Samsung NP200A5BA03US, 460DR-2, TC190-2-4, SUR40 User Manual

0 (0)

SyncMaster 460DR-2

LCD Display

User Manual

The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.

Safety Instructions

Notational

Note

These safety instructions must be followed to ensure your safety and prevent property damage.

Make sure to read the instructions carefully and use the product in the correct manner.

Warning / Caution

Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.

Note

Prohibited

Do not disassemble

Do not touch

Important to read and understand at all times

Disconnect the plug from the outlet

Ground to prevent an electric shock

An administration fee may be charged if either

•(a) an engineer is called out at your request and there is no defect in the product

(i.e. where you have failed to read this user manual).

•(b) you bring the unit to a repair centre and there is no defect in the product (i.e. where you have failed to read this user manual).

The amount of such administration charge will be advised to you before any work or home visit is carried out.

Cleaning the Monitor

Cleaning

The panel and exterior of the cutting-edge monitor scratch easily and require careful attention. Clean the monitor according to the following steps.

•Power off the monitor and PC.

•Disconnect the power cable from the monitor.

Note

To avoid electric shock, be sure you disconnect the cable by gripping the plug and do not touch the cable with wet hands.

Safety Instructions

•Wipe the monitor using a soft, slightly damp cloth that has been squeezed .

Do not use a cleaning agent that contains alcohol or solvents, or that is surface active.

Otherwise, the exterior may discolor or crack or the panel coating may come off.

Do not spray water or cleaning agent directly onto the monitor.

Otherwise, the liquid may sink into the monitor and cause a fire, electric shock, or failure.

•Clean the exterior of the monitor using a soft cloth dampened with a small amount of water.

•Connect the power cable to the monitor after you have finished cleaning.

•Power on the monitor and PC.

Power

When not used for extended period of time, set your computer to DPM.

If using a screen saver, set it to active screen mode.

The images here are for reference only, and are not applicable in all cases (or countries).

Shortcut to Anti-Afterimage Instructions

Do not use a damaged power cord or plug or a damaged or loose power outlet.

•Otherwise, this may result in electric shock or fire.

Do not touch the power plug with wet hands when removing or plugging the plug into the outlet.

•Otherwise, this may result in electric shock.

Make sure to connect the power cord to a grounded power outlet.

•Otherwise, it may result in electric shock or personal injury.

Ensure that the power plug is plugged into the power outlet firmly and correctly.

•Otherwise, this may result in fire.

Safety Instructions

Do not forcefully bend or pull the power plug and do not place any heavy material on it.

•Otherwise, this may result in fire.

Do not connect multiple appliances to the same power outlet.

•Otherwise, this may cause fire due to overheating.

Do not disconnect the power cord while using the product.

•Otherwise, this may result in damage to the product due to electric shock.

To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

•Otherwise, this may cause electric shock or fire.

Use only the power cord provided by our company. Do not use the provided power cord of another product.

•Otherwise, this may result in fire or electric shock.

Connect the power plug to a wall outlet that can be easily reached.

•When a problem occurs with the product, you must unplug the power plug to cut the power off completely. You cannot cut the power off completely using only the power button on the product.

Installation

Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc.

Failure to do so may cause serious damage to your monitor.

Ensure that at least two persons lift and move the product.

•Otherwise, it may be dropped and cause personal injury, and/ or damage the product.

When installing the product in a cabinet or rack, make sure that the front end of the bottom of the product does not project out.

•Otherwise, it may fall or cause personal injury.

•Use a cabinet or rack of a size appropriate to the product.

DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGA-

RETTES AND ANY HEATING APPLIANCES NEAR THE PROD-

UCT.

Safety Instructions

•Otherwise, this may result in fire.

Keep heating appliances as far away from the power cord or the product as possible.

•Otherwise, this may result in electric shock or fire.

Do not install it in a badly ventilated location such as a bookcase or closet.

•Otherwise, this may result in fire due to an increase in the internal temperature.

When putting the product down, make sure to put it down softly.

•Otherwise, this may result in damage to the screen display.

Do not place the front of the product on the floor.

•Otherwise, this may result in damage to the screen display.

Ensure that an authorized installation company installs the wall mount.

•Otherwise, it may fall and cause personal injury.

•Make sure to install the specified wall mount.

Install your product in a well ventilated location. Ensure that there is a clearance of more than 4 inches (10 cm) from the wall.

•Otherwise, it may result in fire due to an increase in the internal temperature.

Ensure that the packaging vinyl is kept away from children.

•Otherwise, it may result in serious harm (suffocation) if children play with it.

If the height of your monitor is adjustable, do not place any object or part of your body on the stand when lowering it.

•This may cause damage to the product or the person carrying it.

Edible oil, such as soybean oil, can damage or deform the product. Do not install the product in a kitchen or near a kitchen counter.

Others

The product is a high voltage product. Do not disassemble, repair or modify the product yourself.

•Otherwise, this may result in electric shock or fire. If the product needs to be repaired, contact a Service Center.

Safety Instructions

If there is a strange smell or a strange sound or smoke is coming from the product, disconnect the power plug immediately and contact a Service Center.

•Otherwise, this may result in electric shock or fire.

Do not place this product in a location exposed to moisture, dust, smoke, water, or in a car.

•Otherwise, this may result in electric shock or fire.

When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center.

•Otherwise, this may result in electric shock or fire.

During a lightning or thunderstorm, power off the product and remove the power cable.

•Otherwise, this may result in electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal cable.

•Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.

Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables.

•Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.

Make sure that the ventilating opening is not blocked by a table or curtain.

•Otherwise, it may result in fire due to an increase in the internal temperature.

Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product.

•If water or a foreign material enters the product, disconnect the power cord and contact a Service Center.

•This may result in a product malfunction, electric shock, or fire.

Do not use or keep combustible spray or flammable material near the product.

•Otherwise, this may result in an explosion or fire.

Do not insert any metal, such as chopsticks, coins, pins and steel, or flammable objects, such as matches or paper, inside the product (through the ventilating openings, input and output terminals, etc).

•If water or foreign material enters the product, disconnect the power cord and contact a Service Center.

•Otherwise, this may result in electric shock or fire.

Safety Instructions

When using a fixed screen for a long time, an afterimage or stain may occur.

•If you are not using your product for a long period of time, put it into sleep mode or use a moving screen saver.

Set a resolution and frequency appropriate to the product.

•Otherwise, your eyesight may be damaged.

When using headphones or earphones, do not turn the volume too high.

•Having the sound too loud may damage your hearing.

To avoid eyestrain, do not sit too close to the product.

Take a rest for at least five (5) minutes after using the monitor for one (1) hour.

This reduces eye fatigue.

Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations.

•Otherwise, it may fall and cause personal injury and/or damage the product.

•If you use the product in a location exposed to vibrations, it may damage the product and result in fire.

When moving the product, turn the power off and disconnect the power plug, antenna cable, and all the cables connected to the product.

•Otherwise, it may result in electric shock or fire.

Ensure that children do not hang onto the product or climb up onto the product.

•The product may fall and cause personal injury or death.

If you do not use the product for a long period of time, disconnect the power cord from the power outlet.

•Otherwise, this may result in overheating or fire due to dust, and may result in fire due to electric shock or leakage.

Do not place any heavy items or toys or confectionery, such as cookies etc. that may attract the attention of children and to the product.

•Your children may hang onto the product causing it to fall and this may result in personal injury or death.

Safety Instructions

Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that children or infants cannot reach.

•If children have had the battery in their mouths, consult your doctor immediately.

When replacing the battery, insert it with the right polarity (+, -).

•Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid.

Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time.

•Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage of the internal liquid.

The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling.

•The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery.

Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater.

•This may reduce the lifetime of the product, and may result in fire.

Do not drop any objects onto the product or cause any impact to the product.

•Otherwise, this may result in electric shock or fire.

Do not use a humidifier near the product.

•Otherwise, this may result in electric shock or fire.

When there is a gas leak, do not touch the product or the power plug; ventilate immediately.

•If a spark occurs, it may cause an explosion or fire.

If the product has been turned on for a long time, the display panel becomes hot. Do not touch it.

Keep the small accessories in a location out of the reach of children.

Safety Instructions

Be careful when adjusting the angle of the product or the height of the stand.

•This may result in personal injury as your hand or fingers may become caught.

•Also, if you tilt the product too far, it may fall and cause personal injury.

Do not install the product in a location low enough for children to reach.

•Otherwise, it may fall and result in personal injury.

•Since the front part of the product is heavy, install the product on a level and stable surface.

Do not put any heavy objects on the product.

•This may result in personal injury and/or damage to the product.

Introduction

Package Contents

Checking the Contents of the Package

Remove the lock from the package box, as shown in the figure above.

Lift up the package box by	Check the contents of the	Remove the styrofoam
holding the grooves on	package.	and vinyl cover.
both sides of the package
box.

Note

•After unpacking the package, make sure to check the contents of the package.

•Store the packaging box in case you need to move the product later.

•If any items are missing, contact your dealer.

•Contact a local dealer to purchase optional items.

•This image is for reference only.

Unpacking

Introduction

LCD Display

Manuals

Quick Setup Guide	Warranty Card	User Manual
	(Not available in some lo-
	cations)

Cables

Power Cord

Others

Remote Control	Batteries (AAA X 2)
	(Not available in some lo-
	cations)
Sold separately

Wall Mount KIT

RCA-Stereo Cable

HDMI-DVI Cable

D-Sub Cable

RGB to Component Cable

DP Cable

HDMI Cable	Stereo Cable	AV Cable

Introduction

Sold separately

DVI Cable

RS232C Cable

RCA Cable

Network box

Note

Accessories that can be purchased with the product vary by country.

Your LCD Display

Control Panel

MENU button [MENU]

Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu.

Navigate buttons (Up-Down buttons)

Moves from one menu item to another vertically or adjusts selected menu values.

Adjust buttons (Left-Right buttons) / Volume buttons

Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, press the button to adjust volume.

ENTER button [ENTER]

Introduction

Activates a highlighted menu item.

SOURCE button [SOURCE]

Switches from PC mode to Video mode. Selects the input source that an external device is connected to.

[PC] → [DVI] → [AV] → [Component] → [HDMI1] → [HDMI2] → [DisplayPort]

D.MENU button

Not available

Power button []

Use this button for turning the LCD Display on and off.

Brightness Sensor (Optional)

Automatically detects the surrounding brightness it accordingly.

Note

This function is activated only on the models equipped with an auto brightness sensor.

Power indicator

Shows PowerSaver mode by blinking green

Note

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your LCD Display OFF when it is not needed or when leaving it unattended for long periods.

Remote Control Sensor

Aim the remote control towards this spot on the LCD Display.

Rear

Note

See the "Connections" section for details about cable connections. The LCD Display's configuration at the back may vary slightly depending on the model.

Introduction

POWER ON / OFF

Switches the LCD Display On/Off.

POWER

The power cord plugs into the LCD Display and the wall outlet.

RGB/COMPONENT IN (PC/COMPO-

NENT Connection Terminal (Input))

•Connect the [RGB/COMPONENT IN] port on the monitor to the RGB port on the PC using the D-SUB cable.

•Connect the [RGB/COMPONENT IN] port on the monitor to the COMPONENT port on the external device using the RGB to COMPONENT cable.

•Connect the [RGB/COMPONENT IN] port on the monitor to the BNC port on the PC using the RGB to BNC cable.

DVI IN(PC Video Connection Terminal)

Connect the [DVI IN] port on the monitor to the DVI port on the PC using the DVI cable.

RGB/DVI/HDMI AUDIO IN (PC/DVI/ DP/HDMI Audio Connection Terminal (Input))

Connect the [RGB/DVI/DP/HDMI AUDIO IN] terminal of the monitor and the speaker output terminal of your computer's sound card using a stereo cable(sold separately).

DP IN

Receives a signal from the Displayport.

Connect the [DP IN] port on the LCD Display to the DP port on the PC using the DP cable.

AV/COMPONENT AUDIO IN [R-AUDIO-

Connect the [AV/COMPONENT AUDIO IN [R-AUDIO-L]] port on the monitor to the audio output port on the PC or on the external device using an audio cable.

AV IN

Introduction

Connect the [AV IN] terminal of your monitor to the video output terminal of the external device using a VIDEO cable.

AUDIO OUT

Connect a headphone or an External speaker.

HDMI IN 1

•Connect the [HDMI IN 1] terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI cable.

•Up to HDMI 1.3 can be supported.

Note

•A normal external device(DVD player or camcorder, etc.) can be connected to the [HDMI IN 1] terminal.

HDMI IN 2 (MAGICINFO)

•Connect the [HDMI IN 2 (MAGICINFO)] terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI cable.

•Up to HDMI 1.3 can be supported.

Note

To use MagicInfo, the network box specified separately by Samsung must be installed inside the product and the MagicInfo output of the network box must be connected to the [HDMI IN 2 (MAGICINFO)] terminal.

For more information on how to purchase and install a network box, contact Samsung Electronics.

RJ45 MDC (MDC PORT)

MDC(Multiple Display Control) Program Port

Connect the LAN cable to [RJ45 MDC] on the product and LAN on the PC. To use an MDC, the MDC program must be installed on the PC.

Introduction

Note

Go to Multi Control and select RJ45 MDC as the MDC Connection.

RS232C OUT/IN (RS232C Serial PORT)

MDC(Multiple Display Control) Program Port

Connect a serial cable (cross type) to [RS232C] on the product and RS232C on the PC. To use an MDC, the MDC program must be installed on the PC.

Note

Go to Multi Control and select RS232C

MDC as the MDC Connection.

Note

See the "Connections" section for details about cable connections.

Remote Control

Note

The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency.

Introduction

SOURCE

OFF

Number Buttons

+ VOL -

CONTENT (HOME)

MagicInfo Lite

SOURCE

OFF

Number Buttons

+ VOL -

CONTENT (HOME)

MagicInfo Lite

TOOLS

Up-Down Left-Right / Enter buttons

RETURN

The Color button / The PC/DVI/HDMI/DP selection button

MagicInfo 3D

() / / / () /

D.MENU

MUTE

BLANK

INFO

EXIT

LOCK

Power on the product.

Select a connected source device.

Power off the product.

Enter the password in the OSD menu.

Not available.

Adjust the volume.

Not available.

Introduction

TOOLS

Up-Down Left-Right / Enter buttons

Not available.

Up-Down Left-Right button : Move to the upper, lower, left or right menu, or adjust an option's setting.

Enter button : Activates a highlighted menu item.

RETURN

The Color button / The PC/DVI/HDMI/DP selection button

Return to the previous menu.

Manually select a connected input source from PC, DVI,

HDMI or DP.

MagicInfo

() / / / () /

D.MENU

MUTE

MagicInfo Quick Launch Button.

MagicInfo can only be enabled when a network box(sold separately)is connected.

This button is disabled for products that do not support

MagicInfo.

Not available.

Mute the sound.

Unmuting the sound: Press MUTE Press MUTE again or press the volume control (+ VOL -) button.

BLANK

INFO

EXIT

LOCK

Not available.

Display or hide the onscreen display menu, or return to the previous menu.

Not available.

Display information on the screen.

Exit the current menu.

It sets safe lock function.

Samsung NP200A5BA03US, 460DR-2, TC190-2-4, SUR40 User Manual

Introduction

Dimensions

Introduction

Installing a Wall Mount

Preparing before installing Wall-Mount

To install a wall-mount from another manufacturer, use the Holder-Ring.

Installing the Wall Mount Kit

The wall mount kit(sold separately) allows you to mount the product on the wall.

For detailed information on installing the wall mount, see the instructions provided with the wall mount. We recommend you contact a technician for assistance when installing the wall mount bracket. Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the wall mount on your own.

Wall Mount Kit Specifications (VESA)

Note

Install your wall mount on a solid wall perpendicular to the floor. Before attaching the wall mount to surfaces other than plaster board, please contact your nearest dealer for additional information. If you install the product on a ceiling or slanted wall, it may fall and result in severe personal injury.

Note

•Standard dimensions for wall mount kits are shown in the table below.

•Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided.

•Do not use screws that do not comply with the VESA standard screw specifications.

•Do not use screws that are longer than the standard length or do not comply with the VESA standard screw specifications. Screws that are too long may cause damage to the inside of the product.

•For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on the wall mount specifications.

•Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to personal injury. Samsung is not liable for these kinds of accidents.

Introduction

•Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions.

•Do not mount the product at more than a 15 degree tilt.

•Always have two people mount the product on a wall.

Model Name	VESA screw hole specs (A	Standard Screw	Quantity
	* B) in millimeters
460DR-2	400 x 400	M8	4

Warning / Caution

Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric shock.

Remote Control (RS232C)

Cable connections

interface	RS232C(9 pin)

pin	TxD(No.2) RxD(No.3) GND(No.5)

Bits rate	9600 bps

Data Bits	8 bit

Parity	None

Stop Bits	1 bit

Flow control	None

Maximum length	15 m (only shielded type)

• Pin assignment

	Pin	Signal

	1	Data Carrier Detect

	2	Received Data

	3	Transmitted Data

	4	Data Terminal Ready

	5	Signal Ground

		Introduction

	6	Data Set Ready

	7	Request to Send

	8	Clear to Send

	9	Ring Indicator

•RS232C cable Connector : 9-pin D-Sub Cable : Cross cable

-P1-		-P1-			-P2-		-P2-
FEMALE	Rx	2	---------	>	3	Tx	FEMALE
	Tx	3	<---------		2	Rx
	Gnd	5	----------		5	Gnd

•Connecting method

Control codes

•

Get control

Header

command

DATA Length

CheckSum

0xAA

command type

•

Set control

Header

command

DATA

CheckSum

Length

Introduction

0xAA	command	1	Value
	type

•commanding words

No.	command type	command	Value range

1	Power control	0x11	0~1

2	Volume control	0x12	0~100

3	Input source control	0x14	-

4	Screen Mode control	0x18	-

5	Screen Size control	0x19	0~255

6	PIP on/off control	0x3C	0~1

7	Auto adjustment control	0x3D	0

8	Video wall Mode control	0x5C	0~1

9	Safety Lock	0x5D	0~1

-ID should show hexadecimal value of assigned ID, but ID 0 should be 0xFF.

-Every communication will be made in hexadecimals and Checksum is the sum of all remainings. If it exceeds two digits,for example, it is 11+FF+01+01=112, discard the number in the first digit like below.

example)PowerOn&ID=0

Header	command		DATA	DATA 1
		ID	Length		CheckSum
0xAA	0x11		1	Power


Header	command		DATA	DATA 1
		ID	Length		12
0xAA	0x11		1	1

If you want to control every mechanism connected with Serial Cable regardless of its ID, set ID part to "0xFE" and send commands. At the time, each product will follow commands but it will not respond with ACK.

• Power Control

•

Function

Personal Computer turns TV or Monitor power ON/OFF.

• Get Power ON/OFF Status

Header

command

DATA Length

CheckSum

0xAA

0x11

•

Set Power ON/OFF

Header

command

DATA

CheckSum

Length

Introduction

0xAA

0x11

Power

Power : Power code to be set on TV or Monitor.

1 : Power ON

0 : Power OFF

•

Ack

Header

com-

DATA

Ack/Nak

r-CMD

Val1

Check

mand

Length

Sum

0xAA

0xFF

‘A’

0x11

Power

Power : Same as above

•

Nak

Header

com-

DATA

Ack/Nak

r-CMD

Val1

Check

mand

Length

Sum

0xAA

0xFF

‘N’

0x11

ERR

ERR : Error code that shows what occurred error is.

• Volume Control

•

Function

Personal Computer changes volume of TV or Monitor.

•

Get Volume Status

Header

command

DATA Length

CheckSum

0xAA

0x12

•

Set Volume

Header

command

DATA

Length

CheckSum

0xAA

0x12

Volume

Volume : Volume value code to be set on TV or Monitor. (0 ~ 100)

•

Ack

Header

com-

DATA

Ack/Nak

r-CMD

Val1

Check

mand

Length

Sum

0xAA

0xFF

‘A’

0x12

Volume

Volume : Same as above

Introduction

•

Nak

Header

com-

DATA

Ack/Nak

r-CMD

Val1

Check

mand

Length

Sum

0xAA

0xFF

‘N’

0x12

ERR

ERR : Error code that shows what occurred error is.

• Input Source Control

•

Function

Personal Computer changes input source of TV or Monitor.

• Get Input Source Status

Header

command

DATA Length

CheckSum

0xAA

0x14

•

Set Input Source

Header

command

DATA

Length

CheckSum

0xAA

0x14

Input Source

Input Source : Input Source code to be set on TV or Monitor.

0x14

0x1E

BNC

0x18

DVI

0x0C

0x04

S-Video

0x08

Component

0x20

MagicInfo

0x1F

DVI_VIDEO

0x30

RF(TV)

0x40

DTV

0x21

HDMI1

0x22

HDMI1_PC

0x23

HDMI2

0x24

HDMI2_PC

0x25

DisplayPort

Caution

DVI_VIDEO, HDMI1_PC, HDMI2_PC → Get Only

In the case of MagicInfo, only possible with models include MagicInfo.

Introduction

In the case of TV, only possible with models include TV.

•

Ack

Header

com-

DATA

Ack/Nak

r-CMD

Val1

mand

Length

Check

0xAA

0xFF

‘A’

0x14

Input

Sum

Source

Input Source : Same as above

•

Nak

Header

com-

DATA

Ack/Nak

r-CMD

Val1

Check

mand

Length

Sum

0xAA

0xFF

‘N’

0x14

ERR

ERR : Error code that shows what occurred error is.

• Screen Mode Control

•

Function

Personal Computer changes "Screen Mode" of TV or Monitor.

Cannot be controlled when Video Wall is on.

Caution

Only works with models include TV.

• Get Screen Mode Status

Header

command

DATA Length

CheckSum

0xAA

0x18

•

Set Picture Size

Header

command

DATA

Length

CheckSum

0xAA

0x18

Screen

Mode

Screen Mode : Screen Mode code to be set on TV or Monitor.

0x01

16 : 9

0x04

Zoom

0x31

Wide Zoom

0x0B

4 : 3

•Ack

Introduction

Header

com-

DATA

Ack/Nak

r-CMD

Val1

mand

Length

Check

0xAA

0xFF

‘A’

0x18

Screen

Sum

Mode

Screen Mode : Same as above

•

Nak

Header

com-

DATA

Ack/Nak

r-CMD

Val1

Check

mand

Length

Sum

0xAA

0xFF

‘N’

0x18

ERR

ERR : Error code that shows what occurred error is.

• Screen Size Control

•

Function

Personal Computer recognizes the screen size of TV or Monitor.

• Get Screen Size Status

Header

command

DATA Length

CheckSum

0xAA

0x19

•

Ack

Header

com-

DATA

Ack/Nak

r-CMD

Val1

mand

Length

Check

0xAA

0xFF

‘A’

0x19

Screen

Sum

Size

Screen Size : Screen Size of TV or Monitor. (Range : 0 ~ 255, Unit : Inch)

•

Nak

Header

com-

DATA

Ack/Nak

r-CMD

Val1

Check

mand

Length

Sum

0xAA

0xFF

‘N’

0x19

ERR

ERR : Error code that shows what occurred error is.

• PIP ON / OFF Control

•

Function

The PC turns the PIP function of TV or Monitor ON / OFF.

This does not operate in MagicInfo mode.

Introduction

• Get the PIP ON / OFF Status

Header

command

DATA Length

CheckSum

0xAA

0x3C

• Set the PIP ON / OFF

Header

command

DATA

Length

CheckSum

0xAA

0x3C

PIP

PIP : The PIP ON / OFF code to set for the TV or Monitor.

1 : PIP ON

0 : PIP OFF

•

Ack

Header

com-

DATA

Ack/Nak

r-CMD

Val1

Check

mand

Length

Sum

0xAA

0xFF

‘A’

0x3C

PIP

PIP : Same as above

•

Nak

Header

com-

DATA

Ack/Nak

r-CMD

Val1

Check

mand

Length

Sum

0xAA

0xFF

‘N’

0x3C

ERR

ERR : Error code that shows what occurred error is.

• Auto Adjustment Control (PC, BNC Only)

•

Function

Personal Computer controls PC system screen automatically.

• Get Auto Adjustment Status

None

•

Set Auto Adjustment

Header

command

DATA

Length

CheckSum

0xAA

0x3D

Auto Adjust-

ment

Auto Adjustment : 0x00 (Always)

Introduction

•

Ack

Header

com-

DATA

Ack/Nak

r-CMD

Val1

mand

Length

Check

0xAA

0xFF

‘A’

0x3D

Auto Ad-

Sum

justment

•

Nak

Header

com-

DATA

Ack/Nak

r-CMD

Val1

Check

mand

Length

Sum

0xAA

0xFF

‘N’

0x3D

ERR

ERR : Error code that shows what occurred error is.

• Video Wall Mode Control

•

Function

Personal Computer converts Video Wall Mode of TV or Monitor when Video Wall is

ON.

Only works with TV or Monitor where Video Wall is on.

Does not operate in MagicInfo.

• Get Video Wall Mode

Header

command

DATA Length

CheckSum

0xAA

0x5C

• Set Video Wall Mode

Header

command

DATA

Length

CheckSum

0xAA

0x5C

Video Wall

Mode

Video Wall Mode : Video Wall Mode code to be set on TV or Monitor.

1 : Full

0 : Natural

•

Ack

Header

com-

DATA

Ack/Nak

r-CMD

Val1

mand

Length

Check

Video

Sum

0xAA

0xFF

‘A’

0x5C

Wall

Mode

Video Wall Mode : same as above

Introduction

•

Nak

Header

com-

DATA

Ack/Nak

r-CMD

Val1

Check

mand

Length

Sum

0xAA

0xFF

‘N’

0x5C

ERR

ERR : Error code that shows what occurred error is.

• Safety Lock

•

Function

Personal Computer turns Safety Lock function of TV or Monitor ON / OFF.

Can operate regardless of whether power is ON / OFF.

• Get Safety Lock Status

Header

command

DATA Length

CheckSum

0xAA

0x5D

• Set Safety Lock Enable / Disable

Header

command

DATA

Length

CheckSum

0xAA

0x5D

Safety Lock

Safety Lock : Lock code to be set on TV or Monitor.

1 : ON

0 : OFF

•

Ack

Header

com-

DATA

Ack/Nak

r-CMD

Val1

mand

Length

Check

0xAA

0xFF

‘A’

0x5D

Safety

Sum

Lock

Safety Lock : Same as above

•

Nak

Header

com-

DATA

Ack/Nak

r-CMD

Val1

mand

Length

Check

0xAA

0xFF

‘N’

0x5D

Safety

Sum

Lock

ERR : Error code that shows what occurred error is.

+ 113 hidden pages