Powerfix Z29618-BS User Manual
LED WORK LAMP
Operation and Safety Notes
Z29618-BS
6
1
2
3
7
4
6 5
LED Work Lamp
Q
Introduction
Familiarise yourself with the product
before using it for the first time. In addi-
tion please refer carefully to the operating
instructions below and the safety advice. Use the
product only as described and for the indicated
purpose. Keep these instructions in a safe place.
If you pass the product on to anyone else, please
ensure that you also pass on all the documentation.
Q
Proper use
The product is intended for providing illumination
in dry indoor rooms and in outdoor environments.
If used outdoors the mains adapter must be protected from moisture and the weather. Any other
use or modification of the product constitute
improper use and pose a risk of short circuits, fire,
electric shocks and damage to the product. The
manufacturer is not liable for damage caused by
improper use. The product is not intended for
commercial use.
Q
Description of parts and
features
1
Hook
2
Magnetic mount
3
Mains adapter
4
Car adapter (for cigarette lighter socket)
5
ON / OFF switch
6
Power input connection socket
7
Indicator LED
Q
Technical data
Light bulb: 23 LEDs (white,
non-replaceable)
Light intensity : approx. 12,000 mcd
(millicandela)
Lamp rechargeable
batteries: 3 x AA NiMH, 1000 mAh
(not replaceable)
Charging time: approx. 4 to 6 hours
Burn time: approx. 3 hours (with fully
charged battery)
Lifespan of LEDs: approx. 20,000 hours
Protection class:
System of protection: IP44
Adapter:
Input: 230 V ~ 50 Hz
Output: 6 V
Model: YX-0603
, 300 mA
Protection class:
System of protection: IP20
Cigarette lighter:
Input: 12 V
Output: 12 V , 240 mA
Q
Scope of delivery
1 LED inspection lamp
1 Mains adapter
1 Car adapter for cigarette lighter socket
1 Magnetic mount
1 Operating instructions
Safety instructions
J
Never leave children alone and unsupervised
with the packaging material. There is always
a risk of suffocation if children play with the
packaging material. Children often underestimate risks. Always keep children away from
the packaging material. This product is not a
toy.
J Children or persons who lack the knowledge
or experience to use the device or whose
physical, sensory or intellectual capacities
are limited must never be allowed to use the
device without supervision or instruction by a
WARNING!
LIFE AND RISK OF ACCIDENTS
FOR INFANTS AND CHILDREN!
DANGER TO
GB / IEGB / IEGB / IEGB / IEGB / IE
person responsible for their safety. Children
must never be allowed to play with the device.
J This product is not a toy and should be kept
out of the reach of children. Children are not
aware of the dangers associated with handling electrical products.
J Do not use the article if you detect any kind
of damage.
J
explosive environments in which there are
J The LED inspection lamp is protected against
CAUTION! DANGER OF
EXPLOSION! Do not operate
the LED work lamp in potentially
inflam mable vapours, gases or dusts.
water spray. However, the product, mains
adapter and car adapter must never be
immersed in water or other liquids. Failure to
observe this advice will create the risk of elec-
GB / IE GB / IE GB / IE GB / IE GB / IE GB / IE GB / IE
tric shock! Never hang the product near a
washbasin, pond and the like.
J Connect the LED work lamp to a properly
installed mains socket or a suitable cigarette
lighter socket only. The voltages in each case
must comply with information given in the
section “Technical data”.
J Ensure that the electrical socket is easily acces-
sible so that you can pull the plug quickly out
of the socket if necessary.
J Do not carry out any modifications or repairs
to the product yourself. The LEDs cannot and
must not be replaced.
m CAUTION! The protective surround to the
LEDs cannot be replaced. Dispose of the LED
inspection lamp if you discover cracks or
signs of fracture on the protective surround.
J Dispose of the product if the LED inspection
lamp, mains adapter or car adapter is damaged.
J Never connect the LED work lamp to a power
supply socket if the LED work lamp, power
lead or socket is damaged or the LED work
lamp has been dropped.
J Ensure that the power lead cannot become
damaged by sharp edges or hot objects.
Unwind all the lead completely before use.
J Keep easily flammable materials away the
product. Never hang objects above the LED
work lamp or the mains adapter and never
cover them.
J Pull the mains adapter / plug out of the mains
socket / cigarette lighter socket when you are
not using the LED work lamp or before you
clean it. Do this as well if signs of a fault
develop during use or charging, e.g. smoke,
burning smell etc., or during a storm. When
doing this, pull directly on the mains adapter / plug and not on the lead.
J Protect the product against heat, cold, strong
vibrations and impacts.
J
optical appliances such as magnifying glasses
J Never point the LED beam at reflective surfaces,
CAUTION! LED RADIATION.
Avoid damage to eyes! Never
look directly at the LED. Never use
or the like to look at the LED. Protect yourself
and your environment by taking proper precautions.
people or animals. This could result in blindness or irritation of the eyes. Even weak LEDs
could result in eye damage.
J Do not attach the hook 1 to hot objects. The
dead weight of the LED work lamp might
cause the hook to deform or bend out of shape.
Q
Before use
Q
Charging the LED inspection
lamp
Note: You can charge the LED inspection lamp
from an ordinary domestic mains power outlet or
from the cigarette lighter socket in your vehicle.
Tip: We recommend that you charge the LED
inspection lamp from an ordinary domestic mains
power outlet to avoid draining your vehicle’s
battery.
CAUTION! Do not connect the LED inspection
lamp to the cigarette lighter socket of your vehicle
if the vehicle battery is old or degraded. Failure
to observe this advice may result in your vehicle’s
engine not starting.
Note: To use the LED inspection lamp without an
adapter, you must first charge the integral rechargeable batteries. It takes between 4 and 6 hours to
charge the integral batteries. The rechargeable
batteries are permanently installed in the handle
of the LED inspection lamp.
Note: Charge the LED inspection lamp for approximately 12 hours before first use.
Note: Charge the LED inspection lamp at least
once a month, if it is to remain unused for an
extended period of time.
Note: If the LED inspection lamp has not been
charged for an extended period of time (approx.
2 months), you could find that the integral rechargeable batteries have entered a dormant state.
Charge and discharge the LED inspection lamp a
number of times in succession to reactivate the
integral rechargeable batteries.
j Switch off the LED inspection lamp during the
charging process (set the ON / OFF switch
5
to position 0).
j Remove the rubber protection cap from the
bottom of the LED inspection lamp.
j Insert the power output connection plug of
the mains adapter
into the power input connection socket
the handle of the LED inspection lamp.
Note: During charging from a cigarette lighter
socket, ensure that the plug is always completely
inserted into the cigarette lighter socket of the
vehicle. Failure to observe this advice may
result in risk of fire from overheating.
j Insert the mains adapter
socket or the car adapter
3
or the car adapter 4
3
into a mains
4
into the ciga-
6
in
rette lighter socket of your vehicle.
Note: The product has an overcharging
protection system. Nevertheless, you should
disconnect the LED inspection lamp from the
mains once the charging process is complete.
Note: The indicator LED
7
illuminates red
during the charging process. When the
charging process is complete, the indicator
7
LED
illuminates green. When the indicator
7
LED
illuminates green, pull the mains
adapter
adapter
3
out of the mains socket or the car
4
out of the cigarette lighter socket.
Disconnect the adapter from the LED inspection
lamp to prevent the batteries from discharging
themselves.
j Place the rubber protection cap back on the
power input connection socket
6
before you
start to use the LED inspection lamp again.
Otherwise water could enter the power input
connection socket
6
if the LED inspection
lamp is used outdoors.
Q
Use
m CAUTION – RISK OF ACCIDENT! If at
all possible, do not use the LED inspection lamp
in a moving vehicle. If the LED inspection lamp is
used in a vehicle, it must not be allowed to endanger the safety of the driver or passengers. Always
store and secure the LED inspection lamp in such
a way that there is no risk of injury from or damage to the product, even during full braking.
Note: You can secure the LED inspection lamp in
place using the hook
Clamp the magnetic mount
1
or magnetic mount 2.
2
to the LED’s pro-
tective surround. Then hold the LED inspection
lamp against a magnetic surface.
Q
Using the LED inspection lamp
disconnected from a power
supply
j Fully charge the LED inspection lamp, as
described in the section on “Charging the
LED inspection lamp”.
j Set the ON / OFF switch
5
to position I to
switch on the LED inspection lamp.
j Set the ON / OFF switch
5
to position 0 to
switch off the LED inspection lamp.
Q
Using the LED inspection lamp
connected to a power supply
m CAUTION! RISK OF INJURY! Position the
power lead so that it does not create a trip hazard.
m CAUTION RISK OF ACCIDENT! Do not
connect or use the LED inspection lamp if you are
in moving traffic, for example driving a vehicle.
The LED inspection lamp is not intended to be
used as an indoor lighting fixture or a reading
lamp!
j Remove the rubber protection cap from the
power input connection socket
6
.
j Insert the power output connection plug of the
mains adapter
into the power input connection socket
3
or of the car adapter 4
6
in
the handle of the LED inspection lamp.
j Insert the mains adapter
mains socket or the car adapter
3
into a 230 V ~
4
into the
cigarette lighter socket of your vehicle.
j Set the ON / OFF switch
5
to position I to
switch on the LED inspection lamp.
m CAUTION! If the LED inspection lamp is con-
nected to the mains by the mains adapter
3
in this state it is intended exclusively for
indoor use.
j Set the ON / OFF switch
5
to position 0 to
switch off the LED inspection lamp.
Q
Troubleshooting
Fault Possible causes and cures
No
functions
- Mains adapter
4
is not fully inserted.
3
or car adapter
Fault Possible causes and cures
Q
Maintenance and cleaning
,
Indicator
7
LED
does not
illuminate
Charging
takes a
very long
time
When connected to a
cigarette lighter socket:
- Is the cigarette lighter socket
supplied
with power? Some
cigarette lighter sockets only
supply power with the ignition
switched on.
- Check the fuse in the vehicle.
When connected to a
cigarette lighter socket:
- Vehicle battery too weak?
The product requires no maintenance. The LEDs
cannot be replaced.
J Disconnect the product from the power supply
before you clean it.
J Never immerse the product in water or other
liquids.
J Do not use corrosive cleaning agents.
j Clean the product regularly with a dry, fluff-
free cloth. Use a slightly moist cloth to remove
any stubborn dirt.
Q
Disposal
The packaging is made entirely of
recyclable materials, which you may
dispose of at local recycling facilities.
GB / IEGB / IEGB / IEGB / IEGB / IEGB / IEGB / IE
Contact your local refuse disposal authority for
more details of how to dispose of your worn-out
product.
To help protect the environment,
please dispose of the product properly
when it has reached the end of its useful life and not in the household waste.
Information on collection points and
their opening hours can be obtained
from your local authority.
Defective or exhausted rechargeable batteries
must be recycled in accordance with Directive
2006 / 66 / EC. Return the battery and / or the
device through the appropriate collection facilities.
GB / IE GB / IE GB / IE
Improper disposal of recharge-
able batteries can damage the
Pb
environment!
Rechargeable batteries must not be disposed of
with the household refuse. They may contain toxic
heavy metals and require to be handled as special
waste. The chemical symbols of heavy metals are:
Cd = cadmium, Hg = mercury, Pb = lead
EMC
Product Description:
LED Work Lamp
Model No.: Z29618-BS
Version: 12 / 2010
Level of information: 11 / 2010
ID No.: Z29618-BS112010-6
© by ORFGEN Marketing
IAN 58812
Milomex Ltd.
c / o Milomex Services
Hilltop Cottage
Barton Road
Pulloxhill
Bedfordshire
MK45 5HP
UK
Loading...