Prince Castle 755HM16 Installation Manual

0 (0)

Operation

Manual

Timers

755 Series

Product Identification

The Prince Castle Model 755 Series Multi-display 10-Channel Timer and 16-Channel Timer are easy-to-use timers that count down in minutes and seconds, or hours and minutes. Each channel has its own display and can be programmed independently. Slide in replaceable menu strips identify the product being timed on each channel, and are replaceable as restaurant menus change. Both auditory and visual signals are used to alert busy staff people when a function is complete.

The Prince Castle Model 755 Series Single-display 4-Channel Timer and 10-Channel Timer are easy-to-use timers that count down in minutes and seconds, or hours and minutes. Each channel can be programmed independently. Slide in replaceable menu strips identify the product being timed on each channel, and are replaceable as restaurant menus change. Both auditory and visual signals are used to alert busy staff people when a timing function is completed.

LIMITED WARRANTY

This product is warranted to be free from defects in material and/or workmanship for a period of 1 year from date of original installation, not to exceed 18 months from the date of manufacture.

Any component which proves to be faulty in material and/or workmanship will be replaced or repaired (at the option of Prince Castle, Inc.) without cost to the customer for parts and labor. This equipment is portable; charges for on-location service (e.g., trip charges, mileage) are not included in the provisions of this warranty.

This warranty is subject to the following exceptions/conditions:

Use of any non-genuine Prince Castle parts voids this warranty.

All labor to be performed during regular work hours. Overtime premium (the incremental amount) will be charged to the customer.

Damage caused by carelessness, neglect and/or abuse (e.g., dropping, tampering or altering parts, equipment damaged in shipment, by fire, flood or an act of God) is not covered under this warranty.

All problems due to operation at voltages other than that specified on equipment nameplates are not covered by this warranty. Conversion to correct voltage is the customer’s responsibility.

This equipment must be serviced by Prince Castle Authorized Service Agency or a Prince Castle Service Technician during the warranty period.

The power cord on this product is rated for a maximum surface temperature of 194°F (90°C). If the cord comes into contact with the fryer or rethermalizer or any other heated surface, it may be damaged and/or cause damage to the product and/or injury to the user. The power cord may also be damaged if placed directly in the path of the high temperature exhaust emitting from the flue of the fryer or rethermalizer. Damage resulting from any such misuse may result in a voided Warranty at the sole discretion of the manufacturer.

TABLE OF CONTENTS

Product Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 – 7

Exploded View and Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8

355 East Kehoe Blvd. • Carol Stream, IL 60188 USA Telephone: 630-462-8800 • Toll Free: 1-800-PCASTLE Fax: 630-462-1460 • www.princecastle.com

755-503revB

Printed in USA 12/06 © 2006

Prince Castle 755HM16 Installation Manual

Timers

755 Series

Safety Information

WARNING

Indicates information important to the proper operation of the unit. Failure to observe may result in damage to the equipment and/or severe bodily injury or death.

CAUTION

Indicates information important to the operation of the unit. Failure to observe may result in damage to the equipment.

Important!

Prince Castle reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.

Installation

Remove the unit from the carton and inspect for signs of damage. If there is damage to the unit:

Notify the freight carrier (e.g. UPS) within 24 hours,

Save carton and packaging materials for inspection purposes,

Contact your local dealer, or if purchased directly, the Prince Castle Sales Department at 1-800-722-7853 or 630-462-8800 to arrange for a replacement unit.

NOTE: When installing this unit, the ambient temperature at the mounting site should not exceed 100°F (37.8°C).

CAUTION

All electrical connections must be in accordance with local electrical codes and any other applicable codes.

Plug the unit into an applicable electrical receptacle.

Cleaning

Use ONLY a clean damp cloth, wipe the face and other surfaces on the Model 755 Series Timer, as necessary. If desired, a mild soap may also be used.

NEVER use chemicals and/or degreaser of any kind! Long term use of certain chemicals has a negative effect on the surface of the timer, making it brittle and easily damaged.

Operation

1Display

Individual bi-colored LED for each channel. When activated, the LED for each channel will turn green for the length of the entire timing cycle. When the timing cycle ends, the LED will flash red.

One 4-digit, 7-segment numeric display for Single Display Timers and a similar display for each channel on Multiple Display Timers.

On Single Display models with multi-timers running, the channel with the least time remaining will blink its LED.

If the time is in Hours-Minutes (H:M) the colon in the middle of the 4-digits will flash. If the time is in Minutes-Seconds (M:S) the colon in the middle of the 4-digits will be on continuously.

Every channel can be programmed for 2 separate menus (also known as dayparts), with both having different timing cycles. The different Menus are indicated by the display in the idle state as follows.

(Menu 1)

or

(Menu 2)

Single Display Models

To start a channel’s timing cycle press the button associated with that channel (a short beep sounds). If that is the only channel running, the display will show the time countdown for that channel. When multiple timers are running, the display will show the time countdown for the channel with the least amount of time remaining (blinking LED indicates this channel).

To temporarily view the remaining time of any other channel, press and hold its button.

At the conclusion of a timing cycle the display flashes “0”. After the end alarm stops the display will return to the idle state if only one channel was timing or if other channels are timing it will now display the time countdown of the channel with the least amount of time remaining.

To cancel any channel’s timing cycle, press that channel’s button three times in quick succession (within three seconds). The channel will return to the idle state.

Each channel of the timer operates in an identical manner.

Multi Display Models

To start a channel’s timing cycle press the button associated with that channel (a short beep sounds). That channel’s display will show the time countdown.

At the conclusion of a timing cycle the display will show either “diSc” (discard) or “donE” (done). This indication is programmable. After the end alarm stops the display will return to the idle state.

To cancel any channel’s timing cycle, press that channel’s button three times in quick succession (within three seconds). The channel will return to the idle state.

Each channel of the timer operates in an identical manner.

Prince Castle reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.

Printed in USA 12/06 © 2006

2

755-503revB

Timers

755 Series

Operation (continued)

2 Channel Defaults

HS4

 

Menu 1

Menu 2

 

 

 

 

Cycle Time

Cycle Time

 

 

 

Channel 1

04:00

04:00

 

 

 

Channel 2

04:00

04:00

 

 

 

Channel 3

06:00

06:00

 

 

 

Channel 4

06:00

06:00

 

 

 

Bold italic times are in Hours:Minutes. All other times are in Minutes:Seconds. Action alarm time = 0 (feature turned off).

HS10

 

Menu 1

Menu 2

 

 

 

 

Cycle Time

Cycle Time

 

 

 

Channel 1

15:00

15:00

 

 

 

Channel 2

15:00

15:00

 

 

 

Channel 3

15:00

15:00

 

 

 

Channel 4

15:00

15:00

 

 

 

Channel 5

15:00

15:00

 

 

 

Channel 6

15:00

15:00

 

 

 

Channel 7

15:00

15:00

 

 

 

Channel 8

15:00

15:00

 

 

 

Channel 9

30:00

30:00

 

 

 

Channel 10

30:00

30:00

 

 

 

HM10 — Menu 1

 

Cycle Time

Alarm

Cycle End

 

 

 

 

 

Time

Time

Name

 

 

 

 

Channel 1

30:00

0:00:00

DISC

 

 

 

 

Channel 2

30:00

0:00:00

DISC

 

 

 

 

Channel 3

30:00

0:00:00

DISC

 

 

 

 

Channel 4

30:00

0:00:00

DISC

 

 

 

 

Channel 5

30:00

0:00:00

DISC

 

 

 

 

Channel 6

30:00

0:00:00

DISC

 

 

 

 

Channel 7

30:00

0:00:00

DISC

 

 

 

 

Channel 8

30:00

0:00:00

DISC

 

 

 

 

Channel 9

04:00

0:00:00

DISC

 

 

 

 

Channel 10

04:00

0:00:00

DISC

 

 

 

 

HM10 — Menu 2

 

 

 

 

 

 

 

 

Cycle Time

Alarm

Cycle End

 

 

 

 

 

Time

Time

Name

 

 

 

 

Channel 1

30:00

0:00:00

DISC

 

 

 

 

Channel 2

30:00

0:00:00

DISC

 

 

 

 

Channel 3

30:00

0:00:00

DISC

 

 

 

 

Channel 4

30:00

0:00:00

DISC

 

 

 

 

Channel 5

30:00

0:00:00

DISC

 

 

 

 

Channel 6

30:00

0:00:00

DISC

 

 

 

 

Channel 7

30:00

0:00:00

DISC

 

 

 

 

Channel 8

30:00

0:00:00

DISC

 

 

 

 

Channel 9

04:00

0:00:00

DISC

 

 

 

 

Channel 10

04:00

0:00:00

DISC

 

 

 

 

Bold italic times are in Hours:Minutes. All other times are in Minutes:Seconds. Action alarm time = 0 (feature turned off).

HM16 — Menu 1

 

 

Cycle Time

Alarm

Cycle End

 

 

 

 

 

 

 

Time

Time

Name

 

 

 

 

Channel 1

15:00

0:00:00

DISC

 

 

 

 

Channel 2

15:00

0:00:00

DISC

 

 

 

 

Channel 3

15:00

0:00:00

DISC

 

 

 

 

Channel 4

15:00

0:00:00

DISC

 

 

 

 

Channel 5

15:00

0:00:00

DISC

 

 

 

 

Channel 6

15:00

0:00:00

DISC

 

 

 

 

Channel 7

15:00

0:00:00

DISC

 

 

 

 

Channel 8

15:00

0:00:00

DISC

 

 

 

 

Channel 9

30:00

0:00:00

DISC

 

 

 

 

Channel 10

30:00

0:00:00

DISC

 

 

 

 

Channel 11

30:00

0:00:00

DISC

 

 

 

 

Channel 12

30:00

0:00:00

DISC

 

 

 

 

Channel 13

30:00

0:00:00

DISC

 

 

 

 

Channel 14

30:00

0:00:00

DISC

 

 

 

 

Channel 15

30:00

0:00:00

DISC

 

 

 

 

Channel 16

30:00

0:00:00

DISC

 

 

 

 

 

Bold italic times are in Hours:Minutes. All other times are in Minutes:Seconds. Action alarm time = 0 (feature turned off).

HM16 — Menu 2

 

 

Cycle Time

Alarm

Cycle End

 

 

 

 

 

 

 

Time

Time

Name

 

 

 

 

Channel 1

15:00

0:00:00

DISC

 

 

 

 

Channel 2

15:00

0:00:00

DISC

 

 

 

 

Channel 3

15:00

0:00:00

DISC

 

 

 

 

Channel 4

15:00

0:00:00

DISC

 

 

 

 

Channel 5

15:00

0:00:00

DISC

 

 

 

 

Channel 6

15:00

0:00:00

DISC

 

 

 

 

Channel 7

15:00

0:00:00

DISC

 

 

 

 

Channel 8

15:00

0:00:00

DISC

 

 

 

 

Channel 9

30:00

0:00:00

DISC

 

 

 

 

Channel 10

30:00

0:00:00

DISC

 

 

 

 

Channel 11

30:00

0:00:00

DISC

 

 

 

 

Channel 12

30:00

0:00:00

DISC

 

 

 

 

Channel 13

30:00

0:00:00

DISC

 

 

 

 

Channel 14

30:00

0:00:00

DISC

 

 

 

 

Channel 15

30:00

0:00:00

DISC

 

 

 

 

Channel 16

30:00

0:00:00

DISC

 

 

 

 

 

Bold italic times are in Hours:Minutes. All other times are in Minutes:Seconds. Action alarm time = 0 (feature turned off).

755-503revB

3

Printed in USA 12/06 © 2006

Loading...
+ 5 hidden pages