Onkyo HT-R430, HT-S680 Instruction Manual

6.1ch Home Theater System

HT-S680

AV Receiver (HT-R430)

Front Speakers (SKF-330F L/R)

Center Speaker (SKC-330C)

Surround Speakers (SKM-330S L/R)

Surround Back Speaker (SKB-330)

Powered Subwoofer (SKW-420)

Instruction Manual

Thank you for purchasing an Onkyo 6.1ch Home Theater System. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new 6.1ch Home Theater System.

Please retain this manual for future reference.

Contents

Introduction .....................................

2

Connection ....................................

17

Turning On & First Time Setup..... 32

Basic Operation
Playing your AV components .......	34
Using the Tuner............................	36

Enjoying the Listening Modes ..... 40

Advanced Operation .....................	44
Troubleshooting ............................	52
Specification..................................	54

En

PORTABLE CART WARNING

S3125A

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING		AVIS
RISK OF ELECTRIC SHOCK		RISQUE DE CHOC ELECTRIQUE
DO NOT OPEN		NE PAS OUVRIR

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Important Safety Instructions

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15.Damage Requiring Service

Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions:

A.When the power-supply cord or plug is damaged,

B.If liquid has been spilled, or objects have fallen into the apparatus,

C.If the apparatus has been exposed to rain or water,

D.If the apparatus does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation,

E.If the apparatus has been dropped or damaged in any way, and

F.When the apparatus exhibits a distinct change in performance this indicates a need for service.

16.Object and Liquid Entry

Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock.

The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus.

Don’t put candles or other burning objects on top of this unit.

17.Batteries

Always consider the environmental issues and follow local regulations when disposing of batteries.

18.If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation.

Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue-like gap for warm air to escape.

2

Precautions

1.Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder.

2.AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your Onkyo dealer.

3.Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering.

4.Power WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY.

AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

Some models have a voltage selector switch for compatibility with power systems around the world. Before you plug in such a model, make sure that the voltage selector is set to the correct voltage for your area.

Setting the [STANDBY/ON] switch to STANDBY does not fully shutdown the unit. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5.Never Touch this Unit with Wet Hands—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer.

6.Handling Notes

•If you need to transport this unit, use the original packaging to pack it how it was when you originally bought it.

•Do not leave rubber or plastic items on this unit for a long time, because they may leave marks on the case.

•This unit’s top and rear panels may get warm after prolonged use. This is normal.

•If you do not use this unit for a long time, it may not work properly the next time you turn it on, so be sure to use it occasionally.

Memory Backup

The AV receiver uses a battery-less memory backup system in order to retain radio presets and other settings when it’s unplugged or in the case of a power failure. Although no batteries are required, the AV receiver must be plugged into an AC outlet in order to charge the backup system. Once it has been charged, the AV receiver will retain the settings for several weeks, although this depends on the environment and will be shorter in humid climates.

For U.S. models

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

For models having a power cord with a polarized plug: CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modèle canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA.

Sur les modèles dont la fiche est polarisée: ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

3

Speaker Precautions

Placement

•The subwoofer cabinet is made out of wood and is therefore sensitive to extreme temperatures and humidity, do not put it in locations subject to direct sunlight or in humid places, such as near an air conditioner, humidifier, bathroom, or kitchen.

•Do not put water or other liquids close to the speakers. If liquid is spilled over the speakers, the drive units may be damaged.

•Speakers should only be placed on sturdy, flat surfaces that are free from vibration. Putting them on uneven or unstable surfaces, where they may fall and cause damage, will affect the sound quality.

•Subwoofer is designed to be used in the upright vertical position only. Do not use it in the horizontal or tilted position.

•If the unit is used near a turntable or CD player, howling or slipping of sound may occur. To prevent this, move the unit away from the turntable or CD player otherwise lower the unit’s output level.

Using Close to a TV or Computer

TVs and computer monitors are magnetically sensitive devices and as such are likely to suffer discoloration or picture distortion when conventional speakers are placed nearby. To prevent this, the SKF-330F and SKC-330C feature internal magnetic shielding. In some situations, however, discoloration may still be an issue, in which case you should turn off your TV or monitor, wait 15 to 30 minutes, and then turn it back on again. This normally activates the degaussing function, which neutralizes the magnetic field, thereby removing any discoloration effects. If discoloration problems persist, try moving the speakers away from your TV or monitor. Note that discoloration can also be caused by a magnet or demagnetizing tool that’s too close to your TV or monitor.

Do not place SKM-330 and SKB-330 close to TV or a computer monitor because they have no magnetic shield.

Input Signal Warning

The speakers can handle the specified input power when used for normal music reproduction. If any of the following signals are fed to them, even if the input power is within the specified rating, excessive current may flow in the speaker coils, causing burning or wire breakage:

1.Interstation noise from an untuned FM radio.

2.Sound from fast-forwarding a cassette tape.

3.High-pitched sounds generated by an oscillator, electronic musical instrument, and so on.

4.Amplifier oscillation.

5.Special test tones from audio test CDs and so on.

6.Thumps and clicks caused by connecting or disconnecting audio cables (Always turn off your amplifier before connecting or disconnecting cables.)

7.Microphone feedback.

Features

Amp

•6-channel amplifier

•100 watts per channel min. RMS at 8 Ω, 2 channels driven from 1 kHz with no more than 0.9% total harmonic distortion

•WRAT (Wide Range Amplifier Technology)

•Optimum gain volume circuitry

•OptiResponse™ Equalizer (OR-EQ™)*1 function

Processing

•Dolby*2 Digital EX and Dolby Pro Logic IIx

•DTS, DTS-ES Matrix/Discrete, and DTS Neo:6 processing*3

•Cinema Filter function

•Linear PCM 192 kHz/24-bit D/A converters on all channels

•Powerful and highly accurate 32-bit DSP Processing

Audio/Video

•Adjustable crossover (60, 80, 100, 120, 150 Hz)

•3 S-Video inputs, 2 outputs

•2 assignable digital inputs (1 optical, 1 coaxial)

•Subwoofer pre out

•Color-coded multichannel input for use with Super Audio CD and DVD-Audio

•A/B speaker drive

•Color-coded speaker terminal

FM/AM Tuner

•30 FM/AM presets

•FM/AM auto tuning

•RDS (Radio Data System) (Europe only)

Remote Controller

•Remote controller can be used to control Onkyo CD, CDR, MD components, and cassette tape deck

Front / Center / Surround Speakers

•Color-coded speaker terminals and speaker cables

•3-1/8" (8 cm) cone woofer

•Ceramic tweeter

Subwoofer

•Built-in 150 watts power amplifier

•8" cone woofer

•Auto Standby/On

*1. OptiResponse and OR-EQ are trademarks of Onkyo Corporation.

*2. Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are registered trademarks of Dolby Laboratories.

*3. “DTS” and “Neo:6” are trademarks of Digital Theater Systems, Inc.

4

Table of Contents

Introduction
Important Safety Instructions .....................		2
Precautions ..................................................		3
Speaker Precautions ...................................		4
Features ........................................................		4
Supplied Accessories..................................		6
Before Using the AV receiver .....................		7
Front & Rear Panels.....................................		8
Speaker Package .......................................		11
Remote Controller......................................		12
Connection
Connecting Speakers ................................		17
Enjoying Home Theater................................		17
Speaker Connection Precautions.................		18
Connecting Speaker.....................................		18
Wall Mounting...............................................		19
Using Speaker Mounts/Brackets ..................		19
Using Rubber Stoppers
with the Speakers ......................................		19
Connecting Antenna..................................		20
Connecting the Indoor FM Antenna .............		20
Connecting the AM Loop Antenna ...............		20
Connecting an Outdoor FM Antenna............		21
Connecting an Outdoor AM Antenna ...........		21
Connecting Your Components .................		22
About AV Connections .................................		22
Connecting Both Audio & Video ...................		23
Which Connections Should I Use?...............		23
Connecting a TV or Projector .......................		24
Connecting a DVD player.............................		25
Connecting a VCR or DVD Recorder
for Playback ...............................................		26
Connecting a VCR or DVD Recorder
for Recording .............................................		27
Connecting a Camcorder, Games
Console, or Other Device...........................		27
Connecting a Satellite, Cable,
Set-top box, or Other Video Source...........		28
Connecting a CD Player or Turntable ..........		29
Connecting a Cassette, CDR, MiniDisc,
or DAT Recorder........................................		30
Connecting the Power Cord of
Another Component...................................		30
Connecting Onkyo	Components ...........	31
Connecting the Power Cord .........................		31
Turning On & First Time Setup
Turning On..................................................		32
Turning On the AV Receiver ........................		32
First Time Setup.........................................		33
Assigning Digital Inputs to Input Sources .....		33
Changing the TAPE/MD/CDR Display .........		33

Basic Operation
Playing Your AV Components .................	34
Basic AV Receiver Operation .......................	34
Using the Multichannel Input ........................	35
Displaying Source Information......................	35
Using the Tuner .........................................	36
Listening to the Radio ...................................	36
Tuning into Radio Stations ...........................	36
Common Functions...................................	38
Using the OptiResponse Equalizer...............	38
Setting the Display Brightness......................	38
Adjusting the Bass & Treble .........................	38
Muting the AV Receiver ................................	38
Using the Sleep Timer ..................................	39
Using Headphones .......................................	39
Adjusting Speaker Levels .............................	39
Enjoying the Listening Modes
Using the Listening Modes.......................	40
Selecting Listening Modes............................	40
Advanced Operation
Adjusting the Listening Modes ................	44
Using the Audio Adjust Functions.................	44
Using the Late Night Function
(Dolby Digital only) .....................................	45
Using the CinemaFILTER.............................	45
Advanced Setup ........................................	46
Advanced Speaker Settings .........................	46
Digital Input Signal Formats .........................	50
Recording...................................................	51
Recording the Input Source ..........................	51
Recording from Different AV Sources ..........	51
Troubleshooting ........................................	52
Power ...........................................................	52
Audio ............................................................	52
Video ............................................................	53
Tuner ............................................................	53
Remote Controller ........................................	53
Recording .....................................................	54
Others ...........................................................	54
Specification ..............................................	54

5

Supplied Accessories

Make sure you have the following accessories:

HT-R430

HT-R430

Remote controller & two batteries (AA/R6)

Indoor FM antenna

(Connector type varies from country to country.)

AM loop antenna

Power-plug adapter

Only supplied in certain countries. Use this adapter if your AC outlet does not match with the plug on the AV receiver’s power cord. (Adapter varies from country to country.)

HTP-430

Front speakers (SKF-330F L/R)

Center speaker (SKC-330C)

Surround speakers (SKM-330S L/R)

Surround Back speaker (SKB-330)

Subwoofer (SKW-420)

(Red) (White)

Speaker cable for front speakers 15 ft. (4.5 m)

(Green)

Speaker cable for center speaker 10 ft. (3 m)

(Blue)

(Gray)

(Brown)

Speaker cables for surround speakers 30 ft. (9 m)

RCA cable for subwoofer connection

Rubber stoppers [24]

*In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operation are the same regardless of color.

6

Before Using the AV receiver

Installing the Batteries

1 To open the battery compartment, press the small hollow and slide open the cover.

2 Insert the two supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment.

3 Slide the cover shut.

Notes:

•The batteries should last for about six months, although this will vary with usage.

•If the remote controller doesn’t work reliably, try replacing the batteries.

•Don’t mix new and old batteries or different types of batteries.

•If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

•Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion.

Using the Remote Controller

To use the remote controller, point it at the AV receiver’s remote control sensor, as shown below.

Remote control sensor

AV receiver

STANDBY indicator

Approx. 16 ft. (5 m)

Notes:

•The remote controller may not work reliably if the AV receiver is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. Keep this in mind when installing.

•If another remote controller of the same type is used in the same room, or the AV receiver is installed close to equipment that uses infrared rays, the remote controller may not work reliably.

•Don’t put anything, such as a book, on the remote controller, because the buttons may be pressed inadvertently, thereby draining the batteries.

•The remote controller may not work reliably if the AV receiver is installed in a rack behind colored glass doors. Keep this in mind when installing.

•The remote controller will not work if there’s an obstacle between it and the AV receiver’s remote control sensor.

7

Front & Rear Panels

Front Panel

1

2

3

4 5 6 78 9JK

L

M

TUNING

/ PRESET

MASTER VOLUME

STANDBY/ON

ENTER

STANDBY

A

SPEAKERS B

TONE

+

STEREO

LISTENING MODE

DISPLAY DIGITAL INPUT

DIMMER

MEMORY TUNING MODE

RETURN

SETUP

CLEAR

PHONES

MULTl CH

DVD

VIDEO 1/VCR

VIDEO 2

VIDEO 3

TAPE

TUNER

CD

N O

P

Q

R

S

For detailed information, see the pages in parentheses.

ASTANDBY/ON button (32)

This button is used to set the AV receiver to On or Standby.

BSTANDBY indicator (32)

This indicator lights up when the AV receiver is in Standby mode, and it flashes while a signal is being received from the remote controller.

CRemote-control sensor (7)

This sensor receives control signals from the remote controller.

DSTEREO button (40)

This button is used to select the Stereo listening mode.

ELISTENING MODE []/[] buttons (40)

These buttons are used to select the listening modes.

FDisplay

See “Display” on page 9.

GDISPLAY button (35)

This button is used to display various information about the currently selected input source.

HDIGITAL INPUT button (33)

This button is used to assign the digital inputs and to specify the format of digital input signals.

IDIMMER button (38)

This button is used to adjust the display brightness.

JMEMORY button (37)

This button is used when storing or deleting radio presets.

KTUNING MODE button (36)

This button is used to select the Auto or Manual tuning mode.

LArrow/TUNING/PRESET & ENTER buttons

When the AM or FM input source is selected, the

TUNING [] [] buttons are used to tune the tuner, and the PRESET [] [] buttons are used to select radio presets (see page 37). When the setup menus are used, they work as arrow buttons and are used to select and set items. The ENTER button is also used with the setup menus.

MMASTER VOLUME control (34)

This control is used to adjust the volume of the AV receiver to MIN, 1 through 79, or MAX

NPHONES jack (39)

This 1/4-inch phone jack is for connecting a standard pair of stereo headphones for private listening.

OSPEAKER A & B buttons (34)

These buttons are used to turn speaker sets A and B on or off.

PTONE, [–] & [+] buttons (38)

These buttons are used to adjust the bass and treble.

QInput selector buttons (34)

These buttons are used to select from the following input sources: MULTI CH, DVD, VIDEO 1/VCR, VIDEO 2, VIDEO 3, TAPE, TUNER, or CD.

The [MULTI CH] button selects the DVD analog multichannel input.

RRETURN button

This button is used to return to the previously displayed setup menu.

SSETUP button

This button is used to access various settings.

8

Front & Rear Panels—Continued

Display

1	2		3			4

5

6

For detailed information, see the pages in parentheses.

1A & B speaker indicators (34)

Indicator A lights up when speaker set A is on. Indicator B lights up when speaker set B is on.

2MUTING indicator (38)

This indicator flashes when the AV receiver is muted.

3 Source/listening mode indicators (42)

5SLEEP indicator (39)

This indicator lights up when the Sleep function has been set.

6Message area

This area of the display shows various information about the currently selected source.

These indicators show the currently selected listening mode and digital audio format.

4Tuning indicators (36)

TUNED (36): This indicator lights up when the AV receiver is tuned to a radio station.

AUTO (36): This indicator lights up when Auto Tuning is selected and disappears when Manual Tuning is selected.

MEMORY (37): This indicator lights up when presetting radio stations.

FM STEREO (36): This indicator lights up when the AV receiver is tuned to a stereo FM station.

9

Front & Rear Panels—Continued

Rear Panel

1	B 3		4	5	6
7 8 9 J K		L	M	N	O

ADIGITAL IN OPTICAL & COAXIAL

These optical and coaxial jacks can be used to connect a CD or DVD player and other components with digital audio outputs.

BAM ANTENNA

These push terminals are for connecting an AM antenna.

CFM ANTENNA

This jack is for connecting an FM antenna.

DVIDEO MONITOR OUT

This composite video jack can be connected to a composite video input on your TV or projector.

EFRONT SPEAKERS B

These push terminals are for connecting speaker set B.

FFRONT SPEAKERS A, SURROUND SPEAKERS, CENTER SPEAKER & SURROUND BACK SPEAKER

These push terminals are for connecting speaker set A.

G

This (Remote Interactive) jack can be connected to the jack on another Onkyo component. The AV receiver’s remote controller can then be used to control that component. To use , you must make an analog audio connection (RCA) between the AV receiver and the other component, even if they are connected digitally.

Note:

can only be used with Onkyo components.

HS VIDEO DVD IN,VIDEO 1 IN/OUT &VIDEO 2 IN

The DVD IN jack can be connected to an S-Video output on a DVD player. The VIDEO 1 IN/OUT

jacks can be used to connect a VCR. The VIDEO 2 IN jack can be used to connect another video source (e.g., cable TV, satellite TV, or a set-top-box).

ICD IN

These analog inputs can be used to connect a CD player with analog outputs.

JTAPE IN/OUT

These analog inputs and outputs can be used to connect a cassette recorder, MiniDisc recorder, or other recorder with analog inputs and outputs.

KS VIDEO MONITOR OUT

This S-Video jack can be connected to an S-Video input on your TV or projector.

LVIDEO 1 IN/OUT, VIDEO 2 IN & VIDEO 3 IN

The VIDEO 1 IN/OUT jacks can be used to connect a VCR. The VIDEO 2 IN and VIDEO 3 IN jacks can be used to connect other video sources (e.g., cable TV, satellite TV, or a set-top-box).

MDVD IN

The FRONT, SURROUND, CENTER, and SUBWOOFER jacks can be used to connect a component with an analog multichannel audio output, such as a DVD player with a 5.1-channel analog output. The composite video input can be connected to the composite video output on a DVD player.

NSUBWOOFER PRE OUT

A powered subwoofer can be connected here.

OAC OUTLET

This switched AC outlet can be used to supply power to another component. The connector type depends on the country in which you purchased your AV receiver.

See pages 17–31 for connection information.

10

Speaker Package

Front, Center, Surround, & Subwoofer speakers (SKF-330F, SKC-330C, SKM-330S, SKB-330, SKW-420)

■ Rear			A Speaker terminals
			These push terminals are for connecting the speaker
SKF-330F			to the HT-R430 with the supplied speaker cables.
SKM-330S			The supplied speaker cables are color-coded for
SKB-330			easy identification. Simply connect each cable to the
			same-colored positive speaker terminal.
2			B Keyhole slots
			These keyhole slots can be used to wall-mount the
			speaker. See page 19 for mounting instructions.
			C Speaker mount/bracket inserts
			These threaded inserts can be used to attach the
			speaker to a speaker mount or bracket. See page 19
			for mounting instructions.
			Note:
3	1		Use commercially available machine screws to
			attach the speaker to a speaker mount or bracket.
			North American models require 1/4-inch screws.
2		2	Other models require M5 (5 mm) screws.
			D OUTPUT LEVEL control
SKC-330C
			This control is used to adjust the volume of the sub-
			woofer.
			E STANDBY/ON indicator
			Red:	Subwoofer in standby mode
			Green:	Subwoofer on

With the Auto Standby function, the SKW-420 automatically turns on when an input signal is detected in Standby mode. When there’s no input

3 1 signal for about 20 minutes, the SKW-420 automatically enters Standby mode.

SKW-420

OUTPUT		LINE
LEVEL		INPUT
MIN	MAX
RED : STANDBY
GREEN : ON

4 5

6 7

					F POWER switch (Not North American model)
					To turn on the SKW-420, set the POWER switch to
					the ON position (the indicator light up).
					To turn off the SKW-420, set the POWER switch to
					the OFF position (the indicator goes out).
					G LINE INPUT
					This RCA input should be connected to the SUB-
					WOOFER PREOUT on your HT-R430 AV receiver,
					amp, or other receiver with supplied RCA cable.
					Note:
					The Auto Standby function turns the subwoofer on when
					the input signal exceeds a certain level. If the Auto
					Standby function does not work reliably, try slightly
	To AC outlet
					increasing or decreasing the subwoofer output level on
					your receiver or amp (see page 47).

11

Remote Controller

How to Use the Remote Controller

Including the AV receiver, the remote controller can be used to control up to six different components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the five REMOTE MODE buttons.

■ RECEIVER/TAPE Mode

In RECEIVER/TAPE mode, you can control the AV receiver and an Onkyo cassette recorder connected via .

■ DVD, CD, MD, & CDR Modes
With these modes, you can control an		DVD
Onkyo DVD player and CD/MD/CDR
player/recorder.		CD
		MD
		CDR
1	Use the REMOTE MODE buttons to select
	a mode.
2	Use the buttons supported by that mode

to control the component.

RECEIVER mode: see page 12 DVD mode: see page 14 CD/MD/CDR mode: see page 15 TAPE mode: see page 16

Note:

Some of the remote controller operations described in this manual may not work as expected with other components.

RECEIVER Mode

RECEIVER mode is used to control the AV receiver.

To set the remote controller to RECEIVER mode, press the [RECEIVER] REMOTE MODE button.

A					RECEIVER
	ON	STANDBY	REMOTE MODE
B			RECEIVER	DVD
			TAPE/AMP
	INPUT SELECTOR
C	1	2	3	CD
	V1	V2	V3
D	4	5	6	MD	M
		MULTI CH	DVD
	7	8	9	CDR
	TAPE	TUNER	CD

E	+10	0 CLR		N
	--/---	DIMMER SLEEP
F		DISC		O
		CH	VOL
	TOP MENU		MENU
G				P
	SP A / B		MUTING
H		ENTER
I				Q
	RETURN		SETUP

J		LISTENING MODE
	STEREO	SURROUND
K	AUDIO	SUBTITLE RANDOM		REPEAT
	TEST TONE	CH SEL	LEVEL-	LEVEL+
L		PLAY MODE			R
	DISPLAY	OR-EQ	L NIGHT	CINE FLTR

S

T

RC-606S

12

Remote Controller—Continued

For detailed information, see the pages in parentheses.

ASTANDBY button (32)

This button is used to set the AV receiver to Standby.

BON button (32)

This button is used to turn on the AV receiver.

CINPUT SELECTOR buttons (34)

These buttons are used to select the input sources.

DMULTI CH button (35)

This button is used to select the multichannel DVD input.

EDIMMER button (38)

This button is used to adjust the display brightness.

FCH +/– button (37)

This button is used to select radio presets.

GSP A/B button (34)

This button is used to turn speaker sets A and B on or off.

HArrow []/[]/[]/[] & ENTER buttons

These buttons are used to select and adjust settings.

IRETURN button

This button is used to return to the previous display when changing settings.

JLISTENING MODE buttons (40)

These buttons can be used to select listening modes regardless of the currently selected remote controller mode.

STEREO button

This button selects the Stereo listening mode.

SURROUND button

This button selects the Dolby and DTS listening modes.

[]/[] buttons

These buttons can be used to select any of the available listening modes.

KTEST TONE, CH SEL, LEVEL- & LEVEL+ buttons (32)

These buttons are used to adjust the level of each speaker.

LDISPLAY button (35)

This button is used to display various information about the currently selected input source.

MREMOTE MODE buttons (12)

These buttons are used to select the remote controller modes. When you press a button on the remote controller, the REMOTE MODE button for the currently selected mode lights up.

NSLEEP button (39)

This button is used to set the Sleep function.

OVOL []/[] button (34)

This button can be used to adjust the volume of the AV receiver regardless of the currently selected remote controller mode.

PMUTING button (38)

This button is used to mute the AV receiver.

QSETUP button

This button is used to access various settings.

RCINE FLTR button (45)

This button is used to set the CinemaFILTER function.

SL NIGHT button (45)

This button is used to set the Late Night function.

TOR-EQ button (38)

This button is used to turn on the OptiResponse equalizer, which optimizes performance when the HT-R430 is used with the speakers included in the HTP-430 Home Theater Speaker Package. When the OptiResponse equalizer is on, you can enjoy a powerful sound with movies or music with small volume.

13

Remote Controller—Continued

DVD Mode

To set the remote controller to DVD mode, press the [DVD] REMOTE MODE button.

Before selecting DVD mode and starting playback, you should press the [RECEIVER] mode button followed by the [DVD] INPUT SELECTOR button to select the DVD player as the input source.

A

ON STANDBY

REMOTE MODE

B			RECEIVER	DVD	DVD
			TAPE/AMP
	INPUT SELECTOR
C	1	2	3	CD
	V1	V2	V3
	4	5	6	MD
	MULTI CH		DVD
	7	8	9	CDR
	TAPE	TUNER	CD
	+10	0	CLR		L
	--/---	DIMMER	SLEEP
D			CH	VOL
			DISC
	TOP MENU			MENU
E	SP A / B			MUTING	M
F		ENTER

GN

RETURN	SETUP
H

			LISTENING MODE
	I	STEREO	SURROUND			O
		AUDIO	SUBTITLE RANDOM		REPEAT
	J					P
		TEST TONE	CH SEL	LEVEL-	LEVEL+
	K		PLAY MODE
		DISPLAY	OR-EQ	L NIGHT	CINE FLTR

Q

RC-606S

ASTANDBY button

This button sets the DVD player to Standby.

BON button

This button is used to turn on the DVD player.

CNumber buttons

These buttons are used to enter title, chapter, and track numbers and to enter times for locating specific points in time.

DDISC +/– button

This button selects discs on a DVD changer.

ETOP MENU button

This button is used to select a DVD’s top menu.

FArrow []/[]/[]/[] & ENTER buttons

These buttons are used to navigate DVD menus and the DVD player’s onscreen setup menus.

GRETURN button

This button is used to exit the DVD player’s onscreen setup menu and to restart menu playback.

HPlayback buttons

From left to right: Pause, Play, Stop, Fast Reverse, Fast Forward, Previous, and Next.

ISUBTITLE button

This button is used to select subtitles.

JAUDIO button

This button selects foreign language soundtracks and audio formats (e.g., Dolby Digital or DTS).

KDISPLAY button

This button is used to display information about the current disc, title, chapter, or track on the DVD player’s display, including the elapsed time, remaining time, total time, and so on.

LCLR button

This button is used to cancel functions and to clear entered numbers.

MMENU button

This button is used to display a DVD’s menu.

NSETUP button

This button is used to access the DVD player’s onscreen setup menus.

ORANDOM button

This button is used with the random playback function.

PREPEAT button

This button is used to set the repeat playback functions.

QPLAY MODE button

This button is used to select play modes on a component with selectable play modes.

14

Remote Controller—Continued

CD, MD, & CDR Mode

To set the remote controller to CD, MD, or CDR mode, press the [CD], [MD], or [CDR] REMOTE MODE button.

Before selecting a mode and starting playback, you should press the [RECEIVER] mode button followed by the [CD] or [TAPE] INPUT SELECTOR button to select the CD player, MiniDisc, or CD recorder as the input source.

A

	ON	STANDBY	REMOTE MODE
B			RECEIVER	DVD
			TAPE/AMP
	INPUT SELECTOR				CD
C	1	2	3	CD
	V1	V2	V3		MD
	4	5	6	MD
		MULTI CH	DVD		CDR
	7	8	9	CDR
	TAPE	TUNER	CD
	+10	0	CLR		G
	--/---	DIMMER	SLEEP
D			CH	VOL
			DISC
	TOP MENU			MENU
	SP A / B			MUTING
		ENTER

RETURN	SETUP
E

		LISTENING MODE
	STEREO	SURROUND			8
	AUDIO	SUBTITLE RANDOM		REPEAT
					9
	TEST TONE	CH SEL	LEVEL-	LEVEL+
F		PLAY MODE
	DISPLAY	OR-EQ	L NIGHT	CINE FLTR

J

RC-606S

ASTANDBY button

This button sets the CD player or MD/CD recorder to Standby.

BON button

This button is used to set the CD player or MD/CD recorder to On or Standby.

CNumber buttons

These buttons are used to enter track numbers and to enter times for locating specific points in time.

DDISC +/– button

This button selects discs on a CD changer.

EPlayback buttons

From left to right: Pause, Play, Stop, Fast Reverse, Fast Forward, Previous and Next.

FDISPLAY button

This button is used to display information about the current disc or track on the CD player or MD/CD recorder’s display, including the elapsed time, remaining time, total time, and so on.

GCLR button

This button is used to cancel functions and to clear entered numbers.

HRANDOM button

This button is used with the random playback function.

IREPEAT button

This button is used to set the repeat playback functions.

JPLAY MODE button

This button is used to select play modes on a component with selectable play modes.

15

Remote Controller—Continued

TAPE Mode

TAPE mode is used to control an Onkyo cassette recorder connected to the AV receiver via .

To set the remote controller to TAPE mode, press the [RECEIVER] REMOTE MODE button.

Before selecting TAPE mode and starting playback, you should press the [RECEIVER] REMOTE MODE button followed by the [TAPE] INPUT SELECTOR button to select your cassette recorder as the input source.

For twin cassette decks, only deck B can be controlled.

ON	STANDBY	REMOTE MODE		RECEIVER
		RECEIVER	DVD
		TAPE/AMP
INPUT SELECTOR
1	2	3	CD
V1	V2	V3
4	5	6	MD
	MULTI CH	DVD
7	8	9	CDR
TAPE	TUNER	CD
+10	0	CLR
--/---	DIMMER	SLEEP
		CH	VOL
		DISC
TOP MENU			MENU
SP A / B			MUTING
	ENTER
RETURN			SETUP	A
				B
				C
	LISTENING MODE			D
STEREO	SURROUND
AUDIO	SUBTITLE RANDOM		REPEAT
TEST TONE	CH SEL	LEVEL-	LEVEL+
	PLAY MODE
DISPLAY	OR-EQ	L NIGHT	CINE FLTR

RC-606S

APlay [] button

This button is used to start playback.

BStop [] button

This button is used to stop playback.

CReverse Play [] button

This button is used to start reverse playback.

DRewind & FF [ ]/[] buttons

The Rewind [ ] button is used to start rewind. The FF [] button is used to start fast forward.

16

Connecting Speakers

Enjoying Home Theater

You can use two sets of speakers with the AV receiver: speaker set A and speaker set B.

Speaker set A should be installed in your main listening room and can be used with Dolby Digital and DTS surround material. Each speaker must be positioned at a specific location in your listening room to get the best from surround sound material. The following illustration shows the best positions for your surround-sound speakers. When speaker set B is turned on, speaker set A is reduced to 2.1-channel playback. If the multichannel DVD input is selected, and speaker set B is turned on, speaker set A is reduced to 2-channel playback.

Speaker set B can be installed in another room. Speakers can be positioned in the standard position for stereo speakers or however you like.

Front left and right speakers (SKF-330F L/R)

These output the overall sound. Their role in a home theater is to provide a solid anchor for the sound image. They should be positioned facing the listener at about ear level, and equidistant from the TV. Angle them inward so as to create a triangle, with the listener at the apex.

		Surround back speaker
		(SKB-330)
		This speaker further enhances
		the realism of surround sound
		and improves sound localiza-
		tion behind the listener. It’s
	Center speaker (SKC-330C)	essential to enjoy certain lis-
		tening modes (i.e., Dolby Digi-
	This speaker enhances the front left
		tal EX and DTS-ES). Position
	and right speakers, making sound
		it behind the listener about 2–
	movements distinct and providing a
		3 feet (60–100 cm) above ear
	full sound image. In movies it’s used
		level. Make sure that the lis-
	mainly for dialog.
		tening position is within the
	Position it close to your TV (preferably
		range of the speaker.
	on top) facing forward at about ear
	level, or at the same height as the
	front left and right speakers.

Subwoofer (SKW-420)
The subwoofer handles the bass sounds of
the LFE (Low-Frequency Effects) channel.
The volume and quality of the bass output
from your subwoofer will depend on its posi-
tion, the shape of your listening room, and
your listening position. In general, a good
bass sound can be obtained by		Surround left and right speakers
installing the subwoofer in a		(SKM-330S L/R)
front corner, or at one-third		These speakers are used for precise sound
the width of the wall, as		positioning and to add realistic ambience.
shown.		Position them at the sides of the listener, or
	Corner	slightly behind, about 2–3 feet (60–100 cm)
		above ear level. Ideally they should be equi-
		distant from the listener.

1/3 wall length

To get the very best from your surround-sound system, you should also specify the distance between the listener and each individual speaker so that the sound from each speaker arrives at the listener’s ears at the same time (see page 46). In addition, you should set the level of each individual speaker to achieve an equal balance (see page 47.)

17