Whirlpool WED8800YW, WED8200YW, W10398830A, W10398831A SP, WED8800YC User Manual

CABRIO®	SÉCHEUSE
ELECTRONIC DRYER	ÉLECTRONIQUE CABRIO®
USE AND CARE GUIDE	GUIDE D’UTILISATION
	ET D’ENTRETIEN

Table of Contents
DRYER SAFETY.............................................................	2
CHECK YOUR VENT SYSTEM
FOR GOOD AIR FLOW..................................................	4
CONTROL PANEL AND FEATURES.............................	5
CYCLE GUIDE................................................................	6
USING YOUR DRYER....................................................	8
ADDITIONAL FEATURES.................................................	10
DRYER CARE.....................................................................	11
TROUBLESHOOTING.......................................................	13
WARRANTY........................................................................	16
ASSISTANCE OR SERVICE...........................	Back Cover

Table des matières
SÉCURITÉ DE LA SÉCHEUSE....................................		17
VÉRIFICATION D’UNE CIRCULATION D’AIR
ADÉQUATE POUR LE SYSTÈME D’ÉVACUATION....		19
TABLEAU DE COMMANDE
ET CARACTÉRISTIQUES ...........................................		20
GUIDE DES PROGRAMMES.......................................		21
UTILISATION DE LA SÉCHEUSE................................		25
CARACTÉRISTIQUES SUPPLÉMENTAIRES..............		27
ENTRETIEN DE LA SÉCHEUSE.....................................		28
DÉPANNAGE......................................................................		31
GARANTIE...........................................................................		35
ASSISTANCE OU SERVICE..............	Couverture arrière

If you have any problems or questions, visit us at www.whirlpool.com Pour tout problème ou question, consulter www.whirlpool.ca

Para obtener acceso al “Manual de uso y cuidado” en español, o para obtener información adicional acerca de su producto, visite: www.whirlpool.com.

W10398830A W10398831A - SP

DRYER SAFETY

2

3

CHECK YOUR VENT SYSTEM FOR GOOD AIR FLOW

Good air flow

Along with heat, dryers require good air flow to efficiently dry laundry. Proper venting will reduce your drying times and improve your energy savings. See “Installation Instructions”.

The venting system attached to the dryer plays a big role in good air flow.

Service calls caused by improper venting are not covered by the warranty and will be paid by the customer, regardless of who installed the dryer.

Maintain good air flow by:

νCleaning your lint screen before each load.

νReplace plastic or foil vent material with 4" (102 mm) diameter heavy, rigid vent material.

νUse the shortest length of vent possible.

νUse no more than four 90° elbows in a vent system; each bend and curve reduces air flow.

Good Better

νRemove lint and debris from the exhaust hood.

νRemove lint from the entire length of the vent system at least every 2 years. When cleaning is complete, be sure to follow the “Installation Instructions” supplied with your dryer for final product check.

νClear away items from in front of the dryer.

Use Eco Cycles for better fabric care and energy savings

Use the Eco Cycles to provide the most energy savings and enhanced fabric care from the dryer. During Eco Cycles, drying air temperature and moisture level are sensed in the load. This sensing occurs throughout the drying cycle and the dryer shuts off when the load reaches the selected dryness. Use the NORMAL dryness level to provide optimal energy savings.

With Timed Dry Cycles, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to over-drying. Use Timed Dry Cycles for the occasional damp load that needs a little more drying time or when using the drying rack.

Tips for getting the best performance from your steam dryer

νResults may vary depending on fabric. 100% cotton garments with wrinkle-free finish may yield better results than those without. 100% cotton items may require additional touching up after the Steam Cycle.

νUse of fabric softener sheet is not recommended with Steam Cycles. It may cause temporary staining on clothes.

νIt is not recommended to use Steam Cycles for items that have been starched. Wash any starched or new garments prior to using a Steam Cycle.

νThe Enhanced Touch Up cycle is best for reducing odors and light wrinkles in small to medium-sized loads of dry garments. For the Enhanced Touch Up cycle, dry time automatically adjusts as load size is sensed. Cycle run time cannot be manually adjusted.

νThe Quick Refresh (on some models) cycle is best for reducing wrinkles and odors in dry garments, including loads left in the dryer. For, Quick Refresh time is selectable in five minute increments based on the load to be refreshed.

4

CONTROL PANEL AND FEATURES

1				2			3					4		5	6

Not all features and cycles are available on all models.

1 POWER BUTTON

Press to turn the dryer on and off. Press again to stop/cancel a cycle at any time.

2 CYCLE CONTROL KNOB

Use your dryer’s cycle control knob to select available cycles on your dryer. Turn the knob to select a cycle for your laundry load. See “Cycle Guide” for detailed descriptions of cycles.

3 EST. TIME REMAINING DISPLAY

When you select a cycle, its default settings will light up and the Estimated Time Remaining (for Automatic Cycles) or actual time remaining (for Manual Cycles) will be displayed.

4 DONE/SENSING DISPLAY

Done

This will indicate that the selected cycle has ended and the load may be removed from the dryer. If the Wrinkle Shield option has been selected, the dryer may continue to tumble the load, even if the DONE indicator is lit.

Sensing

At the beginning of an Automatic Cycle, the sensing light illuminates as the dryer senses the load size and adjusts for the appropriate dry time for that load. This indicator will not light during Timed Cycles or with options such as Wrinkle Shield™.

5ECO MONITOR

Your dryer is specially designed to conserve energy. Each cycle, along with selected options, will result in different energy usage, which will be displayed on the Eco Monitor bar, allowing you to choose the best energy usage for each load.

6START/PAUSE BUTTON

Press to start a cycle, or press once while a cycle is in process to pause it.

7CYCLE OPTIONS

Use these buttons to select available options for your dryer. Not all cycles and options are available on all models.

Eco Boost (on some models)

Press to activate Eco Boost option on select Automatic cycles. The Eco Boost option allows you to increase your energy savings with minimal impact on cycle dry times.

NOTE: Selecting the Eco Boost option adds 5 minutes to the default cycle time.

8

7

Static Reduce (on some models)

Press to add the Static Reduce option to select cycles (see Cycle Guide). The dryer will automatically tumble and spray to introduce a small amount of moisture into the load to help reduce static. This option adds approximately 8 minutes to the total cycle time.

Damp Dry Signal

When selected, a signal will sound during the drying cycle when the load is damp but not completely dry. This will allow you to take clothes out of the load that do not need to dry completely. This option is available on Heavy Duty, Normal, Sheets, Active Wear, Towels, Casual, Jeans, and Delicate cycles. It is a default option for the Bulky Items cycle.

Wrinkle Shield™/Wrinkle Shield™ with Steam (on some models)

If you will be unable to remove a load immediately, press WRINKLE SHIELD™ to add up to 140 minutes of periodic tumbling to help reduce wrinkling. On models with Wrinkle Shield™ with Steam, a short steam cycle is added after 60 minutes to help smooth out wrinkles.

Cycle Signal

Use this button to turn the signal indicating the end of a drying cycle on or off, or to adjust the volume of the signal.

Check Vent Indicator Light

The Check Vent indicator light will come on if a blocked vent or low airflow issue is detected. For more information on maintaining good airflow, see “Check Your Vent System for Good Airflow”.

8CYCLE MODIFIERS

Use these buttons to select available modifiers for your cycles. Not all cycles and modifiers are available on all models.

Dryness Level

You may adjust the Dryness Level on Automatic Cycles, if desired.

NOTE: The Dryness Level modifier is for use with Automatic Cycles only. Not available on the Sanitize cycle.

Temp

When using Manual Cycles only, you may select a dry temperature based on the type of load you are drying. Use the warmest setting safe for the

garments in the load. Follow garment label instructions.

NOTE: Automatic Cycles use a preset temperature that is not adjustable.

5

CYCLE GUIDE — AUTOMATIC CYCLES

Settings and options shown in bold are default settings for that cycle. Not all features and cycles are available on all models. Not all settings and options are available on each cycle. Default cycle times are estimated in minutes.

Use Automatic Cycles for better fabric care and energy savings

The dryer senses moisture in the load or air temperature and shuts off when the load reaches the selected dryness level.

Use the NORMAL dryness level to provide optimal energy savings. Use Automatic/Eco cycles on their default settings for optimal energy savings.

	Items to dry:	Cycle:	Drying	Dryness	Default	Available	Cycle Details:
			Temperature:	Level:	Time:	Options:
	Towels, bedding,	Sanitize	High	More	65	Wrinkle Shield†	Extended high-heat drying cycle
	children’s clothing						intended to help sanitize items such
							as bedding, towels, and baby wear.
							This cycle is not recommended for
							all fabrics. For best results, run cycle
							to completion, do not interrupt.
	Heavyweight items	Heavy Duty*	High	More	45	Damp Dry Signal	Offers stepped drying starting with
	such as towels or			Normal		Wrinkle Shield†	High heat, followed by Medium heat
	heavy work clothes			Less		Static Reduce	for enhanced fabric care and energy
				Damp		Eco Boost	savings.
	Jeans and denims	Jeans*	Medium	More	50	Damp Dry Signal	Stepped drying uses High heat
				Normal		Wrinkle Shield†	initially, followed by Medium heat
				Less		Static Reduce	to drive moisture from jeans and
				Damp		Eco Boost	denims.
	Large loads of cotton	Towels*	High	More	55	Damp Dry Signal	This is a long cycle with High heat
	towels, heavyweight			Normal		Wrinkle Shield†	to thoroughly dry towels. This cycle
	items			Less		Static Reduce	is not recommended for all fabrics.
				Damp		Eco Boost	Use for large loads of heavyweight
							fabrics such as cotton towels.
	Work clothes, casual	Normal*	Medium	More	38	Damp Dry Signal	Uses Medium heat to dry large loads
	wear, mixed cottons,			Normal		Wrinkle Shield†	of mixed fabrics and items. Normal
	sheets, corduroys			Less		Static Reduce	is the preferred energy cycle.
				Damp		Eco Boost
	Shirts, blouses,	Perm press/	Low	More	35	Damp Dry Signal	Uses a stepped drying temperature
	permanent press,	Casual*		Normal		Wrinkle Shield†	from Medium heat to Low heat for
	synthetics,			Less		Static Reduce	improved moisture removal and
	lightweight items			Damp		Eco Boost	enhanced fabric care.
	Jackets, comforters,	Bulky Items*	Medium	More	55	Damp Dry Signal	Use for drying large, bulky items;
	fiberfill pillows			Normal		Wrinkle Shield†	do not overfill dryer drum. Partway
				Less		Eco Boost	through the cycle, the signal
				Damp			will sound to indicate when it
							is time to rearrange items for
							optimal drying.
	Sheets, lightweight	Sheets*	Medium	More	40	Damp Dry Signal	Uses Medium heat to dry sheets
	linens			Normal		Wrinkle Shield†	and lightweight linens.
				Less		Static Reduce
				Damp		Eco Boost
	Performance fabrics,	Active Wear*	Extra Low	More	39	Damp Dry Signal	Use for drying active wear and
	exercise wear			Normal		Wrinkle Shield†	performance fabrics that require
				Less		Static Reduce	special care.
				Damp		Eco Boost
	Undergarments,	Delicate*	Extra Low	More	28	Damp Dry Signal	Uses Extra Low heat to gently dry
	blouses, lingerie,			Normal		Wrinkle Shield†	delicate items.
	performance wear			Less		Static Reduce
				Damp		Eco Boost
†	Or Wrinkle Shield™ with Steam (on some models). Wrinkle Shield™ with Steam is available only with High and Medium Temp settings.
*	Automatic/Eco cycle
Load Size Recommendations
For best results, follow the wet load size recommendations noted for					Medium load: Fill the dryer drum up to about 1/2 full.
each cycle.
	Small load: Fill the dryer drum with 3-4 items,				Large load: Fill the dryer drum up to about 3/4 full.
	not more than 1/4 full.				Do not overload. Items need to tumble freely.

6

CYCLE GUIDE — MANUAL CYCLES

Settings and options shown in bold are default settings for that cycle. Not all features and cycles are available on all models. Not all settings and options are available on each cycle. Default cycle times are estimated in minutes.

Adjusting drying time on Timed Dry Cycles

When you select a Timed Dry Cycle, the default time appears in the display.

Use the Time Adjust buttons to increase

or decrease the time in 1 minute increments. Press and hold to change the time in 5 minute increments.

The maximum dry time is 90 minutes.

Selecting the Temp

A High heat setting may be used for drying heavyweight items such as towels and work clothes.

A Low to Medium heat setting may be used for drying medium-weight items such as sheets, blouses, dresses, underwear, permanent press fabrics, and some knits.

Use a no-heat (Air Only) setting for foam, rubber, plastic, or heat-sensitive fabrics.

Line dry bonded or laminated fabrics.

NOTE: If you have questions about drying temperatures for various loads, refer to the care label directions.

Items to dry:	Cycle:	Temp:	Default	Available	Cycle Details:
			Time:	Options:
Small loads and	Quick Dry	High	13	Wrinkle Shield†	For small loads of 3-4 items.
sportswear		Medium
		Low
		Extra Low
		Air Only
Any load	Timed Dry	High	40	Wrinkle Shield†	Use to dry items to a damp level for items that do
NOTE: Select Air		Medium			not require an entire drying cycle. Select a drying
Only to dry foam,		Low			temperature based on the type of fabrics in your
rubber, plastic, or		Extra Low			load. If you are unsure of the temperature to select
heat-sensitive		Air Only			for a load, select the lower setting rather than the
fabrics					higher setting.
Small to medium	Touch Up	High	20	Wrinkle Shield†	Use this setting to help smooth out wrinkles from
loads	(for non-steam	Medium			such items as garments packed in a suitcase or
	models)	Low			garments wrinkled from being left in the dryer.
		Extra Low
		Air Only

† Or Wrinkle Shield™ with Steam (on some models). Wrinkle Shield™ with Steam is available only with High and Medium Temp settings.

CYCLE GUIDE — STEAM CYCLES

Settings and options shown in bold are default settings for that cycle. Not all settings and options are available on each cycle.

Steam cycles are designed for use with dry loads to loosen wrinkles, reduce odors, and refresh fabrics.

Items to	Cycle:	Drying	Default	Available
refresh:		Temperature:	Time:	Options:	Cycle Details:
Mixed loads	Enhanced	High	22	Wrinkle Shield†	Use to reduce odors and light wrinkles from small to
	Touch Up	Medium		Static Reduce	medium-sized loads of dry items. Dry time will
					automatically adjust when the load size is sensed.
					Cycle run time cannot be manually adjusted.
					Temperature is selectable. Do not add dryer sheets.
Shirts, blouses,	Quick	Medium	12	Wrinkle Shield†	The Quick Refresh cycle is best for reducing light
and slacks	Refresh			Static Reduce	wrinkles and odors from dry garments, including
	(on some				loads left in the dryer. For the Quick Refresh cycle,
	models)				time is selectable in 5 minute increments, based on
					the load to be refreshed.

† Or Wrinkle Shield™ with Steam (on some models). Wrinkle Shield™ with Steam is available only with High and Medium Temp settings.

Load Size Recommendations

For best results, follow the load size recommendations noted for each cycle.

Small load: Fill the dryer drum with 3-4 items, not more than 1/4 full.

Medium load: Fill the dryer drum up to about 1/2 full.

Large load: Fill the dryer drum up to about 3/4 full. Do not overload. Items need to tumble freely.

7

USING YOUR DRYER

WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

1. Clean the lint screen

Clean the lint screen before each load. Pull the lint screen straight up. Roll lint off the screen with your fingers. Do not rinse or wash screen to remove lint. Wet lint is hard to remove. Push the lint screen firmly back into place.

For additional cleaning information, see “Dryer Care”.

2. Load the dryer

Open the door by pulling on the handle. Place laundry in the dryer. Add a dryer sheet to wet load, if desired. Close the door.

IMPORTANT: Do not overload the dryer. Items need to tumble freely. Overloading can lead to poor drying performance and may increase wrinkling and tangling.

3. Press POWER

Press the POWER button to turn on the dryer.

4. Select the desired cycle

Select the desired cycle for your load. See the “Cycle Guide” for more information about each cycle.

NOTE: Not all cycles are available on all models.

8

5. Adjust cycle modifiers, if desired			7. Press START/PAUSE to begin cycle

You may adjust different settings, depending on whether you have selected an Automatic Cycle, or Manual Cycle. See the “Cycle Guide” for detailed information.

NOTE: Not all options and settings are available with all cycles. Not all cycles are on all models.

Automatic Cycles:

You can select a different Dryness Level, depending on your load, by pressing the Dryness Level button. Selecting More, Normal, Less, or Damp automatically adjusts the Dryness Level at which the dryer will shut off. Once the Dryness Level is set, it cannot be changed without stopping the cycle.

Sensor cycles give the best drying in the shortest time. Drying time varies based on fabric type, load size, and dryness setting.

Timed Cycles:

When you select a Timed Cycle, the default time appears in the display. Use the Time

Adjust buttons to increase or decrease the time in 1 minute increments. Press and hold

to change the time in 5 minute increments.

The default temperature may be changed by pressing

the Temp button until the desired drying temperature lights up.

Steam Cycles:

Quick Refresh with Steam:

Reduces odors and light wrinkles from small to medium-sized loads of dry items. Use the Time Adjust buttons to select the time appropriate for the load you want to dry. Cycle time is adjustable in 5 minute increments.

Enhanced Touch Up with Steam:

This cycle is best for reducing wrinkles and odors from dry garments. Dry time will automatically adjust when the load size is sensed. Temperature is selectable.

6. Select any additional options

Add additional options such as Eco Boost, Static Reduce, and Wrinkle Shield™ (with or without Steam) by pressing the button for that option.

NOTE: Not all options and settings are available with all cycles.

Press and hold the START/PAUSE button to begin the cycle.

8. Remove garments promptly after cycle is finished

Promptly remove garments after cycle has completed to reduce wrinkling. If you will be unable to remove the load promptly, select the WRINKLE SHIELD™ option (with or without Steam) before pressing START/PAUSE.

Changing the Automatic Cycle settings to increase drying time

If all your loads on all Automatic Cycles are consistently not as dry as you would like or are too dry, you may change the default settings to increase or decrease the default Dryness Level.

The sensor drying settings on Automatic Cycles can be adjusted to adapt to different installations, environmental conditions or personal preference. This change is retained and will affect all of your Automatic Cycles, not just the current cycle/load.

There are 5 drying settings, they will appear in the time display:

01 Factory preset dryness level.

02 Slightly drier clothes, 15% more drying time.

03 Much drier clothes, 30% more drying time.

04 Much damper clothes, 30% less drying time.

05 Slightly damper clothes, 15% less drying time.

To change the drying settings:

NOTE: The settings cannot be changed while the dryer is running or paused. The dryer must be in standby mode (the Power button is off) to adjust the default settings.

1.Before starting a cycle, press and hold the TEMP button for 6 seconds.

2.Press the DRYNESS LEVEL button to select the dryness level shown in the time display: 01, 02, 03, 04, or 05.

3.Press START/PAUSE to save the new Dryness Level setting.

9

ADDITIONAL FEATURES

USING THE DRYING RACK

To obtain a drying rack for your dryer, follow the instructions included in your dryer drum. Remove and discard any packing material before use.

Use the Drying Rack for items that you do not want to tumble dry, such as sweaters and tennis shoes. When you use the drying rack, the drum continues to turn, but the rack remains stationary.

The drying rack is intended for use with the Timed Dry Cycles only. The drying rack cannot be used with any Automatic Cycles.

To use the drying rack:

IMPORTANT: Do not remove the lint screen. 1. Open dryer door.

2.Align the two hooks on the front of the drying rack with the holes in the dryer door opening and press down fully into holes. Rest the rear support on the dryer back ledge.

3.Place wet items on top of the drying rack. Allow space around items for air to circulate. The drying rack does not move, but the drum will rotate; be sure to leave adequate clearance between items and the inside

of the dryer drum. Make sure items do not hang over the edges or between drying rack grille.

4.Close the door.

5.Select Timed Dry. Select the Air Only, Low or Extra Low Temp setting. Items containing foam, rubber, or plastic must be dried on a clothesline or by using the Air Only Temp setting.

6.When the cycle is selected, the Estimated Time Remaining display shows the default time. You can change the actual time in the cycle by increasing or decreasing the cycle time.

7.Press START/PAUSE.

NOTE: Check the lint screen and remove any lint accumulated from items dried on the drying rack after the cycle is finished.

CHANGING THE DRUM LIGHT

The dryer light automatically turns on inside the dryer drum when you open the door.

To change the drum light:

1.Unplug dryer or disconnect power.

2.Open the dryer door. Locate the light bulb cover on the back wall of the dryer. Remove the screw located in the lower right corner of the cover. Remove the cover.

3.Turn bulb counterclockwise. Replace the bulb with

a 10-watt appliance bulb only. Replace the cover and secure with the screw.

4.Plug in dryer or reconnect power.

10

DRYER CARE

CLEANING THE DRYER LOCATION

Keep dryer area clear and free from items that would block the air flow for proper dryer operation. This includes clearing piles of laundry in front of the dryer.

CLEANING THE DRYER INTERIOR

To clean dryer drum

1.Use a mild hand dish detergent mixed at a low concentration with very warm water, and rub with a soft cloth.

2.Rinse well with a wet sponge or towel.

3.Tumble a load of clean clothes or towels to dry drum OR

Use a microfiber cloth and hot water in a spray bottle to clean the drum and a second microfiber towel to dry.

NOTE: Garments that contain unstable dyes, such as denim blue jeans or brightly colored cotton items, may discolor the rear of the dryer interior. These stains are not harmful to your dryer and will not stain future loads of clothes. Dry unstable dye items inside out to avoid transfer of dye.

REMOVING ACCUMULATED LINT

From inside the dryer cabinet

Lint should be removed every 2 years, or more often, depending on dryer usage. Cleaning should be done by a qualified appliance servicer.

From the Exhaust Vent

Lint should be removed every 2 years, or more often, depending on dryer usage.

CLEANING THE LINT SCREEN

Every load cleaning

The lint screen is located in the door opening of the dryer. The control panel has an indicator light to remind you to clean the lint screen after each load. A screen blocked by lint will increase drying time.

To clean:

1.Pull the lint screen straight up. Roll lint off the screen with your fingers. Do not rinse or wash screen to remove lint. Wet lint is hard to remove.

2. Push the lint screen firmly back into place.

IMPORTANT:

νDo not run the dryer with the lint screen loose, damaged, blocked, or missing. Doing so can cause overheating and damage to both the dryer and fabrics.

νIf lint falls off the screen into the dryer during removal, check the exhaust hood and remove the lint. See “Venting Requirements”.

As needed cleaning

Laundry detergent and fabric softener residue can build up on the lint screen. This buildup can cause longer drying times for your clothes, or cause the dryer to stop before

your load is completely dry. The screen is probably clogged if lint falls off while the screen is in the dryer.

Clean the lint screen with a nylon brush every 6 months, or more frequently, if it becomes clogged due to a residue buildup.

To wash:

1.Roll lint off the screen with your fingers.

2.Wet both sides of lint screen with hot water.

3.Wet a nylon brush with

hot water and liquid detergent. Scrub lint screen with the brush

to remove residue buildup.

4. Rinse screen with hot water.

5.Thoroughly dry lint screen with a clean towel. Reinstall screen in dryer.

11