|
|
|
R |
|
PXA-H900 |
|
|
||
Multimedia ManagerTM |
|
|
||
|
|
|
|
|
Guide for Installation and Connections |
|
English |
||
|
|
|
|
|
Hinweise über die Installation und Anschlüsse |
|
Deutsch |
||
|
|
|
|
|
Guide d’installation et de connexions |
|
Français |
||
|
|
|
|
|
Guía de instalación y conexiones |
|
Español |
||
|
|
|
|
|
Guida all’installazione ed ai collegamenti |
|
Italiano |
||
|
|
|
|
|
Vägledning för montering och anslutningar |
|
Svenska |
||
|
|
|
|
|
PRECAUTIONS
GUIDE FOR INSTALLATION AND CONNECTIONS
•Please read this GUIDE FOR INSTALLATION AND CONNECTIONS and the OWNER’S MANUAL thoroughly to familiarize yourself with each control and function. We at ALPINE hope that your new PXA-H900 will give you many years of listening enjoyment.
In case of problems when installing your unit, please contact your authorized ALPINE dealer.
Points to Observe for Safe Usage
•Read this manual carefully before starting operation and use this system safely. We cannot be responsible for problems resulting from failure to observe the instructions in this manual.
•This manual uses various pictorial displays to show how to use this product safely and to avoid harm to yourself and others and damage to your property.
Here is what these pictorial displays mean. Understanding them is important for reading this manual.
•Meaning of displays
Warning |
This symbol means important instructions. Failure to heed them can |
|
result in serious injury or death. |
||
|
|
|
Caution |
This symbol means important instructions. Failure to heed them can |
|
result in injury or property damage. |
||
|
||
|
|
Warning
DO NOT DISASSEMBLE OR ALTER. Doing so may result in an accident, fire or electric shock.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may result in fire or electric shock.
MAKE THE CORRECT CONNECTIONS. Failure to make the proper connections may result in fire or product damage.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND. (Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to electrical shorts.
DO NOT SPLICE INTO ELECTRICAL CABLES. Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES. When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.
2-EN
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.
DO NOT INSTALL THE MONITOR NEAR THE PASSENGER SEAT AIR BAG. If the unit is not installed correctly the air bag may not function correctly and when triggered the air bag may cause the monitor to spring upwards causing an accident and injuries.
DO NOT BLOCK VENTS OR RADIATOR PANELS. Doing so may cause heat to build up inside and may result in fire.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN. Swallowing them may result in serious injury. If swallowed, consult a physician immediately.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR SHIFT LEVER. Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.
Caution
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST. Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.
3-EN
Precautions
•Be sure to disconnect the cable from the (–) battery post before installing your PXA-H900. This will reduce any chance of damage to the unit in case of a short-circuit.
•Be sure to connect the color coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage to the vehicle’s electrical system.
•When making connections to the vehicle’s electrical system, be aware of the factory installed components (e.g. on-board computer). Do not tap into these leads to provide power for this unit. When connecting the PXA-H900 to the fuse box, make sure the fuse for the intended circuit of the PXA-H900 has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. When in doubt, consult your ALPINE dealer.
•The PXA-H900 uses female RCA-type jacks for connection to other units (e.g. amplifier) having RCA connectors. You may need an adaptor to connect other units. If so, please contact your authorized ALPINE dealer for assistance.
Wiring Connections
Improper wiring connections could cause serious damage to your audio system. Be sure you:
1.DO NOT connect (–) wires from left and right speakers together.
2.DO NOT ground any speaker wires.
3.DO NOT run wires where they may be pinched or cut.
4.DO NOT leave bare speaker terminals exposed. They may contact the vehicle chassis and cause a short.
Fuse
When replacing the fuse(s), the replacement fuse must be of the same amperage as shown on the fuse holder. If the fuse(s) blows more than once, carefully check all electrical connections for shorted circuitry. Also have your vehicle’s voltage regulator checked. Do not attempt to repair the unit yourself; return it to your Alpine dealer or nearest Alpine Service Station for servicing.
Temperature
In order to ensure proper performance, be sure the temperature in your vehicle is above 14 F (–10 C) and below 140 F (60 C) before turning your unit on. Good air circulation is essential to prevent internal heat build-up in the unit.
4-EN
Contents |
|
|
PRECAUTIONS |
2 |
|
Accessories |
6 |
|
Installation |
7 |
|
Connections |
12 |
|
Examples of system expansion |
14 |
|
Installing with wires only (no terminals) |
18 |
|
|
|
|
IMPORTANT
Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number plate is located on the bottom of the unit.
SERIAL NUMBER:
INSTALLATION DATE:
INSTALLATION TECHNICIAN:
PLACE OF PURCHASE:
To prevent external noise from entering the audio system.
•Locate the unit and route the leads at least 10cm away from the car harness.
•Keep the battery power leads as far away from other leads as possible.
•Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
•If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise suppressors. Contact them for further information.
•Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
5-EN
Accessories
Ai-NET cable |
|
|
|
Display cable |
|
|
Stand |
Microphone |
|||||||
(6m) |
|
|
|
(6m) |
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Connection |
Spacer |
Bracket |
Spare fuse |
Cable |
|
|
(15A) |
Velcro tape for |
Velcro tape for |
Battery (AAA) |
Flanged self- |
mounting |
mounting stand |
|
tapping screw |
remote control |
|
||
|
|
(M4 x 14) |
|
unit holder |
|
|
|
|
|
|
|
|
|
x 4 |
x 4 |
Pan head screw |
Flat head screw |
Remote control |
Remote control |
(M3 x 5) |
(M5 x 8) |
|
unit holder |
Terminal board cover
Hexagonal wrench (M2.6)
Hexagon screw (M4 x 10)
x 2
Screw for mounting remote control unit holder (M2.9 x 20)
x 4 |
|
x 4 |
|
x 2 |
Side bracket |
Inner case |
Flush mount |
Pan head screw |
Self-tapping |
|
|
|
(M2.6 x 6) |
screw |
|
|
|
|
(M2.6 x 8) |
One on each side |
|
x 2 |
x 2 |
x 4 |
Face plate |
|
|
|
|
6-EN
Loading...