JENN-AIR® DETAILED PLANNING DIMENSIONS |
|
1 of 4 |
|||
36" Gas Cooktop |
|
|
|
|
|
JGC8536BD – 36" x 45⁄8" x 213⁄4" |
|
|
|
|
|
PRODUCT DIMENSIONS |
|
|
|
|
|
A |
|
MODEL # |
JGC8536BD |
||
|
|
|
|
in |
cm |
|
|
A |
Overall width |
36 |
91.4 |
|
|
B |
Depth to corner of cooktop |
215⁄8 |
54.8 |
B |
C |
C |
Depth to center of cooktop |
213⁄4 |
55.2 |
|
D |
Center of cooktop to center of gas inlet |
151⁄2 |
39.4 |
|
|
|
||||
|
|
E |
Width of recessed cooktop |
343⁄8 |
87.3 |
|
|
F |
Height from gas inlet to countertop |
45⁄8 |
11.6 |
Top VIEW |
|
G |
Height of recessed cooktop |
33⁄4 |
9.6 |
|
|
H |
Height with grates |
1 |
2.4 |
|
|
I |
Center of gas inlet to recessed cooktop |
13⁄4 |
4.4 |
|
|
J |
Depth of recessed cooktop |
203⁄8 |
51.6 |
|
|
H |
|
|
|
F |
G |
|
|
|
|
D |
|
|
|
|
|
E |
|
|
|
|
|
FRONT VIEW |
|
|
|
|
|
B
I
J
Side VIEW
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing |
JRC120032A 07/2012 |
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary. |
JENN-AIR® DETAILED PLANNING DIMENSIONS |
2 of 4 |
36" Gas Cooktop
JGC8536BD – 36" x 45⁄8" x 213⁄4"
OPENING/CLEARANCE DIMENSIONS
A |
C* |
|
D |
B |
B |
E |
|
e |
g |
FRONT VIEW
MODEL # |
JGC8536BD |
|||
|
|
in |
cm |
|
A |
Width of combustible area above |
36 |
91.4 |
|
cooking surface (min.) |
||||
|
|
|
||
B |
Width from cooktop to fixed wall |
8 |
20.3 |
|
or other combustible material (min.) |
||||
|
|
|
||
C* |
Height to bottom of uncovered wood or |
30 |
76.2 |
|
metal cabinet above cooking surface (min.) |
||||
D |
Height to bottom of uncovered wood |
18 |
45.7 |
|
or metal cabinet (min.) |
||||
|
|
|
||
E |
Height to top edge of electrical and gas |
37⁄8 |
9.7 |
|
installation area |
||||
|
|
|
||
F |
Depth of upper cabinet (recommended) |
13 |
33.0 |
|
G |
Depth from cutout to wall (min.) |
3⁄4 |
1.9 |
|
H |
Width of cutout |
347⁄8 |
88.6 |
|
I |
Depth of cutout |
207⁄8 |
52.9 |
|
J |
Depth from cutout to front of |
2 |
5.1 |
|
countertop (min.) |
||||
|
|
|
||
e |
Recommended electrical access location |
|
|
|
g |
Recommended gas supply line location |
|
|
*Dimension can be reduced by 6" (15.2 cm) when bottom of wood or metal cabinet is covered by not less than 1⁄4" (0.6 cm) flame retardant millboard covered with not less than No. 28 MSG sheet metal, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
If installing a hood or microwave hood combination above the cooktop, follow the hood or microwave hood combination instructions for dimensional clearances above the cooking surface.
GAS REQUIREMENTS
Side
Cabinet
F
G
Natural Gas
This cooktop is factory-set for use with natural gas.
LP Gas Conversion
Conversion must be done by a qualified service technician. To convert to LP gas, use the LP gas conversion kit provided with the cooktop.
ELECTRICAL REQUIREMENTS
120 volt, 60 Hz, AC only, 20-amp fused, grounded circuit is required.
A time-delay fuse or dedicated circuit is recommended. Minimum power cord length is 46" (117.0 cm).
LOCATION REQUIREMENTS
•To ensure cooktop base clearance, cabinet side walls need to be wider than the cutout.
•If cabinet has a drawer, allow a 4" (10.2 cm) minimum clearance between countertop and top of drawer. Drawer depth may need to be shortened to avoid interfering with the regulator.
COOKTOP OVER SINGLE WALL OVEN INSTALLATION
REQUIREMENTS
•For approved model number combinations, refer to the under counter label on the bottom of the cooktop burner box.
•To install a cooktop over a 30" single wall oven, refer to page 3.
H G
I
J
Side VIEW |
TOP VIEW – cutout |
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
JRC120032A 07/2012