Whirlpool EMZH3464 WS FH, EMZH3464 BR FH, AKF 803 AV, AKF 803/02, EMZH3463 IN User Manual

CONTENTS			GB
INSTALLATION	PAGE 16
ELECTRICAL CONNECTION	PAGE 18
BEFORE USING THE APPLIANCES	PAGE 19
PROTECTING THE ENVIRONMENT	PAGE 19
PRECAUTIONS AND GENERAL
RECOMMENDATIONS	PAGE 19
ENERGY SAVING TIPS	PAGE 20
OVEN ACCESSORIES	PAGE 21
COOKTOP ACCESSORIES	PAGE 21
OVEN FUNCTIONS	PAGE 22
COOKTOP FUNCTIONS	PAGE 23
CLEANING THE OVEN AND ITS ACCESSORIES	PAGE 23
CARE AND MAINTENANCE OF CONVENTIONAL
ELECTRIC COOKTOPS	PAGE 25
CARE AND MAINTENANCE OF
THE GLASS-CERAMIC COOKTOP	PAGE 25
TROUBLESHOOTING GUIDE	PAGE 25
AFTER SALES SERVICE	PAGE 26
DECLARATION OF CONFORMITY CE	PAGE 26

15

INSTALLATION

Technical information for the installer

OVEN

•After removing the oven from its packaging, before making the connections place it on the polystyrene foam base to protect it from damage.

•Do not attempt to lift the oven by the handle.

Lift at the sides as shown in the figure (see arrow).

•Check that the appliance has not been damaged in transit.

•Oven dimensions and kitchen unit dimensions are shown in the figure opposite.

•Kitchen units in contact with the oven must be heat resistant (80°C).

•If plastic laminates or cement are not sufficiently heat-resistant, warping, bubbling or detachment of the finish may result.

•Install the oven in the housing, lifting it at the sides, taking care not to trap the wires of the electrical supply cable.

• For correct ventilation, follow the ventilation	No Contacts
opening directions shown in the figure
(500 x 80 mm min). An additional opening of 5 mm
is required between the oven top rim and the
cooktop lower rim: this opening must not be closed
by strips or housing crosspieces.
• During oven installation, care must be taken to
ensure that the sides are not touching the front
edges of the housing or adjacent drawers and
doors (see picture).
• Carry out the electrical connections between
cooktop and oven (see “Electrical connection”).
• Secure the oven to the kitchen unit with screws (A)
as shown.

16

INSTALLATION

Cooktop

•The cooktop must be set into a worktop between 20 mm and 50 mm thick.

There must be nothing between the cooktop and the oven (cross rails, brackets, etc.).

•If the cooktop is to be installed next to a column unit, leave a distance of at least 100 mm from the edge of the cooktop to the side of the column unit.

•Cut an opening in the worktop of the dimensions shown in the Product Description Sheet supplied separately.

•If not already present, fit the supplied seal to the cooktop flange after cleaning the contact area as shown in the top figure.

Cooktop with electric hotplates

•If the worktop is made of wood, fit the supplied clips.

1.Position the 4 spring clips (B) and fit them in their locations on the underside of the cooktop.

2.Fit the cooktop into the worktop.

•If the worktop is made of marble, plastic, ceramics, natural stone, etc., the cooktop must be secured with brackets (C) code

4819 310 18528 (to be requested from After Sales Service).

1.Position the brackets over the holes and secure them with the supplied screws.

2.Fit the cooktop into the worktop.

Glass-ceramic cooktop

N.B.: Remove the protective film before installing the cooktop.

•If the worktop is made of wood, use the supplied spring clips and screws.

1.Position the 4 clips (D) as shown and at the specified dimensions.

2.Secure the clips using screws (E).

3.Fit the cooktop into the worktop.

•If the worktop is made of marble, plastic, ceramics, natural stone, etc., the cooktop must be secured with brackets (F) code 4819 404 78697 (to be requested from After Sales Service).

1.Fit the cooktop into the worktop.

2.Position the 4 brackets (F) as shown in the figure, in accordance with the thickness of the worktop.

3.Fix the 4 screws (G) in holes (H).

17

ELECTRICAL CONNECTION

•Make sure the appliance is installed and connected to the electricity supply by a qualified technician in accordance with the manufacturer's instructions and in compliance with local regulations.

•The installer is responsible for the correct electrical connection of the appliances and the observance of the relative safety recommendations.

•The appliance must be connected to the electricity supply by means of an all-pole disconnect switch with minimum contact gap of 3 mm.

•The appliances must be earthed by law.

•Do not use multiple plug adapters or extension leads.

•After the oven has been installed, the electrical components must be concealed.

Connecting the oven to the power supply

•Make sure that the voltage shown on the rating plate is the same as the power supply voltage in your home. The service number is located on the front edge of the oven cavity (visible when the oven door is open).

•Use a type H05RR-F power cord (minum length: 800 mm).

•Warning: All the oven's components operate at 230-240V. When using a 400 V connection, make sure that the voltage reaching the oven is 230-240V, as illustrated in the side table.

Conductors X number		Electrical connection
1N+	~	H05 RR-F 3X4 mmq
2N+	~	H05 RR-F 4X2.5 mmq
3 +	~	H05 RR-F 4X2.5 mmq
3N+	~	H05 RR-F 5X1.5 mmq

Interconnecting cooktop and oven

•Before connecting the oven to the power supply, check that the cooktop is among the ones listed in the cooktop/oven pairing product sheet.

•Connect the 3 pole and 4 pole connectors to the respective connectors on the oven.

The 3 pole connectors (H) is located at the rear right hand side of the control panel, the 4 pole connector (J) is located at the top of the oven in the left hand corner (see figure).

•Connect the yellow/green striped earth wire ( ) (K) from the cooktop to the screw located near the 3 pole connector.

WARNING: DO NOT CONNECT TO THE POWER SUPPLY BEFORE YOU HAVE FINISHED CONNECTING THE OVEN AND THE COOKTOP.

•Mount the oven in the kitchen unit.

Make sure the power cord is not entrapped.

18