Page 1
Detex Corporation, 302 Detex Drive, New Braunfels, Texas 78130-3045
(830)629-2900 / 1-800-729-3839 / Fax (830)620-6711
E-MAIL: detex@detex.com INTERNET: www.detex.com
INSTALLATION INSTRUCTIONS FOR
03R ADVANTEX® TRIM FOR NARROW STILE (60 SERIES) CVR APPLICATIONS
®
03R Trim for 60 Series
Concealed Vertical Rod Exit Device
60 / F60 / 61 / F61 / 62 / F62 / 63 / F63 Series
Drawing no. 105106
TOOLS AND SUPPLIES
Safety Glasses
(Always put on safety glasses prior
to beginning installation of unit)
Pencil
Center Punch
Hammer
Power Drill
1-1/4" Hole Saw
Drill Bit & Tap Set
Screw Driver (Phillips Drive)
Tape Measure
104871 December 12, 2011
Standard Builder's Hardware Rim
Cylinder sold separately*
p/n: ECL-445-X
p/n: 105210-X
Trim housing
p/n: 105104-X
Must use BP12
backplate
(supplied with exit device)
Hex standoff
p/n: 105105
Tailpiece for 2-1/4"
thick door provided
p/n: 105239-1
Owner's Copy
Tailpiece assembly
for 1-3/4" to 2" thick doors
p/n: 105238-1
Screws & lockwashers
provided with cylinder*
Mounting screws
3 lengths provided (qty 2 each)
p/n: 105622-124 (1-1/2" long for 1-3/4" door)
p/n: 105622-128 (1-3/4" long for 2" door)
p/n: 105622-132 (2" long for 2-1/4" door)
104871 Page 1
Page 2
1. PREPARE THE DOOR - DEVICE SIDE
If not already done, prep the door per the
instructions provided with the exit device.
DEVICE (INSIDE)
FACE
OF DOOR
2. TRANSFER DEVICE CENTERLINES TO TRIM SIDE OF DOOR
device vertical
2a
(backset)
C
L
2b
2c
2d
2e
device horizontal
Transfer vertical (backset)
Position square as shown
to allow for door bevel
C
L
3. PREPARE THE DOOR - TRIM SIDE
Next, prep the hole and slotted opening
shown at right for the trim per the
template (p/n 105285) provided with this trim.
(Template also available on Detex website
See template T2314)
C
L
Measure vertical (backset)
Position square as shown
to allow for door bevel
C
L
104871 Page 2
Page 3
4. PREPARING THE CYLINDER:
Cut rim cylinder tailpiece as
shown below.
5. ASSEMBLE THE TRIM:
Assemble the cylinder (with key removed), trim housing
& tailpiece assembly.
The unit comes assembled with the tailpiece used on
1-3/4 to 2" thick doors. For 2-1/4" thick doors, replace
with the longer tailpiece provided (p/n 105239-1).
1-3/4"
±1/16"
Will always be 90° to
cylinder tailpiece
Cut break-away
cylinder screws as
needed for proper length
6. GO BACK AND FOLLOW EXIT DEVICE INSTRUCTION STEPS up to, but not including
ASSEMBLE DEVICE TO DOOR. Trim must be installed BEFORE device is assembled to door.
7. INSTALL TRIM ON DOOR
With the required BP12 backplate secured, use the appropriate length screws in the TOP HOLE in
each pair of backplate holes above and below the cam (as shown) to install trim.
To access screw holes, peel off
Align tailpiece to cam when
installing
the label attached to top of cam.
Turning the key to rotate the
cam may be necessary to allow
access to both screw holes.
When finished, cam MUST be
in position shown. Tailpiece
MUST NOT protrude past
surface of cam.
8. CONTINUE ON WITH DEVICE INSTRUCTIONS.
104871 Page 3
Cam
installation shown
LHR
TOP HOLE
TOP HOLE
Must use BP12
backplate supplied
with device
p/n: 104148-2
Loading...