Yaesu HRI-200 User Manual
HRI-200
Reference Manual
for DR-1X/XE
This Reference Manual is for the DR-1X/XE
with MAIN firmware V1.10Q.
YAESU MUSEN CO., LTD.
Activate HRI mode
SETUPPOWER
SETUPPOWER
P
C
-
YHJ
O K ?
REPEATER MODE
Cance
Change the repeater mode to the HRI mode
1. Turn the DR-1X/XE power OFF.
2. While pressing and holding the
[
SETUP] button, press the [POWER] switch.
3. While the “YAESU” logo is being displayed, release the
“HRI+REPEATER MODE” will appear on the display.
[
4. Touch
OK?
]
HRI mode will activate.
Return to REPEATER mode from HRI mode
1. Turn the DR-1X/XE power OFF.
2. While pressing and holding the
[
SETUP] button, press the [POWER] switch.
[
SETUP] button.
HRI+REPEATER MODE
O K ?
P
YHJ
C
Cance
-
3. While the “YAESU” logo is being displayed, release the
“REPEATER MODE” will appear on the display.
[
4. Touch
The operation mode screen will appear on the display.
OK?
]
[
SETUP] button.
1
Connecting Devices
DC 12 V - 15 V (EU)TX Antenna RX Antenna
Connecting HRI-200 to a DR-1X/XE
10 pin plug
Mini-DIN digital cable
(supplied with HRI-200)
LAN cable
(sold separately)
Type A plug
10 pin plug
Type B plug
To the Internet
USB cable (supplied with HRI-200)
AC 100 V - 240 V
(USA, EXP, AUS, CHN)
2
Repeater setting
If an HRI-200 control mode repeater is connected, the following repeater setting screen for exclusive use of
Repeater is displayed.
• When an HRI-200 control mode repeater is detected, the setting information is read from the Repeater and
is displayed on the screen.
• If connecting an HRI-200 control mode repeater, switch on the DR-1X/XE unit while simultaneously pressing
the mechanical [SETUP] button on the front panel. When the “YAESU” logo is displayed on the LCD touch
screen, release the [SETUP] button, the LCD will change to “HRI-REPEATER MODE”. Then press the [OK]
button.
• If operating in Analog FM mode while connected to an HRI-200 control mode repeater, noise squelch can be
adjusted by pressing the [SQL] button (setup screen) and touching the [p] / [q] button.
Voice CH
Voice CH uses WIRES-X to communicate via the Internet.
Operation will be executed by controlling the repeater connected to the HRI-200 Radio 1 terminal.
The following parameters need to be set/display for operation.
Transceiver
Select the Repeater operation mode from the following:
• RX:FM - TX:FM: FM Analog repeater (WIRES Operation=Analog (fixed))
• RX:DIGITAL - TX:DIGITAL: C4FM Digital repeater (WIRES Operation=Digital (fixed))
• RX:AMS - TX:FM: AMS to FM repeater (WIRES Operation=Analog (fixed))
• RX:AMS - TX:DIGITAL: AMS to C4FM repeater (WIRES Operation=Analog (fixed))
• RX:AMS - TX:AMS: AMS to AMS repeater (WIRES Operation=selectable)
Notes:
• When operating in RX:AMS mode, the WIRES-X system only relays the signal that is selected by the
WIRES Operation setting.
• When “HRI-REPEATER MODE” is started in either the “RX:DIGITAL-TX:FM” or “RX:FM-TX:DIGITAL”
state, the WIRES-X Node cannot operate.
3
Loading...