Telefunken TSOP2256MQ1, TSOP2240MQ1, TSOP2237MQ1, TSOP2233MQ1, TSOP2230MQ1 Datasheet

TSOP22..MQ1

Vishay Telefunken

Photo Modules for PCM Remote Control Systems

Available types for different carrier frequencies

Type	fo	Type	fo
TSOP2230MQ1	30 kHz	TSOP2233MQ1	33 kHz
TSOP2236MQ1	36 kHz	TSOP2237MQ1	36.7 kHz
TSOP2238MQ1	38 kHz	TSOP2240MQ1	40 kHz
TSOP2256MQ1	56 kHz

Description

The TSOP22..MQ1 ± series are miniaturized receivers for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter.

The demodulated output signal can directly be decoded by a microprocessor. The main benefit is the reliable function even in disturbed ambient and the protection against uncontrolled output pulses.

16 080

Features

DPhoto detector and preamplifier in one package

DInternal filter for PCM frequency

DTTL and CMOS compatibility

DOutput active low

DImproved shielding against electrical field disturbance

DSuitable burst length ≥ 10 cycles/burst

Special Features

DSmall size package

DHigh immunity against disturbance light

DNo occurrence of disturbance pulses at the output

DShort settling time after power on (<200ms)

DContiunous data transmission possible ( 800 bursts/s)

Block Diagram

			2
Input		Control	VS
		Circuit	30 kW
			1
PIN			OUT
	AGC	Band	Demodu-
		Pass	lator
			3
			GND
14318
Document Number 82112			www.vishay.de •FaxBack [phone]
Rev. 3, 30-Mar-01			1 (7)

TSOP22..MQ1

Vishay Telefunken

Absolute Maximum Ratings

Tamb = 25_C

Parameter	Test Conditions	Symbol	Value	Unit
Supply Voltage	(Pin 2)	VS	±0.3...6.0	V
Supply Current	(Pin 2)	IS	5	mA
Output Voltage	(Pin 1)	VO	±0.3...6.0	V
Output Current	(Pin 1)	IO	5	mA
Junction Temperature		Tj	100	°C
Storage Temperature Range		Tstg	±25...+85	°C
Operating Temperature Range		Tamb	±25...+85	°C
Power Consumption	(Tamb x 85 °C)	Ptot	50	mW
Soldering Temperature	t x 10 s, 1 mm from case	Tsd	260	°C

Basic Characteristics

Tamb = 25_C

Parameter

Test Conditions

Symbol

Min

Typ

Max

Unit

Supply Current (Pin 2)

VS = 5 V, Ev = 0

ISD

0.8

1.1

1.5

mA

VS = 5 V, Ev = 40 klx, sunlight

ISH

1.4

mA

Supply Voltage (Pin 2)

VS

4.5

5.5

V

Transmission Distance

Ev = 0, test signal see fig.7,

d

35

m

IR diode TSAL6200, IF = 250 mA

Output Voltage Low (Pin 1)

I

OL

= 0.5 mA,E

e

= 0.7 mW/m2, f = f

V

250

mV

o

OL

Irradiance (30 ± 40 kHz)

Pulse width tolerance: t

pi

± 5/f

< t

po

E

0.2

0.4

mW/m2

o

e min

< tpi + 6/fo, test signal see fig.7

Irradiance (56 kHz)

Pulse width tolerance: t

pi

±5/f

< t

po

E

0.3

0.5

mW/m2

o

e min

< tpi +6/fo, test signal see fig.7

Irradiance

E

30

W/m2

e max

Directivity

Angle of half transmission distance

ϕ1/2

±45

deg

Application Circuit

	100 W *)	+5V
2	4.7 mF *)
TSOP22..MQ1
	>10 kW
TSAL62..	optional	mC
1
	**)
3		GND
16218

*) recommended to suppress power supply disturbances

**) The output voltage should not be hold continuously at a voltage below 3.3V by the external circuit.

www.vishay.de •FaxBack [phone]	Document Number 82112
2 (7)	Rev. 3, 30-Mar-01

TSOP22..MQ1

Vishay Telefunken

Suitable Data Format

The circuit of the TSOP22..MQ1 is designed in that way that unexpected output pulses due to noise or disturbance signals are avoided. A bandpassfilter, an integrator stage and an automatic gain control are used to suppress such disturbances.

The distinguishing mark between data signal and disturbance signal are carrier frequency, burst length and duty cycle.

The data signal should fullfill the following condition:

•Carrier frequency should be close to center frequency of the bandpass (e.g. 38kHz).

•Burst length should be 10 cycles/burst or longer.

•After each burst which is between 10 cycles and 70 cycles a gap time of at least 14 cycles is neccessary.

•For each burst which is longer than 1.8ms a corresponding gap time is necessary at some time in the data stream. This gap time should be at least 4 times longer than the burst.

•Up to 800 short bursts per second can be received continuously.

Some examples for suitable data format are:

NEC Code, Toshiba Micom Format, Sharp Code, RC5 Code, RC6 Code, R±2000 Code.

When a disturbance signal is applied to the TSOP22..MQ1 it can still receive the data signal. However the sensitivity is reduced to that level that no unexpected pulses will occure.

Some examples for such disturbance signals which are suppressed by the TSOP22..MQ1 are:

•DC light (e.g. from tungsten bulb or sunlight)

•Continuous signal at 38kHz or at any other frequency

•Signals from fluorescent lamps with electronic ballast with high or low modulation (see Figure A or Figure B).

0

5

10

15

20

time [ms]

Figure A: IR Signal from Fluorescent Lamp with low Modulation

0

5

10

15

20

time [s]

Figure B: IR Signal from Fluorescent Lamp with high Modulation

Document Number 82112	www.vishay.de •FaxBack [phone]
Rev. 3, 30-Mar-01	3 (7)