Whirlpool WRF560SEHW, WRF560SEHV, WRF560SEHZ, WRF560SMHB, WRF560SMHV Owner's Manual

...

0 (0)

REFRIGERATOR USER INSTRUCTIONS

INSTRUCTIONS D’UTILISATION DU

RÉFRIGÉRATEUR

THANK YOU for purchasing this high-quality product. Register your new refrigerator at www.whirlpool.com. In Canada, register your refrigerator at www.whirlpool.ca.

For future reference, please make a note of your product model and serial numbers. These can be located on the inside wall of the refrigerator compartment.

Model Number ___________________________ Serial Number_____________________________

Nous vous REMERCIONS d’avoir acheté ce produit de grande qualité. Enregistrer votre nouveau réfrigérateur au www.whirlpool.com. Au Canada, enregistrer votre réfrigérateur au www.whirlpool.ca.

Pour référence future, veuillez prendre en note les numéros de modèle et de série de votre produit. Ceux-ci se trouvent sur la paroi interne du compartiment de réfrigération.

Numéro de modèle ___________________________ Numéro de série_____________________________

Table of Contents/Table des matières

REFRIGERATOR SAFETY..............................................................	2
INSTALLATION INSTRUCTIONS...................................................	3
Unpack the Refrigerator...............................................................	3
Location Requirements.................................................................	4
Remove and Replace Refrigerator Doors and Drawer Front.......	4
Electrical Requirements................................................................	8
Water Supply Requirements.........................................................	8
Connect the Water Supply...........................................................	8
Handle Installation and Removal................................................	10
Door Closing and Door Alignment..............................................	11
FILTERS AND ACCESSORIES.....................................................	11
Water Filtration System..............................................................	11
Install Air Filter.............................................................................	12
Install Produce Preserver............................................................	12
Accessories.................................................................................	13
REFRIGERATOR USE...................................................................	13
Opening and Closing Doors.......................................................	13
Using the Controls......................................................................	14
Water Dispenser.........................................................................	15
Ice Maker....................................................................................	16
REFRIGERATOR FEATURES.......................................................	16
Refrigerator Shelves...................................................................	17
Pantry Drawer.............................................................................	17
Crisper.........................................................................................	17
DOOR FEATURES.........................................................................	18
Condiment Bins..........................................................................	18
Fresh Bin.....................................................................................	18
Half-Height Bin...........................................................................	18
Cleaning......................................................................................	19
Changing the Light Bulbs...........................................................	19
REFRIGERATOR CARE................................................................	19
TROUBLESHOOTING...................................................................	20
Operation....................................................................................	20
Noise...........................................................................................	21
Temperature and Moisture..........................................................	22
Ice and Water..............................................................................	23
Doors...........................................................................................	25
PERFORMANCE DATA SHEET....................................................	26
WARRANTY...................................................................................	27

SÉCURITÉ DU RÉFRIGÉRATEUR...............................................	28
Déballage du réfrigérateur..........................................................	29
Exigences d’emplacement.........................................................	30
Retrait et réinstallation des portes du réfrigérateur et de
l’avant du tiroir............................................................................	30
Spécifications électriques...........................................................	34
Spécifications de l’alimentation en eau......................................	34
Raccordement à la canalisation d’eau.......................................	34
Installation et retrait des poignées.............................................	36
Fermeture et alignement de la porte..........................................	37
FILTRES ET ACCESSOIRES........................................................	37
Système de filtration de l’eau.....................................................	37
Installation du filtre à air..............................................................	38
Installer le conservateur de produits frais....................................	38
Accessoires.................................................................................	39
UTILISATION DU RÉFRIGÉRATEUR...........................................	39
Ouverture et fermeture des portes.............................................	39
Utilisation des commandes........................................................	40
Distributeur d’eau.......................................................................	41
Machine à glaçons......................................................................	42
CARACTÉRISTIQUES DU RÉFRIGÉRATEUR............................	43
Tablettes du réfrigérateur............................................................	43
Garde-manger.............................................................................	43
Bac à légumes............................................................................	43
CARACTÉRISTIQUES DE LA PORTE.........................................	44
Balconnets à condiments...........................................................	44
Balconnet pour aliments frais.....................................................	44
Balconnet mi-hauteur.................................................................	44
Nettoyage....................................................................................	45
ENTRETIEN DU RÉFRIGÉRATEUR.............................................	45
Remplacement des ampoules d’éclairage.................................	45
DÉPANNAGE.................................................................................	46
Utilisation....................................................................................	46
Bruit.............................................................................................	48
Température et humidité.............................................................	49
Glaçons et eau............................................................................	50
Portes..........................................................................................	52
FEUILLES DE DONNÉES SUR LA PERFORMANCE.................	53
GARANTIE.....................................................................................	54

W11363632A

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

many important safety messages in this manual and on your appliance. Always read and obey all safety

safety alert symbol.

alerts you to potential hazards that can kill or hurt you and others.

messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” mean:

DANGER WARNING

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

■Plug into a grounded 3 prong outlet.

■Do not remove ground prong.

■Do not use an adapter.

■Do not use an extension cord.

■Disconnect power before servicing.

■Replace all parts and panels before operating.

■Remove doors from your old refrigerator.

■Use nonflammable cleaner.

■This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

■Children should be supervised to ensure that they do not play with the appliance.

■If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard.

■Connect to a potable water supply only.

■Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

■Keep flammable materials and vapors, such as gasoline, away from refrigerator.

■Use two or more people to move and install refrigerator.

■Disconnect power before installing ice maker (on ice maker kit ready models only).

■Use a sturdy glass when dispensing ice (on some models).

■Do not hit the refrigerator glass doors (on some models).

■This appliance is intended to be used in household and similar applications such as:

-Staff kitchen areas in shops, offices and other working environments;

-Farm houses and by clients in hotels, motels and other residential type environments;

-Bed and breakfast type environments;

-Catering and similar non-retail applications.

SAVE THESE INSTRUCTIONS

Proper Disposal of Your Old Refrigerator

DANGER: Risk of child entrapment. Before you throw away your old refrigerator or freezer:

■Take off the doors.

■Leave the shelves in place so that children may not easily climb inside.

WARNING

Suffocation Hazard Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

– even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

■Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

■Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see “Refrigerator Safety.”

■Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the oor with cardboard or hardboard to avoid oor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as oor damage could occur.

Clean Before Using

After you remove all of the package materials, clean the inside of your refrigerator before using it. See the cleaning instructions in “Refrigerator Care.”

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-sized pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a 1/2" (1.25 cm) of space on each side and at the top. Allow for a 1" (2.54 cm) space behind the refrigerator. If your refrigerator

has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a fixed wall, leave a 2" (5.08 cm) minimum space between the refrigerator and wall to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

1/2" (1.25 cm)

2" (5.08 cm)

†TORX is a registered trademark of Acument Intellectual Properties, LLC.

Remove and Replace Refrigerator

Doors and Drawer Front

WARNING

Electrical Shock Hazard Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Depending on the width of your door opening, it may be necessary to remove the refrigerator doors to move the

refrigerator into your home.

Remove Doors and Hinges

IMPORTANT:

■If the refrigerator was previously installed and you are moving it out of the home, before you begin, turn the refrigerator control OFF, and unplug the refrigerator or disconnect power. Remove food and any adjustable door or utility bins from doors.

■Keep the refrigerator doors closed until you are ready to lift them free from the cabinet. Provide additional support for the refrigerator door while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

■All graphics referenced in the following instructions are included later in this section after “Final Steps.”

TOOLS NEEDED: 5/16", 3/8", and 1/4" hex head socket wrenches, Torx† T25 screwdriver, #2 Phillips screwdriver, and a

flat-blade screwdriver.

Remove Doors and Hinges

1.Unplug refrigerator or disconnect power.

2.Remove the base grille. Grasp the grille firmly and pull it toward you.

3.Starting with the right-hand side door, remove the parts for the top hinge as shown in Top Hinge graphic. Lift the refrigerator door from the bottom hinge pin.

4.Remove the hinge pin cover from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic.

5.Remove top hinge cover from the left-hand side refrigerator door. Remove the parts for the top hinge as shown in Top Hinge graphic.

External Dispenser Models Only:

■Disconnect the wiring plug, located under the top lefthand side door hinge, by wedging a flat-blade screwdriver or your fingernail between the two sections. See Wiring Plug graphic.

■Disconnect the water line, located under the top left-hand side door hinge, by pulling back on the locking collar while pulling the water line out of the water line connector. See Water Dispenser Tubing Connection graphic.

6.Lift the left-hand side door from the bottom hinge pin.

NOTE: On some models, remove the hinge pin cover from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic

Replace Doors and Hinges

WARNING

Excessive Weight Hazard

Use two or more people to lift the refrigerator door. Failure to do so can result in back or other injury.

4.Replace the base grille.

■Pull open the freezer drawer.

■Align the three clips on the back of the base grille with the three tabs at the base of the refrigerator.

■Push the base grille in toward the refrigerator until it is firmly in place.

1.Replace the parts for the bottom hinge as shown in Bottom Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

2.Assemble the parts for the top hinges as shown in Top Hinge graphic. Do not tighten the screws completely.

External Dispenser Models Only:

■Reconnect the wiring plug on top of the left-hand side refrigerator door.

■Reconnect the water line by pulling back the locking collar ring while firmly pushing the water line into the connector. Check for leaks.

3.Align the door so that the bottom of the refrigerator door aligns evenly with the top of the freezer drawer. Tighten all screws.

4.Replace the top hinge covers.

Remove and Replace Freezer Drawer Front

IMPORTANT: Two people may be required to remove and replace the freezer drawer. Graphics are included later in this section.

Remove Drawer Front

1.Open the freezer drawer to full extension.

2.Loosen the four screws attaching the drawer glides to the drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in the drawer front.

3.Lift drawer front upward and off the screws. See Drawer Front Removal graphic.

4.The refrigerator leveling/roller assembly protrudes from each side of the cabinet base. Remove the three screws attaching each assembly, and remove the assemblies. See Refrigerator Leveling/Roller Assembly graphic.

Replace Drawer Front

1.Align the leveling/roller assembly with the holes on each side of the refrigerator cabinet. Using the screws removed, reinstall the assemblies to the cabinet base. Tighten the screws completely.

2.Slide the drawer glides out of the freezer compartment. Insert the screws in the top of the drawer front into the slots in the drawer brackets. See Drawer Front Replacement graphic.

3.Pull the drawer brackets toward you to position the two screws in the bottom of the drawer front into the brackets. Completely tighten the four screws. See Drawer Front Replacement graphic.

A.Tab B. Clip

Final Steps

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1.Plug into a grounded 3 prong outlet.

2.Return all removable parts to doors and drawer and food to refrigerator and freezer.

Whirlpool WRF560SEHW, WRF560SEHV, WRF560SEHZ, WRF560SMHB, WRF560SMHV Owner's Manual

Style 1 - Non-Dispenser Models

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Door Removal and Replacement

Top Hinges

A. Hinge Cover Screw

B. Top Hinge Cover

C. 5/16" Hex-Head Hinge Screws

D. Top Hinge

Bottom Hinges

A. Hinge Pin Cover

B. Bottom Hinge

C. Hinge Screws

Leveling/Roller Assembly

A. Assembly Screws

Drawer Front Removal

Drawer Front Replacement

A. Loosen 4 Door Bracket Screws

Style 2 - External Water Dispenser Models

Door Removal and Replacement

Water Dispenser

Tubing Connection

A. Blue Outer Ring

Wiring Plug

Top Hinges

A.Hinge Cover Screw

B.Top Hinge Cover

C.5/16" Hex-Head Hinge Screws

D.Top Hinge

Bottom Hinges

A. Hinge Pin Cover

B. Bottom Hinge

C. Hinge Screws

Leveling/Roller Assembly

A. Assembly Screws

Electrical Requirements

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 V, 60 Hz, AC only 15 A or 20 A fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator and approved accessories be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person. Do not use a cord that shows cracks or abrasion damage along its length, or at either the plug or connector end.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn off Cooling, and then disconnect the refrigerator from the electrical source. When you have finished, reconnect the refrigerator to the electrical source and

turn on Cooling. See “Using the Control(s).”

Water Supply Requirements

A cold water supply with water pressure between 30 psi and 120 psi (207 kPa and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 psi and 120 psi (207 kPa and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 psi to 60 psi (276 kPa to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 psi to 60 psi (276 kPa to 414 kPa):

■Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

■Allow the storage tank on the reverse osmosis system to refill after heavy usage. The tank capacity could be too low to keep up with the requirements of the refrigerator.

■If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See “Water Filtration System.”

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

■Connect to potable water supply only.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

■All installations must meet local plumbing code requirements.

■Use copper tubing or Whirlpool supply line, Part Number 8212547RP, and check for leaks.

■Install copper tubing only in areas where the temperatures will remain above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

■	Flat-blade screwdriver	■	1/4" Nut driver
■	7/16" and 1/2" Open-end or	■	1/4" Drill bit
	2 adjustable wrenches	■	Cordless drill

NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or 3/16" (4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Connect to Water Line

Style 1

1.Unplug refrigerator or disconnect power.

2.Turn off main water supply. Turn on nearest faucet long enough to clear line of water.

3.Locate a 1/2" to 1¹⁄4" (1.25 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

■Make sure it is a cold water pipe.

■Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4.Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5.Using a cordless drill, drill a 1/4" hole in the cold water pipe you have selected.

	A
G	B
G
	C
F E	D
A. Cold water pipe	E. Compression sleeve
B. Pipe clamp	F. Shut-off valve
C. Copper tubing	G. Packing nut

D.Compression nut

6.Fasten the shut-off valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4" (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7.Slip the compression sleeve and compression nut onto the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

8.Place the free end of the tubing in a container or sink, and turn on the main water supply. Flush the tubing until water is clear. Turn off the shut-off valve on the water pipe. Coil the copper tubing.

Style 2

1.Unplug refrigerator or disconnect power.

2.Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator.

3.Thread the provided nut onto the water valve as shown.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

A.Bulb

B.Nut (provided)

4.Turn shut-off valve on.

5.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Connect to Refrigerator

Style 1

1.Unplug refrigerator or disconnect power.

2.Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten.

3.Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help avoid damage to the tubing when the refrigerator is pushed back against the wall.

4.Turn shut-off valve on.

5.Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

	A
	B
	C
	D
	E
A. Tube clamp	D. Compression nut
B. Tube clamp screw	E. Valve inlet

C.Copper tubing

6.On models with ice makers, the ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the 1/4" (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

Style 2

1.Unplug refrigerator or disconnect power.

2.Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator.

3.If the gray water tube supplied with the refrigerator is not long enough, a 1/4" x 1/4" (6.35 mm x 6.35 mm) coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

A	B	C	D	E F	G
A. Refrigerator water tubing			E. Ferrule (purchased)
B. Nut (provided)			F. Nut (purchased)
C. Bulb			G. Household water line

D.Coupling (provided)

4.Turn shut-off valve on.

5.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Complete the Installation

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

NOTES:

■Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

■For models with a water dispenser, flush the water system. See “Water Dispenser.”

Handle Installation and Removal

Parts Included: Refrigerator door handles (2),

Freezer drawer handle (1)

Tools Needed: 1/8" Hex key wrench

Install Door Handles

NOTE: Handle mounting setscrews are preinstalled inside the handle.

1.Remove the handles from the packaging inside the refrigerator.

2.Open a refrigerator door. On the opposite door, place the handle on the shoulder screws with the setscrews facing the adjacent door.

Install Drawer Handle

1.With the freezer drawer closed, place the handle on the shoulder screws with the setscrews facing down toward the floor.

A.Shoulder screws

B.Setscrews inside the handle

2.Firmly push the handle toward the drawer until the handle base is flush against the drawer.

3.Insert the short end of the hex key into the left-hand hole and slightly rotate the hex key until it is engaged in the setscrew.

A.Shoulder screws

B.Setscrews inside the handle

3.Firmly push the handle toward the door until the handle base is flush against the door.

4.While holding the handle, insert the short end of the hex key into the upper hole and slightly rotate the hex key until it is engaged in the setscrew.

5.Using a clockwise motion tighten the setscrew just until it begins to contact the shoulder screw. Do not fully tighten.

6.Repeat steps 4 and 5 to fasten the lower setscrew.

7.Once both setscrews have been partially tightened as instructed in the previous steps, fully tighten both setscrews

IMPORTANT: When the screws feel tight, tighten them an additional quarter-turn. The handle is not properly installed without this extra tightening.

8.Repeat steps 2 through 6 to install the other handle onto the adjacent refrigerator door.

4.Using a left-to-right motion tighten the setscrew a quarterturn at a time. Repeat until the screw feels tight.

5.Repeat steps 3 and 4 to fasten the right-hand setscrew to the shoulder screw.

6.Once both setscrews have been partially tightened as instructed in the previous steps, fully tighten both setscrews

IMPORTANT: When the screws feel tight, tighten them an additional quarter-turn. The handle is not properly installed without this extra tightening.

7.Save the hex key and all instructions.

Remove the Handles

1.While holding the handle, insert the short end of the hex key into a setscrew hole and slightly rotate the hex key until it is engaged in the setscrew.

2.Using a right-to-left motion loosen the setscrew a quarterturn at a time.

3.Repeat steps 1 and 2 for the other setscrew. Slowly pull the handle away from the door or drawer.

4.If necessary, use a Phillips screwdriver to remove the shoulder screws from the door.

Door Closing and Door Alignment

IMPORTANT: To comply with American Disabilities Act (ADA) guidelines, fully retract the rollers into the cabinet to lower the refrigerator.

Door Closing

The base grille covers the leveling screws and roller assemblies located at the bottom of the refrigerator cabinet below the freezer drawer. Before making adjustments, remove the base grille and move the refrigerator to its final location.

1.Remove the base grille. Grasp the grille firmly and pull it toward you.

2.Move the refrigerator to its final location.

NOTE: To allow the refrigerator to roll easier, raise the leveling legs off the floor by turning the leveling screws counterclockwise. The front rollers will be touching the floor.

3.So the doors will close easier, use a 1/4" hex driver to turn both leveling screws clockwise. This will raise the front of the refrigerator tilting it slightly downward to the rear. Turn both leveling screws the same amount.

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws. This makes it easier to turn the screws.

1/4"

■Push the base grille in toward the refrigerator until it is firmly in place

A.Tab B. Clip

Door Alignment

If the space between the refrigerator doors and freezer drawer looks uneven, you can adjust it using the following instructions:

1.Remove the top hinge cover.

2.Loosen the top hinge screws using a 5/16" socket or wrench.

3.Have someone hold the door in place or put a spacer between the doors and drawer.

4.Tighten the top hinge screws once the door is in the desired location.

5.Replace the top hinge cover.

A.Leveling screw

B.Front roller

4.Open both doors again to make sure they close as easily as you like and that they stay closed. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns.

NOTE: To keep the refrigerator level, you should turn both leveling screws the same amount.

5.Replace the base grille.

■Pull open the freezer drawer.

■Align the 3 clips on the back of the base grille with the 3 tabs at the base of the refrigerator.

FILTERS AND

ACCESSORIES

Water Filtration System

Water Filter Status Light

The water filter status light on the control panel will help you know when to order and replace the water filter.

■GOOD - The water filter icon on the control lights up in BLUE.

■ORDER a replacement filter - The water filter icon on the control lights up in YELLOW.

■REPLACE the water filter - The water filter icon on the control lights up in RED and “Replace Filter” will appear on the display.

■EXPIRED - The water filter icon lights up in RED and “Replace Filter” flashes on the display.

NOTE: If water flow to your water dispenser or ice maker decreases noticeably, change the filter sooner. The disposable water filter should be replaced at least every 6 months, depending on your water quality and usage.

■After changing the water filter, reset the status. Press and hold the Water Filter button for 3 seconds. When the system is reset, the water filter icon will return to BLUE and the words “Replace Filter” will disappear from the display.

Changing the Water Filter

1.Locate the water filter in the top-right corner of the refrigerator compartment.

2.Lift open the filter cover door. The filter will be released and then eject as the door is opened.

3.When the door is completely open, pull the filter straight out.

NOTE: There may be some water in the filter. Some spilling may occur. Use a towel to wipe up any spills.

4.Take the new filter out of its packaging and remove the covers from the O-rings. Be sure the O-rings are still in place after the covers are removed.

5.With the arrow pointing up, align the new filter with the filter housing and slide it into place. The filter cover door will automatically begin to close as the new filter is inserted.

6.Close the filter cover door completely in order to snap the filter into place. You may need to press hard.

7.Flush the water system. See “Water Dispenser” or “Water and Ice Dispensers.”

Install Air Filter

(on some models)

The air filter reduces the buildup of odors. This helps to maintain a cleaner environment inside the refrigerator.

On some models, your refrigerator's accessory packet includes an air filter, which must be installed prior to use. On some models, the air filter is already installed at the factory.

Installing the Air Filter

Install the air filter behind the vented door, located along the rear interior wall of the refrigerator compartment.

1.Remove the air filter from its packaging.

NOTE: An air filter status indicator is included with the air filter. The indicator is not needed for models that display the air filter status on the control panel.

2.Lift open the vented door.

3.Snap the filter into place.

Air Filter Status Indicator

The control panel displays the Air Filter status.

■GOOD - The air filter icon on the control panel lights up in BLUE.

■ORDER a replacement - The air filter icon on the control panel lights up in YELLOW.

■REPLACE air filter - The air filter icon on the control panel lights up in RED and “Replace Filter” will appear.

■EXPIRED - The air filter icon lights up in RED and “Replace Filter” flashes on the control panel.

After replacing the air filter, press and hold the Air Filter button for 3 seconds. The filter icons will turn off. See “Using the Control(s).” When the system is reset, the air filter icon will return to BLUE and the words “Replace Filter” will disappear from the control panel.

NOTE: At any filter status, pressing and holding the Air Filter button for 3 seconds will reset the air filter status to Good and the air filter icon will turn off.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months or when the status indicator air filter icon turns on and starts flashing when the refrigerator door is opened.

To order a replacement air filter, contact us. See “Accessories.”

1.Remove the used air filter by squeezing in on the side tabs.

2.Install the new air filter and reset the status indicator using the instructions in the previous section.

Install Produce Preserver

(on some models)

The produce preserver absorbs ethylene, to slow the ripening process of many produce items. As a result, certain produce items will stay fresh longer.

Ethylene production and sensitivity varies depending on the type of fruit or vegetable. To preserve freshness, it is best to separate produce with sensitivity to ethylene from fruits that produce moderate to high amounts of ethylene.

	Sensitivity to	Ethylene
	Ethylene	Production
Apples	High	Very High
Asparagus	Med.	Very Low
Berries	Low	Low
Broccoli	High	Very Low
Cantaloupe	Med.	High
Carrots	Low	Very Low
Citrus Fruit	Med.	Very Low
Grapes	Low	Very Low
Lettuce	High	Very Low
Pears	High	Very High
Spinach	High	Very Low

Installing the Produce Preserver

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia, bleach or acids. Do not get in eyes, on skin or clothing. Do not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium permanganate. If swallowed, call a Poison Control Center or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for 15 minutes. If on skin, rinse with water.

1. Find the Produce Preserver housing inside the refrigerator.

2.Open the housing by pulling up and out on the back.

3.Remove the Produce Preserver pouches from the packaging and place them into the housing.

NOTE: For best performance, always use 2 pouches.

4.Adhere the Produce Preserver housing to the back wall of the crisper drawer according to the instructions included in the package.

Installing the Status Indicator

The produce preserver comes with a status indicator, which should be activated and installed at the same time the pouches are installed.

1.Place the indicator face-down on a firm, flat surface.

2.Apply pressure to the bubble on the back of the indicator until the bubble pops to activate the indicator.

3.Slide open the cap on the top of the produce preserver housing.

4.Place the indicator in the top of the housing, facing outward.

5.Slide the cap closed, and check that the indicator is visible through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator’s bubble has not been popped.

Replacing the Produce Preserver

The disposable pouches should be replaced every 6 months or when the status indicator changes completely from white to red.

To order replacements, contact us. See “Accessories” for information on ordering.

1.Remove the used pouches from the produce preserver housing.

2.Remove the used status indicator.

3.Install the replacement pouches and status indicator using the instructions in the previous sections.

Accessories

The following accessories are available for your refrigerator. To order, contact us and ask for the part numbers.

In the U.S.A., visit our web page www.whirlpool.com/ accessories or call 1-800-901-2042.

In Canada, visit our web page www.whirlpool.ca or call 1-800-807-6777.

Affresh® Stainless Steel Cleaner:

Order Part #W10355016

Affresh® Stainless Steel Wipes:

Order Part #W10355049

Affresh® Kitchen & Appliance Cleaner:

Order Part #W10355010

Water Filter:

Order Part #W10295370A or FILTER1

Air Filter:

Order Part #W10311524 or AIR1

Produce Preserver:

Order Part #W10346771A or FRESH1

Water Filter, Air Filter and Ethylene Filter Bundle Pack:

Order Part #W103655758BL

REFRIGERATOR USE

Opening and Closing Doors

There are two refrigerator compartment doors. The doors can be opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

■When the left-hand refrigerator door is opened, the hinged seal automatically folds inward so that it is out of the way.

■When both doors are closed, the hinged seal automatically forms a seal between the 2 doors.

A. Hinged Seal

Using the Controls

IMPORTANT:

■Wait 24 hours for your refrigerator to cool completely before adding food. If you add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature controls to a colder than recommended setting will not cool the compartments any faster.

■The recommended setting should be correct for normal household refrigerator use. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.

■If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.

Control Panel

Depending on your model, your refrigerator has either an internal control panel, located at the top of the refrigerator compartment, or an external control panel, located above the external water dispenser. Follow the instructions specific to your model.

Internal Control Panel

External Control Panel

IMPORTANT (External Control only): The display screen on the dispenser control panel will turn off automatically and enter “sleep” mode when the control buttons and dispenser paddles have not been used for 2 minutes or more. While in “sleep” mode, the first press of a control button will only reactivate the display screen, without changing any settings. After reactivation, changes to any settings can then be made. If no changes are made within 2 minutes, the display will re-enter “sleep” mode.

■Touch any control button on the dispenser panel to activate the display screen.

Temperature Control

For your convenience, the temperature control is preset at the factory. When you first install your refrigerator, make sure the control is still set to the recommended setting as shown.

Recommended Setting “3 Snowflakes”

Adjusting the Controls

If you need to adjust the temperature in either the refrigerator or freezer compartment, use the settings listed in the following chart as a guide.

■Press the Temp button to display the desired number of snowflakes from 1 snowflake (least cold) to all

5 snowflakes (coldest).

NOTE: Except when starting the refrigerator, do not adjust the control more than one setting at a time. Wait 24 hours between adjustments for the temperature to stabilize.

CONDITION/REASON:	ADJUSTMENT:

REFRIGERATOR too warm	FRIDGE TEMP
	one more snowflake

FREEZER too warm/too little ice	FREEZER TEMP
	one more snowflake

REFRIGERATOR too cold	FRIDGE TEMP
	one less snowflake

FREEZER too cold	FREEZER TEMP
	one less snowflake

Cooling On/Off

Your refrigerator and freezer will not cool when cooling is turned off. Follow the directions specific to your model.

Internal Control Panel

■To turn cooling off, press and hold both the Fast Cool

and Moisture Control buttons at the same time for 3 seconds. When cooling is OFF, “Cooling Off” will appear on the display screen.

■To turn cooling back on, press and hold both the Fast Cool and Moisture Control buttons at the same time for 3 seconds. When cooling is ON, “Cooling Off” will disappear and the previously selected settings will appear on the display screen.

External Control Panel

■To turn cooling off, press and hold both the Freezer Temp and Fridge Temp buttons at the same time for 3 seconds. When cooling is off, “Cooling Off” will appear on the display screen.

■To turn cooling back on. Press and hold both the Freezer Temp and Fridge Temp buttons at the same time for 3 seconds. When cooling is on, “Cooling Off” will disappear and the previously selected settings will appear on the display screen.

Additional Features

Door Open Alarm

■The Door Open icon lights up whenever either door is opened.

■When either door is open for 5 minutes and cooling is on, an alert tone will sound three times, and the Door Open icon will flash seven times. This pattern will repeat every 2 minutes until all the doors are closed properly. The feature then resets and will reactivate when either door is left open again for 5 minutes.

NOTES:

■To mute the audible alarm while keeping the doors open, such as while cleaning the inside of the refrigerator, press any button on the control panel. The alarm sound will be temporarily turned off, but the Door Open icon will still be displayed on the dispenser control panel.

■Both doors must be fully closed to turn off the Door Open icon.

Fast Cool

The Fast Cool feature assists during times of high refrigerator use, full grocery loads or temporarily warm room temperatures.

■Press FAST COOL to set the freezer and refrigerator to the coldest temperature settings. Press FAST COOL again to return to the selected temperature set point.

NOTES:

■The Fast Cool icon will be illuminated while the refrigerator is in Fast Cool mode.

■The Fast Cool feature will turn off automatically after 24 hours.

Moisture Control

The moisture control feature turns on a heater to help reduce moisture on the door hinge seal. Use in humid environments or when you notice moisture on the door hinge seal. The refrigerator uses more energy when Moisture Control is ON.

NOTE: The moisture control icon will light up to indicate the feature is ON.

To turn on/off the moisture control feature:

■Internal Control Panel - Press and hold MOISTURE CONTROL for 3 seconds.

■External Control Panel - Press and hold LIGHT for 3 seconds.

Water Filter Status Light and Reset

The filter reset control allows you to restart the water filter status tracking feature each time you replace the water filter. See “Water

Filtration System.”

■Press and hold WATER FILTER for 3 seconds, to reset the water filter status to Good. The water filter icon will turn blue.

Air Filter Status Light and Reset

The filter reset control allows you to restart the air filter status tracking feature each time you replace the air filter. See “Install Air

Filter.”

■Press and hold AIR FILTER for 3 seconds, to reset the air filter status to Good. The air filter icon will turn blue.

Water Dispenser

(on some models)

IMPORTANT:

■Allow 3 hours for the refrigerator to cool down and chill water.

■Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

■The dispensing system will not operate when the refrigerator door is open.

Flush the Water System

Air in the water dispensing system can cause the water dispenser to drip. After connecting the refrigerator to a water source or replacing the water filter, flush the water system.

Flushing the water dispensing system forces air from the water line and filter and prepares the water filter for use. Additional

flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

1.Using a sturdy container, depress and hold the water dispenser paddle for 5 seconds.

2.Release the dispenser paddle for 5 seconds.

3.Repeat steps 1 and 2 until water begins to flow.

4.Once water begins to flow, continue depressing and releasing the dispenser paddle (5 seconds on, 5 seconds off) until a total of 4 gal. (15 L) has been dispensed.

Dispense Water

IMPORTANT:

■The dispensing system will not operate when the refrigerator door is open.

■The display screen on the dispenser control panel will turn off automatically and enter “sleep” mode when the control buttons and dispenser paddles have not been used for 2 minutes or more. While in “sleep” mode, the first press of a control button will only reactivate the display screen, without changing any settings. After reactivation, changes to any settings can then be made. If no changes are made within 2 minutes, the display will re-enter “sleep” mode.

To dispense water:

1. Press a sturdy glass against the water dispenser paddle.

2. Remove the glass to stop dispensing.

Dispenser Light

When you use the dispenser, the light will automatically turn on. If you want the light to be on continuously, you may turn on the light. The light icon will illuminate when the light is ON.

ON: Press LIGHT quickly to turn on the dispenser light. OFF: Press LIGHT quickly to turn off the dispenser light.

NOTES:

■If you unintentionally press and hold the Light button for 3 seconds or longer, you will turn on the Moisture Control

feature. If this happens, press and hold LIGHT for 3 seconds again to turn off the Moisture Control feature.

■The dispenser lights are LEDs that cannot be changed. If it appears that your dispenser lights are not working, see “Troubleshooting” for more information.

Dispenser Lock

The dispenser can be turned off for easy cleaning or to avoid unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the refrigerator, to the ice maker, or to the dispenser light. It simply deactivates the controls and dispenser paddles. To turn off the ice maker, see “Ice Maker and Storage Bin.”

■Press and hold FAST COOL for 3 seconds to lock the dispenser.

■Press and hold FAST COOL for 3 seconds again to unlock the dispenser.

The lock icon will illuminate when the dispenser is locked.

NOTE: Your ice maker has an automatic shutoff. As ice is made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shut-off arm to the OFF (arm up) position. Do not force the wire shut-off arm up or down.

Ice Storage Bin

1.Wash the ice storage bin with mild soap and warm water.

2.Slide the ice storage bin under the ice maker and push it toward the back as far as it will go.

3.Lower the arm on the ice maker to the ON position.

NOTE: It usually takes approximately 24 hours for the ice maker to begin producing ice. You may notice the ice has an “off-taste.” If so, discard the first 3 batches of ice produced. After that the “off-taste” should be gone.

Ice Production Rate

■The ice maker should produce approximately 8 to 12 batches of ice in a 24-hour period. Allow 3 days to completely fill the ice container.

■To increase ice production, lower the freezer and refrigerator temperature. See “Using the Control(s).” Wait 24 hours between adjustments.

Remember

■The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply

cannot be avoided, make sure the water softener is operating properly and is well maintained.

■Do not use anything sharp to break up the ice in the bin. This can cause damage to the ice storage bin and the dispenser mechanism.

■Do not store anything on top of or in the ice maker or ice storage bin.

Ice Maker

IMPORTANT: For models with a water filter, after connecting the refrigerator to a water source or replacing the water filter, fill and discard 3 full containers of ice to prepare the water filter for use.

Turning the Ice Maker On/Off

To turn on the ice maker, simply lower the wire shut-off arm.

To manually turn off the ice maker, lift the wire shut-off arm to the OFF (arm up) position and listen for the click.

REFRIGERATOR

FEATURES

NOTE: Your model may have some or all of these features.

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebblesize pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Refrigerator Shelves

The shelves in your refrigerator are adjustable to match your individual storage needs.

Glass Shelves

To remove a shelf:

1.Remove items from the shelf.

2.Slide the shelf straight out to the stop.

3.Depending on your model, lift the back or front of the shelf past the stop. Pull the shelf out the rest of the way.

To replace a shelf:

1.Slide the back of the shelf into the track in the wall of the cabinet.

2.Guide the front of the shelf into the shelf track. Be sure to slide the shelf in all the way.

Foldaway Shelf (on some models)

To retract the foldaway shelf:

■Retract the foldaway section of the shelf by holding the front of the shelf with one hand and lifting up on the center front of the shelf. Then push back and down on the shelf until it slides beneath the back section of the shelf.

To replace the foldaway shelf:

■Replace the foldaway section of the shelf by holding the front of the shelf with one hand and pulling the center of the shelf until the foldaway section is returned to its full shelf position.

Pantry Drawer

To remove and replace the pantry drawer:

1.Slide pantry drawer out to the stop.

2.Lift front of pantry drawer with one hand while supporting bottom of drawer with other hand. Slide drawer out the rest of the way.

3.Replace the drawer by sliding it back in fully past the drawer stop.

Pantry Drawer Cover

To remove and replace the pantry drawer cover:

1.Remove the pantry drawer.

2.From underneath, push up on the glass cover and pull it out.

3.Replace the pantry drawer cover by lowering it into place.

4.Replace the pantry drawer.

Pantry Drawer Control

The amount of air flowing through the pantry drawer affects the temperature inside the drawer.

The airflow control is located on the left side of the pantry drawer.

To adjust the airflow:

■Colder - Slide the control forward, toward the front of the pantry drawer. The airflow is open.

■Cold - Slide the control all the way toward the rear of the pantry drawer. The airflow is closed, as shown.

Crisper

Crisper Drawers

To remove and replace the crisper drawer:

1.Slide the crisper drawer straight out to the stop. Lift the front and slide the drawer out the rest of the way.

2.Replace the drawer by sliding the drawer in fully past the stop.

Crisper Cover

To remove and replace the glass crisper cover:

1.Pull the glass straight out.

2.Replace the glass by pushing it straight in.

Crisper Humidity Control (on some models)

You can control the amount of humidity in the moisture-sealed crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) lets moist air out of the crisper for best storage of fruits and vegetables with skins.

■Fruit: Wash, let dry and store in refrigerator in plastic bag or crisper. Do not wash or hull berries until they are ready to use. Sort and keep berries in original container in crisper, or store in a loosely closed paper bag on a refrigerator shelf.

+ 39 hidden pages