Samsung SDH-B3020, SDH-B3040, SDH-C5100 User Manual

4/16 CHANNEL DVR

User Manual

SDH-B3020 SDH-B3040 SDH-C5100

4/16 Channel DVR

User Manual

Copyright

©2014 Samsung Techwin Co., Ltd. All rights reserved.

Trademark

is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd.

Other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.

Disclaimer

Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user's own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.

Design and specifications are subject to change without prior notice.

The initial administrator ID is “admin” and the password should be set when logging in for the first time.

Set password for your wireless network if you use the product with a wireless router. Being not protected with password or using the default wireless router password may expose your video data to potential threat.

Please change your password every three months to safely protect personal information and to prevent the damage of the information theft.

Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.

overview

Important Safety Instructions

Read these operating instructions carefully before using the unit.

Follow all the safety instructions listed below.

Keep these operating instructions handy for future reference.

1)Read these instructions.

2)Keep these instructions.

3)Heed all warnings.

4)Follow all instructions.

5)Do not use this apparatus near water.

6)Clean only with dry cloth.

7)Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8)Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9)Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10)Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11)Only use attachments/accessories specified by the manufacturer.

12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13)Unplug this apparatus during lightning storms or when unused for long periods of time.

14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

overview!

English _3

overview

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.

This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

•To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

•To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.

WARNING

1. Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product.

2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to the product.

3. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.

4. When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury.

5. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.

6. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.

7. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.

8. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.)

9. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.

10. Do not expose the product to the direct airflow from an air conditioner.

Otherwise, it may cause moisture condensation inside the Clear Dome due to temperature difference between internal and external of the dome camera.

11.If you install this product in a low-temp area such as inside a cold store, you must seal up the wiring pipe with silicon, so that the external air can not flow inside the housing.

Otherwise, external high, humid air may flow inside the housing, pooling moisture or vapor inside the product due to a difference between internal and external temperature.

4_ overview

CALIFORNIA USA ONLY

This Perchlorate warning applies only to primary CR (Manganese Dioxide) Lithium coin cells in the product sold or distributed ONLY in California USA. “Perchlorate Material - special handling may apply, See www.dtsc.ca.gov/ hazardouswaste/perchlorate.”

Before Start

This user manual provides Information for using the DVR such as brief introduction, part names, functions, connection to other equipment, menu setup, etc.

You have to keep in mind the following notices :

• SAMSUNG retains the copyright on this manual.

• This manual cannot be copied without SAMSUNG’s prior written approval.

• We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of instructions mentioned in this manual.

• Prior to opening the case, please consult a qualified technician first. Whenever this is needed power must be removed from the unit.

• Before installing an additional HDD or connecting an external storage device (USB HDD) to this DVR, check the compatibility. Consult your provider for the compatibility list.

Warning

Battery

It is essential that when changing the battery in the unit, the replacement battery must be of the same type otherwise there may be a possibility of an explosion.

The following are the specifications of the battery you are using now.

• Normal voltage : 3V

• Normal capacity : 170mAh

• Continuous standard load : 0.2mA

• Operating temperature : -20°C ~ +85°C (-4°F ~ +185°F)

Caution

•Connect the power cord into a grounded outlet.

•The Mains plug is used as a disconnect device and shall stay readily operable at any time.

•Batteries shall not be exposed to excessive heat such as sunshine, fire or the like

•Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the Instructions.

System Shutdown

Turning off the power while the product is in operation, or undertaking improper actions may cause damage or malfunction to the hard drive or the product.

Please turn off the power, please right-click to display the context sensitive menu and select <Shutdown>. After selecting <OK> in the pop-up menu, you can pull off the power cord.

You may want to install a UPS system for safe operation in order to prevent damage caused by an unexpected power stoppage. (Any questions concerning UPS, consult your UPS retailer.)

Operating Temperature

The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F).

This product may not work properly if you run right after a long period of storage at a temperature below the guaranteed one.

Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand at room temperature for a period.

Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F). Likewise, the hard drive may not work at a temperature below the guaranteed one.

Ethernet Port

DVR is designed for indoor use only and all the communication wirings are limited to inside of the building.

overview!

English _5

overview

Contents

overview	5	Before Start
3	3	Important Safety Instructions
	6	Contents
	8	Features
	10	Part Names and Functions (Front)
	11	Part Names and Functions (Rear)
	12	Remote Control
connecting with other device	14	Checking the Installation Environment
14	14	installation
	15	Connecting External Devices
	15	Connecting the USB
	15	Connecting External SATA HDD
	16	Connecting the Camera (SDC-8440BC)
	18	Connecting the RS-485 Device
	18	Connecting the Network
live	20	Getting Started
	22	Live Screen Configuration
20	27	Live Mode
	30	Zoom
	30	Audio On/Off
	30	Freeze
	31	Event Monitoring
main menu	44	Setting the Device
32	32	System Setup
	53	Setting the Recording
	56	Setting the Event
	58	Backup
	60	Network Configuration
	73	Controlling a PTZ Device

6_ overview

search & play	76	Search
76	79	Playback
Web Viewer	81	Introducing Web Viewer
	82	Connecting Web Viewer (Windows)
81	84	Using Live Viewer (Windows)
	89	Controlling a Connected PTZ Camera
	92	Using Search Viewer
	95	Viewer Setup
	106	About
	107	Connecting Web Viewer (Mac)
	109	Using Live Viewer (Mac)
	110	Mobile Viewer
backup viewer	111	SEC Backup Viewer
111
appendix	114	Product Specification(DVR)
113	113	Product Specification (Camera)
	117	Product Overview
	119	Default Setting
	122	Troubleshooting
	125	Open Source License Report on the Product

overview!

English _7

overview

Features

The DVR employs H.264 video encoding for 4/16 channel inputs and G.711 audio encoding for 4/16 channels while simultaneously supports hard disc recording and playback.

These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video and audio data.

•Provides a convenient User Interface

•4/16 CH Composite Input Connectors

•Supports 720p/WD1/4CIF/2CIF/CIF recording formats

•With the network specific codec, network transfer enabled regardless of the recording conditions

•De-interlacing processor for better picture quality

•Display of HDD information and status by using HDD SMART

•Hard Disk overwrite function

•Mass storage hard disk backup through high-speed USB 2.0

•Simultaneous Record and Playback of 16-channel video data

•Various Search Modes (Search by Time, Event, Backup and Motion Detection)

•Various Recording Modes (Manual, Event, Scheduled Recording)

•Remote Monitoring function by Network Viewer, Smart Viewer and Mobile Viewer

Standards Approvals

MM`` This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

8_ overview

package Contents

Please unwrap the product, and place the product on a flat place or in the place to be installed. Please check the following contents are included in addition to the main unit.

M	`	The appearance of the components may differ from the image shown.
	`	Accessory category and quantity may differ depending on sales region.

REC NETWORK POWER

DVR (1SET)

Adapter / Power Cable(1EA)

Mouse (1EA)

Remote Control (1EA) / Battery (2EA)

SDC-8440BC *

Camera Cable * ( 60FT or 90FT)

	Camera Power Cable*	Network Cable(1EA) / HDMI Cable (1EA)	Quick Start Guide(1EA)
	(4 splitter, 5 splitter or 8 splitter)

Expansion pipe and Screw *		Network Viewer Software /User Manual CD (1EA)
Model	SDC-8440BC	Adapter/Power cable	Camera Cable	Expansion pipe and	Camera Power
				Screw	cable
SDH-C5100	10EA	1EA	60FT: 8EA	30EA/30EA	4 splitter 1EA
			90FT: 2EA		8 splitter 1EA
SDH-B3040	4EA	1EA	60FT: 4EA	12EA/12EA	5 splitter 1EA
SDH-B3020	2EA	1EA	60FT: 2EA	6EA/6EA	5 splitter 1EA

overvIeW!

English _9

overview

pArT nAmeS And funCTIonS (fronT)

SdrC5300

SdrB3300

a

REC NETWORK POWER

c b

	Part Names	Functions
	LED Indicator	REC : Lights on when recording is in progress.
a		NETWORK : Displays both network connection and data transfer status.
		POWER : Displays the power ON/OFF status.
b	USB Port	Connects the USB devices.
c	ReceiverRemote Control	Input the remote control signal.

M ` All functions are operable with mouse control, since there are no front buttons.

10_ overview

Part Names and Functions (Rear)

SDRC5300

a

overview!

eSATA

b c

d

e

CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

VGA

CH1

CH2

POWER

CH9

CH10

CH11

CH12

CH13

CH14

CH15

CH16

CH3

CH4

AUDIO OUT

HDMI

LAN

RS485

USB

DC 12 V

VIDEO IN

AUDIO IN

k j ih g f

SDRB3300

c	a b	d e
CH1	CH2	VGA	eSATA
	CH1 CH2		POWER

CH3	CH4	CH3	CH4		HDMI	LAN	RS485	USB	DC 12 V
	VIDEO IN	AUDIO IN		AUDIO OUT

k j i h g f

	Part Names	Functions
a	VIDEO IN	Input port for the composite video signal.
b	AUDIO IN	Input ports (RCA jack) for the audio signal.

An anti-theft lock allows you to use the product securely even in public places.

c Anti-theft Lock The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details.

d	VGA OUT	Output port for VGA video signal.
e	e-SATA	Ports used for external storage device connections.
f	DC 12V	DVR power input port.
g	USB	USB connector port.
h	RS-485	Used to establish RS-485 communications.
i	LAN	NETWORK connector port.
j	HDMI	HDMI connector port.
k	AUDIO OUT	Output port (RCA jack) for the audio signal.

English _11

overview

Remote Control

	POWER	REC
	Displays the Exit pop up screen.	Starts or ends the live recording.
	NUMBER [0~+10]
	Used as the numeric input keys, or displays a single
	channel.	ID
	PTZ	Sets the ID of the system.
		Select 2 digits from 0 ~ 9 while pressing the ID Key.
	Displays or ends PTZ.	SCROLL ,.
	T/W
	Zooms in or out.	Moves the menu scroll.
	SEARCH	VIEW
		Runs the View function in the PTZ mode.
	Displays the search menu.
	MODE	BACKUP
	Changes the screen mode.	Displays the Backup Menu.
	MENU	RETURN
	Goes to the system menu screen.	Returns to the previous screen.
		Up/Down/Left/Right($%_ +)/ENTER
	PRESET	Moves the cursor up/down/left/right, and runs the
		Select Menu.
	Displays the Preset Setup.	REC LOCK
	FREEZE	Selects the recording lock function.
	Freezes the screen temporarily.	AUDIO
	ZOOM	Turns Audio on/off.
	Runs the digital zoom (x2) function.	ALARM
	Skip Backward (by unit time),	Cancels the Alarm.
		Move Frame
	Slow Rewind, Slow Forward,
	Skip Forward (by unit time)	While paused, moves to the previous/next frame.

FR, STOP, PLAY/PAUSE, FF

Using the numeric buttons

CHANNEL 1–9	Press each button between 1 to 9. (8CH : 8)
CHANNEL 10	Press the [0/+10] button first, then press the [0/+10] within 1 second.
CHANNEL 11–16	Press the [0/+10] button first, then press any number between 1 to 6.

12_ overview

Changing the Remote Control ID

1.Press the [ID] button of the remote control and check the ID displayed on the DVR screen. The factory default ID of the remote control is 00.

2.Enter 2 digits of your selection in order, while pressing the system [ID] button.

3.When ID input is done, press the system [ID] button again to check the setting.

MM`` If you want to change the remote control ID to 08: Press 0 and 8 in order while the system [ID] button is pressed. Remote control's ID and DVR’s ID should be matched for proper operation. Refer to “Remote Devices”. (Page 50)

overview!

English _13

connecting with other device

InSTALLATIon

Please take note of the followings before using this product.

•Do not use the product outdoor.

•Do not spill water or liquid in the connection part of the product.

•Do not impose the system to excessive shock or force.

•Do not pull out the power plug forcefully.

•Do not disassemble the product on your own.

•Do not exceed the rated input/output range.

•Use a certified power cord only.

•For the product with an input ground, use a grounded power plug.

CheCKInG The InSTALLATIon envIronmenT

Samsung Digital Video Recorder (“DVR” hereinafter) is a state-	Temperature
of-art security device, and contains mass storage hard disk(s)	Unit: ºC
and critical circuits inside.
When the temperature rises inside the product, the product may
breakdown and the product life be shortened. Please pay
attention to the following recommendations before installation.

One Year: 24HR X 365 DAY =8,760 HR

	[Figure 1]
		Life (Unit: HOURS)
The followings are the recommendations when Samsung DVR is installed on a rack.		[Figure 1]
1.	Please ensure that the rack inside is not sealed.
2.	Please ensure the air is circulated through the inlet/outlet as shown in the picture.
3.	If the DVR or other devices on a rack is to be stacked as in the picture, provide a
4.	suitable space or install a ventilating opening for air circulation.
	For natural air convection, place the inlet at the bottom of the rack and the outlet on top.
5.	It is strongly recommended that a fan motor is installed at the inlet and the outlet for air
6.	circulation. (Please fit a filter at the inlet to screen dust or foreign substances.)
	Please maintain the temperature inside the rack or surrounding areas between
	0°C ~ 40°C (32°F ~ 104°F) as shown in the figure 1.
Rack Mount Instructions - The following or similar rack-mount instructions are
included with the installation instructions :
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the
	operating ambient temperature of the rack environment may be greater than room
	ambient. Therefore, consideration should be given to installing the equipment in an
	environment compatible with the maximum ambient temperature specified by the
	manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such that the		[[Fiigure 2]
	amount of air flow required for safe operation of the equipment is not compromised.
C) Mechanical Loading - Mounting of the equipment in the rack should be such that a
	hazardous condition is not achieved due to uneven mechanical loading.
D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply
	circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring.
E)	Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
	Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should
	be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

14_ connecting with other device

ConneCTInG exTernAL devICeS

` The following figures are based on Model SDR-C5300.

VIDEO IN	CH1	CH2			VGA
					eSATA
	CH3
	AUDIO IN		AUDIO		POWER
			OUT	HDMI
					LAN

USB

12 V

devICe oTher WITh ConneCTInG!

ConneCTInG The uSB

1.By factory default, a USB port is provided for external connection.

2.You can connect a USB HDD, USB memory or mouse to the USB port.

3.If a USB HDD is connected to the system, recognition and settings are available in “main menu > Setting the device > Storage device”. (Page 47)

4.This product supports hot-plugging, which connects/removes the USB device during the system operation.

J ` If you use the USB device for Backup purposes, format it with FAT32 on PC if it is not formatted on the DVR.

ConneCTInG exTernAL SATA hdd (eSATA)

External SATA port is provided on the rear panel.
If connected to the system, the external SATA HDD (eSATA) can be recognized and configured in “main menu >
device		> Storage device”.
J	`	Use a cable shorter than 1 m for the external external SATA HDD (eSATA) connections.
	`	Unexpected disconnection to a device in use which is connected via eSATA may restart the system. Check whether the
		device is in use before disconnecting it.

` In the event of replacing an HDD of an external SATA HDD, please power off the external SATA HDD to change the HDD.

English _15

connecting with other device

ConneCTInG The CAmerA (SdC-8440BC)

Equipped with the IR LED and the illumination sensor, enables you to monitor at night as well as in daytime. The camera is suitable for both internal and external use.

`Please make sure not to fully expose the camera to rain. The camera must be installed under a shelter to avoid exposure to excessive rain or moisture.

a

b

c

d e

	Name	Description
a	IR LED	These infrared LED's are controlled by the illumination sensor.
b	Lens	Focal length of 3.6mm enables you to cover relatively longer range of monitoring.
c	Illumination Sensor	Detects incoming light to control the IR LED.
d	BNC Cable	BNC terminal for video signal output.
e	Power Cable	Used to plug the power cable.

16_ connecting with other device

Connecting with dvr

` The following figures are based on Model SDR-C5300.

VIDEO IN	CH1	CH2			VGA
							eSATA
	CH3	CH4
	AUDIO IN		AUDIO					POWER
			OUT	HDMI	LAN
						RS485
							USB
								DC 12 V

Installing the camera

The camera can be installed on the wall, ceiling, shelf or a desired position using the provided bracket.

devICe oTher WITh ConneCTInG!

wall or ceiling

1.Choose an installation site that can sufficiently support the weight of the equipments to be installed.

2.Attach the camera bracket to the wall using the supplied screws.

3.Adjust the direction of the camera to the desired direction, and fix bracket.

4.Fix the camera.

5.Connect the camera cable to the camera.

J `	You should be careful when installing the camera outdoors because the cable connectors may be wet with moisture or pile
	up with impurities.
`	The camera satisfies the IP66 standard, and direct exposure to water or moisture may cause problem such as
	condensation.

English _17

connecting with other device

ConneCTInG The rS-485 devICe

Connect the rear [rS-485 +, –] port to the PTZ camera.

J	`	You can connect and control the PTZ camera which supports the RS-485 communication.
	`	Check if the RS-485 device is compatible with the product first.
				RS485
	` Pay attention not to change the polarity (+/-) of the RS-485 device when connecting it.
	`	Depending on camera’s type, connection polarity can be different. For further information,
		refer to the respective PTZ Camera’s documentation.

ConneCTInG The neTWorK

` The following figures are based on Model SDR-C5300.

Connecting to network through ethernet (10/100BaseT)

Hub/Switcher

Windows

Network Viewer

RJ-45 Ethernet Cable

(Direct Cable)

Back Bone

Hub/Switcher

NETWORK

18_ connecting with other device

Connecting to the Network using the router

Broadband Router

xDSL or Cable Modem

xDSL or Cable Modem

External
Remote PC	NETWORK

DDNS Server

(Data Center)

Connecting to Network through ADSL

RJ-45 Ethernet Cable

(Direct Cable)

ADSL MODEM	Phone(ADSL) Line	NETWORK
Windows	Hub/Switcher
Network Viewer

device other with connecting!

English _19

live

GeTTInG STArTed

Starting the system

1. Connect the power cable of the DVR to the wall outlet.

M ` Itbooting.takes about 10 seconds to display the start screen after

2.You will see the initialization screen.

The initialization process will last about 1 minute.

If a new HDD is installed, the initialization process may take longer.

REC

3. The live screen appears with a beep.

2014-01-01 01:10:25

2014-01-01 01:10:25

Shutting down the System

You can shut down the system only if you have logged in to the DVR.

You require permission to shut down the system if you are not logged in as admin.

1.	Press the [poWer] button on the remote control, or	2014-01-01 01:10:25
	right-click to display the context sensitive menu and select
2.	<Shutdown>.
	The “Shutdown” confirmation window appears.	Shutdown
3.	Use the arrow keys on the remote control to move to	Are you sure to shutdown?
		OK Cancel
	<oK> and press the [enTer] button or click <oK>. The
	system will shut down.

		For the permission management, refer to “Permission	2014-01-01
M	`		01:10:25
		Management > Setting Permissions”. (Page 39)

20_ live

Login

To access a DVR or restricted menu, you should have logged in to the DVR.
1. In live mode, right-click any area of the screen.	2014-01-01 01:10:25
You will see the context sensitive menu as in the right	Audio Off
figure.	Scene Mode 
	Freeze
	Stop Alarm
	Record
	Play
	Search
	Backup
	Main Menu
	Shutdown
	Hide Launcher
	Login

2.Click <Login>.

The login dialog appears.

You can also see the login dialog to access a desired menu by pressing the [menu] button on the remote control.

`The login dialog will also appear if you press a menu button on the remote control when the corresponding menu requires logging in.

`After logged in, press [RETURN] on the remote control to display the logout dialog.

Login

 ID

admin

 Password

OK Cancel

J	`	The initial administrator ID is “admin” and the password should be set when logging in for the first time.
	`	Set password for your wireless network if you use the product with a wireless router. Being not protected with password or
		using the default wireless router password may expose your video data to potential threat.
	`	Please change your password every three months to safely protect personal information and to prevent the damage of the
		information theft.
		Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a
		password.
M `		For the restricted permission, refer to “Permission Management > Setting Permissions”. (Page 39)

Locking All Buttons

This will restrict access to all buttons available in the DVR.

1.In Live mode, press buttons on the remote control in the order of [STop (@)][freeZe][STop (@)][freeZe] [menu].

All buttons will be locked.

2.In the lock condition, press any button to display a dialog where you are prompted to enter the password for unlocking the buttons.

The button lock will be released if you enter the admin password.

2014-01-01 01:10:25

Key Lock Password

 ID

admin

 Password

OK Cancel

LIve!

English _21

live

Live Screen Configuration

Icons on the Live Screen

You can check the status or operation of the DVR with the icons on the live screen.

			a	d b
	d		2014-01-01 00:00:01	c
	e
	f	CAM 01
	g
		Name		Description
a	Current Date, Time		Displays the current time and date.
b	Login Information		When you are logged in, the “LOG ON” icon will be displayed.
			Displayed if the zoom function is activated.
			Freezes the screen temporarily.
c	Screen Mode		Displayed in Auto Sequence mode where all channels are switched at the specific
			time interval.
			This icon is displayed if a user with restricted access to the Record button tries to
			make manual recording.
			`` Only the user with the applicable permission can release (stop) the recording.
			Displayed if the HDD is full and the DVR has an insufficient space to record.
			Displayed if no HDD is installed or the existing HDD should be replaced.
			Displayed if the HDD needs a technical examination.
d System Operation			Displayed when the Wi-Fi is connected.

Displayed when the Wi-Fi is not connected.

Displayed if a new firmware is found from the network.

This will be displayed if the backup operation is in process.

	e	Video Input Status	Displayed if no input is entered in the condition that the camera is set to <ON>.
			Nothing will be displayed on the screen if the camera is set to <OFF>.

22_ live

	Name		Description
f	Camera Name/ Channel		Displays the camera name and the changed channel, if any.
			Displayed in PTZ setting, and highlighted yellow if PTZ is in operation.
			Displays AUDIO ON/MUTE.
			Not displayed in video mode if deactivated.
g	Camera Operation		Displayed if a motion detected in the condition that the motion detection is set to
			<ON>.
			Appears when the Tampering Detection is set to <ON> and a tampering attempt is
			detected.
			Displays the current record mode from Record/Event/Schedule.

error Information

•If the internal HDD is not connected, the “NO HDD”( ) message will appear; if there occurs a problem, you will see the “HDD FAIL”( ) message in the top left corner. In this case, make sure you contact the service center for assistance as this may cause a failure of recording, playback or backup.

M ` If you see NO HDD, HDD FAIL icons on the screen, contact the service center for more details.

Live Screen menu

In addition to the buttons on the remote control, you can access a desired menu by right-clicking the mouse any area in live mode.

The context sensitive menu that appears by right-clicking the screen may differ, depending on the login/ logout, screen split mode and DVR operation mode.

M ` Menu items of Search, Record, Backup and Shutdown can be deactivated, depending on the user permission.

2014-01-01 01:10:25	2014-01-01 01:10:25
Scene Mode 	Scene Mode 
Audio Off	PTZ Control
Freeze	Zoom In
Stop Alarm	Audio off
Record	Freeze
Play	Stop Alarm
Search	Record
Backup	Play
Main Menu	Search
Shutdown	Backup
Hide Launcher	Main Menu
Logout	Shutdown
	Hide Launcher
	Logout

< Split Mode Menu > < Single Mode Menu >

LIve!

English _23

live

Split mode menu

The context sensitive menu in split mode differs, depending on the login/logout status.

										2014-01-01 01:10:25
								b	a	Scene Mode 
										Audio Off
							c
										Freeze
						d
										Stop Alarm
					e
										Record
				f
										Play
			hg
										Search
		ji								Backup
										Main Menu
	k									Shutdown
l										Hide Launcher
										Logout
		Menu								Description
a Scene Mode					Refer to “Live Mode”. (Page27)
b Audio On/Off					Refer to “Audio On/Off”. (Page 30)
c Freeze					Refer to “Freeze”. (Page 30)
d Stop Alarm					Stops the alarm output and the event monitoring. Refer to “Event Monitoring”.(Page 31)
e Record/Stop					Starts/stops the standard recording.
f Play					Plays the search result (data). Refer to “Search & Play > Play”. (Page 79)
g Search					Refer to “Search & Play > Search”. (Page 76)
h Backup					Refer to “Main Menu > Setting the Backup”. (Page 58)
i Main Menu					Accesses the main menu. Refer to the Using the DVR section. (Page 32)
j Shutdown					Turns down the DVR.
k Show/Hide Launcher					Shows or hides the launcher. Refer to “View the Launcher Menu”. (Page 26)
l Login/Logout					You can log in or out.

24_ live

Single mode menu

The single mode menu is available only in Single Mode.

The context sensitive menu for the One Channel mode, in Split mode is different from that of the Single mode.

		2014-01-01 01:10:25
a	Full Screen
b	PTZ Control
	Zoom In
	Audio On
	Freeze
	Stop Alarm
	Record
	Play
	Search
	Backup
	Main Menu
	Shutdown
	Hide Launcher
	Logout	Alarm	Freeze

	Menu	Description
a	Full Screen	Select and click a desired channel in Split mode to switch to the full screen of the selected channel.
b	Zoom In	Enlarges the selected image. (Page 30)

LIve!

English _25

live

view the Launcher menu

The Launcher menu appears on the bottom of the live screen.

1.In Live mode, right-click to display the context menu and select <Show Launcher>.

2.Move the cursor to the bottom and click a desired item in the Launcher menu.

M ` If no input is entered for 10 seconds, the menu will disappear.

`The Launcher menu can be accessed only by using the mouse.

`SDR-B3300 supports the 4-split screen mode PIP and Auto Sequence only.

2014-01-01 01:10:25

2014-01-01 01:10:25

2014-01-01 01:10:25

2014-01-01

01:10:25

		a		b	cd e f g h ij
			Menu		Description
	a	Date/Time		Displays the current time and date.		>
				The indication of AM/PM is displayed if you set 12 hours for the time format in “
					System
				Date/Time/Language > Time”. (Page 32)
	b	Screen Mode		Press this button to switch the screen mode in sequence.
				The current mode is highlighted in white.
	c	Menu Expansion Button		Click to display the hidden menu to the right.
	d	Audio		Turns ON/OFF the sound of the selected channel.
	e	Zoom		Enlarges the selected area. This is available only in Single Live mode.
	f	PTZ		Runs the PTZ Control launcher.
				The PTZ control launcher will be active on the Live screen after you select a single channel.
	g	Alarm		Stops the alarm if it's activated.
	h	Freeze		Freezes the Live screen temporarily.
	i	Play		Enters Play mode if a file to play exist, and if not, enters Search mode.
	j	Record		Start/End recording the Live screen.

26_ live

Live Mode

SDR-C5300 display Live images from 16 channels in a total of 8 layout of split screens.

Switching the screen mode

To switch the split mode, select a screen mode in the launcher menu, or right-click to select a screen mode in the context menu.

Press the [MODE] button on the remote control to switch the mode in the sequence of the launcher menu items.

MM`` SDR-B3300 supports the 4-split screen mode PIP and Auto Sequence only.

CH1

CH2

CH3

CH4

CH1

CH2

CH3

CH2

CH5

CH6

CH7

CH8

CH1

CH2

CH9

CH10

CH11

CH12

CH4

CH5

CH6

CH1

CH3

CH13

CH14

CH15

CH16

CH7

CH8

CH9

CH3

CH4

CH4

CH5

CH6

CH7

16-split mode

9-split mode

4-split mode

7-split mode

CH2

CH3

CH4

CH5

CH1

CH2

CH3

CH6

CH7

CH8

CH1

CH19

CH4

CH5

CH6

CH10

CH11

CH12

CH13

CH14

CH15

CH16

CH1

CH2

CH1

CH10

CH11

CH12

CH13

CH7

CH8

CH9

13-split mode

16(A)-split mode

PIP

Auto Sequence

Switching the split mode

SDR-C5300 display 16 Live images in the sequence of Single, 4-split and 9-split modes.

Auto Sequence

live!

	16		13-16		CH1	CH2	CH3
	CH1	CH2		CH1	CH2	CH3
			9-12	CH4	CH5	CH6
			1-45-8				1-9
CH1	CH3	CH4		CH7	CH8	CH9	10-16
Single mode 1	4-split mode				9-split mode

English _27

live

MM`` In Single mode, If you have set <SEQ-Dwell Time> in “Setting the Device > Camera”, Auto Sequence will be conducted at the set interval. (Page 44)

`` In a split mode, If you have set <Multi CH SEQ Time> in “Setting the Device > Monitor”, Auto Sequence will be conducted at the set interval. (Page 51)

Manual Switching

Press the left/right button on the remote control, or click the arrow <_/+> key to move to the next split mode.

•If pressing the right [+] button in 9-split mode :

9-split (CH 1~9) mode  9-split (CH 10~16) mode  Auto Sequence

CH1

CH2

CH3

;

CH10

CH11

CH12

;

CH1

CH2

CH3

CH4

CH5

CH6

CH13

CH14

CH15

CH4

CH5

CH6

CH7

CH8

CH9

CH16

CH7

CH8

CH9

10-16

1-9

•If pressing the right [+] button in 4-split mode :

Channel (CH 1~4)  Channel (CH 5~8)  Channel (CH 9~12)  Channel (CH 13~16)  Auto Sequence

CH1	CH2	;	CH5	CH6	;	CH9	CH10	;	CH13		CH14
CH3	CH4		CH7	CH8		CH11	CH12		CH15		CH16
										;

CH1	CH2
CH3	CH4

13-16

9-12

1-45-8

28_ live

Channel Setting

You can display the channel in a desired area of a split screen.

1.

Place the cursor over the camera name of each channel to display the <%> key to the right on the screen.

live!

2.

Click a camera name to display a channel list where you can select a different channel.

3.

Select a desired channel and click it.

The current channel will be switched to the selected one.

Use the cursor to select a channel to move, and drag and drop it to a desired channel; this can also

change the channel position.

` Ex : if switching CH 1 to CH 7

CH1

CH2

CH3

CH4

CH7

CH2

CH3

CH4

CH5

CH6

CH7

CH8

;

CH5

CH6

CH1

CH8

CH9

CH10

CH11

CH12

CH9

CH10

CH11

CH12

CH13

CH14

CH15

CH16

CH13

CH14

CH15

CH16

Switching to Single Mode

When in split mode, select and double-click a desired channel to switch to its Single mode.

Press the number corresponding to a desired channel on the remote control to switch to its Single mode.

•CHANNEL 1–9 : Press each button between 1 to 9. (8CH : 8)

•CHANNEL 10 : Press the [0/+10] button.

•CHANNEL 11–16 : Press the [0/+10] button first, then press any number between 1 to 6 within 1 second. Refer to “Remote Control > Using the numeric buttons”. (Page 12)

`` Ex : If double-clicking CH 3 or pressing the number “3” on the remote control.

	CH1	CH2	CH3	CH4
	CH5	CH6	CH7	CH8	;
	CH9	CH10	CH11	CH12
	CH13	CH14	CH15	CH16		CH3

English _29

live

Zoom
This is available only in Single Live mode. In Single mode, select a desired area and use the Zoom function to
enlarge it twice.
1. Select <Zoom In> in the right-click menu.	> in the launcher menu. The zoom
Press the [Zoom] button on the remote control, or simply click <
box appears.

2.Use the direction keys, or drag and drop to specify an area to enlarge.

3.Press the [enTer] button, or double-click the selected area to enlarge it twice.

`In the enlarged image, use the direction buttons ($%_ +) on the remote control to move the enlarged area.

4. Press the [Zoom] button on the remote control, or simply click <	> in the launcher menu to release
the zoom.
2014-01-01 01:10:25	2014-01-01 01:10:25

;

AudIo on/off

You can turn the sound on/off corresponding to the channel in Live mode.

AudIo on/off in Single mode

Click the audio icon ( ) on the screen, or press the [AudIo] button on the remote control to turn it on/off.

M ` Only the channel where <Audio> is set to <ON> in “Device > Camera” displays the audio icon ( ) in Live mode that you can use to turn the sound on/off.

freeZe

This is available only in Live mode, this pauses playing the Live image temporarily.

1.	Press the [freeZe] button on the remote control, or click <		> in the launcher menu.
2.	The playback of the image is stopped temporarily.
	Press the [freeZe] button again, or click <	>.
	This will release the freeze.

30_ live