Loading...
H
T-1 (3 mm) High Performance
TS AlGaAs Red LED Lamps
Technical Data
Features
•High Light Output over a
Wide Range of Currents (500 μA to 50 mA)
•Popular T-1 Package
•Low Forward Voltage
•Low Power Dissipation
•Deep Red Color
•Long Life: Solid State Reliability
•Wide Viewing Angles
•Available on Tape and Reel
Applications
•Outdoor Message Boards
•Automotive Lighting
•Portable Equipment
•Safety Lighting Equipment
•Medical Equipment
•Changeable Message Signs
HLMP-J100 HLMP-J105 HLMP-J150 HLMP-J155
Package Dimensions
3.18 (0.125)
2.67 (0.105)
3.43 (0.135)
2.92 (0.115)
|
|
4.70 (0.185) |
|
6.35 (0.250) |
|||
|
4.19 (0.165) |
||
5.58 (0.220) |
|
||
|
|
||
|
|
|
1.02 (0.040) NOM.
0.45 (0.018)
SQUARE
NOMINAL
25.40 (1.00) MIN.
ANODE CATHODE
2.54 (0.100) |
1.27 (0.050) |
|||
|
|
|
NOM. |
|
NOM. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Description
The T-1 solid state lamps utilize a highly optimized LED material technology, transparent substrate aluminum gallium arsenide (TS AlGaAs). This LED technology has a very high luminous efficiency, capable of producing high light output over a wide range of drive currents (500 μA to 50 mA). The color is deep red at a dominant wavelength of 644 nm. TS AlGaAs is a flip-chip LED technology, die attached to the anode lead and wire bonded to the cathode lead.
Device Selection Guide
|
Viewing |
|
Typical |
Typical |
|
Angle |
Deep Red |
IV (mcd) |
IV (mcd) |
Package Description |
2θ1/2 |
λd = 644 nm |
IF = 20 mA |
IF = 0.5 mA |
T-1 (3 mm), Untinted, |
45° |
HLMP-J105 |
340 |
– |
Non-diffused, Standard Current |
|
|
|
|
|
|
|
|
|
T-1 (3 mm), Untinted, |
45° |
HLMP-J155 |
– |
6 |
Non-diffused, Low Current |
|
|
|
|
|
|
|
|
|
T-1 (3 mm), Tinted, Diffused, |
55° |
HLMP-J100 |
175 |
– |
Standard Current |
|
|
|
|
|
|
|
|
|
T-1, (3 mm), Tinted, Diffused, |
55° |
HLMP-J150 |
– |
3 |
Low Current |
|
|
|
|
|
|
|
|
|
1-124 |
5964-9372E |
Absolute Maximum Ratings
Peak Forward Current[2] ............................................................ |
300 mA |
Average Forward Current (@ IPEAK = 300 mA)[1,2] ...................... |
30 mA |
DC Forward Current[3] ................................................................. |
50 mA |
Power Dissipation ..................................................................... |
100 mW |
Reverse Voltage (IR = 100 μA) ......................................................... |
5 V |
Transient Forward Current (10 μs Pulse)[4] ............................... |
500 mA |
Operating Temperature Range ........................................ |
-55 to +100°C |
Storage Temperature Range ........................................... |
-55 to +100°C |
LED Junction Temperature ........................................................... |
110°C |
Solder Temperature ................................................ |
260°C for 5 seconds |
[1.6 mm (0.063 in.) from body]
Notes:
1.Maximum IAVG at f = 1 kHz, DF = 10%.
2.Refer to Figure 6 to establish pulsed operating conditions.
3.Derate linearly as shown in Figure 5.
4.The transient peak current is the maximum non-recurring peak current the device can withstand without damaging the LED die and wire bonds. It is not recommended that the device be operated at peak currents above the Absolute Maximum Peak Forward Current.
Optical Characteristics at TA = 25°C
|
Luminous |
|
|
Color, |
Viewing |
|
|
|
Intensity |
Total Flux |
Peak |
Dominant |
Angle |
Luminous |
|
|
IV (mcd) |
φv (mlm) |
Wavelength |
Wavelength |
2θ1/2 |
Efficacy |
|
Part |
@ 20 mA[1] |
@ 20 mA[2] |
λPEAK (nm) |
λd[3] (nm) |
(Degrees)[4] |
ηv |
|
Number |
Min. |
Typ. |
Typ. |
Typ. |
Typ. |
Typ. |
(lm/w) |
HLMP-J105 |
56.4 |
340 |
280 |
654 |
644 |
45 |
85 |
HLMP-J100 |
35.2 |
175 |
|
654 |
644 |
55 |
85 |
Optical Characteristics at TA = 25°C
|
Luminous |
|
|
Color, |
Viewing |
|
|
Part |
Intensity |
Total Flux |
Peak |
ZDominant |
Angle |
Luminous |
|
Number |
IV (mcd) |
φv (mlm) |
Wavelength |
Wavelength |
2θ1/2 |
Efficacy |
|
(Low |
@ 0.5 mA[1] |
@ 0.5 mA[2] |
λPEAK (nm) |
λd[3] (nm) |
(Degrees)[4] |
ηv |
|
Current) |
Min. |
Typ. |
Typ. |
Typ. |
Typ. |
Typ. |
(lm/w) |
HLMP-J155 |
2.1 |
6.0 |
37.2 |
654 |
644 |
45 |
85 |
HLMP-J150 |
1.3 |
3.0 |
|
654 |
644 |
55 |
85 |
Notes:
1.The luminous intensity, IV, is measured at the mechanical axis of the lamp package. The actual peak of the spatial radiation pattern may not be aligned with this axis.
2.φV is total luminous flux output as measured with an integrating sphere.
3.The dominant wavelength, λd, is derived from the CIE Chromaticity Diagram and represents the color of the device.
4.θ1/2 is the off-axis angle where the luminous intensity is 1/2 the peak intensity.
1-125
Loading...