Whirlpool WRF560SMHV, WRF560SEHZ Maintance Manual

REFRIGERATOR

USER INSTRUCTIONS

THANK YOU for purchasing this high-quality product. Register your new refrigerator at www.whirlpool.com. In Canada, register your refrigerator at www.whirlpool.ca.

For future reference, please make a note of your product model and serial numbers. These can be located on the inside wall of the refrigerator compartment.

Model Number __________________________________________________

Serial Number __________________________________________________

Table of Contents / Índice / Table des matières

REFRIGERATOR SAFETY.................................	2
INSTALLATION INSTRUCTIONS .....................	3
Unpack the Refrigerator .................................	3
Location Requirements...................................	3
Remove and Replace Refrigerator
Doors and Drawer Front .................................	4
Electrical Requirements ..................................	8
Water Supply Requirements...........................	8
Connect the Water Supply .............................	8
Handle Installation and Removal..................	10
Door Closing and Door Alignment................	11
FILTERS AND ACCESSORIES .......................	11
Water Filtration System.................................	11
Install Air Filter...............................................	12
Install Produce Preserver..............................	12
Accessories...................................................	13
REFRIGERATOR USE .....................................	13
Opening and Closing Doors .........................	13
Using the Controls ........................................	13
Water Dispenser ...........................................	15
Ice Maker ......................................................	16
REFRIGERATOR FEATURES .........................	16
Refrigerator Shelves......................................	17
Pantry Drawer ...............................................	17
Crisper...........................................................	17
DOOR FEATURES ...........................................	18
Condiment Bins ............................................	18
Fresh Bin .......................................................	18
Half-Height Bin..............................................	18
REFRIGERATOR CARE ..................................	19
Cleaning ........................................................	19
Changing the Light Bulbs .............................	19
TROUBLESHOOTING .....................................	20
Operation ......................................................	20
Noise .............................................................	21
Temperature and Moisture ...........................	22
Ice and Water................................................	23
Doors.............................................................	25
PERFORMANCE DATA SHEET......................	26
WARRANTY......................................................	27

SEGURIDAD DEL REFRIGERADOR..............	28
INSTRUCCIONES DE INSTALACIÓN............	29
Desempaque el refrigerador.........................	29
Requisitos de ubicación ...............................	30
Cómo sacar y volver a colocar las puertas
y el frente del cajón del refrigerador.............	30
Requisitos eléctricos ....................................	34
Requisitos del suministro de agua...............	34
Conexión del suministro de agua.................	34
Instalación y remoción de las manijas .........	36
Cierre y alineamiento de las puertas............	37
FILTROS Y ACCESORIOS..............................	38
Sistema de filtración de agua.......................	38
Instalación del filtro de aire...........................	38
Instalación del preservador
de alimentos frescos ....................................	39
Accesorios ....................................................	40
USO DE SU REFRIGERADOR........................	40
Cómo abrir y cerrar las puertas....................	40
Uso de los controles.....................................	40
Despachador de agua ..................................	42
Fábrica de hielo ............................................	43
CARACTERÍSTICAS DEL
REFRIGERADOR.............................................	44
Estantes del refrigerador ..............................	44
Cajón-despensa ...........................................	44
Cajón para verduras .....................................	45
CARACTERÍSTICAS DE LA PUERTA............	45
Recipientes para condimento ......................	45
Recipiente para productos frescos..............	45
Recipiente de altura media...........................	46
CUIDADO DE SU REFRIGERADOR ..............	46
Limpieza........................................................	46
Cómo cambiar los focos ..............................	46
SOLUCIÓN DE PROBLEMAS ........................	47
Funcionamiento............................................	47
Ruido.............................................................	48
Temperatura y humedad..............................	49
Hielo y agua..................................................	50
Puertas..........................................................	52
HOJA DE DATOS DEL RENDIMIENTO.........	53
GARANTÍA .......................................................	54

SÉCURITÉ DU RÉFRIGÉRATEUR..................	55
INSTRUCTIONS D’INSTALLATION................	56
Déballage du réfrigérateur ............................	56
Exigences d’emplacement............................	57
Retrait et réinstallation des portes
du réfrigérateur et de l’avant du tiroir ...........	57
Spécifications électriques .............................	61
Spécifications de l’alimentation en eau ........	61
Raccordement à l’alimentation en eau .........	61
Installation et démontage des poignées.......	63
Fermeture et alignement de la porte.............	64
FILTRES ET ACCESSOIRES...........................	65
Système de filtration de l’eau .......................	65
Installation du filtre à air ................................	65
Installation du conservateur pour
produits frais .................................................	66
Accessoires...................................................	67
UTILISATION DU RÉFRIGÉRATEUR .............	67
Ouverture et fermeture des portes ...............	67
Utilisation des commandes ..........................	67
Distributeur d’eau..........................................	69
Machine à glaçons ........................................	70
CARACTÉRISTIQUES DU
RÉFRIGÉRATEUR............................................	71
Tablettes du réfrigérateur..............................	71
Garde-manger...............................................	71
Bac à légumes...............................................	72
CARACTÉRISTIQUES DE LA PORTE ............	72
Balconnets à condiments .............................	72
Balconnet fraîcheur .......................................	72
Balconnet mi-hauteur....................................	73
ENTRETIEN DU RÉFRIGÉRATEUR ...............	73
Nettoyage......................................................	73
Remplacement des ampoules d’éclairage ...	74
DÉPANNAGE....................................................	75
Fonctionnement ............................................	75
Bruit ...............................................................	76
Température et humidité...............................	77
Glaçons et eau ..............................................	78
Portes ............................................................	80
FEUILLE DE DONNÉES SUR LA
PERFORMANCE ..............................................	81
GARANTIE ........................................................	82

W10400960C

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:

DANGER

WARNING

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

	■ Plug into a grounded 3 prong outlet.	■ Use nonflammable cleaner.
	■ Do not remove ground prong.	■ Keep flammable materials and vapors, such as gasoline,
	■ Do not use an adapter.	away from refrigerator.
		■ Use two or more people to move and install refrigerator.
	■ Do not use an extension cord.
		■ Disconnect power before installing ice maker (on ice maker
	■ Disconnect power before servicing.
		kit ready models only).
	■ Replace all parts and panels before operating.
		■ Use a sturdy glass when dispensing ice (on some models).
	■ Remove doors from your old refrigerator.
		■ Do not hit the refrigerator glass doors (on some models).

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

Proper Disposal of

Your Old Refrigerator

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous – even if they will sit for “just a few days.” If you are getting rid

of your old refrigerator, please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■Take off the doors.

■Leave the shelves in place so that children may not easily climb inside.

Important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

2

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

■Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

■Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see “Refrigerator Safety.”

■Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as floor damage could occur.

Clean Before Using

After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in “Refrigerator Care.”

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a ¹⁄" (1.25 cm) of space on each side and at the top. Allow for

a 1" (2.54 cm) space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a fixed wall, leave a 2" (5.08 cm) minimum space between the refrigerator and wall to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and

provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near

a heat source, such as an oven or radiator.

¹⁄" (1.25 cm)

2" (5.08 cm)

3

Remove and Replace Refrigerator

WARNING

Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Doors and Drawer Front

Depending on the width of your door opening, it may be necessary to remove the refrigerator doors to move the refrigerator into your home.

Remove Doors and Hinges

IMPORTANT:

■If the refrigerator was previously installed and you are moving it out of the home, before you begin, turn the refrigerator control OFF, and unplug the refrigerator or disconnect power. Remove food and any adjustable door or utility bins from doors.

■Keep the refrigerator doors closed until you are ready to lift them free from the cabinet. Provide additional support for the refrigerator door while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

■All graphics referenced in the following instructions are included later in this section after “Final Steps.”

TOOLS NEEDED: ⁄", ³⁄", and ¹⁄" hex head socket wrenches, Torx®† T25 screwdriver, #2 Phillips screwdriver, and a flat-blade screwdriver.

Remove Doors and Hinges

1.Unplug refrigerator or disconnect power.

2.Remove the base grille. Grasp the grille firmly and pull it toward you.

3.Starting with the right-hand side door, remove the parts for the top hinge as shown in Top Hinge graphic. Lift the refrigerator door from the bottom hinge pin.

4.Remove the hinge pin cover from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic.

†®TORX is a registered trademark of Acument Intellectual Properties, LLC.

5.Remove top hinge cover from the left-hand side refrigerator door. Remove the parts for the top hinge as shown in Top Hinge graphic.

External Dispenser Models Only:

■Disconnect the wiring plug, located under the top left-hand side door hinge, by wedging a flat-blade screwdriver or your fingernail between the two sections. See Wiring Plug graphic.

■Disconnect the water line, located under the top left-hand side door hinge, by pulling back on the locking collar while pulling the water line out of the water line connector. See Water Dispenser Tubing Connection graphic.

6.Lift the left-hand side door from the bottom hinge pin.

NOTE: On some models, remove the hinge pin cover from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic.

Replace Doors and Hinges

1.Replace the parts for the bottom hinge as shown in Bottom Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

2.Assemble the parts for the top hinges as shown in Top Hinge graphic. Do not tighten the screws completely.

External Dispenser Models Only:

■Reconnect the wiring plug on top of the left-hand side refrigerator door.

■Reconnect the water line by pulling back the locking collar ring while firmly pushing the water line into the connector. Check for leaks.

3.Align the door so that the bottom of the refrigerator door aligns evenly with the top of the freezer drawer. Tighten all screws.

4.Replace the top hinge covers.

4

Remove and Replace Freezer Drawer Front

IMPORTANT: Two people may be required to remove and replace the freezer drawer. Graphics are included later in this section.

Remove Drawer Front

1.Open the freezer drawer to full extension.

2.Loosen the four screws attaching the drawer glides to the drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in the drawer front.

3.Lift drawer front upward and off the screws. See Drawer Front Removal graphic.

4.The refrigerator leveling/roller assembly protrudes from each side of the cabinet base. Remove the three screws attaching each assembly, and remove the assemblies. See Refrigerator Leveling/Roller Assembly graphic.

Replace Drawer Front

1.Align the leveling/roller assembly with the holes on each side of the refrigerator cabinet. Using the screws removed, reinstall the assemblies to the cabinet base. Tighten the screws completely.

2.Slide the drawer glides out of the freezer compartment. Insert the screws in the top of the drawer front into the slots in the drawer brackets. See Drawer Front Replacement graphic.

3.Pull the drawer brackets toward you to position the two screws in the bottom of the drawer front into the brackets. Completely tighten the four screws. See Drawer Front Replacement graphic.

4.Replace the base grille.

■Pull open the freezer drawer.

■Align the three clips on the back of the base grille with the three tabs at the base of the refrigerator.

■Push the base grille in toward the refrigerator until it is firmly in place.

Final Steps

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1.Plug into a grounded 3 prong outlet.

2.Return all removable parts to doors and drawer and food to refrigerator and freezer.

A

B

A.Tab

B.Clip

5

Style 1 - Non-Dispenser Models

Door Removal and Replacement

Top Hinges

A

B

C

D

A. Hinge Cover Screw

B. Top Hinge Cover

C. 5/16" Hex-Head Hinge Screws

D. Top Hinge

Bottom Hinges

A

B

C

A. Hinge Pin Cover

B. Bottom Hinge

C. Hinge Screws

Leveling/Roller Assembly

A

A. Assembly Screws

Drawer Front Removal

Drawer Front Replacement

A

A. Loosen 4 Door Bracket Screws

6

Style 2 - External Water Dispenser Models

Water Dispenser

Tubing Connection

A

A. Blue Outer Ring

Wiring Plug

Door Removal and Replacement

Top Hinges

A

B

C

D

A. Hinge Cover Screw

B. Top Hinge Cover

C. ⁄" Hex-Head Hinge Screws

D. Top Hinge

Bottom Hinges

A

B

C

A. Hinge Pin Cover

B. Bottom Hinge

C. Hinge Screws

Leveling/Roller Assembly

A

A. Assembly Screws

7

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only 15or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator and approved accessories be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn OFF Cooling, and then disconnect the refrigerator from the electrical source. When you have finished, reconnect the refrigerator to the electrical source and turn ON Cooling. See “Using the Control(s).”

Water Supply Requirements

A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

■Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

■Allow the storage tank on the reverse osmosis system to refill after heavy usage. The tank capacity could be too low to keep up with the requirements of the refrigerator.

■If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See “Water Filtration System.”

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

■All installations must meet local plumbing code requirements.

■Use copper tubing or Whirlpool supply line, Part Number 8212547RP, and check for leaks.

■Install copper tubing only in areas where the temperatures will remain above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

■	Flat-blade screwdriver	■	¹⁄ " Nut driver
■	⁄ " and ¹⁄ " Open-end or two	■	¹⁄ " Drill bit
	adjustable wrenches	■	Cordless drill

NOTE: Your refrigerator dealer has a kit available with a ¹⁄ "

(6.35 mm) saddle-type shut-off valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or ³⁄ "

(4.76 mm) saddle valve which reduces water flow and clogs more easily.

Connect to Water Line

Style 1

1.Unplug refrigerator or disconnect power.

2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3.Locate a ½" to 1¹⁄ " (1.25 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

■Make sure it is a cold water pipe.

■Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4.Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄ " (6.35 mm)

O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5.Using a cordless drill, drill a ¹⁄ " hole in the cold water pipe you have selected.

	A
G	B
	C
F E	D
A. Cold water pipe	E. Compression sleeve
B. Pipe clamp	F. Shut-off valve
C. Copper tubing	G. Packing nut

D.Compression nut

6.Fasten the shut-off valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the ¹⁄ " (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

8

7.Slip the compression sleeve and compression nut onto the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

8.Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shut-off valve on the water pipe. Coil the copper tubing.

Style 2

1.Unplug refrigerator or disconnect power.

2.Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator.

3.Thread the provided nut onto the water valve as shown.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

A

B

A.Bulb

B.Nut (provided)

4.Turn shut-off valve ON.

5.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Connect to Refrigerator

Style 1

1.Unplug refrigerator or disconnect power.

2.Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten.

3.Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help avoid damage to the tubing when the refrigerator is pushed back against the wall.

4.Turn shut-off valve ON.

5.Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

A

B

C

D

E

A. Tube clamp	D. Compression nut
B. Tube clamp screw	E. Valve inlet

C.Copper tubing

6.On models with ice makers, the ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the ¹⁄ " (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

Style 2

1.Unplug refrigerator or disconnect power.

2.Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator.

3.If the gray water tube supplied with the refrigerator is not long enough, a ¹⁄ " x ¹⁄ " (6.35 mm x 6.35 mm) coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

A	B	C	D	E F G
A. Refrigerator water tubing				E. Ferrule (purchased)
B. Nut (provided)				F. Nut (purchased)
C. Bulb				G.Household water line

D.Coupling (provided)

4.Turn shut-off valve ON.

5.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Complete the Installation

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

NOTES:

■Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

■For models with a water dispenser, flush the water system. See “Water Dispenser.”

9

Handle Installation and Removal

Parts Included: Refrigerator door handles (2),

Freezer drawer handle (1)

Tools Needed: ¹⁄" Hex key wrench

Install Door Handles

NOTE: Handle mounting setscrews are preinstalled inside the handle.

1.Remove the handles from the packaging inside the refrigerator.

2.Open a refrigerator door. On the opposite door, place the handle on the shoulder screws with the setscrews facing the adjacent door.

A

B

A.Shoulder screws

B.Setscrews inside the handle

3.Firmly push the handle toward the door until the handle base is flush against the door.

4.While holding the handle, insert the short end of the hex key into the upper hole and slightly rotate the hex key until it is engaged in the setscrew.

5.Using a clockwise motion tighten the setscrew just until it begins to contact the shoulder screw. Do not fully tighten.

6.Repeat steps 4 and 5 to fasten the lower setscrew.

7.Once both setscrews have been partially tightened as instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an additional quarter-turn. The handle is not properly installed without this extra tightening.

8.Repeat steps 2 through 6 to install the other handle onto the adjacent refrigerator door.

Install Drawer Handle

1.With the freezer drawer closed, place the handle on the shoulder screws with the setscrews facing down toward the floor.

A

B

A.Shoulder screw

B.Setscrews inside the handle

2.Firmly push the handle toward the drawer until the handle base is flush against the drawer.

3.Insert the short end of the hex key into the left-hand hole and slightly rotate the hex key until it is engaged in the setscrew.

4.Using a left-to-right motion tighten the setscrew a quarter-turn at a time. Repeat until the screw feels tight.

5.Repeat steps 3 and 4 to fasten the right-hand setscrew to the shoulder screw.

6.Once both setscrews have been partially tightened as instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an additional quarter-turn. The handle is not properly installed without this extra tightening.

7.Save the hex key and all instructions.

Remove the Handles

1.While holding the handle, insert the short end of the hex key into a setscrew hole and slightly rotate the hex key until it

is engaged in the setscrew.

2.Using a right-to-left motion loosen the setscrew a quarter-turn at a time.

3.Repeat steps 1 and 2 for the other setscrew. Slowly pull the handle away from the door or drawer.

4.If necessary, use a Phillips screwdriver to remove the shoulder screws from the door.

10

Door Closing and Door Alignment

IMPORTANT: To comply with American Disabilities Act (ADA) guidelines, fully retract the rollers into the cabinet to lower the refrigerator.

Door Closing

The base grille covers the leveling screws and roller assemblies located at the bottom of the refrigerator cabinet below the freezer drawer. Before making adjustments, remove the base grille and move the refrigerator to its final location.

1.Remove the base grille. Grasp the grille firmly and pull it toward you.

2.Move the refrigerator to its final location.

NOTE: To allow the refrigerator to roll easier, raise the leveling legs off the floor by turning the leveling screws counterclockwise. The front rollers will be touching the floor.

3.So the doors will close easier, use a ¹⁄" hex driver to turn both leveling screws clockwise. This will raise the front of the refrigerator tilting it slightly downward to the rear. Turn both leveling screws the same amount.

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws. This makes it easier to turn the screws.

¹⁄"

A

B

A.Leveling screw

B.Front roller

4.Open both doors again to make sure they close as easily

as you like and that they stay closed. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns.

NOTE: To keep the refrigerator level, you should turn both leveling screws the same amount.

5.Replace the base grille.

■Pull open the freezer drawer.

■Align the three clips on the back of the base grille with the three tabs at the base of the refrigerator.

■Push the base grille in toward the refrigerator until it is firmly in place.

A

B

A.Tab

B.Clip

Door Alignment

If the space between the refrigerator doors and freezer drawer looks uneven, you can adjust it using the following instructions:

1.Remove the top hinge cover.

2.Loosen the top hinge screws using a ⁄" socket or wrench.

3.Have someone hold the door in place or put a spacer between the doors and drawer.

4.Tighten the top hinge screws once the door is in the desired location.

5.Replace the top hinge cover.

FILTERS AND

ACCESSORIES

Water Filtration System

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Water Filter Status Light

The water filter status light on the control panel will help you know when to order and replace the water filter.

■GOOD - The water filter icon on the control lights up in BLUE.

■ORDER a replacement filter - The water filter icon on the control lights up in YELLOW.

■REPLACE the water filter - The water filter icon on the control lights up in RED and “Replace Filter” will appear on the display.

■EXPIRED - The water filter icon lights up in RED and “Replace Filter” flashes on the display.

NOTE: If water flow to your water dispenser or ice maker decreases noticeably, change the filter sooner. The disposable water filter should be replaced at least every 6 months, depending on your water quality and usage.

■After changing the water filter, reset the status. Press and hold the WATER FILTER button for 3 seconds. When the system is reset, the water filter icon will return to its BLUE color and the words “Replace Filter” will disappear from the display.

Changing the Water Filter

1.Locate the water filter in the top-right corner of the refrigerator compartment.

2.Lift open the filter cover door. The filter will be released and then eject as the door is opened.

3.When the door is completely open, pull the filter straight out.

NOTE: There may be some water in the filter. Some spilling may occur. Use a towel to wipe up any spills.

11

4.Take the new filter out of its packaging and remove the covers from the O-rings. Be sure the O-rings are still in place after the covers are removed.

5.With the arrow pointing up, align the new filter with the filter housing and slide it into place. The filter cover door will automatically begin to close as the new filter is inserted.

6.Close the filter cover door completely in order to snap the filter into place. You may need to press hard.

7.Flush the water system. See “Water Dispenser” or “Water and Ice Dispensers.”

Replacing the Air Filter

The disposable air filter should be replaced every 6 months, or when the status indicator air filter icon turns on and starts flashing when the refrigerator door is opened.

To order a replacement air filter, contact us. See “Accessories.”

1.Remove the used air filter by squeezing in on the side tabs.

2.Install the new air filter and reset the status indicator using the instructions in the previous section.

Install Air Filter

(on some models)

The air filter reduces the buildup of odors. This helps to maintain a cleaner environment inside the refrigerator.

On some models, your refrigerator's accessory packet includes an air filter, which must be installed prior to use. On some models, the air filter is already installed at the factory.

Installing the Air Filter

Install the air filter behind the vented door, located along the rear interior wall of the refrigerator compartment.

1.Remove the air filter from its packaging.

NOTE: An air filter status indicator is included with the air filter. The indicator is not needed for models that display the air filter status on the control panel.

2.Lift open the vented door.

3.Snap the filter into place.

Air Filter Status Indicator

The control panel displays the Air Filter status.

■GOOD - The air filter icon on the control panel lights up in BLUE.

■ORDER a replacement - The air filter icon on the control panel lights up in YELLOW.

■REPLACE air filter - The air filter icon on the control panel lights up in RED and “Replace Filter” will appear.

■EXPIRED - The air filter icon lights up in RED and “Replace Filter” flashes on the control panel.

After replacing the air filter, press and hold the AIR FILTER button for 3 seconds. The filter icons will turn off. See “Using the Control(s).” When the system is reset, the air filter icon will return to its BLUE color and the words “Replace Filter” will disappear from the control panel.

NOTE: At any filter status, pressing and holding the AIR FILTER button for 3 seconds will reset the air filter status to Good and the air filter icon will turn off.

Install Produce Preserver

(on some models)

The accessory packet includes two produce preserver pouches, which should be installed in a crisper drawer prior to use.

NOTE: For best performance, always use two pouches.

The produce preserver absorbs ethylene, to slow the ripening process of many produce items. As a result, certain produce items will stay fresh longer.

Ethylene production and sensitivity varies depending on the type of fruit or vegetable. To preserve freshness, it is best to separate produce with sensitivity to ethylene from fruits that produce moderate to high amounts of ethylene.

					Produces Ethylene
				Very	Low	High	Very
				Low			High
		Sensitivity
		to Ethylene
		High		Broccoli			Apples
				Lettuce			Pears
				Spinach
		Med.		Asparagus		Cantaloupe
				Citrus fruit
		Low		Carrots	Berries
				Grapes

Installing the Produce Preserver

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia, bleach or acids. Do not get in eyes, on skin or clothing. Do not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium permanganate. If swallowed, call a Poison Control Center or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for 15 minutes. If on skin, rinse with water.

12

The produce preserver pouches should be installed in the housing, located on the wall of one of the crisper drawers.

1.Remove the FreshFlow™ Produce Preserver pouches from the packaging.

2.Lift up on the housing to remove it from the mounting tab.

3.Open the housing by pulling up and out on the back of the top of the housing.

4.Place both pouches inside the housing, then snap the housing back together.

5.Place the housing back on the mounting tab.

Installing the Status Indicator

The produce preserver comes with a status indicator, which should be activated and installed at the same time the pouches are installed.

1.Place the indicator face-down on a firm, flat surface.

2.Apply pressure to the bubble on the back of the indicator until the bubble pops, to activate the indicator.

3.Slide open the cap on the top of the produce preserver housing.

4.Place the indicator in the top of the housing, facing outward.

5.Slide the cap closed, and check that the indicator is visible through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator’s bubble has not been popped.

Replacing the Produce Preserver

The disposable pouches should be replaced every 6 months, when the status indicator has completely changed from white to red.

To order replacements, contact us. See “Accessories” for information on ordering.

1.Remove the used pouches from the produce preserver housing.

2.Remove the used status indicator.

3.Install the replacement pouches and status indicator using the instructions in the previous sections.

Accessories

The following accessories are available for your refrigerator. To order, contact us and ask for the part numbers.

In the U.S.A., visit our web page www.whirlpool.com/ accessories or call 1-800-901-2042.

In Canada, visit our web page www.whirlpool.ca or call 1-800-807-6777.

affresh® Stainless Steel Cleaner:

Order Part #W10355016

affresh® Stainless Steel Wipes:

Order Part #W10355049

affresh® Kitchen & Appliance Cleaner:

Order Part #W10355010

Water Filter:

Order Part #W10295370A or FILTER1

Air Filter:

Order Part #W10311524 or AIR1

Produce Preserver:

Order Part #W10346771A or FRESH1

Water Filter, Air Filter and Ethylene Filter Bundle Pack:

Order Part #W103655758BL

REFRIGERATOR USE

Opening and Closing Doors

There are two refrigerator compartment doors. The doors can be opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

■When the left-hand refrigerator door is opened, the hinged seal automatically folds inward so that it is out of the way.

■When both doors are closed, the hinged seal automatically forms a seal between the two doors.

A

A. Hinged seal

Using the Controls

IMPORTANT:

■Wait 24 hours for your refrigerator to cool completely before adding food. If you add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature controls to a colder than recommended setting will not cool the compartments any faster.

■The recommended setting should be correct for normal household refrigerator use. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.

13

■If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.

Control Panel

Depending on your model, your refrigerator has either an internal control panel, located at the top of the refrigerator compartment, or an external control panel, located above the external water dispenser. Follow the instructions specific to your model.

Internal Control Panel

External Control Panel

IMPORTANT (External Control only): The display screen on the dispenser control panel will turn off automatically and enter “sleep” mode when the control buttons and dispenser paddles have not been used for 2 minutes or more. While in “sleep” mode, the first press of a control button will only reactivate the display screen, without changing any settings. After reactivation, changes to

any settings can then be made. If no changes are made within 2 minutes, the display will re-enter “sleep” mode.

■Touch any control button on the dispenser panel to activate the display screen.

Temperature Control

For your convenience, the temperature control is preset at the factory. When you first install your refrigerator, make sure the control is still set to the recommended setting as shown.

Recommended Setting “3 Snowflakes”

Adjusting the Controls

If you need to adjust the temperature in either the refrigerator or freezer compartment, use the settings listed in the following chart as a guide.

■Press the TEMP button to display the desired number of snowflakes from 1 snowflake (least cold) to all 5 snowflakes (coldest).

NOTE: Except when starting the refrigerator, do not adjust the control more than one setting at a time. Wait 24 hours between adjustments for the temperature to stabilize.

CONDITION/REASON:	ADJUSTMENT:
REFRIGERATOR too warm	FRIDGE TEMP
	one more snowflake
FREEZER too warm/too little ice	FREEZER TEMP
	one more snowflake
REFRIGERATOR too cold	FRIDGE TEMP
	one less snowflake
FREEZER too cold	FREEZER TEMP
	one less snowflake

Cooling On/Off

Your refrigerator and freezer will not cool when cooling

is turned off. Follow the directions specific to your model.

Internal Control Panel

■To turn cooling off, press and hold both the FAST COOL and MOISTURE CONTROL buttons at the same time for 3 seconds. When cooling is off, “Cooling Off” will appear on the display screen.

■To turn cooling back on, press and hold both the FAST COOL and MOISTURE CONTROL buttons at the same time for 3 seconds. When cooling is ON, “Cooling Off” will disappear and the previously selected settings will appear on the display screen.

External Control Panel

■To turn cooling off, press and hold both the FREEZER TEMP and FRIDGE TEMP buttons at the same time for 3 seconds. When cooling is OFF, “Cooling Off” will appear on the display screen.

14

■To turn cooling back on. Press and hold both the FREEZER TEMP and FRIDGE TEMP buttons at the same time for

3 seconds. When cooling is ON, “Cooling Off” will disappear and the previously selected settings will appear on the display screen.

Additional Features

Door Open Alarm

■The Door Open icon lights up whenever either door is opened.

■When either door is open for 5 minutes and cooling is on, an alert tone will sound three times, and the Door Open icon will flash seven times. This pattern will repeat every 2 minutes until all the doors are closed properly. The feature then resets and will reactivate when either door is left open again for 5 minutes.

NOTES:

■To mute the audible alarm while keeping the doors open, such as while cleaning the inside of the refrigerator, press any button on the control panel. The alarm sound will be temporarily turned off, but the Door Open icon will still be displayed on the dispenser control panel.

■Both doors must be fully closed to turn off the Door Open icon.

Fast Cool

The Fast Cool feature assists during times of high refrigerator use, full grocery loads or temporarily warm room temperatures.

■Press FAST COOL to set the freezer and refrigerator to the coldest temperature settings. Press FAST COOL again to return to the selected temperature set point.

NOTES:

■The Fast Cool icon will be illuminated while the refrigerator is in Fast Cool mode.

■The Fast Cool feature will turn off automatically after 24 hours.

Moisture Control

The moisture control feature turns on a heater to help reduce moisture on the door hinge seal. Use in humid environments or when you notice moisture on the door hinge seal. The refrigerator uses more energy when Moisture Control is ON.

NOTE: The moisture control icon will light up to indicate the feature is ON.

To turn on/off the moisture control feature:

■Internal Control Panel - Press and hold MOISTURE CONTROL for 3 seconds.

■External Control Panel - Press and hold LIGHT for 3 seconds.

Water Filter Status Light and Reset

The filter reset control allows you to restart the water filter status tracking feature each time you replace the water filter. See “Water Filtration System.”

■Press and hold WATER FILTER for 3 seconds, to reset the water filter status to Good. The water filter icon will turn blue.

Air Filter Status Light and Reset

The filter reset control allows you to restart the air filter status tracking feature each time you replace the air filter. See “Install Air Filter.”

■Press and hold AIR FILTER for 3 seconds, to reset the air filter status to Good. The air filter icon will turn blue.

Water Dispenser

(on some models)

IMPORTANT:

■Allow 3 hours for the refrigerator to cool down and chill water.

■Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

■The dispensing system will not operate when the refrigerator door is open.

Flush the Water System

Air in the water dispensing system can cause the water dispenser to drip. After connecting the refrigerator to a water source or replacing the water filter, flush the water system.

Flushing the water dispensing system forces air from the water line and filter and prepares the water filter for use. Additional flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

1.Using a sturdy container, depress and hold the water dispenser paddle for 5 seconds.

2.Release the dispenser paddle for 5 seconds.

3.Repeat steps 1 and 2 until water begins to flow.

4.Once water begins to flow, continue depressing and releasing the dispenser paddle (5 seconds on, 5 seconds off) until a total of 4 gal. (15 L) has been dispensed.

Dispense Water

IMPORTANT:

■The dispensing system will not operate when the refrigerator door is open.

■The display screen on the dispenser control panel will turn off automatically and enter “sleep” mode when the control buttons and dispenser paddles have not been used for 2 minutes or more. While in “sleep” mode, the first press of a control button will only reactivate the display screen, without changing any settings. After reactivation, changes to any settings can then be made. If no changes are made within 2 minutes, the display will re-enter “sleep” mode.

To dispense water:

1. Press a sturdy glass against the water dispenser paddle.

15

2. Remove the glass to stop dispensing.

Dispenser Light

When you use the dispenser, the light will automatically turn on. If you want the light to be on continuously, you may turn on the light. The light icon will illuminate when the light is ON.

ON: Press LIGHT quickly to turn on the dispenser light. OFF: Press LIGHT quickly to turn off the dispenser light.

NOTES:

■If you unintentionally press and hold the LIGHT button for 3 seconds or longer, you will turn on the Moisture Control

feature. If this happens, press and hold LIGHT for 3 seconds again to turn off the Moisture Control feature.

■The dispenser lights are LEDs that cannot be changed. If it appears that your dispenser lights are not working, see “Troubleshooting” for more information.

Dispenser Lock

The dispenser can be turned off for easy cleaning or to avoid unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the refrigerator, to the ice maker, or to the dispenser light. It simply deactivates the controls and dispenser paddles. To turn off the ice maker,

see “Ice Maker and Storage Bin.”

■Press and hold FAST COOL for 3 seconds to lock the dispenser.

■Press and hold FAST COOL for 3 seconds again to unlock the dispenser.

The lock icon will illuminate when the dispenser is locked.

Ice Maker

IMPORTANT: For models with a water filter, after connecting the refrigerator to a water source or replacing the water filter, fill and discard three full containers of ice to prepare the water filter for use.

Turning the Ice Maker On/Off

To turn ON the ice maker, simply lower the wire shut-off arm.

To manually turn OFF the ice maker, lift the wire shut-off arm to the OFF (arm up) position and listen for the click.

NOTE: Your ice maker has an automatic shutoff. As ice is made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shut-off arm to the OFF (arm up) position. Do not force the wire shut-off arm up or down.

Ice Storage Bin

1.Wash the ice storage bin with mild soap and warm water.

2.Slide the ice storage bin under the ice maker, and push it toward the back as far as it will go.

3.Lower the arm on the ice maker to the ON position.

NOTE: It usually takes approximately 24 hours for the ice maker to begin producing ice. You may notice the ice has an “off-taste.” If so, discard the first three batches of ice produced. After that the “off-taste” should be gone.

Ice Production Rate

■The ice maker should produce approximately 8 to 12 batches of ice in a 24-hour period. Allow 3 days to completely fill the ice container.

■To increase ice production, lower the freezer and refrigerator temperature. See “Using the Control(s).” Wait 24 hours between adjustments.

Remember

■The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

■Do not use anything sharp to break up the ice in the bin. This can cause damage to the ice storage bin and the dispenser mechanism.

■Do not store anything on top of or in the ice maker or ice storage bin.

REFRIGERATOR

FEATURES

NOTE: Your model may have some or all of these features.

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

16

Refrigerator Shelves

The shelves in your refrigerator are adjustable to match your individual storage needs.

Glass Shelves

To remove a shelf:

1.Remove items from the shelf.

2.Slide the shelf straight out to the stop.

3.Depending on your model, lift the back or front of the shelf past the stop. Pull the shelf out the rest of the way.

To replace a shelf:

1.Slide the back of the shelf into the track in the wall of the cabinet.

2.Guide the front of the shelf into the shelf track. Be sure to slide the shelf in all the way.

Foldaway Shelf (on some models)

To retract the foldaway shelf:

■Retract the foldaway section of the shelf by holding the front of the shelf with one hand and lifting up on the center front of the shelf. Then push back and down on the shelf until it slides beneath the back section of the shelf.

To replace the foldaway shelf:

■Replace the foldaway section of the shelf by holding the front of the shelf with one hand and pulling the center of the shelf until the foldaway section is returned to its full shelf position.

Pantry Drawer

Pantry Drawer

To remove and replace the pantry drawer:

1.Slide pantry drawer out to the stop.

2.Lift front of pantry drawer with one hand while supporting bottom of drawer with other hand. Slide drawer out the rest of the way.

3.Replace the drawer by sliding it back in fully past the drawer stop.

Pantry Drawer Cover

To remove and replace the pantry drawer cover:

1.Remove the pantry drawer.

2.From underneath, push up on the glass cover and pull it out.

3.Replace the pantry drawer cover by lowering it into place.

4.Replace the pantry drawer.

Pantry Drawer Control

The amount of air flowing through the pantry drawer affects the temperature inside the drawer.

The airflow control is located on the left side of the pantry drawer.

To adjust the airflow:

■Colder - Slide the control forward, toward the front of the pantry drawer. The airflow is open.

■Cold - Slide the control all the way toward the rear of the pantry drawer. The airflow is closed, as shown.

Crisper

Crisper Drawers

To remove and replace the crisper drawer:

1.Slide the crisper drawer straight out to the stop. Lift the front and slide the drawer out the rest of the way.

2.Replace the drawer by sliding the drawer in fully past the stop.

Crisper Cover

To remove and replace the glass crisper cover:

1.Pull the glass straight out.

2.Replace the glass by pushing it straight in.

Crisper Humidity Control (on some models)

You can control the amount of humidity in the moisture-sealed crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) lets moist air out of the crisper for best storage of fruits and vegetables with skins.

■Fruit: Wash, let dry and store in refrigerator in plastic bag or crisper. Do not wash or hull berries until they are ready to use. Sort and keep berries in original container in crisper, or store in a loosely closed paper bag on a refrigerator shelf.

■Vegetables with skins: Place in plastic bag or plastic container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of fresh, leafy vegetables.

17

■Leafy vegetables: Wash in cold water, drain and trim or tear off bruised and discolored areas. Place in plastic bag or plastic container and store in crisper.

Fresh Bin

(on some models)

To remove and replace the fresh bin:

1.Open the bin by grasping the top center lip of the bin and tilting the bin outward.

2.Remove the bin by grasping both sides of the bin and lifting the bin upward off the glides.

3.Replace the bin by sliding it back into its tilted position on the glides and then push it closed.

DOOR FEATURES

NOTE: Your model may have some or all of these features.

Condiment Bins

To remove and replace the condiment bins:

1.Tilt the bin by pulling it outward.

2.Remove the bin by lifting it upward off the glides.

3.Replace the bin by sliding it back onto the glides and then push it closed.

Half-Height Bin

(on some models)

To remove and replace the half-height bin: 1. Tilt the bin by pulling it outward.

2. Remove the bin by lifting it upward off the glides.

3. Replace the bin by sliding it back onto the glides and then push it closed.

18

REFRIGERATOR CARE

Cleaning

WARNING

Use nonflammable

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to avoid buildup of odors. Wipe up spills immediately.

IMPORTANT:

■Because air circulates between both sections, any odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To avoid odor transfer and drying out of food, wrap or cover foods tightly.

■For stainless steel models, stainless steel is corrosion-resistant and not corrosion-proof. To help avoid corrosion of your stainless steel, keep your surfaces clean by using the following cleaning instructions.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, muriatic acid, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on exterior surfaces (doors and cabinet), plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools.

1.Unplug refrigerator or disconnect power.

2.Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.

3.Clean the exterior surfaces.

Painted metal: Wash painted metal exteriors with a clean, soft cloth or sponge and a mild detergent in warm water. Rinse surfaces with clean, warm water and dry immediately to avoid water spots.

Stainless steel: Wash stainless steel surfaces with a clean, soft cloth or sponge and a mild detergent in warm water. Rinse surfaces with clean, warm water and dry immediately to avoid water spots.

NOTE: When cleaning stainless steel, always wipe in the direction of the grain to avoid cross-grain scratching.

4.There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.

If you need to clean the condenser:

■Remove the base grille.

■Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area of the condenser.

■Replace the base grille when finished.

5.Plug in refrigerator or reconnect power.

Changing the Light Bulbs

IMPORTANT:

■Not all appliance bulbs will fit your refrigerator. Be sure

to replace the bulb with an appliance bulb of the same size, shape and wattage.

■To ensure optimum refrigerator performance, replace light bulbs as soon as they burn out.

Refrigerator Compartment Light

The lighting located at the top of the refrigerator compartment never needs to be replaced. If the lights do not illuminate when the door is opened, call for assistance or service. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.

Freezer Compartment Light (on some models)

1.Unplug the refrigerator or disconnect power.

2.Remove the light shield (on some models).

■Top of the freezer compartment - Slide the light shield toward the back of the compartment to release it from the light assembly.

3.Replace the burned-out bulb with an appliance bulb(s) no greater than 25 watts.

4.Replace the light shield.

5.Plug in refrigerator or reconnect power.

19

TROUBLESHOOTING

First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call, refer to the warranty page in this manual and scan the code with your mobile device, or visit www.whirlpool.com/product_help.

In Canada, visit www.whirlpool.ca.

Contact us by mail with any questions or concerns at the address below:

In the U.S.A.:	In Canada:
Whirlpool Brand Home Appliances	Whirlpool Brand Home Appliances
Customer eXperience Center	Customer eXperience Centre
553 Benson Road	200 – 6750 Century Ave.
Benton Harbor, MI 49022-2692	Mississauga, Ontario L5N 0B7
Please include a daytime phone number in your correspondence.

Operation

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

PROBLEM	POSSIBLE CAUSES	SOLUTIONS
The refrigerator	Check electrical supply	Plug the power cord into a grounded 3 prong outlet.
will not operate
		Do not use an extension cord.
		Make sure there is power to the outlet. Plug in a lamp to see if
		the outlet is working.
		Reset a tripped circuit breaker. Replace any blown fuses.
		NOTE: If problems continue, contact an electrician.
	Check controls	Make sure the controls are turned on. See “Using the Controls.”
	New installation	Allow 24 hours following installation for the refrigerator
		to cool completely.
		NOTE: Adjusting the temperature controls to the coldest setting
		will not cool either compartment quicker.

20

	PROBLEM	POSSIBLE CAUSES	SOLUTIONS
	The motor seems	High-efficiency compressor and fans	This is normal. Larger, more efficient refrigerators run longer.
	to run too much
		The room or outdoor temperature	It is normal for the refrigerator to work longer under these
		is hot	conditions. For optimum performance, place the refrigerator
			in an indoor, temperature-controlled environment. See “Location
			Requirements.”
		A large amount of warm food has been	Warm food will cause the refrigerator to run longer until the air
		recently added	cools to the desired temperature.
		The door(s) are opened too frequently	Warm air entering the refrigerator causes it to run more.
		or for too long	Open the door less often.
		The refrigerator door or freezer drawer	Make sure the refrigerator is level. See “Door Closing and Door
		is ajar	Alignment.” Keep food and containers from blocking the door.
		The refrigerator control is set too cold	Adjust the refrigerator control to a less cold setting until the
			refrigerator temperature is as desired. See “Using the Controls.”
		The door or drawer gasket is dirty,	Clean or change the gasket. Leaks in the door seal will cause
		worn, or cracked	the refrigerator to run longer in order to maintain desired
			temperatures.
	The lights do not work	A light bulb is loose in the socket	Tighten or replace the light bulb. See “Changing the
		or burned out	Light Bulbs.”
		The dispenser light is set to OFF	On some models, the dispenser light will operate only when a
			dispenser paddle is pressed. If you want the dispenser light to
			stay on continuously, see “Water Dispenser.”
		The control is set to Sabbath mode	Turn off Sabbath mode. See “Using the Controls.”
		(on some models)

Noise

PROBLEM

The refrigerator seems noisy

Below are listed some normal sounds with explanations.

POSSIBLE CAUSES

SOLUTIONS

The compressor in your new refrigerator regulates temperature more efficiently while using less energy, and operates quietly. Due to the reduction in operating noise, you may notice more intermittent noises.

Sound of the compressor	High efficiency compressor and fans	This is normal. Larger, more
running longer than expected		efficient refrigerators run longer.
Pulsating/Whirring	Fans/compressor adjusting to optimize performance during	This is normal.
	normal compressor operation
Popping	Contraction/expansion of inside walls, especially during initial	This is normal.
	cool-down
Hissing/Dripping	Flow of refrigerant, or flow of oil in the compressor	This is normal.
Vibration	The refrigerator may not be steady	Adjust the leveling screws and lower the
		leveling foot firmly against the floor. See
		“Door Closing and Door Alignment.”

Rattling/Banging	Movement of the water lines against the refrigerator cabinet,
	or of items placed on top of the refrigerator cabinet

Move excess water line away from the refrigerator cabinet or fasten excess tubing to the cabinet. See “Connect the Water Supply,” or remove items from the top of the refrigerator.

Sizzling	Water dripping on the heater during defrost cycle	This is normal.
Water running/Gurgling	May be heard when ice melts during the defrost cycle and	This is normal.
	water runs into the drain pan
Buzzing	Heard when the water valve opens to fill the ice maker	This is normal.
Creaking/Cracking	May be heard as ice is being ejected from the ice maker mold	This is normal.
Ker-plunk	May be heard when the ice falls into the ice storage bin	This is normal.

21

Temperature and Moisture

PROBLEM	POSSIBLE CAUSES	SOLUTIONS
Temperature is too warm	The refrigerator has just been installed	Allow 24 hours following installation for the refrigerator
		to cool completely.
	Cooling is turned off	Turn on cooling. See “Using the Controls.”
	The controls are not set correctly	Adjust the controls a setting colder. Check the temperature
	for the surrounding conditions	in 24 hours. See “Using the Control(s).”
	The door(s) are opened often	Allows warm air to enter refrigerator. Minimize door openings
	or not closed completely	and keep doors fully closed.

A large load of food was recently added

Allow several hours for refrigerator to return to normal temperature.

	Temperature is too cold	The refrigerator air vent(s) are blocked	If the air vent located in the top, left, rear corner of the
	in the refrigerator/crisper		refrigerator compartment is blocked by items placed directly
			in front of it, the refrigerator will get too cold. Move items
			away from the air vent.
		The controls are not set correctly	Adjust the controls a setting warmer. Check the temperature
		for the surrounding conditions	in 24 hours. See “Using the Controls.”
		The ice storage bin is not in the correct	See “Ice Maker.”
		position
	Temperature is too cold	The control is not set correctly	Adjust the control setting. See “Refrigerator Features.”
	in the pantry drawers	for the items stored in drawer
	There is interior	The room is humid	A humid environment contributes to moisture buildup.
	moisture buildup
		The door(s) are opened often or not	Allows humid air to enter the refrigerator. Minimize door
	NOTE: Some moisture
		closed completely	openings and close doors completely.
	buildup is normal.
		The door is blocked open	Move food packages away from door.
		A bin or shelf is in the way	Push bin or shelf back into the correct position.
		Storing liquid in open containers	This adds humidity to the refrigerator interior. Keep all containers
			tightly covered.
	There is frost/ice buildup in	The doors are opened often or	Minimize door openings and keep doors fully closed.
	the freezer compartment	left open
		Poor door seal	Ensure door seals are making full contact with the refrigerator
			cabinet to allow for an adequate seal.
		Temperature controls are not	See “Using the Controls” for recommended
		set correctly	temperature settings.

22

Ice and Water

PROBLEM

The ice maker is not producing ice or is not producing enough ice

POSSIBLE CAUSES	SOLUTIONS
The refrigerator is not connected to	Connect refrigerator to water supply and turn water shutoff valve
a water supply or the water supply	fully open.
shutoff valve is not turned on
There is a kink in the water source line	A kink in the line can reduce water flow. Straighten the water
	source line.
The ice maker is not turned on	Make sure the ice maker is ON. See “Ice Maker.”
The refrigerator has just been installed	Wait 24 hours after ice maker installation for ice production
	to begin. Wait 3 days for full ice production.
The refrigerator door is not	Close the door firmly. If it does not close completely, see
closed completely	“The doors will not close completely.”
A large amount of ice was	Allow 24 hours for ice maker to produce more ice.
recently removed
An ice cube is jammed in the ice maker	Remove ice from the ejector arm with a plastic utensil.
ejector arm	NOTE: On some models, press the lever which opens the
	ice maker door to access the ejector arm.

		A water filter is installed on	Remove the water filter and operate the ice maker. If ice volume
		the refrigerator	improves, then the filter may be clogged or incorrectly installed.
			Replace filter or reinstall it correctly.
		A reverse osmosis water filtration	This can decrease water pressure. See “Water Supply
		system is connected to your cold	Requirements.”
		water supply
	The ice cubes are	The water shut-off valve is not	Turn the water shut-off valve fully open.
	hollow or small	fully open
	NOTE: This is an indication of
		There is a kink in the water source line	A kink in the line can reduce water flow. Straighten the water
	low water pressure.
			source line.
		A water filter is installed	Remove filter and operate ice maker. If ice quality improves, then
		on the refrigerator	the filter may be clogged or incorrectly installed. Replace filter or
			reinstall it correctly.
		A reverse osmosis water filtration	This can decrease water pressure. See “Water Supply
		system is connected to your cold	Requirements.”
		water supply
		Questions remain regarding	Call a licensed, qualified plumber.
		water pressure
	Off-taste, odor or gray color	Recently installed or replaced	Discard the ice and wash the ice storage bin. Flush the water
	in the ice or water	plumbing connections. (New plumbing	system with 4 gal. (15 L) of water. Allow 24 hours for the
		connections can cause discolored or	ice maker to make new ice, and discard the first 3 batches
		off-flavored ice and water.)	of ice produced.
		The ice has been stored too long	Discard ice. Wash ice storage bin. Allow 24 hours for ice maker
			to make new ice.
		The water has been stored too long	Dispense at least 1 qt (1 L) of water per week to maintain
			a fresh supply.
		Odor from stored food has transferred	Use airtight, moisture proof packaging to store food.
		to the ice
		There are minerals (such as sulfur)	A water filter may need to be installed to remove the minerals.
		in the water

There is a water filter installed on the refrigerator

Gray or dark discoloration in ice may indicate that the water filtration system needs additional flushing. Flush the water system after installing and before using a new water filter. See “Water Dispenser” for water filter flushing instructions.

The water filter needs to be replaced	Replace the disposable water filter at least every 6 months
	or when indicated. See “Water Filtration System.”

23

PROBLEM	POSSIBLE CAUSES	SOLUTIONS
The water dispenser will	The refrigerator is not connected to	Connect the refrigerator to the water supply and turn the water
not operate properly	a water supply or the water supply	shut-off valve fully open.
	shut-off valve is not turned on
	There is a kink in the water source line	A kink in the water line can reduce water flow from the water
		dispenser and result in hollow or irregular shaped ice. Straighten
		the water source line.
	The refrigerator has just been installed	Flush and fill the water system. See “Water Dispenser.”
	The water pressure to the house is not	The water pressure to the house determines the flow from
	at or above 30 psi (207 kPa)	the dispenser. See “Water Supply Requirements.”
	A reverse osmosis water filtration	A reverse osmosis water filtration system can decrease water
	system is connected to your cold	pressure. See “Water Supply Requirements.”
	water supply
	A water filter is installed	Remove filter and operate dispenser. If water flow increases, the
	on the refrigerator	water filter may be clogged or incorrectly installed. Replace filter
		or reinstall it correctly.
	The refrigerator door is not closed	Close the door firmly. If it does not close completely, see
	completely (on some models)	“The doors will not close completely.”
	The refrigerator doors were	Make sure the water dispenser wire/tube assembly has
	recently removed	been properly reconnected at the top of the refrigerator
		door. See “Remove and Replace Refrigerator Doors and
		Drawer Front.”
Water is leaking or dripping	The glass was not held under the	Hold the glass under the dispenser 2 to 3 seconds after
from the dispenser system	dispenser long enough	releasing the dispenser lever.
NOTE: A few drops of water
after dispensing is normal.
Water continues to drip	The refrigerator has just been installed	Flushing the water system removes the air from the lines which
from the dispenser beyond		causes the water dispenser to drip. Flush the water system.
the first few drops.		See “Water Dispenser.”
	The water filter was recently changed	Flushing the water system removes the air from the lines which
		causes the water dispenser to drip. Flush the water system.
		See “Water Dispenser.”

Water is leaking from the back of the refrigerator

The water line connections were not	See “Connect the Water Supply.”
fully tightened
Recently removed the doors and did	See “Remove and Replace Refrigerator Doors and
not fully tighten water line connection	Drawer Front.”

Water from the dispenser is warm

NOTE: Water from the dispenser is only chilled to 50°F (10°C).

The refrigerator has just been installed	Allow 24 hours after installation for the water supply
	to cool completely.
A large amount of water was	Allow 3 hours for the water supply to cool completely.
recently dispensed
Water has not been recently dispensed	The first glass of water may not be cool. Discard the first glass
	of water dispensed.
The refrigerator is not connected	Make sure the refrigerator is connected to a cold water pipe.
to a cold water pipe	See “Water Supply Requirements.”

24

Doors

WARNING

Use nonflammable

Failure to do so can result in death, explosion, or fire.

PROBLEM	POSSIBLE CAUSES	SOLUTIONS
The door(s) or drawer will	The door or drawer is blocked open	Move food packages away from door(s). Remove ice
not close completely		or other items which have fallen onto the floor of the
		freezer compartment.
	A bin or shelf is in the way	Push bin or shelf back into the correct position.
	Recently installed	Remove all packaging materials.
The doors are difficult	The door gaskets are dirty or sticky	Clean gaskets and contact surfaces with mild soap and warm
to open		water. Rinse and dry with soft cloth.
The doors appear to	The doors need to be aligned or the	See “Door Closing and Door Alignment.”
be uneven	refrigerator needs to be leveled
The doors do not open or	The refrigerator tilt needs to	Adjust the refrigerator tilt. See “Door Closing and
close as expected	be adjusted	Door Alignment.”

25

PERFORMANCE DATA SHEET

Water Filtration System

Model P8WB2L/P8RFWB2L Capacity 200 Gallons (757 Liters)

System tested and certified by NSF International against NSF/ANSI Standard 42, Standard 53, and Standard 401 for the reduction of contaminants specified on the Performance Data Sheet.

This system has been tested according to NSF/ANSI Standards 42, 53 and 401 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42, 53 and 401.

Substance Reduction	Influent Challenge Concentration	Maximum Permissable Product Water Concentration	Average% Reduction
Aesthetic Effects
Chlorine Taste/Odor	2.0 mg/L ± 10%	50% reduction	97.0%
Particulate Class I*	At least 10,000 particles/mL	85% reduction	>99.9%
Contaminant Reduction	Influent Challenge Concentration	Maximum Permissable Product Water Concentration	Average% Reduction
Lead: @ pH 6.5 / @ pH 8.5	0.15 mg/L± 10%	0.010 mg/L	>99.3% / 98.6%
Benzene	0.015 mg/L ± 10%	0.005 mg/L	93.8%
p-Dichlorobenzene	0.225 mg/L ± 10%	0.075 mg/L	99.8%
Carbofuran	0.08 mg/L ± 10%	0.040 mg/L	81.9%
Toxaphene	0.015 ± 10%	0.003 mg/L	>95%
Atrazine	0.009 mg/L ± 10%	0.003 mg/L	87.0%
Asbestos	107 to 108 fibers/L††	99%	>99%
Live Cysts†	50,000/L min.	99.95%	>99.99%
Turbidity	11 NTU ± 10%	0.5 NTU	96.9%
Lindane	0.002 ± 10%	0.0002 mg/L	>99.2%
Tetrachloroethylene	0.015 mg/L ± 10%	0.005 mg/L	96.6%
o-Dichlorobenzene	1.8 mg/L ± 10%	0.60 mg/L	92.3%
Ethylbenzene	2.1 mg/L ± 10%	0.70 mg/L	86.9%
1,2,4-Trichlorobenzene	0.210 mg/L ± 10%	0.07 mg/L	>99.8%
2,4 - D	0.210 mg/L ± 10%	0.07 mg/L	88.5%
Styrene	2.0 mg/L ± 10%	0.1 mg/L	99.6%
Toluene	3.0 mg/L ± 10%	1.0 mg/L	93.5%
Endrin	0.006 mg/L ± 10%	0.002 mg/L	81.7%
Atenolol	200 ± 20%	30 ng/L	95.7%
Trimethoprim	140 ± 20%	20 ng/L	96.1%
Linuron	140 ± 20%	20 ng/L	96.3%
Estrone	140 ± 20%	20 ng/L	95.3%
Nonylphenol	1400 ± 20%	200 ng/L	95.5%

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.75 gpm (2.84 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).

The compounds certified under NSF 401 have been deemed as “emerging compounds/incidental contaminants.” Emerging compounds/ incidental contaminants are those compounds that have been detected in drinking water supplies at trace levels. While occurring at only trace levels, these compounds can affect the public acceptance/perception of drinking water quality.

■It is important that operational, maintenance, and filter replacement requirements be carried out for the product to perform as advertised. Property damage can occur if all instructions are not followed.

■The disposable cartridge must be changed at least every 6 months.

■Use replacement filter P8RFWB2L, part #EDR1RXD1/ EDR1RXD1B. 2015 suggested retail price of $49.99 U.S.A./$49.99 Canada. Prices are subject to change without notice.

■The filter monitor system measures the amount of water that passes through the filter and alerts you when it is time to replace the filter. Refer to the “Using the Controls” or “Water Filtration System” section (in the User Instructions or User Guide) to learn how to check the water filter status.

■After changing the water filter, flush the water system. See “Water and Ice Dispensers” or “Water Dispenser” in the User Instructions or User Guide.

■These contaminants are not necessarily in your water supply. While testing was performed under standard laboratory conditions, actual performance may vary.

■The product is for cold water use only.

■The water system must be installed in compliance with state and local laws and regulations.

*Class I particle size: >0.5 to <1 um

†Based on the use of Cryptosporidium parvum oocysts ††Fibers greater than 10 um in length

® NSF is a registered trademark of NSF International.

■Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

EPA Est. No. 082047-TWN-001

■Refer to the “Warranty” section (in the User Instructions or User Guide) for the Manufacturer’s limited warranty, name and telephone number.

Application Guidelines/Water Supply Parameters

Water Supply	Potable City or Well
Water Pressure	30 - 120 psi (207 - 827 kPa)
Water Temperature	33° - 100°F (0.6° - 37.8°C)
Service Flow Rate	0.75 gpm (2.84 L/min) @ 60 psi

26