AKZ 232 AV
Whirlpool AKZ 232 AV, ESN3481 IN 01, AKZ 231 AV, EMZH 3460/01 WS, AKZ 207 User Manual
...
15
CONTENTS GB
INSTALLATION
PAGE
16
ELECTRICAL CONNECTION
PAGE
18
BEFORE USING THE APPLIANCES
PAGE
19
PROTECTING THE ENVIRONMENT
PAGE
19
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
PAGE
19
ENERGY SAVING TIPS
PAGE
20
OVEN ACCESSORIES
PAGE
21
COOKTOP ACCESSORIES
PAGE
21
OVEN FUNCTIONS
PAGE
22
COOKTOP FUNCTIONS
PAGE
23
CLEANING THE OVEN AND ITS ACCESSORIES
PAGE
23
CARE AND MAINTENANCE OF CONVENTIONAL
ELECTRIC COOKTOPS
PAGE
25
CARE AND MAINTENANCE OF THE
GLASS-CERAMIC COOKTOP
PAGE
25
TROUBLESHOOTING GUIDE
PAGE
25
AFTER SALES-SERVICE
PAGE
26
DECLARATION OF CONFORMITY CE
PAGE
26
53101Dgb.fm5 Page 15 Wednesday, February 21, 2001 10:50 AM
16
Technical information for the installer
OVEN
•
After removing the oven from its packaging, before
making the connections place it on the polystyrene
foam base to protect it from damage.
•
Do not attempt to lift the oven by the handle.
Lift at the sides as shown in the figure (see arrow).
•
Check that the appliance has not been damaged in
transit.
•
Oven dimensions and kitchen unit dimensions are
shown in the figure opposite.
•
Kitchen units in contact with the oven must be heat
resistant (80° C).
•
If plastic laminates or cement are not sufficiently
heat-resistant, warping, bubbling or detachment of
the finish may result.
•
Install the oven in the housing, lifting it at the sides,
taking care not to trap the wires of the electrical
supply cable.
•
For correct ventilation, follow the ventilation
opening directions shown in the figure
(500 x 80 mm min). An additional opening of 5 mm
is required between the oven top rim and the
cooktop lower rim: this opening must not be closed
by strips or housing crosspieces.
•
During oven installation, care must be taken to
ensure that the sides are not touching the front
edges of the housing or adjacent drawers and
doors (see picture).
•
Carry out the electrical connections between
cooktop and oven (see “Electrical connection”).
•
Secure the oven to the kitchen unit with screws (
A
)
as shown.
INSTALLATION
No Contacts
53101Dgb.fm5 Page 16 Wednesday, February 21, 2001 10:50 AM
17
Cooktop
• The cooktop must be set into a worktop
between 20 mm and 50 mm thick.
There must be nothing between the cooktop
and the oven (cross rails, brackets, etc.).
• If the cooktop is to be installed next to a
column unit, leave a distance of at least 100
mm from the edge of the cooktop to the side of
the column unit.
•
Cut an opening in the worktop of the dimensions
shown in the Product Description Sheet supplied
separately.
•
If not already present, fit the supplied seal to the
cooktop flange after cleaning the contact area as
shown in the top figure.
Cooktop with electric hotplates
• If the worktop is made of wood, fit the supplied
clips.
1.
Position the 4 spring clips (
B
) and fit them in their
locations on the underside of the cooktop.
2.
Fit the cooktop into the worktop.
• If the worktop is made of marble, plastic,
ceramics, natural stone, etc.,
the cooktop
must be secured with brackets (
C
) code
4819 310 18528 (to be requested from After Sales
Service).
1.
Position the brackets over the holes and secure
them with the supplied screws.
2.
Fit the cooktop into the worktop.
Glass-ceramic cooktop
N.B.:
Remove the protective film before installing the
cooktop.
• If the worktop is made of wood
, use the supplied
spring clips and screws.
1.
Position the 4 clips (
D
) as shown and at the
specified dimensions.
2.
Secure the clips using screws (
E
).
3.
Fit the cooktop into the worktop.
• If the worktop is made of marble, plastic,
ceramics, natural stone, etc.
, the cooktop must
be secured with brackets (
F
) code 4819 404 78697
(to be requested from After-Sales Service).
1.
Fit the cooktop into the worktop.
2.
Position the 4 brackets (
F
) as shown in the figure,
in accordance with the thickness of the worktop.
3.
Fix the 4 screws (
G
) in holes (
H
).
INSTALLATION
53101Dgb.fm5 Page 17 Wednesday, February 21, 2001 10:50 AM
18
Connecting the oven to the power supply
•
Make sure that the voltage shown on the rating
plate is the same as the power supply voltage in
your home. The service number is located on the
front edge of the oven cavity (visible when the
oven door is open).
•
Use a type H05RR-F power cord (minum length:
800 mm).
• Warning: All the oven’s components operate at
230-240V. When using a 400 V connection,
make sure that the voltage reaching the oven is
230-240V, as illustrated in the side table.
Interconnecting cooktop and oven
•
Before connecting the oven to the power supply,
check that the cooktop is among the ones listed in
the cooktop/oven pairing product sheet.
•
Connect the 3 pole and 4 pole connectors to the
respective connectors on the oven.
The 3 pole connectors (
H
) is located at the rear
right hand side of the control panel, the 4 pole
connector (
J
) is located at the top of the oven in the
left hand corner (see figure).
•
Connect the yellow/green striped earth wire ( )
(
K
) from the cooktop to the screw located near the
3 pole connector.
WARNING: DO NOT CONNECT TO THE
POWER SUPPLY BEFORE YOU HAVE
FINISHED CONNECTING THE OVEN AND
THE COOKTOP.
•
Mount the oven in the kitchen unit.
Make sure the power cord is not entrapped.
ELECTRICAL CONNECTION
Conductors X number Electrical connection
1N+
~
H05 RR-F 3X4 mmq
2N+
~
H05 RR-F 4X2.5 mmq
3+
~
H05 RR-F 4X2.5 mmq
3N+
~
H05 RR-F 5X1.5 mmq
• Make sure the appliance is installed and
connected to the electricity supply by a
qualified technician in accordance with
the manufacturer’s instructions and in
compliance with local regulations.
• The installer is responsible for the correct
electrical connection of the appliances
and the observance of the relative safety
recommendations.
• The appliance must be connected to the
electricity supply by means of an all-pole
disconnect switch with minimum contact
gap of 3 mm.
• The appliances must be earthed by law.
• Do not use multiple plug adapters or
extension leads.
• After the oven has been installed, the
electrical components must be
concealed.
53101Dgb.fm5 Page 18 Wednesday, February 21, 2001 10:50 AM
Loading...