Sony IPELA SNC-RZ25P User Manual

3-857-261-11 (1)

Network Camera

User’s Guide

Software Version 1.0

SNC-RZ25N/RZ25P

© 2004 Sony Corporation

Owner's Record

The model and serial numbers are located on the bottom. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product.

Model No. ____________________

Serial No. ____________________

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

WARNING

This installation should be made by a qualified service person and should conform to all local codes.

WARNING

A readily accessible disconnect device shall be incorporated in the building installtion wiring.

WARNING (for Installers only)

Instructions for installing the equipment on the ceiling: After the installtion, ensure the connection is capable of supporting four times the weight of the rquipment downwards.

CAUTION

The rating label is located on the bottom.

CAUTION for LAN port

For safety reason, do not connect the LAN port to any network devices that might have excessive voltage.

Power Supply

Caution for U.S.A. and Canada

The SNC-RZ25N operates on 24V AC or 12V DC. The SNC-RZ25N automatically detects the power. Use a Class 2 power supply which is UL Listed (in the U. S. A.) or CSA-certified (in Canada).

Caution for other countries

The SNC-RZ25P operates on 24V AC or 12V DC. The SNC-RZ25P automatically detects the power. Use a power supply rated 24 V AC or 12 V DC witch meets the requirements for SELV (Safety Extra Low Voltage) and complies with Limited Power Source according to IEC 60950.

For customers in the U.S.A. (SNC-RZ25N only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wll not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

The shielded interface cable recommended in this manual must be used with this equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

If you have any questions about this product, you may call:

Sony’s Business Information Center (BIC) at 1- 800-686-SONY(7669)

or Write to: Sony Customer Information Services Center

6900-29, Daniels Parkway, PMB 330 Fort Myers, Florida 33912

Declaration of Conformity

Trade Name:	SONY
Model No:	SNC-RZ25N
Responsible Party:	Sony Electronics Inc.
Address:	16450 W. Bernardo
	Dr, san Diego, CA
	92127 USA
Telephone No:	858-942-2230

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

2

NOTICE TO USERS

© 2004 Sony Corporation. All rights reserved. This manual or the software described herein, in whole or in part, may not be reproduced, translated or reduced to any machine readable form without prior written approval from Sony Corporation.

SONY CORPORATION PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL, THE SOFTWARE OR OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO THIS MANUAL, THE SOFTWARE OR SUCH OTHER INFORMATION. IN NO EVENT SHALL SONY CORPORATION BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, WHETHER BASED ON TORT, CONTRACT, OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL, THE SOFTWARE OR OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF.

Sony Corporation reserves the right to make any modification to this manual or the information contained herein at any time without notice.

The software described herein may also be governed by the terms of a separate user license agreement.

Microsoft, Windows, Internet Explorer and MS-DOS are registered trademarks of Microsoft Corporation in the United States and/or other countries.

Java is a trademark of Sun Microsystems, Inc. in the United States and other countries.

Intel and Pentium are registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.

All other company and product names are trademarks or registered trademarks of the respective companies or their respective makers.

3

Table of Contents
Overview
Features ..................................................................	6
How to Use This User’s Guide ..............................	7
Precautions .............................................................	7
Operating Precautions ........................................	7
System Requirements ............................................	8
Preparation
Assigning the IP Address to the Camera ............	9
Assigning the IP Address Using the Setup
Program ............................................................	9
Accessing the Camera Using the Web Browser 11
Basic Configuring by the Administrator ...........	13
Operating the Camera
Administrator and User .....................................	14
Logging in to Homepage — Welcome Page ......	15
Logging in as a User ........................................	15
Displaying the setting window for the
administrator directly .....................................	16
About Viewers ..................................................	16
Configuration of Main Viewer ...........................	17
Main menu .......................................................	17
Camera Control Section ...................................	18
Monitor Image ..................................................	19
Controlling the Monitor Image ..........................	20
Monitoring the camera image ..........................	20
Zooming in the monitor image .........................	20
Capturing a Monitor Image ...............................	21
Capturing a monitor image ..............................	21
Saving the captured image ...............................	21
Operating the camera .........................................	22
Operating by using the Control panel ..............	22
Controlling via the control panel .....................	22
Control the camera in the monitor window ......	22
Zoom an image by the camera zoom bar .........	23
Moving the camera to the preset position ........	23
Controlling the camera on a panorama image . 24
Facing the camera toward the specified point ..	24
Sending an Image File .........................................	25
Sending a Monitor Image via E-mail ...............	25
Sending a Monitor Image to an FTP Server .....	25
Recording a Still Image in the Memory of the
Camera .................................................................	25
Controlling Alarm output 1, 2 ............................	26
Controlling Day/Night Function ........................	26
Switching TCP/UDP Transmission Mode .........	27

Administrating the Camera
Basic Operations of Administrator Menu .........	28
How to set Administrator menu ........................	28
Configuration of Advanced mode Menu ..........	29
Configuring the System — System setting
menu ......................................................................	31
System Tab ........................................................	31
Date & time Tab ................................................	32
Initialize Tab .....................................................	33
System log Tab .................................................	33
Access log tab ...................................................	34
Setting the Camera Image and Audio
— Camera setting Menu .....................................	34
Common Tab ....................................................	34
Picture Tab ........................................................	36
Day/Night Tab ..................................................	37
MPEG4 Tab ......................................................	38
JPEG Tab ..........................................................	38
Reset Tab ..........................................................	39
Configuring the Network — Network setting
Menu .....................................................................	40
Network Tab .....................................................	40
Wireless Tab — Setting of Wireless
Connection ........................................................	41
Wireless authentication Tab - Setting the Wireless
Authentication ................................................	42
PPPoE Tab - Setting of PPPoE Connection ......	42
Dynamic IP address notification Tab — Notifying
the IP Address .................................................	43
Setting the User — User setting Menu ...............	44
Setting the Security — Security setting Menu ..	45
Sending an Image via mail — e-Mail (SMTP)
setting Menu .........................................................	46
Common Tab — Setting the SMTP Function ...	46
Alarm sending Tab — Setting the mail sending
mode when detecting the alarm ......................	47
Periodical sending Tab — Setting the periodical
mail sending mode ..........................................	48
Sending Images to FTP Server
— FTP client setting Menu .................................	49
Common Tab — Setting the FTP Client
Function ..........................................................	49
Alarm sending Tab — Setting the FTP client
action when detecting the alarm .....................	50
Periodical sending Tab — Setting the Periodical
FTP Client Activity ........................................	51
Recording Images in Memory
— Image memory setting Menu .........................	52
Common Tab — Setting the Image memory
Function ..........................................................	52
Alarm recording Tab — Setting the Image
Memory Function when Detecting the Alarm 53
Periodical recording Tab — Setting the Periodical
recording mode ...............................................	54
Directory Structure of Image Memory .............	55

4 Table of Contents

Downloading Images from the Camera — FTP		Index ......................................................................	80
server setting Menu .............................................	55
Setting the Alarm Output
— Alarm output setting Menu ...........................	56
Alarm output 1, 2 Tab .........................................	56
Setting the Operations from the Viewer Page —
Trigger setting Menu ...........................................	57
Setting the Schedule
— Schedule setting Menu ...................................	59
Setting the Alarm Buffer — Alarm buffer setting
Menu .....................................................................	60
Setting the Motion Detection Function — Motion
detection setting Menu ........................................	61
Setting the Motion Detection Area, Sensitivity and
Threshold level ...............................................	62
Saving the Camera Position and Action — Preset
position setting Menu ..........................................	63
Preset position tab — Saving PanTilt and Zoom
position ...........................................................	63
Tour Setting Tab — Setting a Tour ...................	64
Transmitting with External Equipment Using the
External Serial Terminal
— Serial setting Menu .......................................	65
Others
Using the Supplied Setup Program ....................	66
Starting the Setup Program ..............................	66
Bandwidth Control Tab ....................................	66
Date time Tab ...................................................	67
PPPoE Tab ........................................................	67
Rebooting the Camera ......................................	68
Using the SNC audio upload tool — Transmitting
Audio to Camera ..................................................	68
Installing the SNC audio upload tool ...............	68
Connecting the Camera to the Computer .........	69
Using the SNC audio upload tool .....................	69
Using the SNC video player — Playing Video/
Audio File Recorded on Camera ........................	70
Downloading the SNC video player .................	70
Using the SNC video player .............................	70
Using the SNC panorama creator – Creating a
Panorama Image ..................................................	71
Installing the SNC panorama creator ...............	71
Using the SNC panorama creator .....................	71
Using the Custom Homepage Installer ..............	73
Uploading the Custom Homepage Installer to the
Camera ...........................................................	73
Assigning the IP Address to the Camera Using
ARP Commands ..................................................	75
Using the SNMP ...................................................	76
1. Inquiry Commands ......................................	76
2. Setting Commands ......................................	76
Specifications ........................................................	78

Table of Contents	5

Overview

Overview

Features

High-quality monitoring via the network

You can monitor a high-quality live image from the camera using the Web browser on the computer connected to the 10BASE-T or 100BASE-TX network. The maximum frame rate is 30 FPS for the SNC-RZ25N and 25 FPS for the SNC-RZ25P.

Up to 20 users can view the image from one camera at the same time (in JPEG mode).

Available Web browsers

Microsoft Internet Explorer Ver. 5.5 or 6.0 Available OS: Windows 2000/ XP

Remote-controllable high-speed pan/tilt mechanism and high magnification autofocus zoom lens

The camera is provided with a high-speed (100° rotation / second), wide-angle (–170° to +170°) pan mechanism, a high-speed (90° rotation / second), wide-angle (–90° to +30°) tilt mechanism, and a high-magnification zoom lens with optical zoom of 18 magnifications, electrical zoom of 12 magnifications, giving 216 magnifications in total.

Wireless LAN

Inserting the Wireless Card SNCA-CFW1 especially designed to use with this camera into the CF card slot enables transmission of images from the camera via wireless LAN.

Image transmission using an E-mail or FTP server

You can send a still image from the camera as an attachment of an E-mail or to an FTP server, at the moment when a trigger by the external sensor input, built-in activity detection function or manual trigger button occurs. You can also send still images sequentially for a determined period before and after the trigger to an FTP server, or send them periodically.

Preset positions and Tour programs

You can save up to 16 preset positions (pan, tilt and zoom positions) of the camera, and up to 5 tour programs composed from the preset positions. You can activate the preset positions by synchronizing with the external sensor input or built-in activity detection function.

Alarm output

The camera is equipped with two sets of alarm outputs. You can use them to control peripheral devices by synchronizing with the external sensor inputs, built-in activity detection function, manual trigger button, Day/ Night function or timer.

Direct panning/tilting

Clicking on the desired point in the displayed window allows you to pan and tilt the camera in the direction of that point

•Microsoft, Windows, Internet Explorer and MS-DOS are registered trademarks of Microsoft Corporation in the United States and/or other countries.

•CCD: Charge-Coupled Device

6 Features

How to Use This User’s Guide

This User’s Guide explains how to operate the SNCRZ25N and SNC-RZ25P Network Camera from a computer.

The User’s Guide is written to be read on the computer display.

As this section gives tips on using the User’s Guide, read it before you operate the camera.

Jumping to the related page

When you read the User’s Guide on the computer display, click on the sentence to jump to the related page.

Software display examples

Note that the displays shown in the User’s Guide are explanatory examples. Some displays may be different from the ones which appear as you operate the application software.

Printing the User’s Guide

Depending on your system, certain displays or illustrations in the User’s Guide, when printed out, may differ from those as portrayed on your screen.

Installation Manual (printed matter)

The supplied Installation Manual describes the names and functions of parts and controls of the Network Camera, connecting examples and how to set up the camera. Be sure to read the Installation Manual before operating.

Precautions

This Sony product has been designed with safety in mind. However, if not used properly electrical products can cause fires which may lead to serious body injury. To avoid such accidents, be sure to heed the following.

Heed the safety precautions

Be sure to follow the general safety precautions and the “Operating Precautions.”

In case of a breakdown

In case of system breakdown, discontinue use and contact your authorized Sony dealer.

In case of abnormal operation

•If the unit emits smoke or an unusual smell,

•If water or other foreign objects enter the cabinet, or

•If you drop the unit or damage the cabinet:

1 Disconnect the camera cable and the connecting cables.

2 Contact your authorized Sony dealer or the store where you purchased the product.

Operating Precautions

Operating or storage location

Avoid operating or storing the camera in the following locations:

•Extremely hot or cold places

•Exposed to direct sunlight for a long time, or close to heating equipment (e.g., near heaters)

•Close to sources of strong magnetism

•Close to sources of powerful electromagnetic radiation, such as radios or TV transmitters

•Locations subject to strong vibration or shock

Ventilation

To prevent heat buildup, do not block air circulation around the camera.

Transportation

When transporting the camera, repack it as originally packed at the factory or in materials of equal quality.

Cleaning

•Use a blower to remove dust from the lens or optical filter.

•Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn stains can be removed using a soft cloth dampened with a small quantity of detergent solution, then wipe dry.

•Do not use volatile solvents such as alcohol, benzene or thinners as they may damage the surface finishes.

Overview

How to Use This User’s Guide / Precautions 7

Overview

System Requirements

These are the requirements for the computer that displays the image or controls the camera.

Processor

Pentium III 1 GHz or higher (Pentium 4, 2 GHz or higher recommended)

RAM

256 MB or more

OS

Windows 2000/XP

Web browser

Internet Explorer Ver. 5.5 or Ver.6.0

8 System Requirements

Preparation

The Preparation section explains what the administrator has to prepare for monitoring the images after installation and connection of the camera.

Assigning the IP Address to the Camera

To connect the camera to a network, you need to assign a new IP address to the camera when you install the camera for the first time.

You can assign an IP address in two ways:

•Using the setup program stored in the supplied CDROM (see page 9)

•Using the ARP (Address Resolution Protocol) commands (see page 75)

This section explains how to assign an IP address to the camera using the supplied setup program and how to configure the network.

Before starting, connect the camera to a local network, referring to “Connections” in the supplied Installation Manual.

Consult the administrator of the network about the assigned IP address.

Assigning the IP Address Using the

Setup Program

1 Insert the supplied CD-ROM disc into your CDROM drive.

After a short time a window will open displaying the files on the CD-ROM.

2 Click the Setup icon of IP Setup Program. The “File Download” dialog opens.

3 Click Open.

Note

If you click “Save this program to disk” on the “File Download” dialog, you cannot install correctly. Delete the downloaded file, and click Setup icon again.

4 Install the IP Setup Program to your computer following the wizard displayed.

If the Software License Agreement is displayed, read it carefully and accept the agreement to continue the installation.

5 Start the IP Setup Program.

The program detects the SNC-RZ25N or SNCRZ25P cameras connected to the local network and lists them on the Network tab window.

6 Click on the camera to which you want to assign a new IP address in the list.

The network settings for the selected camera are displayed.

7 Set the IP address.

To obtain the IP address automatically from a DHCP server:

Select Obtain an IP address automatically.

The IP address, Subnet mask and Default gateway are assigned automatically.

Preparation

Assigning the IP Address to the Camera	9

To specify the IP address manually:

Select Use the following IP address, and type the IP address, Subnet mask and Default gateway in the relevant boxes.

Preparation	8 Set the DNS server address.
	To obtain the DNS server addresses
	automatically:
	Select Obtain DNS server address automatically.

To specify the DNS server addresses manually: Select Use the following DNS server address, and type the Primary DNS server address and Secondary DNS server address in the relevant boxes.

Note

The Third DNS server address and Fourth DNS server address are invalid for this camera.

9 Set the HTTP port No.

Normally select 80 for the HTTP port No. To use another port number, select the text box and type a port number between 1024 and 65535.

10 Type the Administrator name and Administrator password.

The default settings of both items are “admin.”

Note

You cannot change the Administrator name and Administrator password in this step. To change these items, See “Setting the User — User setting Menu” on page 44.

11 Confirm that all items are correctly set, then click

OK.

If “Setting OK” is displayed, the IP address is correctly assigned.

12 To access the camera directly, double-click the camera name on the list.

Tip

The factory setting of the camera network is as follows.

IP address: 192.168.0.100 Subnet mask: 255.0.0.0

Wireless LAN setting

Type: Adhoc SSID: snc-rz25 Channel: 11 ch WEP: Nothing

The welcome page of the network camera SNCRZ25N or SNC-RZ25P is displayed.

Note

If the IP address is not set correctly, the welcome page does not appear after step 12. In this case, try to set the IP address again.

10 Assigning the IP Address to the Camera

Accessing the Camera

Using the Web Browser

When the IP address has been assigned to the camera, check that you can actually access the camera using the Web browser installed in your computer.

Use Internet Explorer as the Web browser.

1 Start the Web browser on the computer and type the IP address of the camera in the URL box.

The welcome page of “Network Camera SNCRZ25N” or “Network Camera SNC-RZ25P” is displayed.

2 Click Enter.

The main viewer is displayed.

When the main viewer is correctly displayed, the IP address assignment is completed.

When the main viewer of the camera is displayed for the first time

When you click Enter, “Security warning” is displayed. When you click OK, the ActiveX control is installed and the main viewer is displayed.

Notes

•If Automatic configuration is enabled in the Local Area Network (LAN) Settings on Internet Explorer, the image may not be displayed. In this case, disable

Automatic configuration and set the Proxy server manually. For setting the Proxy server, consult your network administrator.

•When you install ActiveX viewer on Windows 2000 or Windows XP, you should have logged in the computer as the Administrator.

Tip

Every page of this software is optimized as display character size Medium for Internet Explorer.

To display the Welcome page correctly

To operate the welcome page correctly, set the security level of the Internet Explorer to Medium or lower, as follows:

1 Select Tool from the menu bar for Internet Explorer, then select Internet Options and Security tab in sequence.

2 Click the Internet icon (when using the camera via the Internet) or Local intranet icon (when using the camera via a local network).

3 Set the slider to Medium or lower. (If the slider is not displayed, click Default Level.)

Preparation

Accessing the Camera Using the Web Browser 11

Preparation

When using antivirus software in the computer

•When you use antivirus software in your computer, the camera performance may be reduced, for example, the frame rate for displaying the image may be lower.

•The Web page displayed when you log in the camera uses Java Script. The display of the Web page may be affected if you use antivirus software in your computer.

12 Accessing the Camera Using the Web Browser

Basic Configuring by the

Administrator

You can monitor the image of the camera only logging in with the initial condition of this network camera. You can also set various functions according to the install position, network condition or purpose of the camera. We recommend you configure the following items before monitoring the image from the camera.

Setting contents	Setting menu
Flip the image according to the installation position (desk top or ceiling).	Image flip (page 35)
Set the format of the image sent from the camera (MPEG 4 or JPEG).	Video mode (page 34)
Select the white balance mode according to the installing position (indoor or	White balance (page 36)
outdoor).
Select the brightness of the image sent from the camera.	Exposure mode (page 36)
	Brightness (page 37)
Select the quality of the image sent from the camera.	MPEG4 Tab (page 38)
	JPEG Tab (page 38)
Select the size of the image sent from the camera.	Image size (page 35)
Select weather the audio from the external microphone is sent or not.	Microphone (page 36)
Accord date and time of the camera with those of the computer.	Date & time Tab (page 32)
Make the setting for sending the monitor image attached to a mail.	e-Mail (SMTP) setting Menu (page 46)
Set the access right of the user for the camera.	Security setting Menu (page 45)
Set a place to see beforehand.	Preset positin setting Menu (page 63)
Prepare a panorama image.	Creating a Panorama Imgae (page 71)

Preparation

Basic Configuring by the Administrator	13

Camera the Operating

Operating the Camera

The Operating the Camera section explains how to monitor the image from the camera using the Web browser. Use Internet Explorer as the Web browser. The functions of the camera should be set by the Administrator. For setting the camera, see “Administrating the Camera” on page 28.

Administrator and User

This network camera classifies the people who log in into the Administrator and the User.

The Administrator can use all functions of this network camera including camera setting. The functions the User can use are monitoring the image and audio from the camera, and controlling the camera. The Viewer mode setting restricts the user's access right, and the user is classified as the one of four types.

Each type of the user can use the following functions.

	Function	Administrator		User
			Full	Pantilt	Light	View
	Monitor a live image	z	z	z	z	z
	Watch date and time	z	z	z	z	z
	Control the frame rate (Usable only when JPEG mode is selected)	z	z	–	–	–
	Control the image view size	z	z	z	z	–
	Zoom a image by the digital zoom	z	z	z	z	–
	Save the still image in the computer	z	z	z	z	–
	Send an image file to the FTP server	z	z	–	–	–
	Send an image attached to a mail	z	z	–	–	–
	Record an image on the inside memory of the camera	z	z	–	–	–
	Control the Alarm out of the I/O port on the camera main unit	z	z	–	–	–
	Switch the Day/Night function mode	z	z	–	–	–
	Switch the TCP/UDP transmission mode (Available in MPEG4	z	z	–	–	–
	mode only)
	Perform the zoom operation	z	z	z	–	–
	Call the Preset position	z	z	z	–	–
	Control the audio	z	z	z	z	z
	Control the setting menu	z	–	–	–	–

z Usable function

– Not usable function

The access rights of the administrator and the user can be set in “Setting the User — User setting Menu” on the Advanced mode menu for the administrator on page 44.

14 Administrator and User

Logging in to Homepage

— Welcome Page

Logging in as a User

1 Start the web browser on the computer and type the IP address of the camera you want to monitor.

The welcome page of Network Camera SNCRZ25N or Network Camera SNC-RZ25P is displayed.

2 Select the viewer.

The usable viewers differ depending on the video mode (page 34) of the camera.

When the video mode is set to MPEG4, you can use ActiveX viewer only, and viewer selection is not possible. (MPEG4 is default. See illustration on Step 1 above.)

When the video mode is JPEG, you can select

ActiveX viewer or Java applet viewer.

For details, see “About Viewers” on page 16.

Welcome page when the video mode is JPEG

3 Select the viewer language.

Click English or Japanese at the bottom of the welcome page.

4 Click Enter.

The main viewer appears.

With the ActiveX viewer

With the Java applet viewer

Control the camera from the main viewer.

Camera the Operating

Logging in to Homepage — Welcome Page	15

Note

If the Welcome page does not activate correctly, the security level of the Internet Explorer may be set to Medium or higher. See “To display the Welcome page correctly” on page 11 and check the security level.

Displaying the setting window for the administrator directly

When the administrator sets the camera functions, the setting window can be displayed directly from the welcome page.

1 Click Setting on the welcome page. The following dialog appears.

Camera the Operating

2 Enter the user name and password for Administrator, then click OK.

The user name “admin” and the password “admin” are set at the factory for the Administrator. You can change them on the User setting menu in the Advanced mode menu (see page 44).

The Advanced mode menu appears.

About Viewers

You can use the following viewer according to the Video mode setting in the camera setting menu on the Advanced mode menu (page 34).

ActiveX viewer

This viewer can monitor the image in both video modes

MPEG4 and JPEG.

You have to install it when you access to the main viewer at the first time.

When you are going to display the main viewer of the camera for the first time

When you log in the network camera using ActiveX viewer for the first time (clicking Enter to enter the main viewer), the Security Warning appears. Click Yes and install ActiveX Control. You can use all the functions of the viewer by using ActiveX Control.

Java applet viewer

You can select this viewer when the camera video mode is set to JPEG. The frame rate is lower than the ActiveX viewer.

The Java applet viewer operates only when Java is installed and Java (Sun) is enabled. If it does not operated correctly, check if the specified Java version has been installed successfully and Java (Sun) is enabled.

To check the Java version

Select Tool from the menu bar of Internet Explorer, then select Internet Option and the Advanced mode tab in sequence, and check the version of Java displayed in Java (Sun) is one of the versions specified below. If the item Java (Sun) is not displayed, Java is not installed. You need to install Java.

Java Plug-in Ver. 1.4.2_01, Ver. 1.4.2_02, Ver. 1.4.2_03,

Ver. 1.4.2_04

To enable Java Plug-in

Check “Use Java2v1.4.2_xx for <applet> (requires restart)” in “Java (Sun)”.

To install Java Plug-in

Download Java 2 Runtime Environment, Standard Edition (JRE) from the homepage of Sun Microsystems, Inc., and install it following the instructions on the installer.

Notes

•If Automatic configuration is enabled in the Local Area Network (LAN) Settings on Internet Explorer, the image may not be displayed. In this case, disable

Automatic configuration and set the Proxy server manually. For setting the Proxy server, consult your network administrator.

•When you install ActiveX viewer on Windows 2000 or Windows XP, you should have logged in the computer as the Administrator.

16 Logging in to Homepage — Welcome Page

Tip

Every page of this software is optimized as display character size Medium for Internet Explorer.

Configuration of Main

Viewer

This section explains the functions of the parts and controls of the main viewer. For a detailed explanation on each part or control, see the specified pages.

Main viewer

MPEG4 mode*

Camera the Operating

Camera control	Monitor image	Main menu
section	section

JPEG mode*

Camera control	Monitor image	Main menu
section	section

*Refer to the “Camera setting Menu” about the Video mode (page 34).

Main menu

Setting

Click this button to display the setting menu for Administrator. (See “This section explains the basic operations and each option of the the Administrator menu.” on page 28.)

Configuration of Main Viewer	17

Camera the Operating

You can operate this function only when logging in as the administrator.

Home

Displays the Welcome page.

Player

Click this button to download the “SNC video player” application program built in the camera. The SNC video player allows you to play video/audio data recorded on the camera with your computer. (See “Using the SNC video player — Playing Video/Audio File Recorded on Camera” on page 70.)

Camera Control Section

Frame rate

(Displayed only when the camera Video mode (page 34) is set to JPEG.)

Selects the frame rate to transmit images.

View size

Selects the view size to be displayed. (page 20)

Digital zoom

Click to change the size of the digital zoom. (page 20)

Capture

Click this button to capture a still image shot by the camera and to store it in the computer. (See “Capturing a Monitor Image” on page 21.)

Control

Click this icon to operate the camera using the PanTilt and Zoom functions.

When you click it, the icon appears and you will be able to control PanTilt and Zoom functions from the

main viewer. (See “Controlling via the control panel” (page 22))

Preset position

Select the Preset position name from the drop-down list. Then, the camera will move to the Preset position that you have stored in memory at “Preset position” menu.

Note

The list box is not displayed when no preset position is memorized.

Control panel icon

Click this icon to display the following control panel.

Control panel

You can control PanTilt, Zoom, and Focus of the camera. (page 22).

PanTilt control

Click the arrow button of the direction in which you want to move the camera. Keep it pressed to move the camera continuously.

To return to the home position, click button.

Zoom control

Press to zoom out, and press to zoom in. Zooming continues while the button remains pressed.

Focus control

To focus on a nearby object, press . To focus on a distance object, press .

18 Configuration of Main Viewer

By pressing , the focus is set to the optimum position.

Note

To control the focus manually, set “Focus mode” of the camera setting menu to Manual. (page 36)

Trigger

(Displayed only when the camera Viewer mode (page 44) is set to Full and one or more triggers are enabled on the Trigger Setting menu (page 57).)

Select the function you want to use from the list box and click the icon. Then you can send the monitor image of the camera to an FTP server (page 25), send it attached to a mail (page 25), record the image on the built-in memory (page 25) and switch the Alarm out to On/Off (page 26).

Transmission (Switching the TCP/ UDP transmission mode)

(Displayed only when the camera Video mode (page 34) is set to MPEG4 and you are using the ActiveX viewer.)

Each click switches the transmission mode of the video/ audio data among TCP mode, UDP (Unicast) mode and UDP (Multicast) mode. (page 27)

The last selected mode is saved in the computer, and it will be selected at the next starting.

(Volume)

(Displayed when the Microphone (page 36) is set to

On.)

Drag the bar of icon to adjust the volume. When you click icon, the icon changes to and the audio output stops. To output the audio, click again.

Note

If the volume icon is not displayed in the case you are using Java applet viewer, Audio codec may not be set G.711(64kbps) (page 36) or Java may not be installed correctly.

To check if Java is installed correctly, refer to “Java applet viewer” of “About Viewers” on page 16.

Monitor Image

The image shot by the camera is shown here. Date and time is displayed at the top of the window.

Camera the Operating

Configuration of Main Viewer	19

Controlling the Monitor

Image

You can monitor the camera image on the monitor window of the main viewer.

Monitoring the camera image

1 Log in to the home page to display the main viewer. You can see how to log in on page 15, “Logging in as a User”.

Camera the Operating

2 Select the frame rate (only when the camera Video mode is set to JPEG).

Click the Frame rate list box to select the frame rate for transmitting the image. Selectable frame rates are as follows.

SNC-RZ25N

1, 2, 3, 4, 5, 6, 8, 10, 15, 20, 25, 30

SNC-RZ25P

1, 2, 3, 4, 5, 6, 8, 10, 15, 20, 25

The number refers to the frame number transmitted per 1 second.

For example, if you select 30 fps in SNC-RZ25N, the image is sent at the maximum speed of the connected line (30 fps maximum).

Note

The frame rate options indicate the maximum number of frames that can be transmitted.

The number of frames actually transmitted may vary depending on network environments and camera settings (image size and image quality settings).

3 Select the view size.

Click View size box list box to select the view size from among Auto, 640 × 480, 320 × 240 and 160 × 120.

Auto is determined by the image size specified with Image size on the Camera setting page (page 35).

Zooming in the monitor image

1 Click Digital zoom icon.

2 Click the point you want to zoom in.

The image is expanded by about 1.5 times with the clicked point at the center.

The digital zoom icon changes to .

3 To cancel zooming in, click icon.

20 Controlling the Monitor Image

Capturing a Monitor

Image

You can capture a monitoring image as a still image and save it in the computer.

Capturing a monitor image

1 Monitor the camera image in the monitor window.

2 Click Capture icon.

The still image of the moment when you click is captured, and the still image is displayed in the monitor window.

With the ActiveX viewer

With the Java applet viewer

Saving the captured image

With the ActiveX viewer

1 Capture the monitor image.

2 Click Save.

Save As dialog appears.

3 Select JPEG or Bit map as Save as type.

4 Type on File name and specify Save in, then click

Save.

With the Java applet viewer

1 Capture the monitor image.

2 Right-click the mouse to display the menu and select Save with a new name.

Save Picture dialog appears.

Camera the Operating

3

4

Select JPEG or Bit map as Save as type.

Type in File name and specify Save in, then click

Save.

3 To cancel the still image, click Cancel or Close.

Capturing a Monitor Image	21

Camera the Operating

Operating the camera

You can operate the camera from the main viewer.

When you click control icon, the display switches to control panel icon. PanTilt mark and Preset list

box are displayed on the upper right of the window.

Notes

When mark is displayed at upper right side of the window, you can use Pan/Tilt control function. And by executing the digital zoom when you can control it, mark turns gray and you cannot control the camera in the monitor window or in the panorama window, or cannot control zoom in the zoom bar.

By canceling the digital zoom, mark returns to white.

•The PRESET list box is not displayed when no preset position is memorized.

•When Exclusive control mode of “System setting

Menu” is set to On and when you click the control icon, the remaining time of operation authority is displayed. If you cannot get the authority to control,

waiting time icon appears and the waiting time is displayed.

Operating by using the Control panel

You can operate the camera direction, Zoom, and Focus by using the control panel for the monitor image currentry displayed.

Controlling via the control panel

1 Click control icon.

The control panel icon is displayed.

2 Click control panel icon. The control panel is displayed.

3 Control each function using the displayed control panel.

Pantilt control

Click the arrow button of the direction in which you want to move the camera. Keep it pressed to move the camera continuously.

To return to the home position, click button.

Zoom control

Press to zoom out, and press to zoom in. Zooming continues while the button remains pressed.

Focus control

To focus on a nearby object, press . To focus on a distance object, press .

By pressing , the focus is set to the optimum position.

Note

To control the focus manually, set “Focus mode” of the camera setting menu to Manual. (page 36)

Control the camera in the monitor window

Click on the monitor image, and the camera moves so that the clicked portion goes to the center of the display.

Dragging the mouse on the window draws a red frame. If you drag the mouse to box the point you want to

22 Operating the camera

watch, the direction and the zoom position of the camera move to suit to the red frame.

Still image

Red zooming frame Click the left button of the mouse on the still image and drag it.

Zoom an image by the camera zoom bar

When you can control this function, the zoom bar is displayed below the window.

You can specify a location to be zoomed by clicking the zoom bar.

The zoom bar is displayed /not displayed by clicking the icon below the image frame.

Optical WIDE marge icon: Click to move the zoom to the optical WIDE Merge (the same magnification).

Optical TELE marge icon: Click to move the zoom to the optical TELE Merge (18-fold magnification).

Digital TELE marge icon: Click to move the zoom to the digital TELE Merge (216-fold magnification)

Not to display the zoom bar

When you are not going to use the zoom bar, it is not displayed by pressing button under the panorama window.

Note

The zoom bar of the digital area is not displayed when the “Zoom mode” of the camera setting menu is not set to Full.

Moving the camera to the preset position

PRESET list box

Select the preset position name from the drop-down list. Then, the camera will move to the preset position that you have stored in memory at “Preset position setting Menu”.

Camera the Operating

Operating the camera 23

Camera the Operating

The camera is moved to face toward the clicked

Controlling the camera	point, and the present image of the point is
on a panorama image	displayed in the normal camera widow.

When you can control the camera, the panorama widow is displayed under the normal camera window.

Normal camera window

SNC-RZ25N/P

Click the point you want to watch.

The present situation is displayed at the clicked point.

panorama window

In the panorama window, an image of 360° around the camera is displayed as a panorama image. When you click on the displayed panorama image, the camera faces the clicked place.

Not to display the panorama window

When you are not going to use the panorama image, pressing under the panorama window twice prevents its display.

Creating the panorama image

Create the panorama image with the supplied “SNC panorama creator”. Refer to page 71 for details.

Tip

The panorama image is the still image converted from the image taken when you were going to create a panorama image with “SNC panorama creator”. When the camera is moved or when the layout around the camera is changed, create the panorama image again.

Facing the camera toward the specified point

1 Create a panorama image with “SNC panorama creator” and display it.

2 Click the point you want to watch on the panorama image.

24 Controlling the camera on a panorama image

Sending an Image File

You can send a captured still image with an attached mail or to the FTP server.

To use this function, you need to make the e- Mail(SMTP) and FTP client active, and set the address properly in the Trigger setting menu on the Administrator menu (page 57).

Sending a Monitor Image via E-mail

1 Monitor the image on the monitor window.

2 Select e-Mail from the Trigger list box.

3 Click Trigger icon.

The still image of the moment when you click is captured, and the mail attached with the image file is sent to the mail address you have set.

Sending a Monitor Image to an FTP Server

1 Monitor the image on the monitor window.

2 Select FTP from the Trigger list box.

3 Click Trigger icon.

The still image of the moment when you click is captured, and the image file is sent to the FTP server.

Recording a Still Image

in the Memory of the

Camera

You can capture a camera image as a still image and record it in the memory of the camera. “Memory” contains Built-in memory and CF memory card, and you can select one of them in the setting window.

To use this function, you need to make Image memory active and to set details of the image memory in the trigger setting menu on the Administrator menu

(page 57).

1 Monitor the image on the monitor window.

2 Select Image memory from the Trigger list box.

3 Click Trigger icon.

The still image of the moment when you click is captured, and the image file is recorded in the memory of the camera.

Camera the Operating

Sending an Image File / Recording a Still Image in the Memory of the Camera	25