Telefunken TSOP1540, TSOP1538, TSOP1537, TSOP1530, TSOP1536 Datasheet

...
TSOP15..
Vishay Telefunken
Photo Modules for PCM Remote Control Systems
Available types for different carrier frequencies
Type fo Type fo TSOP1530 30 kHz TSOP1533 33 kHz TSOP1536 36 kHz TSOP1537 36.7 kHz TSOP1538 38 kHz TSOP1540 40 kHz TSOP1556 56 kHz
Description
The TSOP15.. – series are miniaturized receivers for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter. The demodulated output signal can directly be decoded by a microprocessor. The main benefit is the reliable function even in disturbed ambient and the protection against uncontrolled output pulses.
GND
V
S
OUT
94 8691
Features
D
Photo detector and preamplifier in one package
D
Internal filter for PCM frequency
D
Improved shielding against electrical field disturbance
D
TTL and CMOS compatibility
D
Output active low
D
Low power consumption
D
Suitable burst length 10 cycles/burst
Block Diagram
Input
PIN
AGC
Special Features
D
Improved directivity
D
Enhanced immunity against all kinds of disturbance light
D
No occurrence of disturbance pulses at the output
Control
Circuit
Band
Pass
Demodu-
lator
80 k
2
V
S
W
3
OUT
1
GND
94 8136
Document Number 82029
www.vishay.com
1 (7)Rev. 9, 30-Mar 01
TSOP15..
y()
Vishay Telefunken
Absolute Maximum Ratings
T
= 25_C
amb
Parameter Test Conditions Symbol Value Unit Supply Voltage (Pin 2) V Supply Current (Pin 2) I Output Voltage (Pin 3) V Output Current (Pin 3) I Junction Temperature T Storage Temperature Range T Operating Temperature Range T Power Consumption (T Soldering Temperature t x 10 s, 1 mm from case T
Basic Characteristics
T
= 25_C
amb
Parameter Test Conditions Symbol Min Typ Max Unit
Supply Current (Pin 2) VS = 5 V, Ev = 0 I
VS = 5 V, Ev = 40 klx, sunlight I Supply Voltage (Pin 2) V Transmission Distance Ev = 0, test signal see fig.7,
IR diode TSAL6200, IF = 300 mA Output Voltage Low (Pin 3) I
Irradiance (30 – 40 kHz) Pulse width tolerance:
Irradiance (56 kHz) Pulse width tolerance:
Irradiance tpi – 5/fo < tpo < tpi + 6/f Directivity Angle of half transmission distance ϕ
= 0.5 mA,Ee = 0.7 mW/m2,
OSL
f = fo, tp/T = 0.4
tpi – 5/fo < tpo < tpi + 6/fo,
test signal see fig.7
tpi – 5/fo < tpo < tpi + 6/fo,
test signal see fig.7
x 85 °C) P
amb
o
SD SH
S
d 35 m
V
OSL
E
e min
E
e min
E
e max
1/2
S
S
O
O
j
stg
amb
tot sd
–0.3...6.0 V
5 mA
–0.3...6.0 V
5 mA
100 –25...+85 –25...+85
50 mW
260
0.4 1.5 mA
1.0 mA
4.5 5.5 V
250 mV
0.25 0.38 mW/m
0.3 0.45 mW/m
30 W/m
±55 deg
°
C
°
C
°
C
°
C
2
2
2
Application Circuit
100 W *)
2
3
1
4.7 mF *) >10 k
optional
**)
W
m
C
GND
Document Number 82029
TSOP15..
TSAL62..
14375
*) recommended to suppress power supply disturbances **) The output voltage should not be hold continuously at a voltage below 3.3V by the external circuit.
www.vishay.com
2 (7)
+5V
Rev. 9, 30-Mar-01
Suitable Data Format
The circuit of the TSOP15.. is designed in that way that unexpected output pulses due to noise or disturbance signals are avoided. A bandpassfilter, an integrator stage and an automatic gain control are used to suppress such disturbances. The distinguishing mark between data signal and disturbance signal are carrier frequency, burst length and duty cycle.
The data signal should fullfill the following condition:
Carrier frequency should be close to center frequency of the bandpass (e.g. 38kHz).
Burst length should be 10 cycles/burst or longer.
After each burst which is between 10 cycles and 70
cycles a gap time of at least 14 cycles is neccessary.
For each burst which is longer than 1.8ms a corresponding gap time is necessary at some time in the data stream. This gap time should be at least 4 times longer than the burst.
TSOP15..
Vishay Telefunken
Up to 800 short bursts per second can be received continuously .
Some examples for suitable data format are: NEC Code (repetitive pulse), NEC Code (repetitive data), Toshiba Micom Format, Sharp Code, RC5 Code, RC6 Code, R–2000 Code.
When a disturbance signal is applied to the TSOP15.. it can still receive the data signal. However the sensitivity is reduced to that level that no unexpected pulses will occure.
Some examples for such disturbance signals which are suppressed by the TSOP15.. are:
DC light (e.g. from tungsten bulb or sunlight)
Continuous signal at 38kHz or at any other
frequency
Signals from fluorescent lamps with electronic ballast with high or low modulation (see Figure A or Figure B).
0 5 10 15 20
time [ms]
Figure A: IR Signal from Fluorescent Lamp with low Modulation
0 5 10 15 20
time [s]
Figure B: IR Signal from Fluorescent Lamp with high Modulation
Document Number 82029
www.vishay.com
3 (7)Rev. 9, 30-Mar 01
Loading...
+ 4 hidden pages