Jenn-Air JFI2089WTS2, JFI2089WTS1, JFI2089WTS0, JFI2089WES2, JFI2089WES1 Owner’s Manual

...

0 (0)

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,

please visit our website at www.jennair.com for additional information. If you still need assistance, call us at 1-800-536-6247. In

Canada, visit our website at www.jennair.ca or call us at 1-800-807-6777.

You will need your model and serial number, located on the inside wall of the refrigerator compartment.

Para obtener acceso a "lnstrucciones para el usuario del refrigerador" en espa_ol, o para obtener informaci6n adicional acerca de

su producto, visite: www.jennair.com.

Necesitara su nQmero de modelo y de serie, ubicado en el interior del compartimiento del refrigerador.

TableofContents/Tabledes mati6res

REFRIGERATOR SAFETY ..................................................................... 1

INSTALLATION INSTRUCTIONS ......................................................... 2

REFRIGERATOR USE ........................................................................... 8

REFRIGERATOR CARE ....................................................................... 12

TROUBLESHOOTING .......................................................................... 13

WATER FILTER CERTIFICATIONS .................................................... 15

PRODUCT DATA SHEETS .................................................................. 16

WARRANTY .......................................................................................... 18

SI_CURITI_ DU RI_FRIGI_RATEUR ..................................................... 20

INSTRUCTIONS D'INSTALLATION ................................................... 21

UTILISATION DU RC:FRIGC:RATEUR ................................................. 27

ENTRETIEN DU RI_FRIGI_RATEUR ................................................... 32

DI_PANNAGE ........................................................................................ 33

FEUlLLES DE DONNI_ES SUR LE PRODUlT .................................... 36

GARANTIE ............................................................................................ 38

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

W10275994A

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

• Do not hit the refrigerator glass doors (on some models).

SAVE THESE INSTRUCTIONS

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Takeoff the doors.

• Leave the shelves in place so that children may not easily

climb inside.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

"walk" the refrigerator when trying to move it, as floor

damage could occur.

Remove the Packaging

Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

• Dispose of/recycle all packaging materials.

Clean Before Using

After you remove all of the packaging materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

"Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for 1/2"

(1.25 cm) of space on each side and at the top. Allow for 1"

(2.54 cm) of space behind the refrigerator. If your refrigerator has

an ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 23/4''(7.0 cm) minimum space between the refrigerator and

wall to allow the door to swing open.

NOTE: It is recommended that you do not install the refrigerator

near an oven, radiator, or other heat source. Do not install the

refrigerator in a location where the temperature will fall below 55°F

(13°C).

r!!

1/2"(1.25 cm) /

][

2s/4" (7.0 cm)

/ _ _: _ _, 4/

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator or

Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source and

reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting. See "Using the

Controls."

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • 1A"Nut driver

• 7/16"and 1/2"Open-end or two • 1A"Drill bit

adjustable wrenches • Cordless drill

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Do not use a piercing-type or 346"(4.76 mm) saddle valve

which reduces water flow and clogs more easily.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

• For models with water filters, the disposable water filter

should be replaced at least every 6 months.

• Turn off the icemaker if water supply is not connected. See

"Ice Maker and Ice Storage Bin."

Wa_rPmssum

A cold water supply with water pressure of between 35 and

120 psi (241 and 827 kPa) is required to operate the water

dispenser and ice maker. Ifyou have questions about your water

pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water Filtration

System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

, ,, _J _.,_,_ _j

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is

connected, turn the ice maker OFF.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Find a V2"to 1V4" (12.7 mm to 31.8 mm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure

from the connection on the rear of the refrigerator to the water

pipe. Add 7 ft (2.1 m) to allow for cleaning. Use V4"(6.35 mm)

O.D. (outside diameter) copper tubing. Be sure both ends of

copper tubing are cut square.

5. Using a cordless drill, drill a V4"hole in the cold water pipe you

have selected.

A. Cold waterpipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly inthe V4"drilled hole in

the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws slowly

and evenly so the washer makes a watertight seal. Do not

overtighten.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten or

you may crush the copper tubing.

8. Place the free end of the tubing in a container or sink, and turn

ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe.

Connect to Refrigerator

Depending on your model, the water line may come down from

the top or up from the bottom. Follow the connection instructions

for your model.

Style 1

1. Remove the plastic cap from water supply connection. Place

brass nut and compression sleeve on copper tube end as

shown.

2. Placeendofthecoppertubingintotheplasticwatervalve

supplyline.Slidethebrassnutoverthesleeveandscrewthe

nutintosupplyline.

3. Usinganadjustablewrench,holdthenutontheplasticwater

linetokeepitfrommoving.Then,withasecondwrenchturn

thenutonthecoppertubingcounterclockwisetocompletely

tighten.Donotovertighten.

4. Checkconnectionbypullingonthecoppertubing.

5. Fastentheplasticwaterlinetotherefrigeratorwitha"P"

clamp.Slidetheplasticwaterlineintotheretainer.

Using an adjustable wrench, hold the nut on the plastic water

line to keep it from moving. Then, with a second wrench turn

the compression nut on the copper tubing counterclockwise

to completely tighten. Do not overtighten.

A. "P" clamp

B.Plastic water fine

C. Water valve inlet port

D. Compression nut

E.Copper tubing

Check connection by pulling on copper tubing. Attach the

plastic water line to the refrigerator cabinet with a "P" clamp.

Turn on water supply to the refrigerator and check for leaks.

Correct any leaks.

Complete the Installation

A. Brass nut C. "P" Clamp

B. Compression sleeve

6. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

Style 2

1. Create a service loop (minimum diameter of 2 ft [61 cm]) with

the copper tubing. Avoid kinks when coiling the copper

tubing.

2. Remove the plastic cap from water valve inlet port. Place a

compression nut and sleeve on the copper tubing.

3. Insert the end of the copper tubing into the water valve inlet

port. Shape tubing slightly so that the tubing feeds straight

into the port to avoid kinks.

4. Slide the compression nut over the sleeve and screw into the

water valve inlet port.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely

fill the ice container.

A. Plastic water tubing C. Compression nut

B. Sleeve D. Copper tubing

_@@i_¢_V '_¸ _ ..... _H_

All graphics referenced in the following instructions are included

later in this section after "Final Steps."

Remove and Replace Handles

1. Using a3/32"or 1/8"Allen wrench, loosen the two setscrews

located on the side of each handle. See Metal Handle

graphics 1 and 2.

2. Pull the handle straight out from the door. Make sure you keep

the screws for reattaching the handles.

3. To replace the handles, reverse the directions.

Remove Doors and Hinges

IMPORTAN1"."

• Remove food and any adjustable door or utility bins from

doors.

• Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

TOOLS NEEDED: %d', 3/8",1/4"hex head socket wrench,

#2 Phillips screwdriver, and a flat-blade screwdriver.

1. Unplug refrigerator or disconnect power.

2. Remove the base grille. Grasp the grille firmly and pull it

toward you.

3. Starting with the right-hand side door, remove the parts for the

top hinge as shown inTop Hinge graphic. Lift the refrigerator

door from the bottom hinge pin.

4. Remove the shim from the bottom hinge pin and keep it for

later use. See Bottom Hinge graphic.

5. Remove top hinge cover from left side refrigerator door.

Disconnect the wiring plug located on top of the hinge by

wedging a flat-blade screwdriver or your fingernail between

the two sections. See Connections graphic.

6. Disconnect the water line by holding the tabbed section of the

water line while turning the black locking collar clockwise. See

Connections graphic.

7. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the left-hand side door from the bottom hinge pin.

NOTE: On some models, remove the shim from the bottom

hinge pin and keep it for later use. See Bottom Hinge graphic.

Using a 3/8"hex wrench, remove the leveling leg brackets from

the bottom of the cabinet. Keep screws for later use.

Replace Doors and Hinges

Align the door so that the bottom of the refrigerator door

aligns evenly with the top of the freezer drawer. Tighten all

screws.

4. Reconnect the wiring plug on top of the left-hand side

refrigerator door.

5. Reconnect the water lines by firmly pushing one line inside the

other. Slide the black locking collar fully forward.

6. While holding the tabbed section of the waterline, turn the

locking collar counterclockwise until you hear a "click."

NOTE: The arrow on the tabbed section should align with the

two bars on the locking collar.

7. Check for leaks. Replace the top hinge covers.

Remove and Replace Freezer Drawer

IMPORTANT: Two people may be required to remove and replace

the freezer drawer. Graphics are included later in this section.

Remove Drawer Front

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the

drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in

the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front

Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the freezer compartment. Insert

the screws in the top of the drawer front into the slots in the

drawer brackets. See Drawer Front Replacement graphic.

2. Pull the drawer brackets toward you to position the two

screws in the bottom of the drawer front into the brackets.

See Drawer Front Replacement graphic.

3. Completely tighten the four screws.

Final Steps

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Assemble the parts for the top hinge as shown in Top Hinge

graphic. Do not tighten the screws completely.

Replace the parts for the bottom hinge as shown in Bottom

Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door

while the hinges are being moved. Do not depend on the door

gasket magnets to hold the door in place while you are

working.

1. Plug into a grounded 3 prong outlet.

2. Return all removable parts to doors and drawer and food to

refrigerator and freezer.

A, Hinge Cover Screw

B, Top Hinge Cover

C, 5/18" Hex-Head Hinge Screws

D. Top Hinge

Bottom Hinges

A, Shim (on some models)

B, Bottom Hinge

C. Hinge Screws

Connections

A _ _ B

A. Tabs

B, Wiring Plug

} }

Metal Handle

A. 3/32"or 1/8"Setscrew

Metal Handle @

A, 3/32"or 1/8"Setscrew

A, Loosen 4 Door Bracket Screws

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Depending on your model, your refrigerator may have two

adjustable rollers (Style 1) or two leveler foot screws (Style 2)

located at the base of the refrigerator. If your refrigerator seems

unsteady or you want the door to close more easily, use the

instructions below.

1. Remove the base grille. Grasp the grille firmly and pull it

toward you.

2. Raise or lower the cabinet.

Style 1 - Front leveling

Using a 3/8"hex driver, turn the roller adjustment screw(s) on

each side to raise or lower that side of the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the adjustment screws and

rollers. This makes it easier to turn the screws. It may take

several turns of the roller adjustment screw to adjust the tilt of

the refrigerator.

• To raise, turn the roller adjustment screw to the right.

• To lower, turn the roller adjustment screw to the left.

Turn the brake foot clockwise until it is firmly against the floor

to keep the refrigerator from rolling forward when the freezer

drawer is pulled open.

A. Front roller adjustment screw

B. Brake foot

Style 2 - Leveler screw

Using a 1/4"hex driver, turn the leveling screw on each side to

raise or lower that side of the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws. This

makes it easier to turn the screws. It may take several turns of

the leveling screw to adjust the tilt of the refrigerator.

• To raise, turn the leveling screw clockwise.

• To lower, turn the leveling screw counterclockwise.

A. Levering screw

Open the door again to make sure that it closes as easily as

you like. If not, tilt the refrigerator slightly more to the rear by

turning both leveling screws clockwise. It may take several

more turns, and you should turn both screws the same

amount.

4. Replace the base grille.

REFRIGERATORUSE

_Jpe _ g Doo_s

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

A. Hinged seal

IMPORTANT:

• The control panel is located on the front of the ice and water

dispenser.

To access the main control menu, press any of the four touch

pads located on either side of the display. Then, touch the pad

next to the desired option or user setting to access the various

features.

NOTE: Press only the touch pads next to your selection on the

display screen, not the selection itself.

Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has cooled

completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature

controls to a colder than recommended setting will not cool

the compartments any faster.

The recommended settings should be correct for normal

household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream is

firm.

If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

A. Touch pads

Temperature Controls

For your convenience, your temperature controls are preset at the

factory. When you first install your refrigerator, make sure the

controls are still set to the recommended set points.

• Press the touch pad next to "FRESH FOOD TEMP" on the

main menu to display the current set point of the

compartment. Press the touch pad next to "WARMER" or

"COLDER" to adjust the set point to the recommended 38°E

Press the touch pad next to "Done" to lock in the setting.

Press the touch pad next to "FREEZER TEMP" on the main

menu to display the current set point of the compartment.

Press the touch pad next to "WARMER" or "COLDER" to

adjust the set point to the recommended 0°E Press the touch

pad next to "Done" to lock in the setting.

To Turn Cooling Off/On:

Cooling On/Off controls all cooling functions, the control panel

and the dispenser. It does not disconnect power to the

refrigerator.

• Press and hold the On/Off button for three seconds. The LED

will light up to indicate that cooling is Off. Neither

compartment will cool.

• Press the On/Off button again to turn on the cooling. The LED

will turn off.

[]

Cooling

holcl 3 sec

Adjusting Controls

The FRESH FOOD TEMP control adjusts the refrigerator

compartment temperature. The FREEZER TEMP control adjusts

the freezer compartment temperature.

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the chart as a

guide.

To Adjust Set Point Temperatures:

The display will show the set point for approximately 3 seconds.

• Press the touch pad next to "WARMER" or "COLDER" to

adjust the set point to the desired temperature. Then, press

the touch pad next to "Done" to lock in the new set point

temperature.

NOTE: Except when first turning on the refrigerator, do not adjust

either temperature control more than one setting at a time. Wait

24 hours for the temperature to stabilize between adjustments.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm FRESH FOOD Control

1° lower

FREEZER too warm/too little ice FREEZER Control

1° lower

REFRIGERATOR too cold FRESH FOOD Control

1° higher

FREEZER too cold FREEZER Control

1° higher

Options

Door Alarm

The Door Alarm feature sounds an audible alarm every few

seconds when the either refrigerator door has been left open for

3 continuous minutes. The alarm will sound until the door is

closed or Door Alarm is turned off.

On the main menu, press the touch pad next to "Options."

Press the touch pad next to "Door Alarm Is On" to switch

between ON and OFE Press the touch pad next to "Done" to

lock in the desired setting and return to the main menu.

Humidity Control (on some models)

The humidity control feature turns on a heater to help reduce

moisture on the door hinge seal. Use in humid environments or

when you notice moisture on the door hinge seal. The refrigerator

uses more energy when Humidity Control is on.

1. On the main menu, press the touch pad next to "Options."

2. Press the touch pad next to "Humid Ctrl Is On" to switch

between ON and OFE Press the touch pad next to "Done" to

lock in the desired setting and return to the main menu.

Vacation Mode

The vacation mode feature decreases the number of automatic

defrost cycles. Once set, vacation mode will remain on until a

door is opened or the feature is turned off on the control panel.

NOTE: Door openings are ignored for the first hour after Vacation

mode is activated.

1. On the main menu, press the touch pad next to "Options."

2. In each of the following screens, continue to press the touch

pad next to "More Options" until "Vac. Mode is Off" appears

on the display.

3. Press the touch pad next to "Vac. Mode is Off" to switch

between ON and OFE Press the touch pad next to "Done" to

lock in the desired setting and return to the main menu.

Max Cool

The Max Cool feature assists with periods of high refrigerator or

freezer use, full grocery loads, or temporarily warm room

temperatures by lowering the freezer and refrigerator to the

minimum temperatures.

1. On the main menu, press the touch pad next to "Options."

2. In each of the following screens, continue to press the touch

pad next to "More Options" until "Max Cool is Off" appears on

the display.

Press the touch pad next to "Max Cool is Off" to switch

between ON and OFF. Press the touch pad next to "Done" to

lock in the desired setting and return to the main menu.

NOTE: The Max Cool feature will automatically shut off in

approximately 2 hours.

Sabbath Mode

The Sabbath mode feature turns off all lights, disables the water

and ice dispenser, disables all alarms and tones, disables the

automatic defrost feature and disables the control panel.

While the refrigerator is operating in Sabbath mode, any touch of

the control panel will display the Sabbath mode control which will

allow you to turn off the Sabbath mode feature.

Turn Sabbath mode on:

1. On the main menu, press the touch pad next to "Options."

2. In each of the following screens, continue to press the touch

pad next to "More Options" until "Sabbath Is Off" appears on

the display.

3. Press the touch pad next to "Sabbath Is Off" to switch

between ON and OFF. Press the touch pad next to "Done" to

lock in the desired setting and return to the main menu.

Temp Alarm

The TempAlarm feature alerts you if the temperature exceeds

normal operating temperatures, for an hour or longer, in either or

both the refrigerator and freezer compartments. An audible alarm

will sound repeatedly and the highest temperature reached in

each compartment will be displayed.

NOTE: Touch any pad on the control panel to turn off the audible

alarm. Temp Alarm will automatically reset once the warm

condition has been corrected for 30 minutes.

1. On the main menu, press the touch pad next to "Options."

2. In each of the following screens, continue to press the touch

pad next to "More Options" until "Temp Alarm Is Off" appears

on the display.

3. Press the touch pad next to "Temp Alarm Is Off" to switch

between ON and OFF. Press the touch pad next to "Done" to

lock in the desired setting and return to the main menu.

Replace H20 Filter

See "Water FiltrationSystem."

User Settings

The control center allows you to set user preferences, if desired.

Language

The language preference allows you to change the control panel

display to English, French or Spanish.

1. On the main menu, press the touch pad next to "User

Settings."

2. Press the touch pad next to "Select Language."

3. Press the touch pad next to either "Mettre En Frangais" or

"Cambiar En Espa_ol." Press the touch pad next to "Confirm"

to lock in the setting and return to the main menu.

Temperature Display

The temperature display preference allows you to change the

control panel display from degrees Fahrenheit to degrees Celsius.

1. On the main menu, press the touch pad next to "User

Settings."

2. Press the touch pad next to "Fahrenheit Is On" to switch

between Fahrenheit and Celsius. Press the touch pad next to

"Done" to lock in the desired setting and return to the main

menu.

Display Brightness

The Display Brightness preference adjusts the backlight level of

the control panel.

1. On the main menu, press the touch pad next to "User

Settings."

2. In each of the following screens, continue to press the touch

pad next to "More Settings" until "Display Brightness"

appears on the display.

3. Press the touch pad next to "Lighter" or "Darker" to adjust the

setting between 1 (darkest) and 5 (lightest). Press the touch

pad next to "Done" to lock in the desired setting and return to

the main menu.

Adjust Light Sensor

The "Adjust LiteSensor" preference allows you to adjust the level

at which the Light Sensor will detect darkness and activate the

Auto On mode for the dispenser light.

1. On the main menu, press the touch pad next to "User

Settings."

2. In each of the following screens, continue to press the touch

pad next to "More Settings" until "Adjust LiteSensor" appears

on the display.

3. Press the touch pad next to "Lighter" or "Darker" to adjust the

setting between 1 (darkest) and 9 (lightest). Press the touch

pad next to "Done" to lock in the desired setting.

Alarm Sound

The alarm sound preference allows you to turn off any audible

alarms (door open, too warm etc.) when quick and simple

remedies are not possible. It will not disable alarm features or

visual displays.

1. On the main menu, press the touch pad next to "User

Settings."

2. In each of the following screens, continue to press the touch

pad next to "More Settings" until "Alrm Sound Is On" appears

on the display.

3. Press the touch pad next to "Alrm Sound Is On" to switch

between ON and OFF. Press the touch pad next to "Done" to

lock in the desired setting and return to the main menu.

You can control the amount of humidity in the moisture-sealed

crisper. Depending on your model, adjust the control to any

setting between FRUIT and VEGETABLES or LOW and HIGH.

FRUIT / LOW (open) for best storage of fruits and vegetables with

skins.

VEGETABLES / HIGH (closed) for best storage of fresh, leafy

vegetables.

The ice maker and storage bin are located in the upper left-hand

side of the refrigerator compartment.

Turning the Ice Maker On/Off

The On/Oft switch is located on the ice maker.

Toturn on the ice maker, press the switch to the ON position.

To manually turn off the ice maker, press the switch to the OFF

position.

NOTE: Your ice maker has an automatic shutoff. The ice maker

sensors will automatically stop ice production, but the control will

remain in the ON position.

Removing and Replacing Ice Storage Bin

To Remove the Ice Storage Bin:

1. Hold the base of the storage bin and press the release button

on the lower right.

2. Pull the storage bin out until resistance is felt. Lift up the front

of the ice bin and remove.

3. Press the switch to the OFF position

To Replace the Ice Storage Bin:

IMPORTANT: It may be necessary to turn the auger driver, behind

the ice bin, counterclockwise to properly align the ice bin with the

auger driver. The ice storage bin must be locked in place for

proper ice dispensing.

1. Press the switch to the ON position

2. Slide the ice bin into the guide rails located on either side of

the enclosure.

3. Push the ice bin in until resistance is felt. Raise the front

slightly and push the ice bin in until an audible "click" is heard.

_____ ..............AII

A. ON position

B. Auger driver

Ice Production Rate

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

• The ice maker should produce approximately 8 to 12 batches

of ice in a 24-hour period.

• To increase ice production, lower the freezer and refrigerator

temperature. See "Using the Controls." Wait 24 hours

between adjustments.

Remember

The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If asoftened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

Do not use anything sharp to break up the ice in the bin. This

can cause damage to the ice bin and dispenser mechanism.

Do not store anything on top of the ice maker or in the ice

storage bin.

IMPORTANT:

After connecting the refrigerator to a water source, flush the

water system. Press the Water button on the control panel.

Use a sturdy container to depress and hold the dispenser

lever for 5 seconds, then release it for 5 seconds. Repeat until

water begins to flow. Once water begins to flow, continue

depressing and releasing the dispenser lever (5 seconds on,

5 seconds off) for an additional 2 minutes. This will flush air

from the filter and water dispensing system. Additional

flushing may be required in some households. As air is cleared

from the system, water may spurt out of the dispenser.

NOTE: After five minutes of continuous dispensing, the

dispenser will stop dispensing water to avoid flooding. To

continue dispensing, remove the container and press the

dispensing lever again.

Allow 24 hours for the refrigerator to cool down and chill

water. Dispense enough water every week to maintain a fresh

supply.

Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

Dispense Ice and Water

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

The dispenser will dispense either water or cubed ice.

Express Fill allows you to dispense water into containers that

will not fit within the dispenser area, such as sport bottles.

Select water or cubed ice by touching the word "WATER" or

"CUBES" on the control panel. The light above the control

indicates your selection.

[]

Water

[]

Press a sturdy container against the dispenser lever.

IMPORTANT: You do not need to apply a lot of pressure to the

lever in order to activate the dispenser. Pressing hard will not

make the water or ice dispense faster or in greater quantities.

3. Remove the container to stop dispensing.

Dispenser Light

NOTES:

• The dispenser lights are LEDs which should not need to be

changed.

• When you use the dispenser, the lever will automatically turn

the light on. If you want the light to be on continuously, you

may choose either On or Auto.

Auto On

[] []

Light

I Light Sensor

Auto: The light sensor monitors the light level in the room. The

dispenser light will illuminate at half-power when the light level is

low. To activate the Auto option press the Light button. The Auto

indicator light will illuminate.

On: For continuous light, press the Light button a second time.

The On indicator light will illuminate.

Off: To turn the dispenser light off, press the Light button a third

time.

Dispenser Lock

The dispenser can be locked for easy cleaning or to avoid

unintentional dispensing by small children and pets.

NOTE: The dispenser lock does not shut off power to the product,

to the ice maker, or to the dispenser light. It just deactivates the

dispenser lever.

To Lock and Unlock Dispenser:

Press and hold the Lock/Unlock touch pad for three seconds to

lock the dispenser. The indicator light will illuminate when Lock is

on.

Press and hold the Lock/Unlock touch pad again for

three seconds to unlock dispenser. The indicator light will turn off.

[]

I Lock/Unlock I

hold 3 sec

The water filter is located in the upper right-hand corner of the

refrigerator compartment.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Water Filter Status

The control panel will remind you when it is time to order and

replace your water filter by displaying a message when you

dispense water. "Order Water Filter" means it is almost time to

change the water filter and "Replace Water Filter" means a new

water filter should be installed. It is recommended that you

replace the water filter when you see the "Replace Water Filter"

message OR earlier if the flow of water to your water dispenser or

ice maker decreases noticeably.

Reset Water Filter Status

After replacing the water filter, you must reset the water filter

status to turn off the message.

1. On main menu, press the touch pad next to "Options."

2. In each of the following screens, continue to press the touch

pad next to "More Options" until you reach the "Replace Filter

screen."

3. Press the touch pad next to "YES" to reset the water filter

status. Press the touch pad next to "NO" ifyou do not wish to

reset the water filter status.

Replacing the Water Filter

To purchase a replacement water filter, Part Number UKF8001AXX

contact your dealer or call 1-877-232-6771 USA or

1-800-807-6777 Canada.

IMPORTANT: Air trapped inthe water system may cause water

and filter to eject. Always dispense water for at least 2 minutes

before removing the filter or blue bypass cap.

1. Turn filter counterclockwise to remove.

2. Remove sealing label from replacement filter and insert the

filter end into the filter head.

3. Turn the filter clockwise until it stops. Snap the filter cover

closed.

NOTE: The dispenser feature may be used without a water filter

installed. Your water will not be filtered. If this option is chosen,

replace the filter with the blue bypass cap.

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water.

• To keep your stainless steel refrigerator looking like new

and to remove minor scuffs or marks, it is suggested that

you use the manufacturer's approved Stainless Steel

Cleaner and Polish, Part Number 20000008. To order the

cleaner, call 1-877-232-6771 U.S.A. or 1-800-807-6777

Canada.

IMPORTANT: This cleaner is for stainless steel parts only!

Do not allow the Stainless Steel Cleaner and Polish to come

into contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If unintentional contact

does occur, clean plastic part with a sponge and mild

detergent in warm water. Dry thoroughly with a soft cloth.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

+ 28 hidden pages