Telefunken TSOP2136TE1, TSOP2133TE1, TSOP2130TE1, TSOP2156TE1, TSOP2140TE1 Datasheet

TSOP21..TE1

Vishay Telefunken

Photo Modules for PCM Remote Control Systems

Available types for different carrier frequencies

Type	fo	Type	fo
TSOP2130TE1	30 kHz	TSOP2133TE1	33 kHz
TSOP2136TE1	36 kHz	TSOP2137TE1	36.7 kHz
TSOP2138TE1	38 kHz	TSOP2140TE1	40 kHz
TSOP2156TE1	56 kHz

Description

The TSOP21..TE1 ± series are miniaturized receivers for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter.

The demodulated output signal can directly be decoded by a microprocessor. The main benefit is the reliable function even in disturbed ambient and the protection against uncontrolled output pulses.

	16 080
Features
D Photo detector and preamplifier in one package	D Low power consumption
D Internal filter for PCM frequency	D High immunity against ambient light
D Improved shielding against electrical field	D Enhanced data rate of 2400 bit/s
disturbance	D Operation with short bursts possible
D TTL and CMOS compatibility	(≥ 6 cycles/burst)
D Output active low

Block Diagram

			2
Input		Control	VS
		Circuit	30 kW
			1
PIN			OUT
	AGC	Band	Demodu-
		Pass	lator
			3
			GND
14318

Document Number 82116	www.vishay.com
Rev. 4, 30-Mar-01	1 (8)

TSOP21..TE1

Vishay Telefunken

Absolute Maximum Ratings

Tamb = 25_C

Parameter	Test Conditions	Symbol	Value	Unit
Supply Voltage	(Pin 2)	VS	±0.3...6.0	V
Supply Current	(Pin 2)	IS	5	mA
Output Voltage	(Pin 1)	VO	±0.3...6.0	V
Output Current	(Pin 1)	IO	5	mA
Junction Temperature		Tj	100	°C
Storage Temperature Range		Tstg	±25...+85	°C
Operating Temperature Range		Tamb	±25...+85	°C
Power Consumption	(Tamb x 85 °C)	Ptot	50	mW
Soldering Temperature	t x 10 s, 1 mm from case	Tsd	260	°C

Basic Characteristics

Tamb = 25_C

Parameter

Test Conditions

Symbol

Min

Typ

Max

Unit

Supply Current (Pin 2)

VS = 5 V, Ev = 0

ISD

0.8

1.1

1.5

mA

VS = 5 V, Ev = 40 klx, sunlight

ISH

1.4

mA

Supply Voltage (Pin 2)

VS

4.5

5.5

V

Transmission Distance

Ev = 0, test signal see fig.8,

d

35

m

IR diode TSAL6200, IF = 250 mA

Output Voltage Low (Pin 1)

I

OL

= 0.5 mA,E

e

= 0.7 mW/m2, f = f

V

250

mV

o

OL

Irradiance (30 ± 40 kHz)

Pulse width tolerance: t

pi

± 5/f

< t

po

E

0.2

0.4

mW/m2

o

e min

< tpi + 5/fo, test signal see fig.8

Irradiance (56 kHz)

Pulse width tolerance: t

pi

± 5/f

< t

po

E

0.3

0.5

mW/m2

o

e min

< tpi + 5/fo, test signal see fig.8

Irradiance

E

30

W/m2

e max

Directivity

Angle of half transmission distance

ϕ1/2

±45

deg

Application Circuit

	100 W *)	+5V
2	4.7 mF *)
TSOP21..TE1
	>10 kW
TSAL62..	optional	mC
1
	**)
3		GND
16237

*) recommended to suppress power supply disturbances

**) The output voltage should not be hold continuously at a voltage below 3.3V by the external circuit.

www.vishay.com	Document Number 82116
2 (8)	Rev. 4, 30-Mar-01

TSOP21..TE1

Vishay Telefunken

Suitable Data Format

The circuit of the TSOP21..TE1 is designed in that way that unexpected output pulses due to noise or disturbance signals are avoided. A bandpassfilter, an integrator stage and an automatic gain control are used to suppress such disturbances.

The distinguishing mark between data signal and disturbance signal are carrier frequency, burst length and duty cycle.

The data signal should fullfill the following condition:

•Carrier frequency should be close to center frequency of the bandpass (e.g. 38kHz).

•Burst length should be 6 cycles/burst or longer.

•After each burst which is between 6 cycles and 70 cycles a gap time of at least 10 cycles is neccessary.

•For each burst which is longer than 1.8ms a corresponding gap time is necessary at some time in the data stream. This gap time should have at least same length as the burst.

•Up to 2200 short bursts per second can be received continuously.

Some examples for suitable data format are:

NEC Code, Toshiba Micom Format, Sharp Code, RC5 Code, RC6 Code, RCMM Code, R±2000 Code, RECS±80 Code.

When a disturbance signal is applied to the TSOP21..TE1 it can still receive the data signal. However the sensitivity is reduced to that level that no unexpected pulses will occure.

Some examples for such disturbance signals which are suppressed by the TSOP21..TE1 are:

•DC light (e.g. from tungsten bulb or sunlight)

•Continuous signal at 38kHz or at any other frequency

•Signals from fluorescent lamps with electronic ballast (an example of the signal modulation is shown in the figure below).

0

5

10

15

20

time [ms]

IR Signal from Fluorescent Lamp with low Modulation

Document Number 82116	www.vishay.com
Rev. 4, 30-Mar-01	3 (8)