ORDER NO. MD0410497C1
A6
CD Stereo System
SA-AK330P
SA-AK330PC
Colour
(K)... Black Type (For P/PC)
(S)... Silver Type (For P only)
Specifications
n AMPLIFIER SECTION |
|
Sensitivity |
|
|
FTC output power |
|
S/N 20 dB (at 1000 kHz) |
560 µV/m |
|
THD 10%, both channels driven |
|
Audio performance (Amplifier) |
|
|
100 Hz - 3 kHz |
|
Input sensitivity/Input impedance |
|
|
(Low channel) |
64 W per channel (5 Ω) |
Aux |
250 mV,14.7 kΩ |
|
3 kHz -10 kHz |
|
Phone jack |
|
|
(High channel) |
60 W per channel (5 Ω) |
Terminal |
Stereo, 3.5 mm (1/8”) jack |
|
Total Bi-Amp power |
248 W |
n CASSETTE DECK SECTION |
|
|
RMS output power |
|
Track system |
4 track, 2 channel |
|
THD 10%, both channels driven |
|
Heads |
|
|
1 kHz, |
|
Record/playback |
Solid permalloy head |
|
(Low channel) |
90 W per channel (5 Ω) |
Erasure |
Double gap ferrite head |
|
10 kHz, |
|
Motor |
DC servo motor |
|
(High channel) |
90 W per channel (5 Ω) |
Recording system |
AC bias 100 kHz |
|
Total Bi-Amp power |
360 W |
Erasing system |
AC erase 100 kHz |
|
n FM/AM TUNER, TERMINAL SECTION |
Tape speed |
4.8 cm/s (1 7/8 ips) |
||
Preset station |
FM 15 stations |
Overall frequency response (+3 dB, -6 dB at DECK OUT) |
||
|
AM 15 stations |
NORMAL |
35 Hz - 14 kHz |
|
Frequency Modulation (FM) |
|
S/N |
50 dB (A weighted) |
|
Frequency range |
|
Wow and flutter |
0.18 % (WRMS) |
|
|
87.9 - 107.9 MHz (200 kHz steps) |
Fast forward and rewind time |
Approx. 120 seconds with |
|
|
87.5 - 108.0 MHz (100 kHz steps) |
|
|
C-60 cassette tape |
Sensitivity |
2.5 µV (IHF) |
n DISC SECTION |
|
|
S/N 26 dB |
2.2 µV |
Discs played [8 cm (3”) or 12 cm (5”)] |
||
Antenna terminal(s) |
75 Ω (unbalanced) |
(1) CD-Audio (CD-DA) |
|
|
Amplitude Modulation (AM) |
|
(2) CD-R/RW (CD-DA, MP3 formatted discs) |
||
Frequency range |
520 - 1710 kHz (10 kHz steps) |
(3) MP3 |
|
|
|
|
|
|
|
|
|
|
© 2004 Matsushita Electric Industrial Co. Ltd.. All |
|
|
|
|
rights reserved. |
Unauthorized copying and |
|
|
|
distribution is a violation of law. |
|
|
|
|
|
|
SA-AK330P / SA-AK330PC |
|
|
Bit rate |
|
|
MP3 |
32 kbps - 320 kbps |
|
Sampling frequency |
|
|
MP3 |
32 kHz, 44.1 kHz, 48 kHz |
|
CD |
44.1 kHz |
|
Decoding |
16 bit linear |
|
Digital filter |
8 fs |
|
D/A converter |
MASH (1 bit DAC) |
|
Pickup |
|
|
Wavelength |
780 nm |
|
Beam Source |
Semiconductor laser |
|
Audio output (Disc) |
|
|
Number of channels |
2 (Stereo) (FL,FR) |
|
n GENERAL |
|
|
Power Supply |
AC 120 V, 60Hz |
|
Power consumption |
238 W |
|
Power consumption in standby |
0.38 W |
mode |
|
Dimensions (W x H x D) |
250 x 330 x 341 mm |
|
(9 27/32” x 13” x 13 7/16”) |
Mass |
7.1 kg (15.7 lb.) |
Operating temperature range |
+5 to +35°C (+41 to +95°F) |
Operating humidity range |
5 to 90% RH (no condensation) |
n SYSTEM |
|
SC-AK330 (P) |
Music center: SA-AK330 (P) |
|
Speaker: SB-AK330 (P) |
SC-AK330 (PC) |
Music center: SA-AK330 (PC) |
|
Speaker: SB-AK330 (P) |
Notes: |
|
1.Specifications are subject to change without notice. Mass and dimensions are approximate.
2.Total harmonic distortion is measured by the digital spectrum analyzer.
CONTENTS
|
Page |
Page |
||
1 |
Safety Precaution |
4 |
10.14. Replacement for the cassette lid ass |
34 |
|
1.1. Insulation Resistance Test |
4 |
10.15. Measure for tape trouble |
35 |
2 |
Before Repair and Adjustment |
5 |
11 Checking for major P.C.B. |
36 |
3 |
Protection Circuitry |
5 |
11.1. Checking the Main P.C.B. |
36 |
4 |
Prevention of Electro Static Discharge (ESD) to |
|
11.2. Checking the Transformer P.C.B. |
37 |
|
Electrostatically Sensitive (ES) Devices |
6 |
11.3. Checking the Panel, Deck & Deck Mechanism P.C.B. |
38 |
5 |
Handling the Lead-free Solder |
6 |
11.4. Checking the Power P.C.B. |
39 |
|
5.1. About lead free solder (PbF) |
6 |
12 Self-Diagnostic Function |
40 |
6 |
Handling Precautions For Traverse Deck |
7 |
12.1. Self-diagnostic display |
40 |
7 |
Precaution of Laser Diode |
8 |
12.2. How to enter the Self-Diagnostic Function |
40 |
8 |
Accessories |
9 |
12.3. Cassette Mechanism Test (For error code H01, H02, H03, |
|
9 |
Operation Procedures |
10 |
F01) |
40 |
10 |
Disassembly and Assembly of Main Component |
12 |
12.4. CD Mechanism Test (F15, F26, F16, F17, F27, F28, F29, |
|
|
10.1. Disassembly flow chart |
12 |
F30, H15 & H16) |
40 |
|
10.2. Disassembly of Top Cabinet |
13 |
12.5. To clear all Error code |
41 |
|
10.3. Disassembly of CD Lid |
13 |
12.6. How to get out from Self-Diagnostic function |
41 |
|
10.4. Disassembly of Rear Panel |
15 |
12.7. Power Amplifier Failure (F61) |
41 |
|
10.5. Disassembly of CD Mechanism Unit |
15 |
12.8. Description of Error Code |
41 |
|
10.6. Disassembly of Main P.C.B. |
16 |
13 CD Test Mode Function |
43 |
|
10.7. Disassembly of Power P.C.B. |
16 |
13.1. How to set CD test mode |
43 |
|
10.8. Disassembly of Transformer P.C.B. |
17 |
13.2. CD Automatically Adjustment result indication |
43 |
|
10.9. Disassembly of Front Panel Unit |
18 |
13.3. CD Mecha Aging Test Mode (CR20) |
43 |
|
10.10. Disassembly of Deck Mechanism Unit |
18 |
13.4. Micon ROM Checksum and Version Display Mode |
44 |
|
10.11. CD Mechanism Main Component Replacement |
|
14 Measurements and Adjustments |
45 |
|
Procedures |
19 |
14.1. Cassette Deck Section |
45 |
|
10.12. Replacement for the pinch roller ass and head block |
32 |
14.2. Tuner Section |
45 |
|
10.13. Replacement for the Deck motor ass , capstan belt A, |
|
14.3. Alignment Points |
46 |
|
capstan belt B and winding belt |
32 |
15 Block Diagram |
47 |
2
|
|
|
|
SA-AK330P / SA-AK330PC |
|
16 Voltage Measurement |
54 |
|
18.7. (I) Deck P.C.B. & (J) Deck Mechanism P.C.B. |
80 |
|
17 Schematic Diagram |
56 |
19 |
Wiring Connection Diagram |
81 |
|
17.1. (A) CD Servo Circuit |
57 |
20 |
Illustration of IC , Transistors and Diodes |
82 |
|
17.2. (B) Main (Tuner) Circuit |
59 |
21 |
Terminal Function of IC |
83 |
|
17.3. (B) Main Circuit |
60 |
|
21.1. IC7002 (MN6627953HB) Servo processor/ Digital signal |
||
17.4. (C) Panel Circuit |
65 |
|
processor/ Digital filter/ D/A converter |
83 |
|
17.5. (D) Transformer Circuit, (E) CD Detect Circuit, (F) Spindle |
|
21.2. IC7003 (AN8739SBTE2) Focus coil/ Tracking coil/ |
|
||
Position Circuit & (G) CD Loading Circuit |
67 |
|
Traverse motor/ Spindle motor drive |
83 |
|
17.6. (H) Power Circuit |
68 |
|
21.3. IC2801 (CC2CBJG000564) System Microprocessor |
84 |
|
17.7. (I) Deck Circuit & (J) Mechanism Circuit |
69 |
22 |
Troubleshooting Guide |
86 |
|
18 Printed Circuit Board |
71 |
23 |
Parts Location and Replacement Parts List |
87 |
|
18.1. (A) CD Servo P.C.B. |
71 |
|
23.1. Deck Mechanism (RAA4502-S) |
88 |
|
18.2. (B) Main P.C.B. |
72 |
|
23.2. CD Loading Mechanism (RD-DAC026-S) |
91 |
|
18.3. (C) Panel P.C.B. |
74 |
|
23.3. Cabinet |
94 |
|
18.4. (D) Transformer P.C.B. |
76 |
|
23.4. Electrical Parts List |
96 |
|
18.5. (E) CD Detect P.C.B., (F) Spindle Position P.C.B., (G) CD |
|
23.5. Packing Materials & Accessories Parts List |
104 |
||
Loading P.C.B. & (K) Tuner Pack P.C.B. |
77 |
|
23.6. Packaging |
105 |
|
18.6. (H) Power P.C.B. |
78 |
|
|
|
|
3
SA-AK330P / SA-AK330PC
1 Safety Precaution
(This “Safety Precaution” is applied only in U.S.A.)
1.Before servicing, unplug the power cord to prevent an electric shock.
2.When replacing parts, use only manufacturer’s recommended components for safety.
3.Check the condition of the power cord. Replace if wear or
1.1.Insulation Resistance Test
damage is evident.
4.After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc.
5.Before returning the serviced equipment to the customer, be sure to make the following insulation resistance test to prevent the customer from being exposed to a shock hazard.
1.Unplug the power cord and short the two prongs of the plug with a jumper wire.
2.Turn on the power switch.
3.Measure the resistance value with ohmmeter between the jumper AC plug and each exposed metal cabinet part, such as screwheads, antenna, control shafts, handle brackets, etc.Measure the resistance value with ohmmeter between the jumper AC plug and each exposed metal cabinet part, such as screwheads, antenna, control shafts, handle brackets, etc.
Equipment with antenna terminals should read between 2.7MΩ and 3.9MΩ to all exposed parts*. (Fig.1) Equipment without antenna terminals should read approximately infinity to all exposed parts. (Fig.2) *Note : Some exposed parts may be isolated from the chassis by design. These will read infinity.
4.If the measurement is outside the specified limits, there is a possibility of a shock hazard. The equipment should be repaired and re-checked before it is returned to the customer.
Fig.1
Fig.2
4
SA-AK330P / SA-AK330PC
1.1.1.Caution for fuse replacement
2 Before Repair and Adjustment
Disconnect AC power, discharge Power Supply Capacitors C5820 and C5840 through a 10Ω, 5W resistor to ground. DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices. After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
Current consumption at AC 120V, 60 Hz in NO SIGNAL mode (volume min at CD mode) should be ~500mA.
3 Protection Circuitry
The protection circuitry may have operated if either of the following conditions are noticed:
·No sound is heard when the power is turned on.
·Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are “shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
If this occurs, follow the procedure outlines below:
1.Turn off the power.
2.Determine the cause of the problem and correct it.
3.Turn on the power once again after one minute.
Note :
When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.
5
SA-AK330P / SA-AK330PC
4 Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by electro static discharge (ESD).
1.Immediately before handling any semiconductor component or semiconductor-equiped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.
2.After removing an electrical assembly equiped with ES devices, place the assembly on a conductive surface such as aluminium foil, to prevent electrostatic charge build up or exposure of the assembly.
3.Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4.Use only an anti-static solder remover device. Some solder removal devices not classified as “anti-static (ESD protected)” can generate electrical charge to damage ES devices.
5.Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6.Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminium foil or comparable conductive material).
7.Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8.Minimize body motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).
5 Handling the Lead-free Solder
5.1.About lead free solder (PbF)
Distinction of PbF P.C.B.:
P.C.B.s (manufactured) using lead free solder will have a PbF stamp on the P.C.B.
Caution:
·Pb free solder has a higher melting point than standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher. Please use a high temperature soldering iron. In case of soldering iron with temperature control, please set it to 700 ± 20°F (370 ± 10°C).
·Pb free solder will tend to splash when heated too high (about 1100°F/600°C).
·When soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat the soldering points with the Pb free solder until it melts enough.
6
SA-AK330P / SA-AK330PC
6 Handling Precautions For Traverse Deck
The laser diode in the traverse deck (optical pickup) may break down due to potential difference caused by static electricity of clothes or human body.
So, be careful of electrostatic breakdown during repair of the traverse deck (optical pickup).
· Handling of traverse deck (optical pickup)
1.Do not subject the traverse deck (optical pickup) to static electricity as it is extremely sensitive to electrical shock.
2.To prevent the breakdown of the laser diode, an antistatic shorting pin is inserted into the flexible board (FFC board).
3.Take care not to apply excessive stress to the flexible board (FFC board). When removing or connecting the short pin, finish the job in as short time as possible.
4.Do not turn the variable resistor (laser power adjustment). It has already been adjusted.
Grounding for electrostatic breakdown prevention
1.Human body grounding
Use the anti-static wrist strap to discharge the static electricity from your body.
2.Work table grounding
Put a conductive material (sheet) or steel sheet on the area where the traverse deck (optical pickup) is place, and ground the sheet.
Caution :
The static electricity of your clothes will not be grounded through the wrist strap. So, take care not to let your clothes touch the traverse deck (optical pickup).
Caution when replacing the Traverse Deck
The traverse deck has a short point shorted with solder to protect the laser diode against electrostatics breakdown. Be sure to remove the solder from the short point before making connections.
7
SA-AK330P / SA-AK330PC
7 Precaution of Laser Diode
CAUTION:
This unit utilizes a class 1 laser.
Invisible laser radiation is emitted from the optical pickup lens.
Wavelength: 780nm
When the unit is turned on:
1.Do not look directly into the pick up lens.
2.Do not use optical instruments to look at the pick up lens.
3.Do not adjust the preset variable resistor on the pickup lens.
4.Do not disassemble the optical pick up unit.
5.If the optical pick up is replaced, use the manufacturer’s specified replacement pick up only.
6.Use of control or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
n Use of caution label (Except for U.S.A.)
8
SA-AK330P / SA-AK330PC
8 Accessories
Remote Control
FM Antenna
AC Cord
AM Loop Antenna
9
SA-AK330P / SA-AK330PC
9 Operation Procedures
10
SA-AK330P / SA-AK330PC
11
SA-AK330P / SA-AK330PC
10 Disassembly and Assembly of Main Component
10.1. Disassembly flow chart
The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the servicing.
To assemble the unit, reverse the steps shown in the chart as below.
12
SA-AK330P / SA-AK330PC
10.2. Disassembly of Top Cabinet
Step 1 Remove 2 screws at each side and 5 screws at rear panel.
Step 2 Lift up both sides of the top cabinet, push the top cabinet towards the rear and remove the top cabinet.
10.3. Disassembly of CD Lid
(The CD changer unit can be removed after the CD Lid is removed)
·Follow the (Step 1) - (Step 2) of Item 10.2 - Disassembly of Top Cabinet
·Opening the disc tray automatically (Using Power Supply)
Step 1 Connect the AC power cord.
Step 2 Press the POWER button to power up the main unit.
Step 4 Release the 2 claws, and then remove the CD Lid.
Step 5 Press the OPEN/CLOSE button, the disc tray will close.
Step 3 Press the OPEN/CLOSE button, the disc tray will open automatically.
13
SA-AK330P / SA-AK330PC
Step 2 Release the 2 claws, and then remove the CD lid cover.
Step 6 Press the POWER button to turn the power off.
· [Opening the disc tray manually (Using service tools)]
Step 3 Repeat Step 2 but rotate the gear tools in anti-clockwise direction.
Step 1 Insert the gear tool into the hole on the underside of CD chassis and then rotate in the direction of arrow. The disc tray will be opened.
Step 4 The disc tray will be closed.
14
SA-AK330P / SA-AK330PC
10.4. Disassembly of Rear Panel
· Follow the (Step 1) - (Step 2) of Item 10.2 - Disassembly of Top Cabinet
Step 1 Remove 7 screws and disconnect wire CN2810 (Fan) at rear cabinet as shown.
10.5. Disassembly of CD Mechanism Unit
· Follow the (Step 1) - (Step 2) of Item 10.2 - Disassembly of Top Cabinet Step 1 Remove one screw at rear panel.
Step 2 Detach the FFC wires (CN2801 & CN2805).
Step 4 Remove 4 screws.
Step 5 Remove the CD chassis.
Step 6 Lay the CD mechanism unit as shown.
· For disassembly of CD mechanism unit, please refer to Section 10.11 of this manual.
Step 3 Release the claws of both ends, and then lift up the CD
Mechanism Unit.
15
SA-AK330P / SA-AK330PC
10.6. Disassembly of Main P.C.B.
·Follow the (Step 1) - (Step 2) of Item 10.2 - Disassembly of Top Cabinet
·Follow the (Step 1) - (Step 6) of Item 10.3 - Disassembly of CD Lid
·Follow the (Step 1) of Item 10.4 - Disassembly of the Rear Panel
·Follow the (Step 1) - (Step 3) of Item 10.5 - Disassembly of the CD Mechanism Unit
Step 1 Disconnect FFC wires CN2803 & CN2806 from Main |
Step 2 Lift up Main P.C.B. by disconnecting connectors |
P.C.B. |
CN5800 & CN5801 as arrow shown above. |
10.7. Disassembly of Power P.C.B.
·Follow the (Step 1) - (Step 2) of Item 10.2 - Disassembly of Top Cabinet
·Follow the (Step 1) - (Step 6) of Item 10.3 - Disassembly of CD Lid
·Follow the (Step 1) of Item 10.4 - Disassembly of the Rear Panel
·Follow the (Step 1) - (Step 3) of Item 10.5 - Disassembly of the CD Mechanism Unit
·Follow the (Step 1) - (Step 2) of Item 10.6 - Disassembly of the Main P.C.B.
Step 1 Remove the 2 screws fixed at heat sink and 1 screw fixed at Power P.C.B..
Note:
Insulate the Power P.C.B. with insulation material to avoid short circuit.
16
SA-AK330P / SA-AK330PC
· Replacement of the Power Amplifier IC/ Voltage Regulator
Step 1 Remove 2 screws fixed to the Power Amplifier IC and 1 screw to Voltage Regulator.
Step 3 Unsolder the terminals of Power Amp IC, transistor and replace the components.
Step 4 Fix back the cut portion with a screw as shown.
Step 2 Break the joint with a metal cutter as shown below.
10.8. Disassembly of Transformer P.C.B.
·Follow the (Step 1) - (Step 2) of Item 10.2 - Disassembly of Top Cabinet
·Follow the (Step 1) - (Step 6) of Item 10.3 - Disassembly of CD Lid
·Follow the (Step 1) of Item 10.4 - Disassembly of the Rear Panel
·Follow the (Step 1) - (Step 3) of Item 10.5 - Disassembly of the CD Mechanism Unit Step 1 Remove 3 screws, disconnect connector CN5950.
17
SA-AK330P / SA-AK330PC
10.9. Disassembly of Front Panel Unit
·Follow the (Step 1) - (Step 2) of Item 10.2 - Disassembly of Top Cabinet
·Follow the (Step 1) - (Step 6) of Item 10.3 - Disassembly of CD Lid
·Follow the (Step 1) of Item 10.4 - Disassembly of the Rear Panel
·Follow the (Step 1) - (Step 3) of Item 10.5 - Disassembly of the CD Mechanism Unit
Step 1 Lay the unit as shown below. |
· Disassembly of Panel P.C.B. |
Step 2 Release 2 claws at bottom and 2 claws each side, draw the front panel ass’y forward.
Step 3 Remove volume knob.
Step 4 Remove the 10 screws.
Step 5 Disconnect connectors CN2806, CN2803 and CN5950.
10.10. Disassembly of Deck Mechanism Unit
·Follow the (Step 1) - (Step 2) of Item 10.2 - Disassembly of Top Cabinet
·Follow the (Step 1) - (Step 6) of Item 10.3 - Disassembly of CD Lid
·Follow the (Step 1) of Item 10.4 - Disassembly of the Rear Panel
·Follow the (Step 1) - (Step 3) of Item 10.5 - Disassembly of the CD Mechanism Unit
·Follow the (Step 1) - (Step 3) of Item 10.9 - Disassembly of the Front Panel Unit Step 1 Detach FFC wire (at CN971).
Step 2 Disconnect FFC flat cable from the connector (CN1001).
Step 3 Remove the 5 screws.
Step 4 Push the lever upward, and then open the cassette lid ass’y (For DECK1 and DECK2).
Step 5 Tilt the cassette mechanism unit in the direction of arrow (1), and then remove it in the direction of arrow (2).
· For replacement of Deck Mechanism P.C.B. Step 6 Remove 3 screws.
18
SA-AK330P / SA-AK330PC
Step 7 Unsolder the motor terminals.
Step 8 Remove Deck Mechanism P.C.B.
10.11. CD Mechanism Main Component Replacement Procedures
·Follow the (Step 1) - (Step 2) of Item 10.2 - Disassembly of Top Cabinet
·Follow the (Step 1) - (Step 6) of Item 10.3 - Disassembly of CD Lid
·Follow the (Step 1) - (Step 6) of Item 10.5 - Disassembly of the CD Mechanism Unit
10.11.1. Replacement of the Traverse Deck
Step 1 Remove the CD changer unit.
Step 2 Insert the gear with hexagonal wrench into the hole.
Step 4 With pressing the claw (A), rotate the hexagonal wrench clockwise. (The slide plate R moves for a little amount.)
Step 5 Pressing the claw (B) in the direction of arrow (1), the connection lever moves in the direction of arrow (2).
Step 3 Rotate the hexagonal wrench in the direction of arrow (clockwise), and then open the disc tray fully.
19
SA-AK330P / SA-AK330PC
Step 6 Lift up the traverse deck ass’y.
Step 7 Remove the traverse deck ass’y from the timing lever.
Caution:
When removing or inserting the traverse deck avoid touching the OPU lens and pressing onto the turntable.
Step 8 Remove 3 screws.
Step 9 Unsolder the motor terminals (4 points).
Step 10 Remove the FFC board from the connector, and then remove the CD Servo P.C.B.
Step 11 Remove the pin.
Step 12 Release the claw, and then remove the traverse deck ass’y.
20
Note:
Be careful not to lose the 3 floating spring because those will also be removed on removal of the traverse deck ass’y.
· Installation of the CD Servo P.C.B. after replacement Step 1 Connect the FFC board.
Step 2 Install the CD servo P.C.B. in the traverse deck ass’y. Step 3 Remove 3 screws.
Step 4 Solder.
· Note for installation of the CD servo P.C.B.
· Installation for traverse deck ass’y
SA-AK330P / SA-AK330PC
Step 1 Install the traverse deck ass’y to the timing lever.
Step 2 Align the boss of traverse deck ass’y with the slot of traverse cam gear.
Step 3 Force the claw of timing lever.
Step 4 Force the disc tray fully.
21
SA-AK330P / SA-AK330PC
Step 5 With pressing the claw (B) in the direction of arrow (1), force the connection lever in the direction of arrow (2).
10.11.2. Replacement for the Disc Tray
Step 1 Remove 4 screws.
Step 2 Remove the upper plate.
Step 3 Remove 3 screws.
Step 4 With lifting the claw in the direction of (1), draw the CD Detect P.C.B. in the direction of arrow (2).
Step 5 Remove the mechanism cover.
Step 6 Insert the gear with hexagonal wrench into the hole.
Step 7 Rotate the hexagonal wrench in the direction of arrow, and then open the disc tray fully.
22
SA-AK330P / SA-AK330PC
Step 8 Release the both claws, and then draw the disc tray.
Step 9 With forcing the left guide bar manually because the left guide bar interfers with claw, draw the disc tray.
[Installation of the disc tray after replacement]
Step 1 Slide the drive rack fully in the direction of arrow.
Step 2 Holding the drive rack not to move, install the disc tray. Step 3 Align the drive rack with the drive gear.
NOTE:
Force the right guide bar of tray base manually not to move upwards.
Step 4 Holding the disc tray manually, push the disc tray in the direction of the arrow.
23
SA-AK330P / SA-AK330PC
10.11.3. Disassembly and reassembly for mechanism base drive unit
Step 1 Remove 3 screws.
Step 2 Release the claw, and then remove the gear holder.
Step 3 Remove the belt and change gear spring.
NOTE:
Take care not to lose the change gear spring.
Step 4 Remove the pulley gear, change gear and UP/DOWN gear.
Step 6 Install the tray lock spring to hook temporary. Step 7 Release the claw, and then remove the tray lock. Step 8 Release the claw, and then remove the rear lock.
Step 5 Release the 2 claws, and then remove the bottom SW P.C.B..
24
SA-AK330P / SA-AK330PC
Step 9 Pressing the claw (B) in the direction of arrow (1), force the connection lever in the direction of arrow (2).
Step 10 Move the slide plate 1 to the end of stock side.
Step 11 Lift up the left end of spindle base unit in the direction of arrow (1), and then remove the unit in the direction of arrow
(2).
Step 12 Remove slide plate 1 and slide plate 2.
25
SA-AK330P / SA-AK330PC
Step 13 Remove the traverse relay gear, traverse cam gear and drive gear.
[Dissassembly/reassembly for the spindle base unit] Step 1 Draw the 5 disc spacers.
Step 2 Pushing the claw, slide the support plate in the direction of arrow, and then remove it.
Step 3 Rotate the disc lever in the direction of arrow (1), draw the disc lever.
NOTE:
Take care not to lose the disc lever spring.
Step 4 Release the 2 claws, and then draw the relay gear B. Step 5 Release the 2 claws as shown below.
26
SA-AK330P / SA-AK330PC
NOTE:
Hold the loading stopper ass’y manually bacause it is flipped by spring.
Step 6 Remove the cushion spring.
Step 7 Remove the loading stopper ass’y in the direction of arrow.
Step 8 Release the 2 claws, and then remove the relay gear A. Step 9 Release the 2 claws, and then remove the spindle shaft.
Step 10 Remove the lower spindle spring with tweezers. Step 11 Force the lower hook with thin tip of minus screwdriver.
27
SA-AK330P / SA-AK330PC
Step 12 Squeeze the shaft of lower hook, and then draw it.
Step 13 Rotate the lower spindle in the direction of arrow until the lower spindle interferes with stopper.
Step 14 Insert the thin tip of minus screwdriver between the lower spindle and UP/DOWN base, and then slacken the lower spindle to release the stopper. Then, rotate the lower spindle and remove it.
Step 15 Rotate the UP/DOWN base at a 90° angle. Then,
spread the hold bars of loading stopper and remove the UP/DOWN base.
[Installation for loading stopper ass’y]
Step 1 Align the claw of loading stoppers ass’y with the slot of spindle base. (Caution should be exercised when alignment of claw due to the size of claws.)
Step 2 Lower the loading stopper ass’y, and then align the lower spindle with the trapezoid tooth of relay gear A.
Step 3 Force the loading stopper ass’y, latch the claw firmly.
[Reassembly for mechanism base drive unit]
28
Step 1 Install the traverse cam gear.
Step 2 Rotate the traverse cam gear to the direction of arrow.
Step 3 Install the drive gear and traverse relay gear.
*When installing the traverse relay gear, align the trapezoid tooth of gear with tooth of traverse cam gear.
SA-AK330P / SA-AK330PC
Step 4 Install the slide plate 2 to the mechanism base, and then match to the connection lever.
Step 5 Install the slide plate 1 to the mechanism base, and then match to the connection leve and align the trapezoid tooth of traverse relay gear with the slide plate 1.
Step 6 Install the spindle base unit. (First, slide plate 1.)
29
SA-AK330P / SA-AK330PC
Step 7 Move the slide plate 1 to forward fully.
Step 8 Install the rear lock. (The claw should be latched.)
Step 9 Install the Spindle Position P.C.B.. (The claw should be latched.)
Step 10 Install the tray lock. (The claw should be latched.)
Step 11 Remove the tray lock spring from hook,and then latch to the tray lock.
Step 12 Install the UP/DOWN gear, change gear, change gear spring, pulley gear and belt in the order of (1) - (5).
Step 13 Install the gear holder, and then tighten the screw (a).
30
Loading...