Jvc KD-X320BTS User Manual

KD-X320BTS
ENGLISH
FRANÇAIS
ESPAÑOL
DIGITAL MEDIA RECEIVER

INSTRUCTION MANUAL

RÉCEPTEUR MULTIMÉDIA NUMÉRIQUE
RECEPTOR DE MEDIOS DIGITALES
MANUAL DE INSTRUCCIONES
Please read all instructions carefully before operation to obtain the best possible performance from the unit.
Veuillez lires les instructions attentivement avant d’utiliser l’appareil afin d’obtenir les meilleures performances possibles de l’appareil.
Por favor lea detenidamente este manual para comprender a fondo todas las instrucciones y obtener un máximo disfrute de esta unidad.
For customer Use:
Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference. Model No. Serial No.
B5A-0117-00 [J]
Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos)
Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento adecuado a estos productos y a sus subproductos residuales correspondientes. Póngase en contacto con su administración local para obtener información sobre el punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos perjudiciales en la salud y el medio ambiente.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
FCC NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Informação sobre a eliminação de pilhas
Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou importador. A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.
CALIFORNIA, USA ONLY
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material— special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
i
Para cumplimiento de la COFETEL:
“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda
causar su operación no deseada”
IC (Industry Canada) Notice
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device. The term “IC: ” before the certification/ registration number only signifies that the Industry Canada technical specification were met.
Note de IC (Industrie Canada)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement. L’expression “IC:” avant le numéro d’homologation/ enregistrement signifie seulement que les specifications techniques d’Industrie Canada ont été respectées.
Contains Bluetooth Module FCC ID: ZWYMC55 Contains Bluetooth Module IC: 12033A-MC55
CAUTION
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
ATTENTION
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation de l’exposition maximale autorisée. Cependant, cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et chevilles).
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.
ii
CONTENTS
BEFORE USE
BEFORE USE 2
BASICS 3
GETTING STARTED 4
USB / iPod / ANDROID 5
RADIO 7
AUX 8
Pandora® 9
iHeartRadio® 10
SiriusXM® Radio 11
BLUETOOTH® 14
AUDIO SETTINGS 20
DISPLAY SETTINGS 22
MORE INFORMATION 23
TROUBLESHOOTING 24
SPECIFICATIONS 27
INSTALLATION / CONNECTION 28
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.
Remote control (RM-RK52):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used batteries promptly. If swallowed, contact a physician immediately.
How to read this manual
• Operations are explained mainly using buttons on the faceplate.
• [
XX
] indicates the selected items.
• (
XX
) indicates references are available on the stated page.
Maintenance
Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft cloth.
Cleaning the connector: Detach the faceplate and clean the connector gently with a cotton swab, being careful not to damage the connector.
Connector (on the reverse side of the faceplate)
2
BASICS
Volume knob
(turn/press) Display window
Detach button
Attach
Detach
How to reset
Your preset adjustments will also be erased.
Remote control (RM-RK52)Faceplate
Remote sensor (Do not expose to bright sunlight.)
Pull out the insulation sheet when using for the first time.
How to replace the battery
To On the faceplate On the remote control
Turn on the power
Adjust the volume Turn the volume knob. Press
Select a source
Change the display information
Press
• Press and hold to turn off the power.
Press the volume knob to mute the sound or pause playback.
• Press again to cancel.
• Press
• Press Press
.
repeatedly. , then turn the volume knob within 2 seconds.
repeatedly. (
24
)
or .
Press
• Press again to cancel. Press SOURCE repeatedly.
to mute the sound or pause playback.
ENGLISH
3

GETTING STARTED

1
Cancel the demonstration
Press and hold .
1 2 Turn the volume knob to select [ 3 Turn the volume knob to select [
DEMO
], then press the knob.
DEMOOFF
], then press the knob.
4 Press to exit.
2
Set the clock
Press and hold .
1 2 Turn the volume knob to select [ 3 Turn the volume knob to select [
CLOCK
], then press the knob.
CLOCKSET
], then press the knob.
4 Turn the volume knob to make the settings, then press the knob.
Day
5 Turn the volume knob to select [ 6 Turn the volume knob to select [
Hour Minute
knob.
24H/ 12H 12 HOUR
], then press the knob.
] or [
24 HOUR
], then press the
7 Press to exit.
To return to the previous setting item, press
.
SETTINGS
BEEP
SRC SELECT
AM
*
PANDORA
IHEART
AUX
*
*
ON
:Activates the keypress tone.;
ON
:Enables AM in source selection.;
*
ON
:Enables PANDORA in source selection.;
ON
:Enables IHEARTRADIO in source selection.;
ON
:Enables AUX in source selection.;
OFF
F/W UPDATE
SYSTEM / BLUETOOTH
F/W xxxx
CLOCK
CLOCK SYNC
CLOCK DISP ON
* Not displayed when the corresponding source is selected.
YES
:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated). For details on how to update the firmware, see: <http://www.jvc.net/cs/car/>.
AUTO
:The clock time is automatically set using the Clock Time (CT) data
in FM Radio Broadcast Data System signal.;
:The clock time is shown on the display even when the unit is turned
off.;
OFF
:Cancels.
:Deactivates.
OFF
:Disables.
OFF
OFF
:Disables.
OFF
:Disables.
OFF
:Disables.
:Cancels.
Default:
XX
3
Set the basic settings
Press and hold .
1 2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit.
To return to the previous setting item, press
.
4
USB / iPod / ANDROID
Start playback
The source changes automatically and playback starts.
USB input terminal
USB
USB 2.0 cable (commercially available)
*1
iPod/iPhone
(Accessory of the iPod/ iPhone)*
ANDROID
Micro USB 2.0 cable (commercially available)
1
2
*
1
*
To On the faceplate On the remote control
3
Reverse / Fast-forward
Select a file Press
4
Select a folder
Repeat play
Random play
*
5
*
5
*
*
Press and hold .
.
Press and hold
Press
Press . Press .
Press repeatedly.
TRACK RPT/ RPT OFF
: JVC Playlist Creator (JPC) / JVC Music
Control (JMC) file (
TRACK RPT/ FOLDER RPT/ RPT OFF ONE RPT/ ALL RPT/ RPT OFF
: MP3/WMA/AAC/WAV/FLAC file
: iPod or ANDROID
Press repeatedly.
FOLDERRND/ ALL RND/ RND OFF
: MP3/WMA/AAC/WAV/FLAC file or JPC /
.
.
24
)
JMC file
SONG RND/ ALL RND/ RND OFF
1
*
Do not leave the cable inside the car when not using.
2
*
When connecting an Android device, “Press [VIEW] to install JVC MUSIC PLAY APP” is shown. Follow the instructions to install the
: iPod or ANDROID
application. You can also install the latest version of JVC MUSIC PLAY application on your Android device before connecting. (
23
)
3
*
For ANDROID: Applicable only when [
4
*
Only for MP3/WMA/AAC/WAV/FLAC files. This does not work for iPod/ ANDROID.
5
*
For iPod/ ANDROID: Applicable only when [
AUTO MODE
HEAD MODE
] is selected. (6)
]/ [
AUTO MODE
] is selected. (6)
ENGLISH
5
USB / iPod / ANDROID
To On the faceplate
Select control mode
Select music drive
While in iPod source, press repeatedly.
HEAD MODE IPHONE MODE
While in ANDROID source, press repeatedly.
AUTO MODE
AUDIO MODE
Press
The stored songs in the following start playback.
• Selected internal or external memory of a smartphone (Mass Storage Class).
• Selected drive of a multiple drives device.
: Control from the unit.
: Control from the iPod/iPhone.
can still play/pause or file skip from the unit.
: Control from the unit (using JVC MUSIC
PLAY application).
: Control other media player applications
from the Android device (without using JVC MUSIC PLAY application). However, you can still play/pause or file skip from the unit.
repeatedly.
However,
Change the playback speed of the Audiobook
While listening to the iPod and [
HEADMODE
] is selected (
Select control mode
1 Press and hold . 2 Turn the volume knob to select [ 3 Press the volume knob to select [
IPOD
], then press the knob.
AUDIOBOOKS
].
4 Turn the volume knob to make a selection, then press the knob.
0.5×SPEED
Audiobooks sound file in your iPod/iPhone.
(Default: Depends on your iPod/iPhone setting.)
/
1×SPEED
/
2×SPEED
: Select the desired playback speed of the
5 Press to exit.
To return to the previous setting item, press
.
you
)....
Select a file from a folder/list
Press .
1 2 Turn the volume knob to select a folder/list, then press the
knob.
3 Turn the volume knob to select a file, then press the knob.
Quick Search
If you have many files, you can search through them quickly.
For MP3/WMA/AAC/WAV/FLAC or JPC / JMC file:
Turn the volume knob quickly.
For iPod:
You can search for a file according to the first character. Press desired character (A to Z/ 0to9/ OTHERS).
• Select “OTHERS” if the first character is other than Ato Z, 0 to 9.
• To return to the previous setting item, press
• To cancel, press and hold
• For iPod, applicable only when [
control mode
• For ANDROID, applicable only when [ (
Select control mode
or turn the volume knob quickly to select the
.
.
HEADMODE
)
)
] is selected. ( 
AUTO MODE
] is selected.
Select
6
RADIO
“ST” lights up when receiving an FM stereo broadcast with sufficient signal strength.
Search for a station
Press repeatedly to select FM or AM.
1 2 Press (or press on RM-RK52) to search for a station automatically. (or) Press and hold (or press and hold on RM-RK52) until “M” flashes,
then press repeatedly to search for a station manually.
Settings in memory
You can store up to 18 stations for FM and 6 stations for AM.
Store a station
While listening to a station....
Press and hold one of the number buttons (1 to 6).
(or) 1 Press and hold the volume knob until “PRESETMODE” flashes. 2 Turn the volume knob to select a preset number, then press the knob.
The preset number flashes and “MEMORY” appears.
Other settings
Press and hold .
1 2 Turn the volume knob to select [
knob.
3 Turn the volume knob to make a selection
following table
)
, then press the knob.
TUNER
], then press the
(
see the
4 Repeat step 3 until the desired item is selected/
activated or follow the instructions stated on the selected item.
5 Press to exit.
To return to the previous setting item, press
RADIO TIMER
1
*
Selectable only when SiriusXM Vehicle Tuner is connected. (
2
*
Selectable only when [
Turns on the radio at a specific time regardless of the current source.
1 ONCE/ DAILY/ WEEKLY/ OFF
timer will be turned on.
2 FM/ AM/ SIRIUS XM 3 01
to 18 (for FM/ SIRIUS XM)/ 01 to 06 (for
AM):Select the preset station.
4
Set the activation day *2 and time.
M
” lights up when complete.
Radio Timer will not activate for the following cases.
• The unit is turned off.
• [
OFF
] is selected for [AM] in [
Timer for AM is selected. (
ONCE
] or [
*1:Select the source.
WEEKLY
:Select how often the
SRCSELECT]
4
)
] is selected in step 1.
.
Default:
after Radio
11
XX
)
Select a stored station
Press one of the number buttons (1to6).
(or) 1 Press 2 Turn the volume knob to select a preset number, then press the knob to
confirm.
ENGLISH
7
RADIO
AUX
SSM SSM01–06
to 18 stations for FM. “SSM” stops flashing when the first 6 stations are stored. Select stations.
IF BAND AUTO
MONO ON
AREA AREAUS
PTY SEARCH
PTY code: NEWS, INFORM
rock),
NOSTALGA SOFTR&B RELTALK
(Spanish talk),
3
*
ADLTHIT
(adult hits),
(nostalgia),
(soft rhythm and blues),
(religious talk),
MUSCESP
:Increases the tuner selectivity to reduce interference noises from adjacent FM stations. (Stereo effect may be lost.); interference noises from adjacent FM stations, but sound quality will not be degraded and the stereo effect will remain.
:Improves the FM reception, but the stereo effect will be lost.;
OFF
:Cancels.
10kHz/200kHz.; FM intervals: 10kHz/50kHz.; intervals: 9kHz/50kHz.
Select a PTY code (see below). If there is a station broadcasting a program of the same PTY code as you have selected, that station is tuned in.
(information),
JAZZ, CLASSICL
PERSNLTY
(Spanish music),
/
SSM07–12
SSM07–12
: For North/Central/South America, AM/FM intervals:
AREASA
SOFTRCK
(personality),
/
SSM13–18
/
SSM13–18
:For some South American countries, AM/
AREAEU
SPORTS, TALK, ROCK, CLSROCK
(softrock), (classical),
LANGUAGE, RELMUSC
TOP40, COUNTRY, OLDIES, SOFT
R&B
HIPHOP, WEATHER
:Automatically presets up
to store the following 12
WIDE
:For any other areas, AM/FM
(rhythm and blues),
(religious music),
PUBLIC, COLLEGE, HABLESP
:Subjects to
Default:
(classic
XX
Use a portable audio player
Connect a portable audio player (commercially available).
1
3.5mm (1/8") stereo mini plug with “L” shaped connector (commercially available)
Auxiliary input jack
2 Select [
ON
] for [
AUX
] in [
SRC SELECT
Portable audio player
]. (4)
3 Press repeatedly to select AUX. 4 Turn on the portable audio player and start playback.
Use a 3-core plug head stereo mini plug for optimum audio output.
,
3
*
Only for FM source.
8
Pandora®
Preparation:
Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then create an account and log in to Pandora.
• Select [
ON
] for [

PANDORA

] in [
SRC SELECT
]. (4)
Start listening
Open the Pandora application on your device.
1 2 Connect your device to the USB input terminal.
USB input terminal
1
(Accessory of the iPod/iPhone)
*
The source changes to PANDORA and broadcast starts.
To On the faceplate On the remote control
Playback / pause Press the volume knob.
Skip a track
Thumbs up or thumbs down*
1
*
Do not leave the cable inside the car when not using.
2
*
If thumbs down is selected, the current track is skipped.
Press T. Press I.
Press .
2
Press
Press
.
.
Create and save a new station
Press .
1 2 Turn the volume knob to select [ 3 Turn the volume knob to select [
press the knob.
A new station is created based on the current song or artist.
NEW STATION FROM TRACK
], then press the knob.
] or [
FROM ARTIST
], then
4 Press and hold number button 1, 4, 5 or 6 to store.
To select a stored station, press number button 1, 4, 5 or 6.
Search for a registered station
Press .
1 2 Turn the volume knob to make a selection, then press the knob.
[ [
BYDATE]: A-Z]:
According to the registered date. Alphabetical order.
3 Turn the volume knob to the desired station, then press the knob.
To cancel, press and hold
.
Bookmark a song or artist information
Press and hold the volume knob.
1 2 Turn the volume knob to make a selection, then press the knob.
[
THIS TRACK
[
THIS ARTIST
“BOOKMARKED” appears and the information is stored to your device. The bookmark is available on your Pandora account but not on this
unit.
]: Current song information
]: Current artist information
ENGLISH
9
iHeartRadio®
Preparation:
Install the latest version of iHeart Link for JVC application on your device (iPhone/ iPod touch), then create an account and log in to iHeartRadio.
• Select [
ON
] for [
IHEART
] in [
SRC SELECT
]. (4)
Start listening
Open the iHeart Link application on your device.
1 2 Connect your device to the USB input terminal.
USB input terminal
1
(Accessory of the iPod/iPhone)
*
3 Press repeatedly to select IHEARTRADIO.
Broadcast starts automatically
To
Playback / pause Press the volume knob.
On the faceplate On the remote control
Press
.
Search for a station
Press .
1 2 Turn the volume knob to select a category, then
press the knob.
3 Turn the volume knob to the desired station, then
press the knob.
When a city list appears, you can skip cities in
alphabetical order.
To cancel, press and hold
.
Skip cities by alphabetical order
While a city list appears during search...
1 Turn the volume knob quickly to enter character
search.
You can search through the list quickly according to
the first character (A to Z).
2 Turn the volume knob or press to select the
character to be search for.
3 Press the volume knob to start searching.
To cancel, press and hold
.
Skip a track for custom station
Thumbs up or thumbs down for custom station*
Create a new/custom station Press and hold the volume
Add to favorite stations for live station
Scan for live station Press 4.—
1
*
Do not leave the cable inside the car when not using.
2
*
If thumbs down is selected, the current track is skipped.
2
Press T. Press I.
Press .
knob.
Press 1.—
Press
.
10
SiriusXM® Radio
Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.com.
Preparation:
1 Connect the optional SiriusXM Vehicle Tuner
(commercially available).
Antenna
SiriusXM
Expansion port on the rear panel
Vehicle Tuner
2 Check your Radio ID for activation.
The SiriusXM Radio ID is required for activation and
can be found by tuning to Channel 0 as well as on the label found on the SiriusXM Connect tuner and its’ packaging.
The Radio ID does not include the letters I, O, S or F.
3 Activate the subscription.
For users in U.S.A.:
Online: Go to www.siriusxm.com Phone: Call 1-866-635-2349
For users in Canada:
Online: Go to www.siriusxm.ca/activatexm Phone: Call 1-877-438-9677 4 Press repeatedly to select SIRIUSXM
to start updating.
Start listening
Press repeatedly to select SIRIUSXM.
1 2 Press .
” lights up.
3 Turn the volume knob to select a CATEGORY, then press the knob. 4 Turn the volume knob to select a category from the list, then press the knob.
If “ALL CHANNEL” is selected, all the available channels will be shown.
5 Turn the volume knob to select a channel, then press the knob. (or) Press to search for a channel manually.
• Pressing and holding changes the channel rapidly.
If a locked channel or a mature channel is selected, a pass code input screen appears. Enter the pass code to receive the channel.
( 13)
Store a channel
You can store up to 18 channels.
To Do this
Store a channel Press and hold one of the number buttons (1 to 6).
1 Press and hold the volume knob until “PRESETMODE” flashes. 2 Turn the volume knob to select a preset number, then press
the knob.
The preset number flashes and “MEMORY” appears.
Select a stored channel
Press one of the number buttons (1 to 6).
1 Press . 2 Turn the volume knob to select PRESET, then press the knob. 3 Turn the volume knob to select a preset number, then press
the knob.
Press
on RM-RK52.
ENGLISH
11
SiriusXM® Radio
SiriusXM Replay™
Press the volume knob.
1
” lights up and the unit memorizes this paused position.
2 Press the volume knob to start Replay.
Replay starts from the paused position in step
During Replay...
To On the faceplate On the remote control
Playback / pause Press the volume knob.
Skip the current song backward/forward
Rewind / Fast-forward
Go to Live and exit Reply
Press .
Press and hold
.
Press and hold the volume knob.
1 Press .
1.
Press
Press
Press and hold
.
2 Turn the volume knob to select LIVE, then
press the knob.
SmartFavorites and TuneStart™
When you select a SmartFavorites channel, you can rewind and replay up to 30 minutes of any of the missed news, talk, sports or music content.
• Playback starts from the beginning of the song if [ [
ON
] ( 13) for most music channels stored as a SmartFavorite.
To On the faceplate
Select a stored SmartFavorite channel
Press one of the number buttons (1to6).
1 Press . 2 Turn the volume knob to select PRESET, then
press the knob.
TUNE START
] is set to
3 Turn the volume knob to select a preset number,
then press the knob to confirm.
Cancel
.
SmartFavorites channels
1 Press . 2 Turn the volume knob to select PRESET, then
press the knob.
3 Turn the volume knob to select a preset number,
then press and hold the knob.
” are removed from the last character.
*
Reassign SmartFavorites channels
Repeat steps channels.
” appears at the last character.
*
1 to 3 of cancelling SmartFavorites
User preset channels are initially assigned as the SmartFavorites channels. SmartFavorite channel is available with SXV200 or later SiriusXM tuner models. SiriusXM Vehicle Tuner automatically buffers the broadcast audio content of the SmartFavorites channels in the background.
Using SXV200: This unit can assign a maximum of 6 SmartFavorites channels. If you try to assign the 7th channel, an error beep tone will be heard. Initially, preset channels 1 to 6 are assigned as SmartFavorites.
Using SiriusXM tuner models later than SXV200: This unit can assign
a maximum of 18 SmartFavorites channels. Initially, all preset channels are assigned as SmartFavorites.
• “
” appears at the last character of the channel name for the
*
SmartFavorites channels.
12
TuneScan™
You can get a short preview of the songs that you have missed on each of your SmartFavorite music channels or current tuned music channel.
1 Press . 2 Turn the volume knob to select TUNE SCAN, then press the knob.
Scanning start for the first 6 seconds of the recorded music contents.
• To listen to the current song, press the volume knob to stop scanning. The unit continues playing the current song.
• To select the previous/next song, press
• To cancel scanning, press and hold the volume knob. Playback returns to the channel before you enter TuneScan.
.
SiriusXM® Radio
SiriusXM settings
Press and hold .
1 2 Turn the volume knob to select [
SIRIUSXM
], then press the knob.
3 Turn the volume knob to make a selection (see the following table), then
press the knob.
4 Repeat step 3 until the desired item is selected/activated or follow the
instructions stated on the selected item.
5 Press to exit.
To return to the previous setting item, press
CH LOCK
To unlock settings:
1
Turn the volume knob to select a number.
2
Press to move to the entry position.
3
Repeat steps 1 and 2 to enter the current pass code.
(Initial pass code is 0000.)
4
Press the volume knob to confirm.
.
Default:
XX
2
TUNE START
SIGNAL LVL NO SIGNAL/ WEAK/ GOOD/ STRONG
BUF USAGE 0%
SXM RESET YES
1
*
Displayed only when [
2
*
Available only if the connected SiriusXM Vehical Tuner is SXV200 or later that
supports SmartFavorites.
*
ON
:Selected SmartFavorite channel starts playback from
the beginning of the song.;
of the current received signal.
—
100%(0
buffer.
:Resets stored channel and lock setting to default.;
NO
:Cancels.
USER DEFINED
OFF
:Cancels.
:Shows the strength
):Shows the memory usage for Replay
] is selected.
CODESET
LOCK SET MATURE CH
1
CHEDIT
CHCLEAR
*
1
*
1
Press the volume knob to enter [
2
Turn the volume knob to select a number.
3
Press to move to the entry position.
4
Repeat steps 2 and 3 to enter a new 4-digit pass code.
5
Press the volume knob to confirm.
6
Repeat steps 2 to 5 to reconfirm the pass code.
• Make a note of the new pass code to enter channel lock settings from next time.
user-defined lock setting.;
1
Turn the volume knob to select a category, then press the knob.
2
Turn the volume knob to select a channel you want to lock, then press the knob.
“L” appears in front of the channel number.
3
Press and hold
YES
:Clears all the locked channels.; NO:Cancels.
NEW CODE
:Selects the SiriusXM-defined lock setting.;
OFF
:Cancels.
to exit.
].
USER DEFINED
:Selects the
ENGLISH
13
BLUETOOTH®
BLUETOOTH — Connection
Supported Bluetooth profiles
– Hands-Free Profile (HFP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP)
Supported Bluetooth codecs
– Sub Band Codec (SBC) – Advanced Audio Coding (AAC)
Connect the microphone
Rear panel
Microphone (supplied)
Microphone input jack
Adjust the microphone
Secure using cord clamps (not supplied) if necessary.
angle
14
Pair a Bluetooth device
When connecting a Bluetooth device to the unit for the first time, perform pairing between the unit and the device.
1 Press to turn on the unit. 2 Search and select “JVC UNIT” on the Bluetooth device.
“BTPAIRING” flashes on the display.
• For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN)
code immediately after searching.
• Refer also to the manual supplied with your Bluetooth device. 3 Perform (A) or (B) depending on what scrolls on the display.
For some Bluetooth devices, pairing sequence may vary from the steps described below.
(A) “[Device Name]” “XXXXXX” “VOL–YES” “BACK–NO” “XXXXXX” is a 6-digit passkey randomly generated during each pairing.
Ensure that the passkey which appears on the unit and Bluetooth device is the same. Press the volume knob to confirm the passkey. Operate the Bluetooth device to confirm the passkey.
(B) “[Device Name]” “VOL–YES” “BACK–NO”
• If only “PAIRING” appears, operate the Bluetooth device to confirm pairing. “PAIRING COMPLETED” appears when pairing is completed and “ connection is established.
• Up to five devices can be registered (paired) in total.
• Only one Bluetooth device can be connected at any time.
• This unit supports Secure Simple Pairing (SSP).
• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually. Refer to the instruction manual of the Bluetooth device for more information.
• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device,
• When you connect iPhone/ iPod touch/ Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated. Press the volume knob to pair once you have confirmed the device name.
Automatic pairing request is activated only if: – Bluetooth function of the connected devcie is turned on. – [ – JVC MUSIC PLAY application is installed on the Android device.
Press the volume knob to start pairing.
• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the Bluetooth device.
18)
” will light up when the Bluetooth
AUTO CNNT
You can change to a desired PIN code before pairing. (
18, [
DELETE PAIR
] is set to [ON]. ( 18)
].
BLUETOOTH®
BLUETOOTH — Mobile phone
Receive a call
When there is an incoming call: – All the buttons flash. – The unit answers the call automatically if [
During a call: – If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.
To On the faceplate On the remote control
Answer a call
Reject a call
End a call
Press
Press and hold knob.
Press and hold knob.
AUTO ANSWER
or the volume knob.
] is set to a selected time. ( 16)
or the volume
or the volume
Press
Press and hold
Press and hold
.
Improve the voice quality
While talking on the phone....
1 Press and hold . 2 Turn the volume knob to make a selection
(
see the following table), then press the
knob.
3 Repeat step 2 until the desired item is
selected or activated.
4 Press to exit.
To return to the previous setting item, press
.
MIC LEVEL
NOISE RDCT –5
.
ECHO CANCEL –5
.
–10
—
+10(–4
the microphone increases as the number increased.
—+5(0):Adjust the noise reduction level until the least noise is being heard during a phone conversation.
—+5(0):Adjust the echo cancellation delay time until the least echo is being heard during a phone conversation.
):The sensitivity of
Default:
XX
Adjust the phone volume [
00
] to [50] (Default: [15]*)
Switch between hands­free and private talk modes
* Not applicable for iPhone. During a call, the unit synchronizes the phone volume on the iPhone to the unit.
Turn the volume knob during a call.
• This adjustment will not affect the volume of the other sources.
Press the volume knob during a call.
• Operations may vary according to the connected Bluetooth mobile phone.
ENGLISH
15
BLUETOOTH®
Make the settings for receiving a call
Press to enter Bluetooth mode.
1 2 Turn the volume knob to make a selection
(see the following table), then press the knob.
3 Repeat step 2 until the desired item is
selected or activated.
To return to the previous setting item, press
.
XX
SETTINGS
AUTO ANSWER
Default:
01 SEC —30 SEC
incoming call automatically in the selected time (in seconds).;
OFF
:Cancels.
:The unit answers
Make a call
You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature.
1 Press to enter Bluetooth mode. 2 Turn the volume knob to make a selection (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on
the selected item.
To return to the previous setting item, press
1
RECENT CALL
Press the volume knob to select a name or a phone number.
• “>” indicates call received, “<“ indicates call made, “M” indicates call missed.
• “NO HISTORY” appears if there is no recorded call history or call number.
2
Press the volume knob to call.
.
16
PHONEBOOK
1
Press to select the desired letter (A to Z, 0to9, and OTHERS).
• “OTHERS” appears if the first character is other than Ato Z, 0 to 9.
2
Turn the volume knob to select a name, then press the knob.
3
Turn the volume knob to select a phone number, then press the knob to call.
• If the phone supports PBAP, the phonebook of the connected phone is automatically transferred to the unit when pairing.
• This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as “U”.)
BLUETOOTH®
DIAL NUMBER
VOICE
1
Turn the volume knob to select a number (0 to 9) or character ( , #,
+).
2
Press to move the entry position.
Repeat steps
3
Press the volume knob to call.
Speak the name of the contact you want to call or the voice command to control the phone functions.
1
and 2 until you finish entering the phone number.
( 
Make a call using voice recognition
Make a call using voice recognition
Press and hold to activate the connected phone.
1 2 Speak the name of the contact you want to call or the voice
command to control the phone functions.
• Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.
• This unit also supports the intelligent personal assistant function of iPhone.
Delete a contact
Press to enter Bluetooth mode.
1 2 Turn the volume knob to select [
RECENTCALL
], then press the knob.
3 Turn the volume knob to select a contact. 4 Press and hold to enter delete mode. 5 Turn the volume knob to select [
the knob.
DELETE
: Selected name or phone number in step 3 is deleted.
DELETE ALL
deleted.
: All names or phone numbers in [
6 Turn the volume knob to select [
• To return to the previous setting item, press
• Not applicable for mobile phone that supports PBAP.
DELETE
] or [
DELETE ALL
RECENTCALL
YES
], then press the knob.
.
], then press
] in step 2 is
Settings in memory
Store a contact in memory
You can store up to 6 contacts into the number buttons (1 to 6).
1 Press to enter Bluetooth mode. 2 Turn the volume knob to select [
[
)
DIALNUMBER
3 Turn the volume knob to select a contact or enter a phone number.
If a contact is selected, press the volume knob to show the phone
number.
], then press the knob.
RECENTCALL
], [
PHONEBOOK
], or
4 Press and hold one of the number buttons (1 to 6).
“MEMORY P(selected preset number)” appears when the contact is
stored.
To erase a contact from the preset memory, select [ and store a blank number.
DIALNUMBER
Make a call from memory
Press to enter Bluetooth mode.
1 2 Press one of the number buttons (1 to 6). 3 Press the volume knob to call.
“NO PRESET” appears if there is no contacts stored.
Bluetooth mode settings
Press and hold .
1 2 Turn the volume knob to select [ 3 Turn the volume knob to make a selection
knob.
BLUETOOTH
], then press the knob.
( 18)
, then press the
4 Repeat step 3 until the desired item is selected/activated or follow
the instructions stated on the selected item.
5 Press to exit.
To return to the previous setting item, press
.
] in step 2
ENGLISH
17
BLUETOOTH®
Default:
PHONE
AUDIO
APPLICATION
DELETE PAIR
1
*
1
*
*
Selects the phone or audio device to connect or disconnect. “
” appears in front of the device name when connected.
1
Shows the connected phone name using the JVC Smart Music Control app. “
” appears in front of the device name when connected.
1
Turn the volume knob to select a device to delete, then press the
knob.
2
SET PINCODE (0000)
Changes the PIN code (up to 6 digits).
1 2
Repeat steps
3
AUTO CNNCT ON
Bluetooth device is within range.;
AUTO PAIR ON
Turn the volume knob to select [
Turn the volume knob to select a number. Press to move the entry position.
1
and 2 until you finish entering the PIN code.
Press the volume knob to confirm.
:The unit automatically reconnect when the last connected
:The unit automatically pair supported Bluetooth device (iPhone/
YES
] or [NO], then press the knob.
OFF
:Cancels.
iPod touch/ Android device) when it is connected through USB input terminal.Depending on the operating system of the connected device, this function may not work. ;
INITIALIZE YES
:Initializes all the Bluetooth settings (including stored pairing,
phonebook, and etc.).;
INFORMATION
1
*
You can only connect another Bluetooth device by disconnecting the connected Bluetooth
device first. “
2
*
JVC Smart Music Control is designed to view JVC car receiver status and perform simple
MYBTNAME MYADDRESS
: Displays the unit name (JVCUNIT).;
: Shows address of this unit.
” disappears when disconnected.
NO
OFF
:Cancels.
:Cancels.
control operations on Android smart phones. For JVC Smart Music Control operations, visit JVC website: <http://www.jvc.net/cs/car/>.
XX
Bluetooth compatibility check mode
You can check the connectivity of the supported profile between the Bluetooth device and the unit.
• Make sure there is no Bluetooth device paired.
*2
1 Press and hold .
“BLUETOOTH”
PHONE”
“PIN IS 0000” scrolls on the display.
“CHECK MODE” appears. “SEARCH NOW USING
2 Search and select “JVC UNIT” on the Bluetooth device within
3minutes.
3 Perform (A), (B) or (C) depending on what appears on the display.
(A) “PAIRING”
passkey appears on the unit and Bluetooth device, then operate
the Bluetooth device to confirm the passkey. (B) “PAIRING” (C) “PAIRING”: Operate the Bluetooth device to confirm pairing.
After pairing is successful, “PAIRING OK” Bluetooth compatibility check starts. If “CONNECT NOW USING PHONE” appears, operate the Bluetooth device to allow phonebook access to continue.
“XXXXXX” (6-digit passkey): Ensure that the same
“PIN IS 0000”: Enter “0000” on the Bluetooth device.
“[Device Name]” appears and
The connectivity result flashes on the display.
“PAIRING OK” and/or “H.FREE OK”*1 and/or “A.STREAM OK”*2 and/or “PBAP OK”*
1
*
Compatible with Hands-Free Profile (HFP)
2
*
Compatible with Advanced Audio Distribution Profile (A2DP)
3
*
Compatible with Phonebook Access profile (PBAP)
After 30 seconds, “PAIRING DELETED” appears to indicate that pairing has been deleted, and the unit exits check mode.
• To cancel, press and hold
on the power again.
3
: Compatible
to turn off the power, then turn
18
BLUETOOTH®
BLUETOOTH — Audio
Audio player via Bluetooth
Press repeatedly to select BTAUDIO (or press SOURCE on RM-RK52).
1 2 Operate the Bluetooth audio player to start playback.
To On the faceplate On the remote control
Playback / pause
Select group or folder Press
Reverse / Forward skip
Reverse / Fast-forward Press and hold
Repeat play Press
Random play
Operations and display indications may differ according to their availability on the connected device.
Press
Press
TRACKRPT, ALLRPT, RPTOFF
Press
GROUPRND, ALLRND, RNDOFF
.
. Press .
.
repeatedly.
repeatedly.
.
Press
Press
Press and hold
.
.
Internet radio via Bluetooth
Listen to Pandora
Preparation:
Select [ You can listen to Pandora on your smart phone
(Android OS) through Bluetooth on this unit.
ON
] for [
PANDORA
] in [
SRC SELECT
].
( 4)
1 Open the Pandora application on your device. 2 Connect your Bluetooth audio player via
Bluetooth connection. (
14)
3 Press repeatedly to select PANDORA.
The source switches and broadcast starts
automatically.
You can operate Pandora in the same way as Pandora for iPod/iPhone. (
9)
Listen to iHeartRadio
Preparation:
Select [
.
You can listen to iHeartRadio on your smart phone (Android OS) through Bluetooth on this unit.
ON
] for [
IHEART
] in [
SRC SELECT
].
( 4)
1 Open the iHeart Link application on your smart
phone.
2 Connect your smart phone via Bluetooth
connection. (
14)
3 Press repeatedly to select
IHEARTRADIO.
The source switches and broadcast starts
automatically.
You can operate iHeartRadio in the same way as iHeartRadio for iPod/iPhone. (
10)
ENGLISH
19

AUDIO SETTINGS

To
Select a preset equalizer
Store your own sound settings
On the faceplate
Press repeatedly.
Press within 2seconds.
Preset equalizer: FLAT R&B, TALK, USER1, USER2, VOCAL BOOST, BASS BOOST CLASSICAL, DANCE
, then turn the volume knob
(default),
HARD ROCK, JAZZ, POP
1 Press and hold . 2 Turn the volume knob to select [
press the knob.
3 Turn the volume knob to select [
[
USER2
], then press the knob.
EASY EQ
USER1
] or
,
,
], then
4 Turn the volume knob to make a selection,
then press the knob.
For settings, refer to step
• To return to the previous setting item, press
• To exit, press
2 of [
.
EASYEQ
].
Other settings
Press and hold .
1 2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press
.
.
EQSETTING
EQPRESET
EASYEQ
PRO EQ
1
*
Displayed only when [
2
*
Displayed only when [
3
*
Displayed only when [
FLAT/ VOCALBOOST/
equalizer.
1 USER1/ USER2 2
SUB.W SP SUB.W
1 USER1/ USER2 2 BASS 3
Level: Q:
Level: Q:
Level: Q:
HARD ROCK/
Adjust your own sound settings.
1*3
*
BASSLVL MIDLVL: TRELVL
Adjust the sound elements of the selected sound tone.
BASS
MIDDLE
TREBLE
:
:
/
MIDDLE
Frequency: 60/ 80/
Frequency:
Frequency:
SUB.W SPK/PREOUT SPK/PREOUT
JAZZ/
POP/
BASSBOOST/
:Select a preset name.
1*2
*
:
:
:Select a preset name.
/
TREBLE
:Select a sound tone.
–06
to
Q1.0/ Q1.25/ Q1.5/ Q2.0
0.5/ 1.0/ 1.5/ 2.5KHZ –06
to
Q0.75/ Q1.0/ Q1.25
10.0/ 12.5/ 15.0/ 17.5KHZ –06
to
QFIX
] is set to [ON]. ( 21)
] is set to [ ] is set to [
R&B/
TALK/
USER1/
CLASSICAL/
00
to
–08 –06 –06 –06
100/ 200HZ
+06
+06
+06
SUB.W/SUB.W REAR/SUB.W
DANCE
+06
(Default:
to
+08
to
+06
to
+06
to
+06
00)
(
(Default:
]. ( 21)
] or [
Default:
USER2/
:Selects a preset
Default:
(Default:
SUB.W/SUB.W
03 00 00 00
80HZ 00 Q1.0
)
1.0KHZ 00 Q1.25
)
10.0KHZ 00 QFIX
)
]. ( 21)
XX
20
AUDIO SETTINGS
AUDIO
BASS BOOST
+01
LOUD 01
sound at low volume.;
4
SUB.W LEVEL
*
SPK-OUT
PRE-OUT
6
*
SUB.W
SUB.WLPF
*
ON
4
THROUGH MID85HZ
55Hz/ 85Hz/ 120Hz are sent to the subwoofer.
4
SUB.WPHASE
*
REVERSE
output to be in line with the speaker output for optimum performance. (Selectable only if a setting other than [ [
SUB.WLPF
FADER R06
7
BALANCE
*
L06
/
+02
: Selects your preferred bass boost level.;
OFF
:Cancels.
/02:Boosts low or high frequencies to produce a well-balanced
OFF
:Cancels.
5
*
00
to
+06(+03
subwoofer connected via speaker lead. (
6
*
–08
to
+08(00
):Adjusts the output level of the
29)
):Adjusts the output level of the subwoofer connected to the lineout terminals (REAR/ SW) through an external amplifier. (
/
OFF
: Turns on or off the subwoofer output.
:All signals are sent to the subwoofer. ; /
HIGH120HZ
(180°)/
:Audio signals with frequencies lower than
NORMAL
(0°):Selects the phase of the subwoofer
THROUGH
29)
LOW55HZ
/
] is selected for
].)
—
F06(00
):Adjusts the front and rear speaker output balance.
—
R06(00
):Adjusts the left and right speaker output balance.
D.T.EXP
(Digital Track Expander)
SPK/PREOUT
4
*
Displayed only when [
5
*
Displayed only when [
6
*
Displayed only when [
7
*
This adjustment will not affect the subwoofer output.
ON
:Creates realistic sound by compensating the high-frequency components and restoring the rise-time of the waveform that are lost in audio data compression.;
OFF
Selects the appropriate setting to get the desired output. (
following table
SUB.W
SPK/PREOUT
SPK/PREOUT
.)
] is set to [ON].
] is set to [ ] is set to [
SUB.W/SUB.W REAR/SUB.W
SPK/PRE OUT
Connection via lineout terminals (29)
Setting
REAR/REAR
REAR/SUB.W
SUB.W/SUB.W
FRONT REAR/SW
Front speakers output Rear speakers output
Front speakers output Subwoofer output
Front speakers output Subwoofer output
Lineout terminal
Connection via speaker leads ( 29)
:Cancels.
].
] or [
SUB.W/SUB.W
See the
].
VOL ADJUST –05
—
+05(00
(compared to the FM volume level). Before adjustment, select the source you want to adjust. (“VOLADJFIX” appears if FM is selected.)
AMP GAIN LOWPOWER
maximum power of each speaker is less than 50W to prevent damaging the speakers.);
):Presets the volume adjustment level of each source
:Limits the maximum volume level to 30. (Select if the
HIGHPOWER
:The maximum volume level is 50.
Setting
REAR/REAR
REAR/SUB.W
SUB.W/SUB.W
If [
SUB.W/SUB.W
– [
HIGH120HZ
– [
R01
] is selected in [
Rear speaker lead
L (left) R (right)
Rear speakers output Rear speakers output
Rear speakers output Rear speakers output
Subwoofer output (Mute)
] is selected:
] is selected in [
FADER
SUB.WLPF
] and [
THROUGH
] and selectable range is [
] is not available.
R06
]to [00]
ENGLISH
21

DISPLAY SETTINGS

1 Press and hold . 2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press
DISPLAY
DIMMER
Selects the display and button illumination adjusted in the [ setting.
OFF
:Selects the day adjustments.; ON:Selects the night adjustments.;
DIMMER TIME
Turn the volume knob to adjust the [ Turn the volume knob to adjust the [ (Default: [ [
AUTO
:Changes between the day and night adjustments when you turn off or
on the car headlights. *
:Adjusts the dimmer on and off time.
ON OFF
ON
]: 18:00 or 6:00 PM
OFF
]: 6:00 or 6:00 AM)
1
] time, then press the knob.
.
Default:
BRIGHTNESS
] time, then press the knob.
XX
]
BRIGHTNESS
SCROLL
* *
*
1
The illumination control wire connection is required. (
2
Some characters or symbols will not be shown correctly (or will be blanked).
Sets the button, display and USB input terminal brightness for day and night separately.
1 DAY / NIGHT 2 3
2
ONCE
5-second intervals.;
Select a zone for setting. ( Set the brightness level (00 to 31). (Default:
:Scrolls the display information once.;
:Select day or night.
Illustration on left
OFF
:Cancels.
29
DAY:31
AUTO
)
)
;
NIGHT:15
:Repeats scrolling at
)
22
MORE INFORMATION
Playable files
• Playable audio file: MP3 (.mp3), WMA (.wma), AAC (.m4a), WAV(.wav), FLAC (.flac)
• Playable USB device file system: FAT12, FAT16, FAT32 Even when audio files comply with the standards listed above, playback may be impossible depending on the types or conditions of media or device.
About USB devices
• This unit can play MP3/WMA/AAC/WAV/FLAC files stored on a USB mass storage class device.
• You cannot connect a USB device via a USB hub.
• Connecting a cable whose total length is longer than 5m may result in abnormal playback.
• The maximum number of characters for:
- Folder names: 64 characters
- File names: 64 characters
- MP3 Tag: 64 characters
- WMA Tag: 64 characters
- AAC Tag: 64 characters
- WAV Tag: 64 characters
- FLAC Tag: 64 characters
• This unit can recognize a total of 20 480 files, 999 folders (999 files per folder including folder without unsupported files), and of 8 hierarchies.
• This unit cannot recognize a USB device whose rating is other than 5V and exceeds 1A.
About iPod/iPhone
Made for
- iPod touch (2nd, 3rd, 4th, and 5th generation)
- iPod classic
- iPod nano (3rd, 4th, 5th, 6th, and 7th generation)
- iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C
• It is not possible to browse video files on the “Videos” menu in
• The song order displayed on the selection menu of this unit may differ from that of the iPod/ iPhone.
• If some operations are not performed correctly or as intended, visit: <http://www.jvc.net/cs/car/>.
[HEAD MODE]
.
About Android device
• This unit supports Android OS 4.1 and above.
• Some Android devices (with OS4.1 and above) may not fully support Android Open Accessory (AOA)2.0.
• If the Android device supports both mass storage class device and AOA2.0, this unit always playback via AOA2.0 as priority.
• For more information and the latest compatible list, see: <http://www.jvc.net/cs/car/>.
About Pandora
• Pandora is available only in the U.S., Australia and New Zealand.
• Because Pandora is a third-party service, the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired, or some or all of the services may become unavailable.
• Some functions of Pandora cannot be operated from this unit.
• For issues using the application, please contact Pandora at pandora-support@pandora.com.
About iHeartRadio
• iHeartRadio® is a third-party service, therefore the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable.
• Some iHeartRadio® functionality cannot be operated from this unit.
About Bluetooth
• Depending on the Bluetooth version of the device, some Bluetooth devices may not be able to connect to this unit.
• This unit may not work with some Bluetooth devices.
• Signal conditions vary, depending on the surroundings.
• For more information about Bluetooth, visit the following JVC website: <http://www.jvc.net/cs/car/>.
ENGLISH
23
MORE INFORMATION

TROUBLESHOOTING

About JVC Playlist Creator and JVC Music Control
• This unit supports the PC application JVC Playlist Creator and AndroidTM application JVC Music Control.
• When you play audio file with song data added using the JVC Playlist Creator or JVC Music Control, you can search for audio file by Genres, Artists, Albums, Playlists, and Songs.
• JVC Playlist Creator and JVC Music Control are available from the following web site: <http://www.jvc.net/cs/car/>.
Change the display information
Press repeatedly.
FM
or
AM
USB
USB-IPOD USB-ANDROID
Station name (PS)*1 Frequency Program type (PTY)*1*2
1*2
Title*
* *
Day/Clock (back to the beginning)
1
For FM Radio Broadcast Data System stations only.
2
If unavailable, “NO PTY” / “NO TEXT” appears.
Playing time Day/Clock Album title/Artist*3 Track title*3 Folder/file name
3
*
If not recorded, “NO NAME” appears.
(back to the beginning)
Playing time Day/Clock Album title/Artist*4 Track title*4 (back to the beginning)
4
*
If not recorded, “NO NAME” appears.
Symptom Remedy
Sound cannot be heard. • Adjust the volume to the optimum level.
• Check the cords and connections.
“MISWIRING CHECK WIRING THEN PWR ON” appears.
General
“PROTECTING SEND SERVICE” appears.
Source cannot be selected. Check the [
• Radio reception is poor.
• Static noise while listening
Radio
to the radio.
Playback order is not as intended.
Elapsed playing time is not correct.
“NOT SUPPORT” appears and file skips.
Turn the power off, then check to be sure the terminals
of the speaker wires are insulated properly. Turn the power on again.
Send the unit to the nearest service center.
SRCSELECT
] setting. (4)
• Connect the antenna firmly.
• Pull the antenna out all the way.
The playback order is determined by the file name
(USB).
This depends on the recording process earlier.
Check whether the file is a playable format. (
23
)
PANDORA
IHEART
SiriusXM
AUX
BT AUDIO
24
Station name Album title/Artist Track title Playing time Day/ Clock
(back to the beginning)
Station name Track title*5 Track Artist*5 Day/Clock (back to the beginning)
5
*
If unavailable, station name appears.
Channel no./Channel name B Artist B Song title B Content information
B
Category name B Day/Clock B (back to the beginning)
AUX Day/Clock
Playing time Day/Clock Album title/Artist*6 Track title*6 (back to the beginning)
6
*
If not recorded, “UNKNOWN” appears.
“READING” keeps flashing. • Do not use too many hierarchical levels and folders.
• Reattach the USB device.
“CANNOT PLAY” flashes and/
USB / iPod
or connected device cannot be detected.
• Check whether the connected device is compatible with this unit and ensure the files are in supported formats.
( 23)
• Reattach the device.
The iPod/iPhone does not turn on or does not work.
• Check the connection between this unit and iPod/ iPhone.
• Detach and reset the iPod/iPhone using hard reset.
Correct characters are not displayed.
This unit can only display uppercase letters, numbers,
and a limited number of symbols.
TROUBLESHOOTING
Symptom
• Sound cannot be heard during playback.
• Sound output only from the Android device.
Cannot playback at
AUTO MODE
[
ANDROID
“NO DEVICE” or “READING” keeps flashing.
Playback is intermittent or sound skips.
“CANNOT PLAY” • Make sure Android device contains playable audio files.
“ADDERROR” “SEARCHERR”
“CHKDEVICE” Check the Pandora application on your device.
“NOSKIPS” The skip limit has been reached.
Pandora
“NOSTATIONS” No stations are found.
“STATIONLMT” The number of registered stations has reached its limit.
].
Remedy
• Reconnect the Android device.
AUDIO MODE
• If in [ on the Android device and start playback.
AUDIO MODE
• If in [ application or use another media player application.
• Restart the Android device.
• If this does not solve the problem, the connected Android device is unable to route the audio signal to unit. (
• Make sure JVC MUSIC PLAY APP is installed on the Android device. (5)
• Reconnect the Android device and select the appropriate control mode. (
• If this does not solve the problem, the connected Android device does not support [
• Switch off the developer options on the Android device.
• Reconnect the Android device.
• If this does not solve the problem, the connected Android device does not support [
Turn off the power saving mode on the Android device.
• Reconnect the Android device.
• Restart the Android device.
New station creation is unsuccessful.
Retry after deleting unnecessary stations from your device.
], launch any media player application
], relaunch the current media player
6
)
AUTO MODE
AUTO MODE
]. (
]. (
23
23
Symptom Remedy
“UPGRADEAPP” Make sure you have installed the latest version of the
Pandora application on your device.
“CONNECT ERR” Communication is unstable.
“RATING ERR” Registration of thumbs up/thumbs down has failed.
Pandora
“LICENSE ERR” You try to access from a country which Pandora is not
23
)
Station cannot be selected. If “Explicit Content” in [Account Settings] is checked in
“CREATE ERR” Custom station name creation is unsuccessful.
)
)
“SAVE ERROR” Addition to the favorite category failed.
“DISCONNCTED” Check the connection to the device.
“NOSKIPS” The skip limit has been reached. Retry later.
“NOSTATIONS” No stations are found.
“NOT CONNCTD” Link to the application is impossible.
“UPDATE APP” Make sure you have installed the latest version of the
iHeartRadio
“PLS LOGIN” You haven’t log in. Log in again.
“STATION NOT AVAILABLE” Broadcast from the station is over.
“STATION NOT SELECTED” No station is selected.
“STREAM ERR” Broadcast data is interrupted.
“THUMBS ERR” Registration of Thumbs Up/Down has failed.
“TIMED OUT” The request has resulted in time-out.
deliverable.
the web version of iHeartRADIO, custom stations become unavailable.
iHeart Link for JVC application on your device.
ENGLISH
25
TROUBLESHOOTING
Symptom Remedy
“CHLOCKED LOCK CODE?”
“CHANUNSUB” The selected channel is unsubscribed.
“CHUNAVAIL” The selected channel is unavailable. Visit
“CHKANTENNA” Check the antenna and its connection are in good condition. “CHECKTUNER” Make sure the SiriusXM Vehicle Tuner is connected to the
SiriusXM® Radio
“NOSIGNAL” Make sure the antenna is mounted outside the vehicle. “SUBSCRIPTION
UPDATED – PRESS ENTER TO CONTINUE.”
“CODE ERROR” Make sure you have entered the correct pass code. “NO CONTENT” There is insufficient content to start TuneScan. “SCAN CANCEL” TuneScan has been aborted. No Bluetooth device is
detected. Pairing cannot be
made.
The selected channel is locked. Enter the correct pass code
to unlock.
Call 1-866-635-2349 in U.S.A. or 1-877-438-9677 in Canada
to subscribe.
www.siriusxm.com for more information about the SiriusXM channel lineup.
unit.
Your subscription is updated. Press the volume knob to
continue.
• Search from the Bluetooth device again.
• Reset the unit.
• Make sure you have entered the same PIN code to both the unit and Bluetooth device.
• Delete pairing information from both the unit and the Bluetooth device, then perform pairing again.
( 13)
( 3)
( 13)
( 14)
Symptom Remedy
Sound is being interrupted or skipped during playback of a Bluetooth audio player.
The connected Bluetooth audio player cannot be controlled.
“PAIRING FULL” The number of registered devices has reached its limit.
“PLEASE WAIT” The unit is preparing to use the Bluetooth function. If the
Bluetooth®
“BT DEVICE NOT FOUND” The unit failed to search for the registered Bluetooth
“NOT SUPPORT” The connected phone does not support Voice Recognition
“ERROR” Try the operation again. If “ERROR” appears again, check
“H/W ERROR”
“BT ERROR PLS UPDATE” Update the Bluetooth firmware.
• Reduce the distance between the unit and the Bluetooth audio player.
• Turn off, then turn on the unit and try to connect again.
• Other Bluetooth devices might be trying to connect to the unit.
• Check whether the connected Bluetooth audio player supports Audio/Video Remote Control Profile (AVRCP). (Refer to the instructions of your audio player.)
• Disconnect and connect the Bluetooth player again.
Retry after deleting an unnecessary device.
DELETE PAIR)
message does not disappear, turn off and turn on the unit, then connect the device again.
devices during your device and connect manually.
feature.
if the device supports the function you have tried.
Reset the unit and try the operation again. If “H/W
ERROR” appears again, consult your nearest service center.
[AUTO CNNCT]
. Turn on Bluetooth from
( 18)
( 4)
( 18,
Echo or noise occurs. • Adjust the microphone unit’s position.
Bluetooth®
Phone sound quality is poor.
• Check the
• Reduce the distance between the unit and the Bluetooth device.
• Move the car to a place where you can get a better signal reception.
[ECHO CANCEL]
26
setting.
( 14)
( 15)
If you have any troubles, try the following:
1 Check TROUBLESHOOTING 2 Reset the unit (
3) 3 Contact (USA only) Call: 1-800-252-5722 ( or ) visit: http://www.jvc.com
SPECIFICATIONS
FM Frequency Range 87.9MHz — 107.9MHz (200kHz step)
87.5MHz — 108.0MHz (50kHz step) Channel Space Selection 50kHz/200kHz Usable Sensitivity (S/N=26dB) 8.2dBf (0.71μV/75Ω) Quieting Sensitivity (DINS/N=46dB) 17.2dBf (2.0μV/75Ω) Frequency Response (±3dB) 30Hz — 15kHz Signal-to-Noise Ratio (MONO) 64dB
Tuner
Stereo Separation (1kHz) 40dB
AM Frequency Range 530kHz — 1700kHz (10kHz step)
531kHz — 1611kHz (9kHz step) Channel Space Selection 9kHz/10kHz Usable Sensitivity (S/N=20dB) 29dBμ (28.2μV)
USB Standard USB1.1, USB2.0 (Full speed) Compatible Devices Mass storage class File System FAT12/16/32 Maximum Supply Current DC5V D/A Converter 24 Bit Frequency Response (±1dB) 20Hz — 20kHz Signal-to-Noise Ratio (1kHz) 105dB Dynamic Range 88dB
USB
Channel Separation 90dB MP3 Decode Compliant with MPEG-1/2 Audio Layer-3 WMA Decode Compliant with Windows Media Audio AAC Decode AAC-LC “.m4a” files WAV Decode RIFF waveform Audio Format (Linear
PCM only)
FLAC Decode FLAC files
1A
Frequency Response (±3dB) 20Hz—20kHz Input Maximum Voltage 1000mV
Auxiliary
Input Impedance 30kΩ
Version Bluetooth Ver.2.1+EDR/ Bluetooth 3.0 Frequency Range 2.402 GHz — 2.480 GHz Output Power +4 dBm (MAX), 0 dBm (AVE) Power Class 2 Maximum Communication Range Line of sight approx. 10 m (32.8 ft) Pairing SSP (Secure Simple Pairing) Profile HFP1.6 (Hands-Free Profile)
Bluetooth
A2DP (Advanced Audio Distribution Profile) AVRCP1.4 (Audio/Video Remote Control Profile) PBAP (Phonebook Access Profile) SPP (Serial Port Profile)
Maximum Output Power 50W×4 or
50W×2 + 50W×1 (Subwoofer = 4Ω)
Full Bandwidth Power (at less than 1% THD)
Audio
Speaker Impedance 4Ω—8Ω Preout Level/Load (USB) 2500mV/10kΩ Preout Impedance ≤600Ω
Operating Voltage (10.5V—16V allowable)
Maximum Current Consumption 10A Operating Temperature Range 0°C to +40°C
General
Installation Size (W×H×D) 182mm×53mm×108mm
Weight
Subject to change without notice.
22W×4
14.4V
(7-3/16"×2-1/8"×4-5/16")
0.60k
g
(1.4lbs)
ENGLISH
27
Warning
• The unit can only be used with a 12V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit.
• Insulate unconnected wires with vinyl tape to prevent a short circuit.
• Be sure to ground this unit to the car’s chassis again after installation.
Caution
• For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
• Do not connect the (black), or connect them in parallel.
• Connect speakers with a maximum power of more than 50W. If the maximum power of the speakers is lower than 50W, change the
[AMPGAIN]
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red) to the terminal on the vehicle’s fuse box which provides
INSTALLATION / CONNECTION
12 V DC power supply and is turned on and off by the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.
• If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old fuse with one that has the same rating.
setting to avoid damaging the speakers. ( 21)
wires of speakers to the car chassis or Ground wire
Basic procedure 1
Remove the key from the ignition switch, then disconnect the
terminal of the car battery.
2 Connect the wires properly.
See Wiring connection. (
29)
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
4 Connect the terminal of the car battery. 5 Reset the unit. ( 
3
)
Installing the unit (in-dash mounting)
Hook on the top side
Orientate the trim plate as illustrated before fitting.
When installing without the mounting sleeve
Use only the specified screws. Using wrong screws
might damage the unit.
Flat or round head screws (not supplied) M5 × 8mm (M5 × 3/8")
Pocket
Bracket (not supplied)
Do the required wiring.
(29)
Dashboard of your car
Bend the appropriate tabs to hold the sleeve firmly in place.
How to remove the unit
28
Wiring connection
1
JVC Amplifier
MIC (Microphone input terminal)
( 14)
*
Fuse (10A)
Remote wire (not supplied)
Ignition switch
Signal cord (not supplied)
To the optional SiriusXM Vehicle Tuner (commercially available)
Join the same color wires together.
Blue/white: Remote (200mA max.)
Orange/white: Illumination
Yellow: Battery 12V
( 11)
Light blue/yellow
STEERING
WHEEL
REMOTE
Front output
Rear/subwoofer output
Antenna terminal
To the steering wheel remote control adapter
Recommended
Blue: To power antenna Blue/white: To amplifier
connection
(Not used)
1
*
Firmly connect the ground wire of
the amplifier to the car’s chassis to avoid damaging the unit.
Vehicle dashboard
Factory wiring harness (vehicle)
Vehicle-specific Wiring
Brown
Harness (separately purchased)
Part list for installation
(A)
Faceplate
(B)
Trim plate
(C)
Mounting sleeve
(D)
Wiring harness
Car fuse block
Separate red wire
Make this connection if your vehicle factory wiring harness does not have “12V ignition switch” wire.
2
*
You can also connect a
subwoofer speaker directly using this lead without an external subwoofer amplifier. For setting,
21.
Red: Ignition 12V
Black: Ground Gray: Front speaker (right) Gray/black White: Front speaker (left) White/black Purple: Rear speaker (right) Purple/black Green: Rear speaker (left) Green/black
2
*
For more information: Metra Electronics:
(E)
Extraction key
www.metraonline.com Scosche Industries: www.scosche.com
2
*
ENGLISH
29
libFLAC
Copyright (C) 2000,2001,2002,2003,2004,2005,2006,2007,2008,2009 Josh Coalson Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
- Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
- Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
- Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND ONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
• “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
• Lightning is a trademark of Apple Inc.
• Pandora, the Pandora logo, and the Pandora trade dress are trademarks or registered trademarks of Pandora Media, Inc., used with permission.
• iHeartRadio® is a registered mark of Clear Channel Broadcasting, Inc. in the United States and other countries. Such marks are used under license.
• Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights reserved.
• Android is trademark of Google Inc.
• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVC KENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners.
© 2014 JVC KENWOOD Corporation
0914DTSMDTJEIN
WHEN
IT
IS
NOT
REQUIRED
TO
PANEL USE
DETACH
FROM
THE
ATTACH
THE
MAIN
THE
FRONT
THE
PROVIDED
THE
CONTROL
UNIT.
CONTROL
MAIN
UNIT,
SGREWTO
PANEL
TO
GE4040
1-001 A
Loading...