] and point at the remote sensor at the TV

continued

Setting up the remote commander

WIDE

CHOIX SON

FASTEXT buttons

?/1

AFFICH

123 456 789

t TV/MAGN

Programme number buttons

CHAINE +/–/ c/C

2 +/–

TV control buttons

To Press

Set the TV to standby mode ?/1 Select an input source: aerial in or line in t TV/MAGN Select the TV’s programme position Programme number buttons, -,

CHAINE +/–

Setting up the remote commander

To Press

Adjust the volume of the TV 2 +/– Switch to TV (Teletext off)* a (TV) Switch to Teletext* / (Teletext) Select the sound CHOIX SON Use FASTEXT* FASTEXT buttons Call up the on- s cr een display

Change the Teletext page* c/C Switch to/from wide mode of a Sony wide T V (For othe r

manufactures’ wide TVs, see “Controlling other TVs with the remote commander (not available on SLV-SE600B)” below.)

Notes

• With normal use, the batteries should last about three to six months.

• If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from batter y le akage.

• Do not use a new battery togethe r w it h an old one.

• Do not use different types of batteries together.

• Some buttons may not work with certain Sony TVs.

* not available on SLV-SE600B

AFFICH

WIDE

Controlling other TVs with the remote commander (not available on SLV-SE600B)

The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the following table, set the appro pri ate manufacturer’s code number.

Getting Started

Set [TV] / [MAGN] at the top of the remote commander to [TV].

Hold down ?/1, and enter your TV’s code number using the programme number

buttons. Then release ?/1. Now you can use the following TV contr ol buttons to control your TV:

?/1, t TV/MAG N, program me numbe r butto ns, - (ten’s digit), CHAINE +/–, 2 +/–, a (TV), / (Teletext), FASTEXT buttons, WIDE*, MENU*,

,*, and OK*.

* These buttons may not work with all TVs.

continued

Setting up the remote commander

M/m/</

Code numbers of controllable TVs

If more than one code number is listed, try entering th em on e at a time until you find the one that works with your TV.

To switch to wide mode, see the footnotes below this table for the applicable code numbers.

Manufactu r e r Code number

Sony

01*

, 02 Akai 68 Ferguson 52

Grundig

10*

, 11*

Hitachi 24 JVC 33 Loewe 45 Mivar 09, 70 NEC 66 Nokia

15, 16, 69*

Manufacturer Code number

Panasonic Philips

17* 06*

, 49

, 07*1, 08* Saba 12, 13 Samsung 22, 23 Sanyo 25 Sharp 29 Telefunken 36 Thomson

43*

Toshiba 38

*1Press WIDE to switch the wide picture mode on or off.

Press WIDE, then press 2 +/– to select the wide picture mode you want.

Press WIDE. The menu appears on the TV screen. Then, press M/m/</, to select the

wide picture you want and press OK.

Tip

• To see if you set your TV’s code number correc tl y, try turning your TV on and off with the ?/1 butto n.

Notes

• If you enter a new code number, the code numb er previously entered will be era sed.

• If the TV uses a different remote control syst em from the one programmed to work with the VCR, you cannot contro l your TV with the remote com ma nder.

• When you replace the batteries of the remote commander, the code number may change. Set the appropriate code number every time you replace the batteries.

Setting up the remote commander

Step 3 : Connecting the VCR

If your TV has a PERITEL connector, see page 10.

If your TV does not have a PERITEL connector

ANTENNE ENTREE

ANTENNE

Mains lead

to mains

: Signal flow

Disconnect the aerial cable from yo ur TV and connect it to ANTENNE ENTREE on the rear panel of the VCR.

Connect ANTENNE SORTIE of the VCR and the aerial input of your TV using the supplied aerial cab le.

SORTIE

Aerial cable (supplied)

ANTENNE ENTREE

AERIAL

ANTENNE IN

ENTREE

OUT

SORTIE

AERIAL

ANTENNE IN

ENTREE

OUT

SORTIE

Getting Started

Connect the mains lead to the mains.

Note

• When you connect the VCR and your TV only with an aerial cable, you have to tune your TV to the VCR (see page 13).

continued

Connecting the VCR

If your TV has a PERITEL connector

i LIGNE-1

Mains lead

to mains

: Signal flow

(TV)

Aerial cable (supplied)

PERITEL cable (not supplied)

ANTENNE ENTREE

ANTENNE SORTIE

ANTENNE ENTREE

PERITEL

Disconnect the aerial cable from your TV and connect it to ANTENNE ENTREE on the rear panel of the VCR.

Connect ANTTENNE SORTIE of the VCR and the aerial input of your TV using the supplied aerial cable.

AERIAL

ANTENNE

ENTREE

OUT

SORTIE

AERIAL

ANTENNE

ENTREE

OUT

SORTIE

Connect LIGNE-1 (TV) on the VCR and the PERITEL connector on the TV with the optional PERITEL cable.

This connection improves picture and sound quality. Whenever you want to watch the VCR picture, press t TV/ MAGN to display the MAGN indicator in the display window.

Connect the mains lead to the mains.

Note

• If the TV is con nected to the L IGNE-1 (TV) connector, settin g the RF channe l to OFF is

recommended. In the OFF posi ti on, only the signal from the aerial is out put through the ANTENNE SORTIE connector (see page 15).

Connecting the VCR

About the SMARTLINK features (not available on SLV-SE600B)

If the connected TV complies with SMARTLINK, MEGALOGIC*1, EASYLINK*2, Q-Link*3, EURO VIEW LINK*4, or T-V LINK*5, this VCR automatically runs the SMARTLINK function after you complete the steps on the previous page (the SMARTLINK indicator appear s in the VCR’s display window when you turn on the TV). You can enjoy the following SMARTLINK features.

• Preset Download You can download your TV tuner preset data to this VCR and tune the VCR according to that data in Auto Set Up. This greatly simplifies the Auto Set Up procedure. Be careful not to disconnect the cables or e xit the Auto Set Up function during the procedure. See “Setting up the VCR with the Auto Set Up function” on page 16.

• TV Direct Rec You can easily record what you are watching on the TV. For details, see “Recording what you are watching on the TV (TV Direct Rec) (not available on SLV-SE600B)” on page 47.

• One Touch Play With One Touch Play, you can start playback automatically without turning on the TV. For details, see “Starting playback automatically with one button (One Touch Play) (not available on SLV-SE600B)” on page 43.

• One Touch Menu You can turn on the VCR and TV, set the TV to the video channel, and d isplay the VCR’s on-screen display automati cally by pressing MENU on the remote commander.

• One Touch Timer You can turn on the VCR and TV, set the TV to the video channel, and d isplay the timer recording menu (the METHODE DE PROGRAMMATION menu, the

MINUTERIE menu, or the SHOWVIEW menu) automatically by pressing MINUTERIE on the remote commander. You can set which timer recording menu is displayed using OPTIONS PROGRAMM. in the OPTIONS-2 menu (see page 79).

• Automatic Power Off You can have the VCR tu rn off automatically, if th e VCR is no t u sed af ter you turn off the TV.

SMARTLINK

Getting Started

*1“MEGALOGIC” is a re g i stered trademar k of Gr u ndig Corporatio n.

“EASYLINK” is a trademark of Philips Corporation.

“Q-Link” is a trademark of Panaso nic Corporation.

“EURO VIEW LINK” is a trademark of Toshiba Co rporation.

“T-V LINK” is a trademark of JVC Corporation.

Note

• Not all TVs respond to the functions above.

continued

Connecting the VCR

Additional connections

To a stereo system (not available on SLV-SE600B)

You can impro ve sound quality by connecting a stereo system to the SORTIE AUDIO R/L jacks as shown on the right.

T o a satellite or digital tuner with Line Through

Using the Line Throug h function, you can w at ch programmes from a satellite or digital tuner connected to thi s VCR on the TV even when the VCR is turned off. When you turn on the satellite or digital tuner, this VCR automatically sends the signal from the satellite or digital tuner to the TV without turning itself on.

SORTIE AUDIO D/G

Audio cable (not supplied)

: Signal flow

DECODEUR/ t ENTREE LIGNE-3* DECODEUR/ t ENTREE LIGNE-2*

: Signal flow

ENTREE LIGNE

SORTIE LIGNE

PERITEL cable (not supplied)

Connecting the VCR

Connect the satellite or digital tuner to the DECODEUR/ENTREE LIGNE-3*1

(or DECODEUR/ENTREE LIGNE-2*2) connector as shown above. Set DECODEUR/ENTREE LIGNE-3*1 (or DECODEUR/ENTREE LIGNE-2*2)

to LIGNE3*1 (or LIGNE2*2) in the OPTIONS-2 menu. Set VEILLE ECO to NON in the OPTIONS-2 menu.

Turn off the VCR.

To watch a programme, turn on the satellite or digital tuner and the TV.

Note

• You cannot watch programmes on the TV while recording unless you are recording a satellite

or digital programme.

SLV-SE800B only

SLV-SE600B, SE700B, and SX700B onl y

Step 4 : Tuning your TV to the VCR

1 2

If your TV has a PERITEL connector, see page 15.

If your TV does not have a PERITEL connector

Follow the steps below so that your TV will properly receive the video signals from your VCR.

REGL CANAL

CHAINE +/–

MARCHE/VEILLE

REGLAGE

AUTO

REGL CANAL

?/1 MARCHE/VEILLE

Press ?/1 MARCHE/VEILLE to turn on the VCR.

Press REGL CANAL on the VCR lightly. The factory-preset RF channel appears in the display window. The VCR signal is output through this channel to the TV.

Getting Started

3 4

REGLAGE

AUTO

REGL CANAL

Turn on your TV and select a programme position for the VCR picture. This programme position will now be referred t o as the video channel.

Press REGL CANAL. The TV system appears in the display window.

continued

Tuning your TV to the VCR

CHAINE

ALIGNEMENT

Press CHAINE +/– (repeatedly) to select the appropriate TV system for your area.

Select “L” for the L TV system (SECAM), or “G” for the B/G TV system (PAL).

Tune the TV to the sa me cha n nel shown in the VCR display window so that the picture on the right appears clearly on the TV screen.

Refer to your TV manual for TV tuning instructions.

If you select the wrong TV system in step 5, the picture on the right may not appear. Select the appropriate TV system and tune the TV again.

If the picture does not appear clearly, see “To obtain a clear picture from the VCR” below.

REGLAGE

AUTO

REGL CANAL

To check to see if the TV tuning is correct

Set the TV to the video channel and press CHAINE +/– on the VCR. If the TV screen changes to a different programme each time you press CHAINE +/–, the TV tuning is correct.

To obtain a clear picture from the VCR

If the screen does not appear clearly in step 6 above, go to step 7 to finish this procedure once. Then start again from step 2. After pressing REGL CANAL in step 2, press CHAINE +/– while the RF channel is displayed, so that another RF channel appears. Then tune the TV to the new RF channel so th at a clear picture appears.

Press REGL CANAL. You have now tuned your TV to the VCR. Whenever you want to play a

tape, set the TV to the video channel.

MAGNETOSCOPE SONY

Tuning your TV to the VCR

If your TV has a PERITEL connector

1 2

MARCHE/VEILLE

REGLAGE

AUTO

REGL CANAL

CHAINE

ALIGNEMENT

REGLAGE

AUTO

?/1 MARCHE/VEILLE

REGL CANAL

CHAINE +/–

Press ?/1 MARCHE/VEILLE to turn on the VCR.

Press REGL CANAL on the VCR lightly. The factory-preset RF channel appears in the display window. The VCR signal is output through this channel to the TV.

Press CHAINE +/– to set the RF channel to OFF, and press REGL CAN AL again.

RF channel set up is complete.

Getting Started

REGL CANAL

Tuning your TV to the VCR

Step 5 : Setting up the VCR with the Auto Set Up function

Before using the VCR for the first time, set up the VCR using the Auto Set Up function. With this function, you can set the TV channels, guide channels for the ShowView system*, and VCR clock* automatica lly.

REGL AGE AUTO

REGLAGE

AUTO

REGL CANAL

Hold down REGLAGE AUTO on the VCR for more than three seconds. The VCR automatically turns on, starts searchi ng for al l of th e receivable

channels, and presets them in th e appropriate order for your local area (according to the TV system you selected in “Tuning your TV to the VCR”).

If you want to change the order of the channels or disabl e unwanted programme positions, see “Changing/disablin g programme positions” on page 25.

If you use the SMARTLINK connection (not available on SLV-SE600B), the Preset Download function starts and the SMARTLINK indicator flashes in the display window during download.

After the search or download is complete, the current time appears in the display window for any stations that transmit a time signal (not available on SL V-SE600B). If the time does not appear, set the clock manually (see page

31).

Setting up the VCR with the Auto Set Up function

To cancel the Auto Set Up function

Press REGLAGE AUTO.

Tip

• If you want to change the language for the on-screen display from th e one preset in the Auto Set Up function, see page 18.

Notes

• Do not cancel the Auto Set Up function. If you do, repeat the steps above.

• The Auto Set Up function may require a long time to complete (approximately 15 to 18

minutes).

• Whenever you operate the Auto Set Up function, some of the settin gs (ShowView*, timer, etc.) will be reset. If this happens, you have to set them again .

* not available on SLV-SE600B

Getting Started

Setting up the VCR with the Auto Set Up function

Selecting a langu age

If you prefer an on-screen language other than French, use the on-scree n display to select another lan gu a ge .

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the video channel.

LECTURE

Press MENU, then press M/m to highlight REGLAGES and press OK.

REGLAGES

REGLAGE DES CHAINES HORLOGE LANGUE

RETOUR

SELECTIONNER

M/m

::OKREGLER

SORTIE

MENU:

Selecting a language

LECTURE

Press M/m to highlight LANGUE, then press OK.

LANGUE

SELECTIONNER

ENGLISH FRANÇAIS

: : OKREGLER

SORTIE

MENU:

Press M/m to highlight the desired language, then press OK.

LECTURE

Getting Started

Tip

• If you want to return to the previous menu, highlight RETOUR and press OK .

Note

• The menu disappears automat ical l y if you don’t proceed for more than a few minutes.

Press MENU to exit the menu.

Selecting a language

Presetting channels

If some channels could not be preset using the Auto Set Up function, you can preset them manually.

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the video channel.

123 456 789

Programme number buttons

CHAINE +/–

Presetting channels

LECTURE

Press MENU, then press M/m to highlight REGLAGES and press OK.

REGLAGES

REGLAGE DES CHAINES HORLOGE LANGUE

RETOUR

SELECTIONNER

::OKREGLER

M/m/</,

MENU:

SORTIE

LECTURE

Press M/m to highlight REGLAGE DES CHAINES, then press OK.

REGLAGE DES CHAINES

NORME L NORMAL / CABLE REGLAGE CANAL

TV-PAYANTE / CANAL+

AFT ACCORD FIN

RETOUR

SELECTIONNER

::OKREGLER

NORMAL

NON OUI

SORTIE

PROG.

AAB12

Getting Started

MENU:

LECTURE

Press M/m to highlight NORME, then press OK.

Press M/m to highlight L or B/G, then press OK.

• To receive broadcasts in France, highlight L.

• To receive broadcasts using the PAL system (for example, in Germany or Switzerland), highlight B/G.

Press M/m to highlight NORMAL/ CABLE, then press OK.

REGLAGE DES CHAINES

NORME L NORMAL / CABLE REGLAGE CANAL

TV-PAYANTE / CANAL+

AFT ACCORD FIN

RETOUR

SELECTIONNER

NORME L NORMAL / CABLE REGLAGE CANAL

TV-PAYANTE / CANAL+

AFT ACCORD FIN

RETOUR

SELECTIONNER

NORME NORMAL / CABLE REGLAGE CANAL

TV-PAYANTE / CANAL+

AFT ACCORD FIN

RETOUR

SELECTIONNER

::OKCONFIRMER

REGLAGE DES CHAINES

::OKREGLER

REGLAGE DES CHAINES

::OKCONFIRMER

B / G

NON OUI

SORTIE

NORMAL

NON OUI

SORTIE

NORMAL CABLE

OUI

SORTIE

PROG.

AAB12

PROG.

MENU:

LECTURE

Press M/m to highlight NORMAL, then press OK.

To preset CATV (Cable Television) channels, select CABLE.

REGLAGE DES CHAINES

NORME L NORMAL / CABLE REGLAGE CANAL

TV-PAYANTE / CANAL+

AFT ACCORD FIN

RETOUR

SELECTIONNER

::OKREGLER

continued

Presetting channels

NORMAL

NON OUI

SORTIE

PROG.

AAB12

MENU:

• CHAINE

Press CHAINE +/– to select the programme position.

Selected programme position

REGLAGE DES CHAINES

NORME L NORMAL / CABLE REGLAGE CANAL

TV-PAYANTE / CANAL+

AFT ACCORD FIN

RETOUR

SELECTIONNER

::OKREGLER

NORMAL

NON OUI

SORTIE

PROG.

AAB12

MENU:

LECTURE

123 456 789

Press M/m to highlight REGLAGE CANAL, then press OK.

REGLAGE DES CHAINES

NORME L NORMAL / CABLE REGLAGE CANAL

TV-PAYANTE / CANAL+

AFT ACCORD FIN

RETOUR

SELECTIONNER

: :

OKCONFIRMER

OUI

SORTIE

PROG.

AAB12

MENU:

Press M/m repeatedly until the channel you want is displayed. The channels appear in the following

order:

Channel coverage

VHF F2 - F10 E2 - E12

UHF F21 - F69 E21 - E69 CATV (TV

distribution) HYPER S21 - S41 S21 - S41

System L System B/G

Italian channels A - H

B - Q S01 - S05,

S1 - S20

REGLAGE DES CHAINES

NORME L NORMAL / CABLE REGLAGE CANAL

TV-PAYANTE / CANAL+

AFT ACCORD FIN

RETOUR

SELECTIONNER

: :

OKCONFIRMER

OUI

SORTIE

PROG.

MENU:

If you know the number of the channel you want, press the programme number buttons. For example, for channel 5, first press “0” and then press “5.”

10 11

Presetting channels

To preset another programme position, repeat steps 7 through 9.

Press MENU to exit the menu.

If the picture is not clear

Normally, the Auto Fine Tuning (AFT) function automatically tunes in channels clearly. However, if the picture is not clear, you may also use the manual tuning function.

Press CHAINE +/– or the programme number buttons to select the programme

position for which you cannot obtain a clear picture. Press MENU, then select REGLAGES and press OK.

Select REGLAGE DES CHAINES, then press OK.

Select ACCORD FIN, then press OK.

The fine tuning meter appears.

REGLAGE DES CHAINES

NORME L NORMAL / CABLE REGLAGE CANAL

TV-PAYANTE / CANAL+

AFT ACCORD FIN

RETOUR

REGLER :

Press </, to get a clearer picture, then press MENU to exit the menu.

Note that the AFT (Auto Fine Tuning) setting switches to NON.

NORMAL

NON

SORTIE

PROG.

Selected programme position

MENU:

Getting Started

continued

Presetting channels

Tuning the French CATV channels

This VCR can scan the CATV channels B to Q and the HYPER frequency channels S21 to S41. On the REGLAGE DES CHAINES menu, the channels are indicated by S01 to S44 REGLAGE CANAL numbers respectively. For example, channel B is indicated by REGLAGE CANAL number S01 and channel Q by REGLAGE CANAL number S23. (See the table below.)

If the CATV channel you want to preset is indicated by its frequency (for example,

152.75 MHz), refer to the table below to find the corresponding channel number. Channel number S05 is for this example.

Channel system for the French CATV network

Corresponding channel

B S01 116.75–124.75 C S02 124.75–132.75 D S03 132.75–140.75 D S04 140.75–148.75 E S05 148.75–156.75 F S06 156.75–164.75 F S07 164.75–172.75 G S08 172.75–180.75 H S09 180.75–188.75 H S10 188.75–196.75

I S11 196.75–204.75 J S12 204.75–212.75

J S13 212.75–220.75 K S14 220.75–228.75 L S15 228.75–236.75 L S16 236.75–244.75

M S17 244.75–252.75

N S18 252.75–260.75 N S19 260.75–268.75 O S20 268.75–276.75 P S21 276.75–284.75 P S22 284.75–292.75 Q S23 292.75–300.75

REGLAGE CANAL number

Receivable frequency range (MHz)

Corresponding channel

S21 S24 299.25–307.25 S22 S25 307.25–315.25 S23 S26 315.25–323.25 S24 S27 323.25–331.25 S25 S28 331.25–339.25 S26 S29 339.25–347.25 S27 S30 347.25–355.25 S28 S31 355.25–363.25 S29 S32 363.25–371.25 S30 S33 371.25–379.25 S31 S34 379.25–387.25 S32 S35 387.25–395.25 S33 S36 395.25–403.25 S34 S37 403.25–411.25 S35 S38 411.25–419.25 S36 S39 419.25–427.25 S37 S40 427.25–435.25 S38 S41 435.25–443.25 S39 S42 443.25–451.25 S40 S43 451.25–459.25 S41 S44 459.25–467.25

REGLAGE CANAL number

Receivable frequency range (MHz)

Presetting channels

Tip

• If you want to return to the previous menu, highlight RETOUR and press OK.

Notes

• The menu disappears automatically if you don’t proceed for more than a few minutes.

• When adjusting ACCORD FIN, the menu may become difficult to read due to interference

from the picture being received.

Changing/disabling programme positions

After setting the channels, you can change the programme positions as you like. If any programme positions are unused or contain unwanted channels, you can disable them.

You can also change the station names (not available on SLV-SE600B). If the station names are not displayed, you can enter them manually.

Changing programme positions

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the video channel.

LECTURE

Press MENU, then press M/m to highlight LISTES and press OK.

LISTES

LISTE DES CHAINES LISTE DES PROGRAMMATIONS

RETOUR

SELECTIONNER REGLER

::OK

M/m/,

SORTIE

Getting Started

MENU:

LECTURE

Press M/m to highlight LISTE DES CHAINES, then press OK.

LISTE DES CHAINES

PROG

NOM

AAB

CDE

4 5

FGH

SELECTIONNER : DEPLACER PROG.:: SUPPR. PROG.

ANNUL / 0

MENUSORTIE :

continued

Changing/disabling programme positions

LECTURE

Press M/m to highlight the row which you want to change the programme positio n, then press ,.

To display other pag e s f or programme positions 6 to 60, press M/m repeatedly.

LISTE DES CHAINES

PROG

4 5

SELECTIONNER : REGLER NOM DU PROG.:: CONFIRMER

NOM AAB CDE

FGH

SORTIE

MENU:

6 7

LECTURE

Press M/m until the selected channel row moves to the desired programme position.

The selected channel is inserted at the new programme position and the intermediate channels are displaced to fill the gap.

LISTE DES CHAINES

PROG

4 5

SELECTIONNER : REGLER NOM DU PROG.:: CONFIRMER

NOM CDE

AAB FGH

SORTIE

Press OK to confirm the setting.

LECTURE

T o cha nge th e progr amme p osit ion of anothe r statio n, rep eat s teps 3 throug h

Tip

• If you want to return to the previous menu, highlight RETOUR and press OK.

Note

• The menu disappears automatically if you don’t proceed for more than a few minutes.

Press MENU to exit the menu.

MENU:

Changing/disabling programme positions

Disabling unwanted programme positions

After presetting channels, you can disable unused programme positions. The disabled positions will be skipped later when you press the CHAINE +/– buttons.

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the video channel.

Getting Started

ANNUL/0

123 456 789

M/m

LECTURE

Press MENU, then press M/m to highlight LISTES, and press OK.

Press M/m to highlight LISTE DES CHAINES, then press OK.

Changing/disabling programme positions

LISTES

LISTE DES CHAINES LISTE DES PROGRAMMATIONS

RETOUR

SELECTIONNER REGLER

SELECTIONNER : DEPLACER PROG.:: SUPPR. PROG.

::OK

LISTE DES CHAINES

PROG

4 5

ANNUL / 0

continued

NOM AAB CDE

FGH

SORTIE

MENU:

MENUSORTIE :

LECTURE

Press M/m to highlight the row which you want to disable.

LISTE DES CHAINES

PROG

1 2 3 4 5

SELECTIONNER : DEPLACER PROG.:: SUPPR. PROG.

2 3 6

ANNUL / 0

NOM AAB CDE

FGH

SORTIE

MENU:

5 6

ANNUL/0

Press ANNUL/0. The selected row will be cleared as shown

on the right.

LISTE DES CHAINES

PROG

1 2 3 4 5

SELECTIONNER : DEPLACER PROG.:: SUPPR. PROG.

2 3

ANNUL / 0

NOM AAB CDE

FGH

SORTIE

Repeat steps 3 and 4 fo r any ot her programme pos itions you want to disable.

Tip

• If you want to return to the previous menu, highlight RETOUR and press OK.

Notes

• The menu disappears automatically if you don’t proceed for more than a few minutes.

• Be sure to select the programme position you want to disable correctly. If you disable a

Press MENU to exit the menu.

programme position by mistake, you ne e d to re set tha t cha nne l m an ually.

MENU:

Changing/disabling programme positions

Changing the station names (not available on SLV-SE600B)

You can change or enter the station names (up to 5 characters). The VCR must receive channel information (for instance, SMARTLI NK information) for station names to appear automatically.

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the video channel.

Getting Started

M/m/</,

LECTURE

Press MENU, then press M/m to highlight LISTES and press OK.

Press M/m to highlight LISTE DES CHAINES, then press OK.

Press M/m to highlight the row which you want to change or enter the station name, then press ,.

To display other pages for programme positions 6 to 60, press M/m repeatedly.

LISTES

LISTE DES CHAINES LISTE DES PROGRAMMATIONS

RETOUR

SELECTIONNER REGLER

SELECTIONNER : DEPLACER PROG.:: SUPPR. PROG.

SELECTIONNER : REGLER NOM DU PROG.:: CONFIRMER

::OK

LISTE DES CHAINES

PROG

4 5

ANNUL / 0

LISTE DES CHAINES

PROG

4 5

NOM AAB CDE

FGH

NOM AAB CDE

FGH

SORTIE

MENU:

MENUSORTIE :

MENU:

continued

Changing/disabling programme positions

LECTURE

Press ,.

LISTE DES CHAINES

PROG

4 5

SELECT. UN CARACT. : SUIVANT CONFIRMER OK

: :

NOM AAB CDE

FGH

SORTIE

MENU:

LECTURE

Enter the station name. 1 Press M/m to select a character.

Each time you press M, the character changes as shown below.

A t B t … t Z t a t b t … t z t 0 t 1 t … t 9 t (symbols) t (blank space) t A

LISTE DES CHAINES

PROG

4 5

SELECT. UN CARACT. : SUIVANT CONFIRMER OK

2 Press , t o set the next character.

The next space is highlighted. To correct a character, press </, until the character you want to correct is highlighted, then reset it.

You can set up to 5 characters for the station name.

Press OK to confirm the new name.

LECTURE

Tip

• If you want to return to the previous menu, highlight RETOUR and press OK.

Press MENU to exit the menu.

NOM CAB

CDE

3 6

FGH

: :

SORTIE

MENU:

Notes

• The menu disappears automatically if you don’t proceed for more than a few minutes.

• If you enter a symbol in step 5, it will appear as a blank space in the display window.

Changing/disabling programme positions

+ 70 hidden pages