6
Electric Fireplace SEKU 2000 A1
KOMPERNASS GMBH
BURGSTRASSE 21 · D-44867 BOCHUM
www.kompernass.com
ID-Nr.: SEKU 2000 A1-05/10-V3
Electric Fireplace
Operating instructions
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . 2
Information for these operating instructions . . . . . 2
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Limited liability . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Risk of electrocution . . . . . . . . . . . . . . . . . . . . . . . 4
Basic Safety Instructions . . . . . . . . . . . . . . . . . . . . 4
Setting up and connecting . . . . . . . . . . . 5
Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Items supplied and delivery checks . . . . . . . . . . .5
Disposal of the packaging . . . . . . . . . . . . . . . . . . 5
Installation requirements . . . . . . . . . . . . . . . . . . . . 6
Before the fi rst use . . . . . . . . . . . . . . . . . . . . . . . . .6
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . 6
Operating components . . . . . . . . . . . . . 7
Set up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Individual parts of the electric fi replace . . . . . . . . 8
Screws and assembly material . . . . . . . . . . . . . . .9
GB
IE
Assembly . . . . . . . . . . . . . . . . . . . . . . . . 10
Handling and operation . . . . . . . . . . . 14
Switching the appliance on and off . . . . . . . . . .14
Maintenance . . . . . . . . . . . . . . . . . . . . . 14
Changing the light bulbs . . . . . . . . . . . . . . . . . . .14
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . 15
Troubleshooting . . . . . . . . . . . . . . . . . . 15
Malfunction causes and remedies . . . . . . . . . . .16
Storage/Disposal . . . . . . . . . . . . . . . . . 16
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Disposal of the appliance . . . . . . . . . . . . . . . . . .16
Appendix . . . . . . . . . . . . . . . . . . . . . . . 17
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Notes on the EC Declaration of Conformity . . . .17
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Importer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
SEKU 2000 A1
1
Introduction
GB
IE
Introduction
Information for these operating instructions
These operating instructions are a component of the SEKU 2000 A1 Electric Fireplace (henceforth designated
as the appliance) and they provide you with important information about the intended use, safety, installation
and connection as well as operation of the appliance.
These operating instructions must at all times be kept available close to the appliance. They are to be read
and applied by everyone assigned to install, service and repair faults in the appliance.
Keep these operating instructions and hand them over with the appliance to any future owners.
Copyright
This documentation is copyright protected.
Any copying or reproduction of this handbook, including extracts, as well as the rendering of any images,
even in an altered state, is permitted only with the written consent of the manufacturer.
Limited liability
All technical information, data and instructions for installation, connection and operation contained in these
operating instructions correspond to the status at the time of printing and, to the best of our knowledge, take
into account our previous experience and know-how.
No claims can be derived from the details, illustrations and descriptions in these instructions.
The manufacturer assumes no liability for damage caused by failure to observe these instructions, improper
use, inappropriate repairs, making unauthorized modifi cations or for using unapproved replacement parts.
2
SEKU 2000 A1
Introduction
Warnings
In these operating instructions the following warnings are used:
DANGER
A warning at this danger level indicates a threateningly dangerous situation.
If the dangerous situation is not avoided, it could result in death or serious injury.
►
Compliance with the instructions in this warning is necessary to avoid the risk of death or serious injury.
WARNING
A warning at this danger level indicates a potentially dangerous situation.
If the dangerous situation is not avoided it can lead to injuries.
►
The directives in this warning are there to avoid personal injuries.
IMPORTANT
A warning of this danger level signifi
If the situation is not avoided it can lead to property damage.
►
The directives in this warning are there to avoid property damage.
GB
IE
es possible property damage.
NOTICE
A notice signifi es additional information that assists in the handling of the appliance.
►
Intended use
This appliance is intended for the heating of enclosed living spaces. In addition, artifi cial fi re fl ares can be
created with the appliance to optically replicate an open-hearth fi re.
This appliance is not intended for any other use or for uses other than those mentioned.
WARNING
Risks from unintended use!
Risks can be created by the appliance if it used for unintended purposes and/or for other applications.
►
Use the appliance exclusively for its intended purposes.
Observe the procedures described in these operating instructions. ►
Claims of any kind for damage resulting from unintended use will not be accepted.
The operator alone bears the liability.
SEKU 2000 A1
3
Safety
GB
IE
Safety
In this chapter you are being given important safety information regarding the handling of the appliance.
This appliance complies with the statutory safety regulations. Incorrect usage can, however, lead to personal
and property damage.
Risk of electrocution
DANGER
Risk of electrocution!
A potentially fatal situation can arise from contact with live wires or components!
Pay heed to the following precautions to avoid the risk of electric shock:
►
Do not use the appliance if the mains power plug or the connecting cable are damaged.
Before continuing to use the appliance, arrange for the connecting cable to be replaced by ►
authorised qualifi ed persons.
►
Do not, under any circumstances, open the appliance housing. There is the risk of receiving
an electric shock if the power carrying connections are touched and/or the electrical and
mechanical construction is changed.
Do not cover the appliance!
Covering the appliance can cause overheating and thus lead to
the development of a fi re!
Basic Safety Instructions
For safe handling of the appliance observe the following safety information:
Before use check the appliance for visible external damage. Do not put into operation a appliance that is
■
damaged or has been dropped.
Arrange for damaged cables or connections to be replaced by authorized qualifi ed persons or by the
■
Customer Service department.
Persons who, due to their physical, intellectual or motor abilities, are incapable of operating the appliance
■
safely may only use the appliance under supervision or direction from a responsible person.
Only permit children to use the appliance under supervision.
■
Repairs should only be carried out by authorized specialist companies or by the customer service department. ■
Incorrect repairs can result in signifi cant dangers for the user. In addition warranty claims become void.
During the warranty period repairs to the appliance may only be carried out by a Customer Service
■
department authorised by the manufacturer, if they are not, no additional warranty claims can be
considered for subsequent damages.
4
SEKU 2000 A1
Setting up and connecting
Defective components may only be replaced with original replacement parts. Only by using original ■
replacement parts can it be guaranteed that the safety requirements are being complied with.
Protect the appliance from moisture and liquid penetration.
■
Always pull on the plug when disconnecting from the mains power socket, never pull on the connection cable. ■
Do not use the appliance adjacent to open fl ames. ■
If malfunctions occur or thunder storms threaten, remove the plug from the mains power socket. ■
Never subject the appliance to spray and/or dripwater, do not place any objects fi lled with liquid ■
(i.e. vases), or fi lled drink glasses, on or next to the appliance.
Setting up and connecting
Safety Notices
WARNING
During commissioning of the appliance, damage may occur to persons and property!
Pay heed to the following safety information to avoid these risks:
►
Packaging material should not be used as a play thing. There is a risk of suff ocation.
Comply with the notices in regard to the requirements for the installation site and for the electrical ►
connection to avoid risks for people and property.
GB
IE
Items supplied and delivery checks
The appliance is delivered with the following components as standard:
Electric Fireplace
▯
Lightbulbs, 2 x E14, max. 25 W (preinstalled) ▯
Fireplace panelling including assembly material ▯
Operating instructions ▯
NOTICE
Check the contents to make sure everything is there and for visible damage.
►
If the contents are incomplete, or are damaged due to defective packaging or transportation, contact ►
the Service Hotline (see warranty card).
Disposal of the packaging
The packaging protects the appliance from transport damage. The packaging materials are selected from
the point of view of their environmental friendliness and disposal technology and are therefore recyclable.
The recirculation of packaging into the material circuit saves on raw material and reduces generated waste.
Dispose of packaging material that is no longer needed according to the regionally established regulations.
NOTICE
If possible preserve the appliance's original packaging during the w
of a warranty claim you can package the appliance properly for return.
SEKU 2000 A1
arranty period so that in the case ►
5
GB
IE
Installation requirements
For the safe and correct operation of the appliance, the installation site must satisfy the following requirements:
The appliance must be placed on a fi rm, fl at and horizontal surface.
■
Do not place the appliance in a hot, wet or very humid environment or close to infl ammable materials. ■
The mains power socket must be easily accessible at all times, thus enabling the plug to be immediately ■
withdrawn should an emergency situation arise.
Ambient temperature range: +5 to +45 °C
■
Humidity (No condensation): 5 - 90 % ■
DANGER
Fire hazard due to material contact!
If the heater makes contact with fl ammable materials, there is a risk of fi re!
Pay heed to the following safety information to avoid these fi re risks:
►
Keep infl ammable materials well away from the place of installation of the appliance.
Prevent the physical contact of combustible materials (e.g. textiles) with the appliance. ►
Do not cover the warm air outlet openings of the appliance. ►
Setting up and connecting
Before the fi rst use
Remove all packaging materials and transport restraints from the appliance. ■
NOTICE
When you fi rst use it, it may temporarily generate a light odour. This is normal and completely harmless.
►
Electrical connection
For a safe and correct operation of the appliance, take note of the following instructions regarding the
electrical connection:
Before you connect the appliance, compare the connection data (voltage and frequency) on the plate
■
with that of your electricity supplier. This data must tally, in order to avoid damage to the appliance.
Ensure that the power cable is undamaged and that it is not placed over hot surfaces and/or sharp edges.
■
The connecting cable must not be taut. ■
6
SEKU 2000 A1
Operating components
Operating components
NOTICE
The operating elements are on the front of the appliance, above right and behind the ventilation grille.
►
To operate them, fold the ventilation grille forward. ►
GB
IE
ON/OFF switch (Flames)
2
ON/OFF switch (Heating, level 1)
3
ON/OFF switch (Heating, level 2)
4
Temperature control (Thermostat)
5
Dimmer (for fl ame lamps)
SEKU 2000 A1
4
3
2
5
7
Set up
GB
IE
Set up
Before the appliance can be set up, the fi re surround must be assembled.
NOTICE
Check the contents to make sure everything is there and for visible damage.
►
Firstly, become familiar with all parts involved in the assembly. ►
Individual parts of the electric fi replace
2
5
3
4
8
left side panel
2
left front panel
3
top covering panel
4
right front panel
5
centre front panel
6
Base plate
7
Floor plate
8
right side panel
6
7
8
SEKU 2000 A1
Set up
Screws and assembly material
GB
IE
A
B
C
D
E
No.: Designation: Number:
A
Screws 6 x 25 mm 17
B
Wood plugs 8
C
Double locking pin 4
D
Single locking pin 6
E
Adapter sleeve 14
F
Fixing device 2
NOTICE
You require a screwdriver for the assembly; this is not supplied.
►
The assembly of the fi re surround is described in detail in the following.
F
NOTICE
Carry out the assembly step by step in the order as described.
►
SEKU 2000 A1
9
Assembly
GB
IE
Assembly
Step 1
Screw three single locking pins
Place two wood plugs
Insert three adapter sleeves
screwdriver line up the adaptor sleeves
edge of the side panel .
D
with a screwdriver into the prepared holes on the left front panel 2.
B
into the holes of the front panel 2.
E
into the three large holes of the left side panel . Thereby, with the
E
so that the arrow on the adaptor sleeves points to the outer
D
B
2
D
D
E
Then, bring the front panel
2
and side panel together at right angles, so that the locking pins D
enter the holes on the left edge of the side panel .
When done, screw all three adapter sleeves
E
to the right with the screwdriver until the locking pins are
clamped into the adapter sleeves and the panels are seated fi rmly together and at right angles.
Step 2
Screw three single locking pins
Place two wood plugs
Insert three adapter sleeves
B
D
with a screwdriver into the prepared holes on the right front panel 4.
into the holes of the front panel 4.
E
into the three large holes of the right side panel 8. Thereby, with the
screwdriver line up the adaptor sleeves E so that the arrow on the adaptor sleeves points to the outer
edge of the side panel 8.
D
8
D
E
B
4
10
D
SEKU 2000 A1
Assembly
Then, bring the front panel
4
and side panel 8 together at right angles, so that the locking pins D
enter the holes on the right edge of the side panel.
When done, screw all three adapter sleeves
E
to the right with the screwdriver until the locking pins are
clamped into the adapter sleeves and the panels are seated fi rmly together and at right angles.
Step 3
Take the centre front panel
Then place four adapter sleeves
5
and lay it face down.
E
in the four large holes. Turn the adapter sleeves with the screwdriver
so that the arrows on the adapter sleeves each point to the outer edge of the centre front panel 5.
Insert four double locking pins
sleeves
E
with the screwdriver to the right until the locking pins are fi rmly secured.
C
C
in the upper holes on the front sides of the panel and turn the adapter
C
E
GB
IE
5
Step 4
Now connect the so prepared centre front panel
For this, insert two adapter sleeves
E
in the large holes in the side panels. Turn the adapter sleeves E
5
with the side panels prepared in steps 1 and 2.
with the screwdriver so that the arrows on the adapter sleeves each point to the outer edge of the side
panels.
Then, guide each of the double locking pins
C
of the centre front panel 5 into the corresponding holes
in the edges of the side panels.
When done, turn all four adapter sleeves
E
in the centre front panel 5 with the screwdriver to the right,
until all parts are at right angles to each other and fi rmly tightened.
E
5
E
SEKU 2000 A1
11
GB
IE
Assembly
Step 5
Place the fl oor plate
Now take the previously assembled unit and carefully place it on the fl oor plate as shown in the following
diagramme.
Then screw together the assembled unit with the connection blocks
8 screws of the type A. (2 screws per connection block).
7
on the fl oor.
G
on the fl oor plate 7. For this, use
G
G
Step 6
Take the top covering panel
Secure the top covering panel
A
A
3
and place it on the preassembled unit.
3
from the inner side of the unit with 7 screws of the type A.
3
A
12
SEKU 2000 A1
Assembly
Step 7
Take the base plate
Then place the base plate
the fl oor plate.
Rear view Front View
6
and insert 4 wood plugs B into the holes of the plate underside.
6
on the fl oor plate 7 so that the four wood plugs fi t into the four holes in
6
GB
IE
B
B
7
Installing the appliance in the fi re surround
To fi nalise, install the appliance in the assembled fi re surround.
Place the appliance carefully on the base plate (from the rear of the fi re surround) and then push it
gently forward as far as it will go into the opening of the fi re surround.
Secure the appliance to the fi re surround at the edges with the fi xing devices
6 x 25 mm A.
Insert the plug into the mains power socket.
F
and the screws
F
WARNING
Improper laying of the power cable can cause damage to people and property!
Pay heed to the following safety information to avoid these risks:
►
Do not bend or clamp the power cable and do not lay it tautly.
Do not run the power cable over sharp edges. ►
SEKU 2000 A1
A
13
Handling and operation/Maintenance
GB
IE
Handling and operation
NOTICE
See also "Operating Elements" on page 7.
►
In this chapter you receive important information for the handling and operation of the appliance.
Activate the ON/OFF switch
to turn the unit on. The fl ame replication lights up. Programme in the
5
desired brightness with the Dimmer
Then, turn the heater on with the switch
1 (1000 W).
Activate the additional switch
Using the thermostat
after reaching the set temperature range, and switch back on when it becomes cooler.
4
, you can set it to the desired temperature. The heat settings switch themselves off
.
3
; the heating is now working at level 2 (2000 W).
Switching the appliance on and off
Activate the ON/OFF switch to turn the appliance on.
Activate the ON/OFF switch
once again to turn the appliance off .
Maintenance
2
; the built-in fan starts to run and the heater is working at level
The maintenance of the appliance is limited to occasional external cleaning.
NOTICE
Keep the appliance, and in particular the ventilation grille, free from dust and dirt.
►
Changing the light bulbs
DANGER
Risk of electrocution!
Contact with electricity can be fatal!
Pay heed to the following safety information to avoid the risks of injury:
►
Switch the appliance off .
Before changing the bulb, unplug the appliance from the mains power source. ►
WARNING
Risk of injury from sharp edges!
When reaching in through the housing opening, there is a risk of injury from the
sharp edges on sheet metal housing and the refl ector mirrors.
Pay heed to the following safety information to avoid these risks:
►
Do not touch the edges of the housing and the refl ector mirror
►
Wear protective gloves if necessary.
11
.
14
SEKU 2000 A1
Maintenance/Cleaning/Troubleshooting
Switch the appliance off .
Pull the plug from the mains power socket.
Loosen the four screws on the rear panel and remove the metal ventilation panel
Carefully replace the defective bulb
Screw the metal ventilation panel
10
in the light shaft.
9
back onto the appliance rear.
11
10
9
GB
9
.
IE
Cleaning
WARNING
Observe the following safety information to avoid risks and property damage:
►
Clean the appliance ONLY when it is switched off and cold.
IMPORTANT
Possible damage to the appliance.
enetrating moisture can cause damage to the appliance.
P
►
In order to avoid irreparable damage, when you are cleaning the appliance ensure that moisture
cannot get inside it.
■
Clean the housing exclusively with a soft damp cloth and a mild dishwashing liquid.
Troubleshooting
In this chapter you will receive important information for the localisation of malfunctions and remedies for them.
Observe these instructions in order to avoid risks and damage.
WARNING
Observe the following safety information to avoid risks and property damage:
Repairs to electrical appliances may only be carried out by specialists who have been trained by the ►
manufacturer. Considerable risk for the user and damage to the appliance can occur as a result of
incorrect repairs.
SEKU 2000 A1
15
GB
IE
Troubleshooting/Storage/Disposal
Malfunction causes and remedies
The following table will help with localising and remedying minor malfunctions:
Defect Possible cause Solution
The appliance is not switched on. Switch the appliance on.
The fl ame replication does
not light up.
The appliance does not heat.
The fan does not run.
The heating is not switched off .
NOTICE
If you cannot solve the problem with the aforementioned methods, please contact Customer Services.
►
The plug is not inserted.
The mains power socket does
not supply voltage
The bulbs are defect. Replace the defective bulbs.
Switch
Switch 2 is not turned on.
Switch 3 is not turned on.
Heating level control defective
Switch
Switch
Fan defect.
Thermostat
Temperature control
is not turned on.
is not turned on.
2
is not turned on.
4
falsely adjusted.
4
defect.
Insert the plug into the
mains power socket.
Check the fuses
Switch on.
Switch 2 on.
Switch 3 on.
Inform Customer Services.
2
on.
on.
Switch
Switch
Inform Customer Services.
Set the thermostat 4 at the
required temperature.
Inform Customer Services.
Storage/Disposal
Storage
Disconnect the plug if you are not intending to use the appliance for a long period.
Store the appliance at a dry locality.
Disposal of the appliance
Do not dispose of the apliance in your normal domestic waste. This product is subject to
the provisions of European Directive 2002/96/EC-WEEE (Waste Electrical and Electronic
Equipment).
Dispose of the appliance through an approved disposal centre or at your community waste facility.
Observe the currently applicable regulations. In case of doubt, please contact your waste disposal centre.
16
SEKU 2000 A1
Appendix
Appendix
Technical data
General
Input voltage 220 - 240 V
Mains frequency 50 Hz
Power consumption
Heating level 1
Heating level 2
Bulb
2 x Bulbs E14
Ambient temperature +5 to +45 °C
Humidity (no condensation) 5 to 90 %
Measurements (W x H x D): 100 x 100 x 39 cm
1000
2000
2 x 25 W
W
W
GB
IE
~
Weight approx. 45 kg
Notes on the EC Declaration of Conformity
This appliance complies with, in regard to conformance to the basic requirements and other
relevent regulations, the European Directive Low Voltage Directive 2006/95/EC as well
as the European Directive for Electromagnetic Compatibility 2004/108/EC.
The complete original declaration of conformity can be obtained from the importer
SEKU 2000 A1
17
GB
IE
Appendix
Warranty
You receive a 3-year warranty for this appliance as of the purchase date. The appliance has been manufactured with care and meticulously examined before delivery.
Please retain your receipt as proof of purchase. In the case of a warranty claim, please make contact by
telephone with our Service Department. Only in this way can a post-free despatch for your goods be assured.
NOTICE
The warranty is valid only for material or manufacturing defects not, however, for transport damage, ►
wear and tear or for damage to breakable parts, i.e. switches or rechargeable batteries..
This product is for private use only and is not intended for commercial applications. The warranty becomes
void in the event of abusive and improper handling, use of force and internal tampering not carried out by
our authorised service branch.
Your statutory rights are not restricted in any way by this warranty. The warranty period will not be extended
as a result of repairs made under warranty. This applies also to replacement and repaired parts.
Damages and defects potentially present at the time of purchase must be reported immediately after
unpacking or, at the very least, two days after the date of purchase.
Repairs carried out after expiry of the warranty period are subject to payment.
Service
DES UK LTD
Tel.: 0871 5000 700
e-mail: support.uk@kompernass.com
Kompernass Service Ireland
Tel: 1850 930 412 (0,082 EUR/Min.)
Standard call rates apply. Mobile operators may vary.
e-mail: support.ie@kompernass.com
Importer
KOMPERNASS GMBH
BURGSTRASSE 21
44867 BOCHUM, GERMANY
www.kompernass.com
(£ 0.10 / minute)
18
SEKU 2000 A1
Loading...