Whirlpool WED85HEFBL, YWED85HEFC, WED92HEFC, WED85HEFW, WED77HEFW Dimension Guide
...
Dryer Dimensions
Front view: |
|
27" |
(686 mm)
383/4" Min.
(984 mm)
39" Max. (990 mm)
Side view:
Electric Dryer
PRODUCT MODEL NUMBERS
WED7505F, WED75HEF, WED7740F, WED77HEF, WED8540F, WED85HEF, WED90HEF, WED92HEF
Installation spacing for recessed area or closet installation
All dimensions show recommended and minimum spacing allowed.
■■ Additional spacing should be considered for ease of installation and servicing.
■■ Additional clearances might be required for wall, door, floor moldings, and dryer venting.
■■ Additional spacing should be considered on all sides of the dryer to reduce noise transfer.
■■ For closet installation with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.
■■ Companion appliance spacing should also be considered.
Recommended installation clearances (dryer only):
|
3" |
|
18" min. |
(76 mm) |
48 in.2 min. |
(457 mm) |
|
|
|
(310 cm2) |
0" - 5"* |
|
24 in.2 min. |
(0" - 127 mm) |
|
(155 cm2) |
|
|
3" |
0"–5"* |
|
(76 mm) |
|
|
|
(0 mm–127 mm) |
|
|
|
1"* |
1" |
|
(25 mm) |
|
|
(25 mm) |
|
|
|
Back view: |
|
|
|
|
|
|
|
61/2" |
|
|
|
|
|
|
|
|
|
|
|
|
|||
NOTE: Most |
|
|
|
|
|
|
(165 mm) |
||||
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
||
installations |
|
|
|
|
|
|
|
|
|
|
|
require a minimum |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
of 5" (127 mm) |
Power supply |
|
|
|
|
|
|||||
clearance behind |
cord/cable |
|
|
|
|
|
|||||
dryer for exhaust |
Water inlet |
|
|
|
|
|
|||||
297/8"* |
|||||||||||
vent with elbow. |
(Steam |
||||||||||
|
|
(759 mm) |
|||||||||
See “Venting |
models |
|
|
||||||||
|
|
|
|
|
|||||||
Requirements.” |
|
only) |
31/2"* |
|
|
||||||
|
Vent |
|
|
||||||||
|
|
|
|
|
|
(89 mm) |
|||||
3/4"* |
61/8"* |
|
(156 mm) |
||
(18 mm) |
||
143/8" |
||
*Approx. measurement. |
||
|
(365 mm) |
*0" (0 mm) spacing is allowed for straight-back venting only. For steam models only, inlet hose must not be kinked.
Minimum installation clearances (dryer only):
|
Front |
Sides |
Rear |
Top |
Recessed |
NA |
0" (0 mm) |
0" (0 mm)** |
0" (0 mm) |
Closet |
NA |
0" (0 mm) |
0" (0 mm)** |
0" (0 mm) |
Under |
NA |
1” (25 mm) |
0” (0 mm)** |
0” (0 mm) |
Counter |
|
|
|
|
**0" (0 mm) spacing is allowed for straight-back venting only.
Custom under counter installation:
W10868947A
10/2016
Loading...