Page 1
PRODUCT MODEL NUMBERS
WET4024E, WET4027E
Dimensions/Clearances - 24" (61 cm)
Front View Side View
7
23
/8"
(606 mm)
703/4"
(1797 mm)
24" (61 cm) and 27" (69 cm)
Electric Washer/Dryer
7
/8"
35
653/4"
(1670 mm)
(911 mm)
1
20
/2"
(521 mm)
(1797 mm)
703/4"
1"
(25 mm)
1
/2"
43
(1105 mm)
111/2"
(292 mm)
1
/4"
34
(870 mm)
Back View
237/8"
(606 mm)
303/4"
(781 mm)
14"
(356 mm)
26"
(660 mm)
(1797 mm)
271/2"
(699 mm)
267/8"
(683 mm)
703/4"
37"
(940 mm)
1"
(25 mm)
1"
(25 mm)
W10761048A
05/2015
Page 2
(1822 mm)
271/4"
(692 mm)
713/4"
(1822 mm)
35
1
/4"
(895 mm)
41
1
/4"
(1,048 mm)
11"
(279 mm)
14"
(356 mm)
1"
(25 mm)
25"
(635 mm)
261/2"
(673 mm)
Dimensions/Clearances - 27" ( 69 cm)
Front View Side View
271/4"
(692 mm)
7
/8"
58
(1495 mm)
26"
(660 mm)
713/4"
1"
(25 mm)
653/4"
(1670 mm)
Back View
321/8"
(816 mm)
32"
(813 mm)
34"
(864 mm)
1"
(25 mm)
713/4"
(1822 mm)
2
Page 3
Clearances
24 in.
2
(155 cm2)
48 in.
2
(310 cm2)
3"
(76 mm)
3"
(76 mm)
Closet
door
Front
View
(25 mm/0 mm
Side Clearances Front/Back/Top
(recommended/minimum) (recommended/minimum)
12"
(305 mm)
Recessed area or closet installation
1"/0"
)
1"/0"
(25 mm/0 mm)
1"
(25 mm)
(Closet)
5"
(127 mm)
ELECTRICAL REQUIREMENTS
To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical
supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit
breaker is recommended. Connect to an individual branch circuit.
VENTING REQUIREMENTS
Exhaust venting: Exhaust your dryer to the outside. 4" (102 mm)
diameter vent is required. Rigid or flexible metal exhaust vent
must be used. Do not use plastic or metal foil vet. Exhaust hood
must be at least 12" (305 mm) from the ground or any object that
may be in the path of the exhaust.
Recommended Styles:
Acceptable Style:
The “Vent System Chart” provides venting requirements that
will help achieve best drying performance.
Vent System Chart, 24" Models
Number of
90° turns
or elbows
0 Rigid metal
1
2
Type
of vent
Rigid metal
Rigid metal
Box/louvered
hoods
43 ft. (13.1 m)
33 ft. (10.1 m)
23 ft. (7.0 m)
Angled
hoods
36 ft. (11.0 m)
26 ft. (7.9 m)
16 ft. (4.9 m)
Louvered hood
Box hood Angled hood
Vent System Chart, 27" Models
Number of
90° turns
Type
of vent
or elbows
0
1
2
Rigid metal
Rigid metal
Rigid metal
NOTE: Side exhaust installations have a 90º turn inside the
dryer. To determine maximum exhaust length, add one 90º
turn to the chart.
Box/louvered
hoods
37 ft. (11.3 m)
32 ft. (9.7 m)
23 ft. (7.0 m)
Angled
hoods
35 ft. (10.7 m)
27 ft. (8.2 m)
19 ft. (5.8 m)
3
Page 4
DRAIN SYSTEM
Drain system can be installed using a floor drain, wall standpipe,
floor standpipe, or laundry tub. Select method you need.
Floor standpipe drain system
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe
must be at least 39" (990 mm) high; install no higher than 96"
(2.4 m) from bottom of washer/dryer. If you must install higher
than 96" (2.4 m), you will need a sump pump system.
Wall standpipe drain system
See requirements for floor standpipe drain system.
Floor drain system
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285385), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. See “Use and Care Guide” for ordering
details. Minimum siphon break: 28" (710 mm) from bottom of
washer/dryer. (Additional hoses may be needed.)
Laundry tub drain system
Minimum capacity: 20 gal. (76 L). Top of laundry tub must be
at least 39" (990 mm) above floor; install no higher than 96"
(2.4 m) from bottom of washer/dryer.
IMPORTANT: To avoid siphoning, no more than 4.5" (113 mm)
of drain hose should be inside standpipe or below the top of
wash tub. Secure drain hose with shipping strap.
Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation
our products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice.
Loading...