Yamaha PSR-730E, PSR-730 User Manual

SPECIAL MESSAGE SECTION
This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recom­mended by Yamaha.
This product should be used only with the components supplied or; a cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is used, please observe all safety markings and instructions that accom­pany the accessory product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained in this manual is believed to be correct at the time of printing. However, Yamaha reserves the right to change or modify any of the specifications without notice or obligation to update existing units.
This product, either alone or in combination with an amplifier and head­phones or speaker/s, may be capable of producing sound levels that could cause permanent hearing loss. DO NOT operate for long periods of time at a high volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an audiologist. IMPORTANT: The louder the sound, the shorter the time period before damage occurs.
NOTICE:
Service charges incurred due to a lack of knowledge relating to how a function or effect works (when the unit is operating as designed) are not covered by the manufacturer’s warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your dealer before requesting service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both user safe and envi­ronmentally friendly. We sincerely believe that our products and the production methods used to produce them, meet these goals. In keep­ing with both the letter and the spirit of the law, we want you to be aware of the following:
Battery Notice:
This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of
battery is approximately five years. When replacement becomes nec­essary, contact a qualified service representative to perform the re­placement.
This product may also use “household” type batteries. Some of these may be rechargeable. Make sure that the battery being charged is a rechargeable type and that the charger is intended for the battery being charged.
When installing batteries, do not mix batteries with new, or with batter­ies of a different type. Batteries MUST be installed correctly. Mis­matches or incorrect installation may result in overheating and battery case rupture.
Warning:
Do not attempt to disassemble, or incinerate any battery. Keep all batteries away from children. Dispose of used batteries promptly and as regulated by the laws in your area. Note: Check with any retailer of household type batteries in your area for battery disposal information.
Disposal Notice:
Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and federal regulations that relate to the disposal of prod­ucts that contain lead, batteries, plastics, etc. If your dealer is unable to assist you, please contact Yamaha directly.
NAME PLATE LOCA TION:
The name plate is located on the bottom of the product. The model number, serial number, power requirements, etc., are located on this plate. You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent record of your purchase.
Model
Serial No.
Purchase Date
92-BP
PLEASE KEEP THIS MANUAL
FCC INFORMATION (U.S.A.)
IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly ap­proved by Yamaha may void your authority, granted by the FCC, to use the product.
IMPORTANT:
When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow in­structions could void your FCC authorization to use this product in the USA.
NOTE:
This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compli­ance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment gener­ates/uses radio frequencies and, if not installed and used according to
• This applies only to products distributed by Yamaha Corporation of America.
the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
• Relocate either this product or the device that is being affected by the interference.
• Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
• In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep these precautions in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
• Do not open the instrument or attempt to disassemble the internal parts or modify them in any way. The instrument contains no user-serviceable parts. If it should appear to be malfunctioning, discontinue use immedi­ately and have it inspected by qualified Yamaha service personnel.
• Do not expose the instrument to rain, use it near water or in damp or wet conditions, or place containers on it containing liquids which might spill into any openings.
• If the AC adaptor cord or plug becomes frayed or damaged, or if there is a sudden loss of sound during use of the instrument, or if any unusual smells or smoke should appear to be caused by it, immediately turn off
the power switch, disconnect the adaptor plug from the outlet, and have the instrument inspected by qualified Yamaha service personnel.
• Use the specified adaptor (PA-6 or an equivalent recommended by Yamaha) only. Using the wrong adaptor can result in damage to the instrument or overheating.
• Before cleaning the instrument, always remove the electric plug from the outlet. Never insert or remove an electric plug with wet hands.
• Check the electric plug periodically and remove any dirt or dust which may have accumulated on it.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other property. These precautions include, but are not limited to, the following:
• Do not place the AC adaptor cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it.
• When removing the electric plug from the instrument or an outlet, al­ways hold the plug itself and not the cord.
• Do not connect the instrument to an electrical outlet using a multiple­connector. Doing so can result in lower sound quality, or possibly cause overheating in the outlet.
• Unplug the AC power adaptor when not using the instrument, or during electrical storms.
• Always make sure all batteries are inserted in conformity with the +/– polarity markings. Failure to do so might result in overheating, fire, or battery fluid leakage.
• Always replace all batteries at the same time. Do not use new batteries together with old ones. Also, do not mix battery types, such as alkaline batteries with manganese batteries, or batteries from different makers, or different types of batteries from the same maker, since this can cause overheating, fire, or battery fluid leakage.
• Do not dispose of batteries in fire.
• Do not attempt to recharge batteries that are not intended to be charged.
• If the instrument is not to be in use for a long time, remove the batteries from it, in order to prevent possible fluid leakage from the battery.
• Keep batteries away from children.
• Before connecting the instrument to other electronic components, turn off the power for all components. Before turning the power on or off for all components, set all volume levels to minimum.
• Do not expose the instrument to excessive dust or vibrations, or ex­treme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or dam­age to the internal components.
• Do not use the instrument near other electrical products such as televi­sions, radios, or speakers, since this might cause interference which can affect proper operation of the other products.
• Do not place the instrument in an unstable position where it might acci­dentally fall over.
• Before moving the instrument, remove all connected adaptor and other cables.
• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths. Also, do not place vinyl or plastic objects on the instrument, since this might discolor the panel or keyboard.
• Do not rest your weight on, or place heavy objects on the instrument, and do not use excessive force on the buttons, switches or connectors.
• Use only the stand specified for the instrument. When attaching the stand, use the provided screws only. Failure to do so could cause dam­age to the internal components or result in the instrument falling over.
• Do not operate the instrument for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician.
SAVING USER DATA
• Always save data to a floppy disk frequently, in order to help prevent the loss of important data due to a malfunction or user operating error.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.
Always turn the power off when the instrument is not in use.
Make sure to discard used batteries according to local regulations.
(4)
1
Congratulations!
Piano
3
4
FREEZE
You are the proud owner of a fine electronic keyboard. The Yamaha PSR-730/630 Por taTone combines the most advanced tone generation technology with state-of-the-art digital electronics and features to give y ou stunning sound quality with maximum musical enjo yment. A large g raphic display and easy-to-use interf ace also greatly enhance the operability of this advanced instrument.
In order to make the most of your P ortaT one’s f eatures and extensive perf ormance potential, we urge you to read the manual thoroughly while trying out the various f eatures described. Keep the manual in a safe place for later reference.
The LCD displays as illustrated in this owner’ s manual are for instructional purposes only , and may appear some what different from those on your instrument. The displa ys from the PSR-730 are used for the instructions and descriptions in this manual.
Important Features
PSR-730
T ouch-sensitive 61-key ke yboard for a wide
range of dynamic musical expression (page 115).
individualize your arrangement of any style of music (page 35).
The Groove & Dynamics function lets you
A variety of voices, 215 panel voices (200 panel voices for PSR-630), 12 drum kits and 480 XG voices, with the maximum polyphony of 64 voices (32 voices for PSR-630).
V oice set feature automaticaly selects the appropriate voice parameter settings f or the panel voices (page 116).
Advanced auto-accompaniment technol­ogy gives y ou 100 fully-orchestrated accompani­ment “styles” to back up what you play on the keyboard (page 22).
Virtual Arranger feature lets you add chord progressions to any of the auto-accompaniment styles for more musical, refined accompaniment (page 29).
Large multi-function LCD display panel
makes it easy to select and edit parameters.
The functional layout of the track buttons
below the panel display makes oper ation easy.
Registration Memory saves your favorite panel settings for instant recall when needed (page 57).
Minus-one and Repeat functions are ideal for learning new songs and polishing your key­board technique (page 79).
Digital effects (reverb, chorus, DSP and harmony) add depth and ambiance to your sound (page 42).
One Touch Setting feature automatically selects appropriate voice, effect, and other set­tings for the selected accompaniment style — all you hav e to do is select a style and play (page 40).
2
PSR-730
The Multi Effect function lets you combine
two digital effects (page 48).
PSR-730
15 16
With the Digital Equalizer you can fine tune the sound of y our performance on five differ­ent frequency bands (page 51).
User Song recording feature makes it easy to record and playback f our melody tracks with an accompaniment track (page 83).
A total of sixteen tracks can be recorded with the Multi recording function, including key­board, harmony and accompaniment (page 88).
Create original accompaniment styles with the User Style feature (you can also establish your o wn rules for changing pitch based on chord changes (page 98).
Multi Pads record and pla y short rhythmic and melodic sequences that can be used to add impact and variety to your performances (page
106).
The floppy disk drive plays XG disks and lets you easily manage User Song, User Style, User Pad and Registration data (page 64).
A range of MIDI functions for expanded musical enjoyment (XG f ormat compatible), and a TO HOST terminal for easy connection to a per­sonal computer (page 121)
MIDI templates for easy MIDI settings (page 129).
GM System Level 1
“GM System Level 1” is an addition to the MIDI standard which ensures that any GM-compatible music data can be accurately played by any GM-compatible tone generator, regardless of manufacturer. The GM mark is affixed to all software and hardw are products that support the “GM System Level 1”.
PSR-730/630 supports GM System Level 1.
Packing List
Please check that these items are packed with your PSR-730/630.
• PSR-730/630
XG
XG is a new MIDI format created by Yamaha which significantly improves and expands upon the “GM Sys­tem Level 1” standard by providing a greater variety of high-quality voices plus considerably enhanced effect operation while being fully compatible with GM.
PSR-730/630 supports the XG format.
• Music Stand (page 7)
• Sample Disk
• Owner’s manual
3
Contents
Panel Controls 6
The Music Stand ........................................................7
Basic Display Operation 8
The Display Icons............................................................8
The Menus .....................................................................10
Shortcuts .................................................................11
Setting Up 12
Power Supply.................................................................12
Using An Optional AC Power Adaptor.........................12
Using Batteries ............................................................12
Connections ..................................................................13
PHONES Jack.............................................................13
SUSTAIN Pedal Jack...................................................13
FOOT VOLUME Jack ..................................................13
AUX OUT R and L/L+R Jacks .....................................13
MIDI IN/OUT and TO HOST Connectors ....................13
The Demonstration 14
Digital Effects 42
Reverb ...........................................................................43
Selecting a Reverb Type..............................................43
Reverb Return Level....................................................43
Chorus ...........................................................................44
Selecting a Chorus Type .............................................44
Chorus Return Level ...................................................44
DSP ...........................................................................45
Select the DSP Type ...................................................45
DSP Return Level........................................................46
Harmony.........................................................................47
Selecting a Harmony Type ..........................................47
Adjusting the Harmony Volume ...................................48
Multi Effect (PSR-730) ...................................................48
How Multi Effect Works ...............................................48
Applying Multi Effect (PSR-730) ..................................49
Setting Parts for Effect 1/2 ..........................................49
Select the Effect Type for Effect 1/2.............................50
Adjust the Dry/Wet Settings for Effect 1/2 ...................50
The Digital Equalizer (PSR-730) ...................................51
Using the Digital Equalizer (PSR-730) .........................51
Selecting a Digital EQ Type. ........................................52
Setting the Gain (User Setting) ...................................53
Playing the PSR-730/630 16
A Word About the “R1”, “R2”, and “L” Voices .............16
Selecting & Playing R1 Voices .....................................17
Keyboard Percussion ................................................ 19
The Dual Voice Mode.....................................................19
The Split Voice Mode.....................................................20
Changing the SPLIT VOICE Split Point .......................21
Auto Accompaniment 22
What is Auto Accompaniment? ...................................22
Using Auto Accompaniment ........................................22
Changing Tempo ...................................................... 26
The Beat Indicator....................................................26
Accompaniment Sections..........................................27
Accompaniment Track Muting ..................................28
The Synchro Stop Function ....................................... 28
Using Virtual Arranger ..................................................29
Accompaniment V olume Control .................................29
Changing the Accompaniment Split Point.................. 30
Interaction Between the AUTO ACCOMPANIMENT
and SPLIT VOICE Split Points.............................. 31
The Auto Accompaniment Fingering Modes..............31
The Stop Accompaniment Function ...........................35
Groove and Dynamics (PSR-730) ................................35
Applying Groove & Dynamics......................................36
Arranging the Groove & Dynamics Effect
(User Settings).......................................................36
One Touch Setting .........................................................40
The Pitch Bend Wheel 54
Setting the Pitch Bend Range ......................................54
The Modulation Wheel (PSR-730) 55
Changing the Modulation Wheel Function .................55
Transpose 56
Setting T ransposition....................................................56
Registration Memory 57
Registering the Panel Settings ....................................57
Naming the Registration Banks ...................................58
Recall the Registered Panel Settings ..........................60
The Accompanient Freeze Function ...........................60
The Multi Pads 61
Selecting a MULTI PAD Set...........................................61
Playing the MULTI PADs ...............................................62
Turning the CHORD MATCH Function On/Off ............63
Disk Operations 64
Floppy Disk Handling Precautions.............................64
User Song Data...........................................................65
User Style/User Pad/Registration Memory Data .........65
Data that Can be Saved or Loaded with the
PSR-730/630 ........................................................65
4
Using Commercially Available Music Collections
(Sold Separately)...................................................66
The Sample Disk ...........................................................66
Format ...........................................................................67
Save ...........................................................................68
Load ...........................................................................70
Disk Copy.......................................................................72
Song Copy .....................................................................73
Delete File ......................................................................75
Song Playback 76
Song Playback Procedure............................................76
Song Volume Control...................................................78
Play from a Specified Measure ...................................78
Minus-one Practice .......................................................79
Repeat Play....................................................................80
Song Repeat ..................................................................81
Next Song ......................................................................82
Song Recording 83
Quick Recording Procedure.........................................84
Rehearsal Mode .......................................................86
Multi Recording Procedure ..........................................88
About the Recording with the Digital Effects Applied . 90
Punch In/Punch Out ....................................................92
Quantize ......................................................................93
Naming User Songs ....................................................94
Clearing Song Data .....................................................94
Song Edit.....................................................................96
Overall Functions 114
Touch Sensitivity........................................................115
Pitch Bend Range .....................................................115
Modulation Wheel......................................................115
Master Tuning............................................................ 115
Scale Tuning.............................................................. 115
Song Transpose.........................................................116
Metronome ................................................................116
Split Voice Split Point.................................................116
Accompaniment Split Point .......................................116
Fingering Mode .........................................................116
Voice Set ...................................................................116
Pedal .........................................................................117
MIDI Functions 119
What’s MIDI?................................................................119
MIDI Terminal/TO HOST Terminal ......................... 121
What You Can Do with MIDI........................................121
Connecting to a Personal Computer
(TO HOST Terminal/HOST SELECT Switch)....................122
Connect using the PSR-730/630 MIDI terminals ......122
Connect using the TO HOST terminal.......................124
The PSR-730/630 MIDI Functions ..............................125
Transmit Channel & Transmit Track ...........................125
Receive Channel & Receive Mode...........................126
Local Control .............................................................127
Clock .........................................................................128
Initial Data Send ........................................................128
MIDI Template ........................................................... 129
Style Recording 98
Style Recording Procedure ..........................................98
Rehearsal Mode .....................................................101
Drum Cancel .............................................................103
Quantize ....................................................................103
Naming Styles ...........................................................104
Clearing User Style Data...........................................105
Multi Pad Recording 106
Multi Pad Recording Procedure.................................106
Naming Pads.............................................................109
Clearing User Pad Data ............................................109
Revoicing 110
Revoicing the R1, R2, and L Voices ........................... 110
Revoicing a Style.........................................................112
Appendix 130
PSR-730/630 Display MENU/SUB MENU Structure ..130
Voice List .....................................................................133
Maximum Polyphony .................................................133
Drum Kit List................................................................140
Style List ......................................................................142
About Digital Effects (Reverb/Chorus/DSP) .............143
When DSP type Is Selected as a System Effect ....... 143
When DSP type Is Selected as a Insertion Effect .....144
Harmony Type List ......................................................147
Refining User Styles with Style File Format .............148
Style File (Auto Accompaniment) Format..................148
About the Source Chord Type ................................... 150
Troubleshooting .......................................................... 151
Data Backup & Initialization .......................................152
Data Backup..............................................................152
Data Initialization .......................................................152
MIDI Data Format.........................................................153
MIDI Implementation Chart ........................................168
Specifications..............................................................171
Index.............................................................................172
5
Panel Controls
PSR-730
PITCH BEND MODULATION
q w
PHONES
PSR-630
1
2
AUTO ACCOMPANIMENT
STYLE
001 ~ 011 012 ~ 019 020 ~ 022 023 ~ 030 031 ~ 034 035 ~ 041
STAND BY ON
MASTER VOLUME
MAX
MIN
DEMO
3
SYNC STOP START
4 5 6
8BEAT 16BEAT 6/8 BALLAD DANCE DISCO ROCK
RESET
TEMPO
TRANSPOSE
ACMP / SONG
VOLUME
ACCOMPANIMENT
ON / OFF
INTRO
042 ~ 047 048 ~ 051 052 ~ 060 061 ~ 065 066 ~ 070 071 ~ 081
DIGITAL MULTI EFFECT
DIGITAL EQ MULTI EFFECT
REVERB HARMONY
CHORUS
VARIATION
RHYTHM&BLUES ROCK&ROLL COUNTRY&WESTERN TRADITIONAL JAZZ CONTEMPORARY JAZZ LATIN
DSP
MAIN / AUTO FILL
0
8
RECORD
082 ~ 083
CARIBBEAN
084 ~ 087
BALLROOM LATIN
088 ~ 091
BALLROOM STANDARD
092 ~ 095
MARCH
096 ~ 100
WALTZ
SUB MENU
MENU
MENU
9
BA
BA
GROOVE&DYNAMICS
START / STOP
ENDING
7
MAX
MIN
PANEL VOICE
001 ~ 019 020 ~ 031
032 ~ 054 055 ~ 061 062 ~ 081
DISK
116
001
MULTI PAD
STYLE
DISK
000
TRANSPOSE
SONG
REGIST MEMORY
MULTI
DIGITAL EQ
EFFECT
MIDI
12345678910111213141516
DIGITAL EFFECT
OVERALL
RHYTHM
2
ACCOMPANIMENT TRACK
REVOICE
BANK
MEMORY
082 ~ 096
PIANO
097 ~ 108
CHROMATIC
109 ~ 128
PERCUSSION
129 ~ 137
ORGAN
138 ~ 153
ACCORDION GUITAR
154 ~ 168
AB
ONE TOUCH
100
TEMPO
REPEAT
213
ACMP/SONG
REGISTRATION MULTI PAD
VOLUME
VARIATION
REVERB HARMONYCHORUS DSP SYNC STOP
!
2
REGISTRATION MEMORY
BASS SOLO STRINGS ENSEMBLE SOLO BRASS BRASS ENSEMBLE REED
nd Pianop1 Gra8Beat Po
001
SETTING
MEASURE
FREEZE
4
MEMORY
FINGERING mM
SONG TRACKLR2 R1
@
BEAT
1234
dim
MELODY3MELODY2MELODY1MELODY
4
169 ~ 176 177 ~ 194 195 ~ 215 216 ~ 227
001
VOICE
119
6
513
GROOVE & DYNAMICS
7
augsus
4
001001001001001001001001001001001001001001001001
ACMP VOICEVOICEVOICERHYTHM1BASS CHORD 1CHORD 2PAD PHRASE1PHRASE
L
R1R2
DUALSPLIT
FREEZE
SYNTH LEAD SYNTH PAD DRUM KITS
161 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
VOICE
STYLE
SONG
ONE TOUCH SETTING
228 ~ 266 267 ~ 286
287 ~ 322 323 ~ 351 352 ~ 393
#
VOICE
STYLE
SONG
XG VOICE
PIPE
)
F1
C1
e
CLICK
36 37 39 41 4238 40 43 45 46 50 51 5244 47 48 49 53 55 5754 5856 6259 60 61 69 7063 716564 66 67 7268 73 7574 76 77 78 79 808381 82
E1
D1
T S R 1 1 2 32 3 L H L HRS
G1 A1
B1 C2 D2 E2
F2
G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 G5 A5 B5
M
M
C
L
H
1
R 1
C
R
HLHLHLHL
2
2
r
394 ~ 405 406 ~ 439 440 ~ 471 472 ~ 484 485 ~ 492
STRINGS ENSEMBLE BRASS REED PIPE
PIANO CHROMATIC PERCUSSION ORGAN GUITAR BASS 493 ~ 528 SYNTH LEAD
&
KEYBOARD
SPLIT VOICE DUAL VOICE
*
$
STOP
12341234
529 ~ 557
SYNTH PAD
558 ~ 613
SYNTH EFFECTS ETHNIC
614 ~ 634
PERCUSSIVE
635 ~ 657
SOUND EFFECTS
658 ~ 665 666 ~ 707 SFX
PSR-730
%
123
456
789
^
/ NO
0
+
/ YES
MULTI PAD
(
HLSLHLMO
84 85 86 8887 89 90 91 93 9492 95
PITCH BEND
q
PHONES
e
PSR-730/630
1
2
AUTO ACCOMPANIMENT
STYLE
001 ~ 011 012 ~ 019 020 ~ 022 023 ~ 030 031 ~ 034 035 ~ 041
STAND BY ON
MASTER
VOLUME
MAX
MIN
DEMO
3
SYNC STOP START
8BEAT 16BEAT 6/8 BALLAD DANCE DISCO ROCK
4 5 6
RESET
TEMPO
TRANSPOSE
ACMP / SONG
VOLUME
ACCOMPANIMENT
ON / OFF
INTRO
042 ~ 047 048 ~ 051 052 ~ 060 061 ~ 065 066 ~ 070 071 ~ 081
7
RHYTHM&BLUES ROCK&ROLL COUNTRY&WESTERN TRADITIONAL JAZZ CONTEMPORARY JAZZ LATIN
0
DIGITAL EFFECT
REVERB HARMONY
CHORUS
DSP
8
RECORD
VARIATION
MAIN / AUTO FILL
082 ~ 083
CARIBBEAN
084 ~ 087
BALLROOM LATIN
088 ~ 091
BALLROOM STANDARD
092 ~ 095
MARCH
096 ~ 100
WALTZ
SUB MENU
MENU
9
START / STOP
ENDING
BA
BA
REGISTRATION MEMORY
PANEL VOICE
001 ~ 018
PIANO
019 ~ 030
CHROMATIC PERCUSSION ORGAN
031 ~ 051 052 ~ 057
ACCORDION
058 ~ 073
GUITAR
MENU
DISK
001
MULTI PAD
STYLE
SONG
REGIST MEMORY
MIDI
12345678910111213141516
DIGITAL EFFECT
OVERALL
REVOICE
116
100
TEMPO
DISK
000
ACMP/SONG
TRANSPOSE
VOLUME
REVERB HARMONYCHORUS DSP SYNC STOP
RHYTHM
2
ACCOMPANIMENT TRACK
MEMORY
AB
REPEAT
213
REGISTRATION MULTI PAD
VARIATION
!
074 ~ 088 089 ~ 100 101 ~ 118 119 ~ 126 127 ~ 140 141 ~ 155
ONE TOUCH
2
SETTING
4
FREEZE
MEMORY
@
BASS SOLO STRINGS ENSEMBLE SOLO BRASS BRASS ENSEMBLE REED
001
MEASURE
156 ~ 163 164 ~ 181 182 ~ 200 201 ~ 212
nd Pianop1 Gra8Beat Po
001
BEAT
1234
VOICE
119
6
dim
513
7
augsus
4
FINGERING mM
ACMP VOICEVOICEVOICERHYTHM1BASS CHORD 1CHORD 2PAD PHRASE1PHRASE
MELODY3MELODY2MELODY1MELODY
4
L
SONG TRACKLR2 R1
DUALSPLIT
001001001001001001001001001001001001001001001001
R1R2
FREEZE
PIPE SYNTH LEAD SYNTH PAD DRUM KITS
161 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
VOICE
STYLE
SONG
ONE TOUCH SETTING
XG VOICE
213 ~ 251
PIANO
252 ~ 271
CHROMATIC PERCUSSION ORGAN
272 ~ 307 308 ~ 336
GUITAR
337 ~ 378
BASS 478 ~ 513 SYNTH LEAD
VOICE
STYLE
SONG
STOP
#
379 ~ 390 391 ~ 424 425 ~ 456 457 ~ 469 470 ~ 477
&
KEYBOARD
SPLIT VOICE DUAL VOICE
*
12341234
)
C1
CLICK
T S R 1 1 2 32 3 L H L HRS
36 37 39 41 4238 40 43 45 46 50 51 5244 47 48 49 53 55 5754 5856 6259 60 61 69 7063 716564 66 67 7268 73 7574 76 77 78 79 808381 82
F1
E1
D1
G1 A1
B1 C2 D2 E2
F2
G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 G5 A5 B5
M
M
C
L
H
1
R 1
C
R
HLHLHLHL
2
2
r
514 ~ 542
%
^
SYNTH PAD
543 ~ 598
SYNTH EFFECTS ETHNIC
599 ~ 619
PERCUSSIVE
620 ~ 642
SOUND EFFECTS
643 ~ 650 651 ~ 692 SFX
PSR-630
123
456
789
/ NO
0
+
/ YES
STRINGS ENSEMBLE BRASS REED PIPE
MULTI PAD
(
HLSLHLMO
84 85 86 8887 89 90 91 93 9492 95
MAC PC1 PC2 MIDI
MIDI
IN
OUT SUSTAINTO HOSTFOOT VOL
AUX OUT
RL / L+R
DC IN 10-12V
tyuiopQ
6
Top Panel Controls
q STAND BY/ON Switch ......................... page 14
w MASTER VOLUME Control..................page 14
e DEMO Button.......................................page 14
Panel Controls
GROOVE & DYNAMICS Button
!4
(PSR-730) ......................................... page 36
!5 NUMBER Buttons ................................ page 10
!6 + and – Buttons.................................... page 10
!7 Data Dial ..............................................page 10
r TEMPO Buttons ...................................page 26
t TRANSPOSE Buttons..........................page 56
y ACCOMPANIMENT/SONG VOLUME
Buttons..........................................pages 29,78
u AUTO ACCOMPANIMENT SECTION
• AUTO ACCOMPANIMENT
ON/OFF Button .................................page 23
• SYNC STOP Button..........................page 28
• SYNC START Button ........................page 24
C6
96
• INTRO Button ................................... page 24
• MAIN/AUTO FILL A & B Buttons.......page 24
• ENDING Button.................................page 25
!8 KEYBOARD SECTION
• DUAL VOICE Button ......................... page 19
• SPLIT VOICE Button......................... page 20
!9 MULTI PAD SECTION
• STOP Button.....................................page 62
• 1, 2, 3, 4 Buttons............................... page 62
@0 Keyboard..............................................page 18
@1 PITCH BEND Wheel ............................page 54
@2 MODULATION Wheel (PSR-730) ........ page 55
@3 PHONES Jack......................................page 13
@4 Disk Drive.............................................page 64
i RECORD Button .................... pagse 84,99,106
Rear Panel Controls
o START/STOP Button................pages 15,23,25
!0
DIGITAL MULTI EFFECT SECTION (PSR-730) DIGITAL EFFECT SECTION (PSR-630)
• DIGITAL EQ Button (PSR-730).........page 51
• REVERB Button ................................page 43
• CHORUS Button ...............................page 44
• DSP Button .......................................page 45
• VARIATION Button ............................ page 46
• MULTI EFFECT Button (PSR-730) ...page 49
• HARMONY Button ............................page 47
@5 FOOT V OL Jack...................................page 13
@6 TO HOST Connector..........................page 121
@7 HOST SELECT Switch ......................page 122
@8 MIDI IN and OUT Connectors............page 121
@9 SUSTAIN Jack......................................page 13
#0 AUX OUT R, L/L+R Jacks ....................page 13
#1 DC IN 10-12V Jack ..............................page 12
!1 DISPLAY & RELATED CONTROLS
• DISPLAY............................................. page 8
• MENU Buttons .................................. page 10
• SUB MENU Buttons..........................page 10
• VOICE Button....................................page 10
C6
96
• STYLE Button ...................................page 10
• SONG Button ....................................page 10
• REVOICE Button.............................page 110
• TRACK Buttons......... pages 19,20,28,86,111
The Music Stand
!2 REGISTRATION MEMORY SECTION
• BANK [+], [ –] Buttons (PSR-730) .....page 58
• MEMORY Button...............................page 58
• 1, 2, 3, 4 Buttons............................... page 58
• FREEZE Button ................................ page 60
!3 ONE TOUCH SETTING Button ............page 41
The PSR-730/630 is supplied with a music stand that can be attached to the instrument by inserting it into the slot at the rear of the control panel.
7
Basic Display Operation
001
The PSR-730/630 LCD panel is a large multi-function type that simultaneously displays and provides access to a number of important parameters. Basic operation of the displa y as well as the MENU and SUB MENU buttons, and the meaning of the icons which appear in the display, are summarized briefly below.
The Display Icons
001
DISK
Style/Song Number
The style number or song number is dis­played here when in the Song/Style Mode.
Disk
Appears when a floppy disk song is selected (page 76).
Voice Number (R1 Voice)
The currently selected R1 voice num­ber (page 17) appears here.
XG
Appears when one of the PSR-730/ 630’s XG voices is selected (page
16).
XG
Appears when XG voices are used in a floppy disk song.
nd Pianop1 Gra8Beat Po
AB
REPEAT
REGISTRATION MULTI PAD
VARIATION
DISK
MULTI
EFFECT
116
100
TEMPO
000
TRANSPOSE
REVERB HARMONYCHORUS DSP SYNC STOP
ACMP/SONG
VOLUME
001
STYLE
SONG
DIGITAL EQ
12345678910111213141516
ONE TOUCH
SETTING
213
4
MEMORY
FREEZE
001
MEASURE
1234
FINGERING mM
dim
BEAT
6
7
119 513
augsus
4
001
VOICE
GROOVE & DYNAMICS
00100100100100100100100100100 100100100100100100 1
BASS CHORD 1CHORD 2PAD PHRASE1PHRASE
RHYTHM
1
2
ACCOMPANIMENT TRACK
12345678
RHYTHM
1
BASS CHORD 1CHORD 2PAD PHRASE1PHRASE
RHYTHM
2
910111213
213213252201471
MELODY
2
1
4
3
MELODY
MELODY
MELODY
8
ACMP
MELODY
2
1
SONG TRACK
2
4
3
L
L
R1R2
DUALSPLIT
R2 R1
ACMP VOICEVOICEVOICERHYTHM
MELODY
MELODY
MELODY
ACCOMP ANIMENT TRA CKS
347324407324322340219219
These icons display the on/off status and volume/velocity settings for each of the 8 accompaniment tracks. They are also used to specify tracks when using the REV OICE function (page 110). When
2
doing Multi recording/playback of songs, the on/off status and volume settings are shown for tracks 1-8 (page 89).
MELODY TRACKS 1 … 4, ACCOMPANIMENT TRACK
In Song Quick Record mode, the recording track is indicated(page
86). When doing Multi recording/playback of songs, the on/off status and volume settings are shown for tracks 9-13 (page 89).
Basic Display Operation
116
0
100
AB
ONE TOUCH
SETTING
213
FREEZE
4
1
1234
TEMPO
Shows the current tempo of accompani­ment/song playback (page 26).
TRANSPOSE
The current transpose value (page 56).
ACMP/SONG VOLUME
In Song/Style Mode (page 11), the ac­companiment or song volume is displa yed (pagse 29,78).
REPEAT
Indicates the “A” and “B” repeat points when programming a repeat section, and whether REPEA T PLA Y is on or off (page
80).
ONE TOUCH SETTING
Appears when the ONE TOUCH SET­TING feature is engaged (page 41).
REGISTRATION 1 … 4 (Registration Memory)
Indicates the currently selected REGIS­TRATION MEMORY or ONE TOUCH SETTING number (page 57).
FREEZE
Appears when the REGISTRATION MEMORY “FREEZE” function is on (page
60).
MEASURE
Indicates the current measure number during song recording and playback (page
78).
BEA T
Flashes at the current tempo and indi­cates the current beat during accompa­niment and song playback. (page 26)
MULTI PAD 1 … 4
Indicates the currently playing MUL TI P AD numbers (page 62).
VARIATION
mM
DIGITAL EQ (PSR-730)
Appears when the DIGIT AL EQU ALIZER is turned on (page 51).
MULTI EFFECT (PSR-730)
Appears when the MUL TI EFFECT is turned on (page 49).
REVERB
Appears when the PSR-730/630 REVERB effect is turned on (page 43).
CHORUS
Appears when the CHORUS eff ect is turned on (page 44).
DSP
Appears when the DSP effect is turned on (page 45).
DSP VARIATION
Appears when the DSP VARIA TION effect is turned on (page 46).
HARMONY
Appears when the HARMONY effect is turned on (page 47).
SYNC STOP
Appears when AUTO ACCOMPANIMENT SYNC STOP function is engaged (page
28).
FINGERING
Shows the currently selected fingering mode (page 32).
CHORD
Displays the current chord name during
7
AUTO ACCOMPANIMENT playback or SONG recording/playback (page 25).
GROOVE & DYNAMICS
Appears when the GROO VE & DYNAMICS function is engaged (page 36).
(PSR-730)
14 15 16
L
DUALSPLIT
Keyboard Settings (VOICE R1/VOICE R2/VOICE L)
These icons indicate the on/off status and volume settings for the L, R2, and
001048064
VOICEVOICEVOICE
R1R2
R1 voices when the DUAL VOICE and/or SPLIT VOICE functions are used (pages 19,20). They are also used to specify trac ks when using the REVOICE function (page 110). During Multi recording/playback of songs, the y indicate the on/off status, volume/velocity and voice settings for tracks 14-16 (page 86).
9
Basic Display Operation
The Menus
MENU
Main Menu Selection (VOICE/STYLE/SONG Buttons)
Y ou can select one of the three main VOICE/STYLE/SONG menus by pressing the appropriate button to the right of the display. The menu icon selected.
Selecting Other Menus (MENU [], [▼] Buttons)
You can select one of the seven “DISK” “MULTI PAD” “REGIST MEMORY” “MIDI” “DIGITAL EFFECT” “OVERALL” “GROO VE & DYNAMICS” menus on the left of the display by pressing the [], [] MENU buttons at the lower left. The menu icon you have selected.
will move to indicate the menu you have
will move to indicate the menu
SUB MENU
MENU
MENU
MULTI PAD
REGIST MEMORY
DIGITAL EFFECT
OVERALL
GROOVE&DYNAMICS
AB
DISK
MIDI
001
STYLE
DIGITAL EQ
116
100
TEMPO
DISK
000
ACMP/SONG
TRANSPOSE
SONG
MULTI
EFFECT
12345678910111213141516
RHYTHM
2
ACCOMPANIMENT TRA CK
VOLUME
REVERB HARMONYCHORUS DSP SYNC STOP
ONE TOUCH
SETTING
REPEAT
213
FREEZE
4
MEMORY
REGISTRATION MULTI PAD
VARIATION
MELODY
2
001
MEASURE
FINGERING mM
MELODY
2
1
SONG TRACK
MELODY
nd Pianop1 Gra8Beat Po
3
BEAT
1234
119
6
dim
513
7
augsus
MELODY
ACMP VOICEVOICEVOICERHYTHM1BASS CHORD 1CHORD 2PAD PHRASE1PHRASE
4
4
L
L
001
VOICE
GROOVE & DYNAMICS
001001001001001001001001001001001001001001001001
R1R2
DUALSPLIT
R2 R1
SUB MENU Selection (SUB MENU [], [] Buttons)
You can select one of the sub menus within the selected menu by pressing the [], [] SUB MENU buttons at the upper left of the display. At the top of the display, the MENU/SUB MENU you selected will displayed on the left and the current setting or v alue f or that item on the right.
123
Number Buttons [1]-[0], [+] (YES), [–] (NO) Buttons
456
The number buttons [1] – [0], [+],[–], are used to change settings (values). Pressing the [+] button increases the dis-
789
played value by 1. Pressing the [–] button decreases it by 1. Pressing and holding either button causes a continuous in-
/ NO
0
+
/ YES
crease or decrease. Pressing the [+] (YES) or [–] (NO) buttons also switches betw een on and off settings. For items that have initial default v alues , pressing the [+] and [–] buttons together at the same time will return the setting to the initial value.
Dial
Like the number buttons [1]-[0], [+],[–], the dial is used to change settings and values. Rotating it to the right (clockwise) increases the value, while rotating it to the left (counter­clockwise) decreases it. The dial can also be used to toggle on/off settings.
• When the value displayed is a number like a style number, press­ing and holding either the [+] or [–] button will cause the number to continue to the lowest value after the highest is reached or vice-
m
versa (...99
100m1m2..., ...2m1m100m99...). If the number dis­played is a value like a transpose value, it will stop changing when the maximum or minimum value is reached.
VOICE
STYLE
SONG
VOICE
STYLE
SONG
10
Basic Display Operation
There are two modes in the PSR-730/630: Style Mode and Song Mode , and normally one of them is selected. Pressing the STYLE button selects Style Mode , lighting the STYLE icon, while pressing the Song button selects Song Mode and lights the SONG icon, displaying the current mode.
STYLE
Style Mode * Pressing the START/STOP button will start accompaniment playback.
Currently selected style name and style number
Accompaniment volume
001
STYLE SONG
DIGITAL EQ
12345678910111213141516
1
116
DISK
000
TRANSPOSE
MULTI
EFFECT
BASS CHORD 1CHORD 2PAD PHRASE1PHRASE
RHYTHM
2
ACCOMP ANIMENT TRA CK
Information for accompaniment tracks 1-8
SONG
Song Mode * Pressing the START/STOP button will start song playback.
Currently selected song name and song number
Song volume
001
STYLE
SONG
DIGITAL EQ
12345678910111213141516
1
116
DISK
000
TRANSPOSE
MULTI
EFFECT
BASS CHORD 1CHORD 2PAD PHRASE1PHRASE
RHYTHM
2
ACCOMP ANIMENT TRA CK
Information for song tracks 1-16
AB
ONE TOUCH
100
TEMPO
REVERB HARMONYCHORUS DSP SYNC STOP
100
TEMPO
REVERB HARMONYCHORUS DSP SYNC STOP
ACMP/SONG
VOLUME
ACMP/SONG
VOLUME
REPEAT
VARIATION
AB
REPEAT
VARIATION
SETTING
213
FREEZE
4
MEMORY
REGISTRATION MULTI PAD
MELODY
2
ONE TOUCH
SETTING
213
FREEZE
4
MEMORY
REGISTRATION MULTI PAD
MELODY
2
001
MEASURE
FINGERING mM
MELODY
2
1
SONG TRACK
001
MEASURE
FINGERING mM
MELODY
2
1
SONG TRACK
MELODY
MELODY
nd Pianop1 Gra8Beat Po
3
nd Pianorid GraLondon B
3
BEAT
1234
119
6
dim
513
7
augsus
ACMP VOICEVOICEVOICERHYTHM
MELODY
4
BEAT
1234
119
6
dim
513
7
augsus
ACMP VOICEVOICEVOICERHYTHM
MELODY
4
4
GROOVE & DYNAMICS
L
L
GROOVE & DYNAMICS
4
L
L
001
VOICE
001109084888888888888888362324407339337355219219
R1R2
DUALSPLIT
R2 R1
001
VOICE
213213213213213252219471442468434259391337213213
R1R2
DUALSPLIT
R2 R1
• When in Song Mode, AUTO ACCOM­PANIMENT ON/OFF , SYNC START, SYNC STOP and other buttons con­nected with accompaniment will not function.
Shortcuts
To make operation as easy and as efficient as possible, the PSR-730/630 features a number of “shortcuts” which allow you to jump directly to certain functions without having to use the MENU and SUB MENU buttons. All of these shortcuts work in the same way: press and hold a panel button for a few seconds to go to the related function. For example, if you press and hold the [REVERB] button for a few seconds , y ou will go directly to the REVERB type selection function. The shorcuts will also be described where appropriate throughout this manual.
11
Setting Up
This section contains information about setting up your PSR-730/630 and preparing to play. Be sure to go through this section carefully before using your PSR-730/630.
Power Supply
• Never interrupt the power supply (e.g. remove the
Although the PSR-730/630 will run either from an optional AC adaptor or batteries, Y amaha recommends use of the more environmentally safe A C adaptor. Follow the instructions below according to the power source you intend to use .
Using An Optional AC Power Adaptor
batteries or unplug the AC adaptor) during any PSR-730/630 record op­eration! Doing so can re­sult in a loss of data.
z Plug an optional Yamaha PA-6 Power Adaptor into a wall AC outlet. x Then plug the DC output cable from the PA-6 into the DC IN 10-12V jack on
the rear panel of the PSR-730/630. The internal batteries are automatically disconnected when an AC Power Adaptor is used.
DC IN 10-12V
PA-6
When turning the power OFF, simply reverse the procedure.
Using Batteries
For battery operation the PSR-730/630 requires six 1.5V SUM-1, “D” size, R­20 or equivalent batteries. When the batteries need to be replaced “Lo Battery!!” may appear on top of the display, the volume ma y be reduced, the sound may be distorted, and other problems may occur. When this happens, turn the power off and replace the batteries.
Replace the batteries as follows:
z Open the battery compartment cover located on the instrument’ s bottom panel. x Insert the six new batteries, being careful to follow the polarity markings on
the inside of the compartment.
c Replace the compartment cover, making sure that it locks firmly in place.
• Use ONLY a Yamaha PA-6 AC Power Adaptor (or other adaptor specifically recom­mended by Yamaha) to power your instrument from the AC mains. The use of other adap­tors may result in irreparable damage to both the adaptor and the PSR-730/630.
• Unplug the AC Power Adap­tor when not using the PSR­730/630, or during electrical storms.
• When the batteries run down, replace them with a complete set of six new batteries. NEVER mix old and new batteries.
• Do not use different kinds of batteries (e.g. alkaline and manganese) at the same time.
• If the instrument is not to be in use for a long time, remove the batteries from it, in order to prevent pos­sible fluid leakage from the battery.
• Plugging or unplugging the AC power adaptor while the batteries are in­stalled will reset the PSR­730/630 to the defaults.
Important Notes on Battery Use
• Since the PSR-730 and PSR-630 consume a considerable amount of power , Yamaha recommends the use of an A C power adaptor rather than batteries. The batteries should be consid­ered an auxiliary power source for data backup.
• The floppy disk drive, in pa rticular, uses a large amount of power, so it is impor tant to always use an AC power ada ptor when performing disk-intensive operations such as song re­cording/playback or data load/save. If you attempt to use battery power for these operations and the batteries do fail, you will lose not only the data you’re recording or sa ving, b ut also
12
other data in internal memory including user styles, user pads, registration memory, etc.
• Taking the above precautions into consideration, always use an AC power adaptor when using the PSR-630/730 for an impor­tant performance or when creating important data.
• When using batteries and the “Lo Battery!!” war ning initially appears on the display, the v olume will drop a little but you will be able to use the instrument for a while longer. When the “Lo Battery!!” warning begins to appear every few seconds, re­place the batteries as soon as possible.
Connections
PHONES Jack
SUSTAIN Pedal Jack
SUSTAIN
FOOT VOLUME Jack
FOOT VOL
A standard pair of stereo headphones can be plugged in here for private pr actice or late-night playing. The internal stereo speaker system is automatically shut off when a pair of head­phones is plugged into the PHONES jack.
Do not listen with the headphones at high vol­ume for long periods of time. Doing so may cause hearing loss.
The sustain function causes the sound from a depressed key to continue, even after the key is released. Plug an optional Yamaha FC4 or FC5 footswitch into the sustain jack and use it to switch sustain on and off. The footswitch con­nected to this jack can also be set to replicate the functions of some panel buttons, doing things like starting and stopping accompaniment (page
117).
Connecting an optional Y amaha FC7 foot con­troller lets you use your foot to change the volume as you play the PSR-730/630 (expres­sion function). The foot controller connected to this jack can also be set to replicate the functions of the main volume controls, such as accompani­ment or song volume (page 117).
Setting Up
• Be sure that you do not press the footswitch while turning the power on. If you do, the ON/OFF sta­tus of the footswitch will be reversed.
• When the sustain or sostenuto pedal func­tions are being used (page 117), some voices may sound con­tinuously or have a long decay after the notes have been released while the pedal is held.
AUX OUT R and L/L+R Jacks
• • • • • • • • • • • • • • • • • •
AUX OUT
L/L+R
R
The rear-panel AUX OUT R and L/L+R jacks
deliver the output of the PSR-730/630 for con­nection to a keyboard amplifier, stereo sound system, a mixing console, or tape recorder. If you will be connecting the PSR-730/630 to a monaural sound system, use only the L/L+R jack. When a plug is inserted into the L/L+R jack
Stereo
System
only, the left- and right-channel signals ar e com­bined and delivered via the L/L+R jack so you don’t lose any of the PSR-730/630 sound. (Use phone plugs).
MIDI IN/OUT and TO HOST Connectors
See page 121.
• Connecting PSR­730/630 to external equipment only after turning off power for all devices. To pre­vent damage to the speakers, set the volume of the exter­nal devices at the minimum setting be­fore connecting them. Failure to ob­serve these cautions may result in elec­tric shock or equip­ment damage.
13
The Demonstration
Once you’ve set up your PSR-730/630, try listening to the pre-progr ammed demonstration songs. A total of 15 demo songs are provided.
Switch ON
1
Turn the power ON by pressing the [STAND BY/ON] switch.
STAND BY ON
• Even when the switch is in the “STAND BY” position, electricity is still flowing to the instrument at the mini­mum level. When you are not using the PSR-730/630 for a long time, make sure you unplug the AC power adoptor from the wall AC outlet, and/or remove the batteries from the instru­ment.
Set an Initial Volume Level
2
Turn the [MASTER V OLUME] control up (c lockwise) about a quarter-turn
from its minimum position. You can re-adjust the [MASTER VOLUME] control for the most comfortable overall volume level after playbac k begins.
MASTER VOLUME
MAX
Press the [DEMO] Button
3
MIN
Press the [DEMO] button to start demo playback. The PSR-730/630 SONG
menu will automatically be selected and the number and name of the first demo song will appear on the top line of the display. The demo will begin playing automatically. The demo songs will play in sequence, and the sequence will repeat until stopped.
• If you play the PSR-730/630 with the volume at its maxi­mum level when the batteries are used, the life of the bat­teries will be shorter.
• You can either have all the demo songs played continu­ously, or have only one song play (page 77).
14
DEMO
tTrumpet
Skip to the Beginning Of a Different Demo Song
4
While the demonstration is playing you can select any of the demo songs by
using the [–] and [+] buttons. Playback will skip to the beginning of the selected song.
123
456
The Demonstration
Stop When Done
5
dR&B
789
/ NO
0
+
/ YES
Press the [DEMO] button or the [ST ART/ST OP] button to stop demo playback.
DEMO
START / STOP
• Stopping demo song playback, then start­ing it again by press­ing the [START/ STOP] button will cause demo song playback to automati­cally stop at the end of that song.
• If the [DEMO] button is pressed in Style Mode (page 11), the instrument will auto­matically switch to Song Mode (page 11).
15
Playing the PSR-730/630
The PSR-730/630 actually includes two voice sets: the “panel” voices and percussion kits, and the XG voices. The panel voices include 215 “pitched” voices (200 “pitched” voices for PSR-630) and 12 drum kits, while the XG voice set includes 480 voices . When an XG voice is selected, an XG icon of the display.
Panel Voices Voice numbers 1-215 Voice numbers 1-200 Drum Kits Voice numbers 216-227 Voice numbers 201-212 XG Voices Voice numbers 228-707 Voice numbers 213-692
Choose a voice you like, and try it out!
• Refer to the panel voice list or XG voice list when selecting voices (page 133).
• See page 3 for information about XG.
is displayed under the v oice number at the top
PSR-730 PSR-630
A Word About the “R1”, “R2”, and “L” Voices
The PSR-730/630 allows up to three voices to be selected at the same time: “R1” (Right-hand 1), “R2”, (Right-hand 2) and “L” (Left-hand). The “R1” voice is the basic voice of the PSR-730/630 and it’s used when you’re playing a single voice over the entire range of the keyboard as with an acoustic piano. Y ou can also have two voices play together at the same time (R1 voice and R2 voice) or play dif ferent voices with the right and left hands (R1 voice and L voice) (pages 19, 20). The numbers of the currently selected R1, R2, and L voices are all shown at the lower right of on the display panel. Normally, the R1 voice n umber is also shown at the upper right of the display panel.
001109084
L
VOICEVOICEVOICE
R1R2
DUALSPLIT
Playing with a Single Voice
Playing with Two Voices
The R1 (Right-hand 1), the R2 (Right-hand 2) and the L (Left hand) voices are shown.
L
R1 Voice
(Dual Voice Mode m page 19).
L
R1 Voice + R2 Voice
VOICEVOICEVOICE
R1R2
DUALSPLIT
VOICEVOICEVOICE
R1R2
DUALSPLIT
16
Playing Separate Voices with the Right and Left Hands (Split V oice Mode m page 20)
VOICEVOICEVOICE
R1R2
DUALSPLIT
VOICEVOICEVOICE
R1R2
DUALSPLIT
L Voice
L Voice
(Split Voice Mode + Dual Voice Mode)
R1 Voice
R1 Voice + R2 Voice
L
L
Playing the PSR-730/630
Selecting & Playing R1 Voices
Select the VOICE Menu
1
Press the [V OICE] button so that the triangular indicator appears in the display next
to “VOICE” to the right of the display . The number and name of the cur rently selected “R1” voice appears on the top right of the display panel when the VOICE menu is selected.
nd Pianop1 Gra
001
VOICE
Select a Panel Voice
2
The PSR-730/630 voices can be selected by using the [–] and [+] buttons, the
number buttons, the data dial, or the [VOICE] button.
The [–] and [+] Buttons
When the VOICE menu is selected these b uttons step up or down through the PSR­730/630’s voices. Press either button briefly to step to the next voice in the corresponding direction, or hold the button to scroll rapidly through the voices in the corresponding direction.
ghtPianop1 Bri
002
VOICE
789
/ NO
VOICE
0
+
/ YES
The Number Buttons
The number buttons can be used to directly enter the number of the desired voice, thereby immediately selecting that voice without having to step through a number of other voices. T o select v oice number 109, for example, press the [1], [0], and [9] number buttons in sequence.
123
ingsp1 Str
109
* The above illustration shows the display of the PSR-730.
456
789
/ NO 0+ / YES
17
Playing the PSR-730/630
One- or two-digit voice numbers can be entered without leading zeros. To select voice number “23”, for example , simply press the [2] button and then the [3] button. The bars below the voice number on the display will f lash for a few seconds, and then disappear when the selected voice number has been recognized by the PSR­730/630.
123
ophonep1 Xyl
023
* The above illustration shows the display of
the PSR-730.
456
789
/ NO
0
+
/ YES
One- or two-digit voice numbers can also be enter ed with leading zeroes: e.g. “23” can be entered as “023” by pressing the [0], [2], and [3] buttons. In this case the specified voice number will be immediately recognized by the PSR-730/630.
The Data Dial
Simply rotate the dial clockwise to increment the voice number, or counter­clockwise to decrement the voice number.
The [VOICE] Button
Pressing the [VOICE] button increments the voice number. Press briefly to increment by one, or hold for continuous incrementing.
VOICE
Play & Adjust Volume
3
You can now play the selected voice on the PSR-730/630 keyboard. Use the [MASTER VOLUME] control to adjust the overall volume level.
If the Voice Set function (page 116) is turned “on”, whenever a panel voice is selected appropriate “R2” and “L” voices (i.e. DUAL VOICE and SPLIT VOICE modes) as well as digital effects, etc., will be automatically selected at the same time.
MASTER VOLUME
MIN
MAX
• When a XG voice is selected the XG icon will appear below the voice number.
• Refer to page 133 for a complete list of the panel and XG voices.
18
Playing the PSR-730/630
Keyboard Percussion
When one of the 12 panel DRUM KIT voices are selected you can pla y different drums and percussion instruments on the keyboard. The drums and percussion instruments played by the various keys are marked by symbols below the keys.
.Kit1p1 Std
* The above illustration shows the display of the PSR-730.
The Drum Kits
PSR-730 PSR-630 Kit Name
216 201 Standard Kit1 217 202 Standard Kit2 218 203 Room Kit 219 204 Rock Kit 220 205 Electronic Kit 221 206 Analog Kit
216
PSR-730 PSR-630 Kit Name
222 207 Dance Kit 223 208 Jazz Kit 224 209 Brush Kit 225 210 Classic Kit 226 211 SFX Kit 1 227 212 SFX Kit 2
VOICE
• The HARMONY effect (page 47) cannot be turned on while a drum kit is selected for the “R1” voice, and will automatically be turned off if a drum kit is selected while HARMONY is on.
• The TRANSPOSE pa­rameter (page 56) has no effect on the drum kit voices.
• See page 140 for a complete listing of the keyboard percussion drum instrument as­signments.
The Dual Voice Mode
When the DU AL V OICE mode is engaged you can play two voices (the R1 and R2
voices) simultaneously across the entire keyboard.
The DUAL VOICE mode is turned on and off by pressing the [DUAL VOICE]
button. When the DU AL VOICE mode is tur ned on both R1 and R2 icons in the display will light. Press the [DUAL V OICE] button a second time to turn the DU AL VOICE mode off: the R2 icon in the display will go out leaving only the R1 icon lit.
001109084
L
VOICEVOICEVOICE
R1R2
DUALSPLIT
In the Syle mode, the R2 TRA CK button below the display (second from the right)
can also be used to turn the R2 voice on or off as required.
001109084
L
L
VOICEVOICEVOICE
R1R2
DUALSPLIT
R2 R1
DUAL VOICE
• The R1/R2 voice set­tings (voice param­eters) can be changed as required by using the REVOICE function, described on page
110.
• The R1 voice cannot be turned off.
• The DUAL VOICE mode can be used at the same time as the SPLIT VOICE mode, described below. In this case the L voice is played on the left-hand section of the key­board while both the R1 and R2 voices are played on the right­hand section of the keyboard. See the “The Split Voice Mode” section, below, for more information.
1614 15 16
19
Playing the PSR-730/630
The Split Voice Mode
The SPLIT V OICE mode lets you play different voices with the left and right hands. The “split point” forms a boundary on the keyboard with the R voice playing on the right side, and the L voice on the left.
The SPLIT VOICE mode is engaged by pressing the [SPLIT VOICE] button. When turned on, the L icon in the display will light in addition to the R1 or R1 and R2 icons. Press the [SPLIT VOICE] button a second time to disengage the SPLIT VOICE mode: the L icon will go out leaving only the R voice.
Split Point
• The L voice settings (voice parameters) can be changed as required by using the REVOICE function, described on page
110.
• The split point can be changed as required as described below.
001109084
L
VOICEVOICEVOICE
R1R2
DUALSPLIT
SPLIT VOICE
In the Syle mode, the L TRACK button belo w the display (third from the right) can
also be used to turn the L voice on or off as required.
001109084
L
L
VOICEVOICEVOICE
R1R2
DUALSPLIT
R2 R1
1614 15 16
20
Playing the PSR-730/630
Changing the SPLIT VOICE Split Point
The SPLIT VOICE split point can be set to any key on the PSR-730/630 keyboard
to match your individual playing requirements.
Select the SPLIT VOICE Split Point Function
1
Use the MENU [] and [] buttons to the left of the display to move the triangular
indicator next to “OVERALL” on the left side of the display.
MENU
DIGITAL EFFECT
GROOVE&DYNAMICS
MIDI
OVERALL
Then use the SUB MENU [] and [] buttons to select the “Split Point” function
from within the OVERALL menu . The MIDI note number (see the bottom of the keyboard) corresponding to the current split point will appear to the right of “Split Point” on the top line of the display.
[ B2 ]nt: 59SplitPoi
Set As Required
2
Simply press the key you want to assign as the split point. The key number of the
key you press will appear to the right of “SplitPoint” on the top line of the display . Y ou can also use the [–] and [+] buttons, number buttons, or data dial to enter the split point key number . The lo west key on the keyboar d (C1) is key number “36”, middle C (C3) is “60”, and the highest key (C5) is 96. The split point can be set at any key number from 0 through 127, allowing the split point to be set outside the range of the PSR-730/ 630 keyboard for MIDI applications.
123
456
789
/ NO
0
+
/ YES
• The split point key be­comes the highest key in the left-hand section of the key­board.
• The default split point (54 for PSR-730 and 59 for PSR-630) can be instantly recalled by pressing the [–] and [+] buttons at the same time.
• For the relationship between the SPLIT VOICE split point and the AUTO ACCOM­PANIMENT split point, see page 31.
• When setting the split point, that is, the sub menu “SplitPoint” is shown on the display, pressing the key on the keyboard doesn’t either produce notes or detect chords in the accompaniment sec­tion, but only desig­nates the split point.
21
Auto Accompaniment
The PSR-730/630 has 100 different accompaniment “styles” from every musical type that can be used to provide fully-orchestrated or rhythm-only accompaniment. Just select one of the many styles available and play along.
What is Auto Accompaniment?
With the Auto Accompaniment feature, all you have to do is play the chords in your song and the accompaniment style that matches your music will automatically play along following the same chord progression. Using Auto Accompaniment, even a solo performer can enjoy playing with an entire band or orchestra backing them up.
When Auto Accompaniment is turned on...
The specified left-hand section of the keyboard becomes the “Auto Accompa­niment” section, and chords played in this section are automatically detected and used as a basis for fully automatic accompaniment with the selected style.
AUTO ACCOMPANIMENT
split point (54)
• The default setting for the Auto Accompani­ment split point is [54] (the Auto Accompani­ment sections ex­tends to the left of key [54]). To change the Auto Accompaniment split point, see page
30.
“auto accompaniment”
section
Using Auto Accompaniment
Select a Style
1
Press the [STYLE] button to select the STYLE menu (the triangular indicator will
appear next to “STYLE” to the right of the display). The number and name of the currently selected style will appear on the top left of the display, and the icon will light, indicating that the PSR-730/630 is in Style Mode.
nd Pianop1 Gra8Beat Po
ACMP/SONG
VOLUME
AB
REPEAT
VARIATION
001
STYLE
SONG
DIGITAL EQ
12345678910111213141516
1
116
100
TEMPO
DISK
000
TRANSPOSE
MULTI
REVERB HARMONYCHORUS DSP SYNC STOP
EFFECT
BASS CHORD 1CHORD 2PAD PHRASE1PHRASE
RHYTHM
2
ACCOMP ANIMENT TRA CK
ONE TOUCH
SETTING
213
4
REGISTRATION MULTI PAD
2
FREEZE
MEMORY
MELODY
001
MEASURE
FINGERING mM
MELODY
2
1
SONG TRACK
MELODY
3
BEAT
1234
6
dim
7
ACMP VOICEVOICEVOICERHYTHM
MELODY
4
119 513
augsus
4
GROOVE & DYNAMICS
L
L
001
VOICE
001109084888888888888888362324407339337355219219
R1R2
DUALSPLIT
R2 R1
VOICE
STYLE
SONG
STYLE
VOICE
STYLE
SONG
22
Auto Accompaniment
Find the style you want by referring to the style list (page 142), then pressing the [1]– [0] number buttons, enter the 1-3 digits of its style number.
Example: Select style number “24” (Dance Pop 2) Press number buttons [2], [4] in sequence.
p2Dance Po
024
Y ou can also change style numbers using the [+], [–] buttons or the Data Dial. Also you can increment the style number by pressing the [STYLE] button. Press briefly to increment by one, or hold for continuous incrementing.
123
456
789
/ NO
0
+
/ YES
• Just like the voice numbers, when se­lecting 1 or 2 digit style numbers, if you add [0] at the begin­ning and enter a 3 digit number, it will be immediately recog­nized. For example, to select style number “95” (Polka) press buttons [0], [9], [5] in sequence.
789
/ NO
Turn AUTO ACCOMPANIMENT On
2
0
+ / YES
STYLE
Press the AUTO ACCOMPANIMENT [ON/OFF] so that its indicator lights.
ACCOMPANIMENT
ON / OFF
Start the Accompaniment
3
There are several ways to start the accompaniment:
• If AUTO ACCOMPA-
NIMENT is off (not lit), only rhythm (drums and percussion) ac­companiment will be produced.
• For information about
the accompaniment tracks, see page 28.
Straight start
Press the [START/STOP] button. The rhythm will begin playing immediately without bass and chord accompaniment. The currently selected MAIN [A] or [B] section will play.
START / STOP
SYNC STOP START
AUTO ACCOMPANIMENT
INTRO
MAIN / AUTO FILL
BA
BA
ENDING
• It is possible to select the MAIN A or B sec­tion prior to a straight start — refer to “7. Select the MAIN A and B Sections as Required,” below.
23
Auto Accompaniment
Start with an introduction followed by the MAIN A section
Press the [INTRO] b utton so that its indicator lights, press the MAIN/A UTO FILL [A] button (not necessary if its indicator is already flashing), then press [ST ART/STOP].
SYNC STOP START
MENT
INTRO
MAIN / AUTO FILL
BA
BA
ENDING
Start with an introduction followed by the MAIN B section
Press the [INTRO] b utton so that its indicator lights, press the MAIN/A UTO FILL [B] button (not necessary if its indicator is already flashing), then press [ST ART/STOP].
SYNC STOP START
MENT
INTRO
MAIN / AUTO FILL
BA
BA
ENDING
Synchronized start
Any of the above start types can be synchronized to the first note or c hord played on the left-hand section of the keyboard (i.e. keys to the left of and including the split-point key — normally 54) by first pressing the [SYNC START] button.
SYNC STOP START
MENT
INTRO
MAIN / AUTO FILL
BA
BA
ENDING
START / STOP
START / STOP
• If you press the [SYNC START] button while the accompaniment is playing, the accompaniment will stop and the synchro start mode will be engaged.
• The [INTRO] button can be used to select the INTRO section even while the ac­companiment is playing.
• The accompaniment split point can be changed via the “Accompaniment Split Point” function in the OVERALL menu — see page 30.
24
Pressing the [SYNC START] button alone causes a straight start to occur when the first note or chord is played. Press the [SYNC START] b utton and then the appropriate [INTRO] and [MAIN/AUTO FILL] buttons for a synchronized introduction start. The BEAT indicator will flash at the current tempo when a synchronized start mode has been selected. The synchro start mode can be disengaged prior to actually starting the accompaniment by pressing the [SYNC START] button a second time.
SYNC STOP START
IMENT
INTRO
MAIN / AUTO FILL
BA
BA
ENDING
• When the AUTO ACCOM­PANIMENT split point and SPLIT VOICE split point are set at different keys, the L voice can be played be­tween the AUTO ACCOM­PANIMENT split point and SPLIT VOICE split point when the AUTO ACCOM­PANIMENT function is on.
• When the AUTO ACCOM­PANIMENT split point and SPLIT VOICE split point are set to the same key, the L voice can be played any­where to the left of the AUTO ACCOMPANIMENT split point and SPLIT VOICE split point while AUTO ACCOMPANIMENT is not playing.
Play the Melody with the Accompaniment
4
As soon as you play any chord that the PSR-730/630 can “recognize” on the left­hand section of the keyboard, the PSR-730/630 will automatically begin to play the chord along with the selected rhythm and an appropriate bass line. The name of the current chord will appear on the display.
1234
MULTI PAD
119
6
dim
FINGERING mM 7augsus
513
GROOVE & DYNAMICS
4
VOICE
The chord will be recognized according to the rules set in the Fingering Mode.
• For the method for entering chords, see page 32 “A uto Accompaniment Fingering Modes. ”
The Auto Accompaniment will continue playing even if the left hand releases the keys. As you press each chord in the song, you can play the melody along with the accompaniment.
Auto Accompaniment
• When the Fingering Mode is set for “Single Finger,” “Fingered 1,” “Fingered 2,” or “Multi-Finger,” playing a chord in the auto accom­paniment section while the rhythm is stopped will cause Bass + Chord to be played (for all styles). However, when the Auto Accompaniment split point and the Split Voice split point are the same key, playing a chord in the ac­companiment section with the rhythm stopped will cause Bass + L voice to be played.
Changing Accompaniment Sections
5
You can vary the song by pressing [INTRO], MAIN/AUTO FILL [A]/[B] or [ENDING] buttons and changing to a different accompaniment section (page 27).
Try pressing the different buttons and see what happens.
INTRO
Stop the Accompaniment
6
MAIN / AUTO FILL
BA
BA
ENDING
Press the [START/STOP] button to stop the accompaniment.
START / STOP
If you want to stop after playing the ending, press the [ENDING] button. The accompaniment will stop after playing the ending .
ENDING
• The ending will begin playing immediately when you press the ENDING button while the accompa­niment is playing the first beat of the measure. The ending will begin playing from the next measure when you press the button while the ac­companiment is playing the second or larger num­bered beat.
• If you press the INTRO button while the ending is playing, the intro section will begin playing after the ending is finished.
• If you press a MAIN/ AUTO FILL (A,B) button while the ending is play­ing, fill-in accompaniment will immediately start play­ing, continuing with the main section.
• If you press the SYNC START while an accom­paniment is playing, the accompaniment will stop and the PSR-730/630 will enter Synchronized Start standby status.
25
Loading...
+ 62 hidden pages