Telefunken TSOP2256VI1, TSOP2240VI1, TSOP2237VI1, TSOP2236VI1, TSOP2230VI1 Datasheet

TSOP22..VI1

Vishay Telefunken

Photo Modules for PCM Remote Control Systems

Available types for different carrier frequencies

Type fo Type fo
TSOP2230VI1 30 kHz TSOP2233VI1 33 kHz
TSOP2236VI1 36 kHz TSOP2237VI1 36.7 kHz
TSOP2238VI1 38 kHz TSOP2240VI1 40 kHz
TSOP2256VI1 56 kHz

Description

The TSOP22..VI1 – series are miniaturized receivers
for infrared remote control systems. PIN diode and
preamplifier are assembled on lead frame, the epoxy
package is designed as IR filter.
The demodulated output signal can directly be
decoded by a microprocessor. The main benefit is the
reliable function even in disturbed ambient and the
protection against uncontrolled output pulses.

Features

D

Photo detector and preamplifier in one package

D

Internal filter for PCM frequency

D

TTL and CMOS compatibility

D

Output active low

D

Improved shielding against electrical field
disturbance

D

Suitable burst length ≥10 cycles/burst

Block Diagram

Input

PIN

AGC

Special Features

D

Small size package

D

High immunity against disturbance light

D

No occurrence of disturbance pulses at the
output

D

Short settling time after power on (<200ms)

D

Contiunous data transmission possible
( 800 bursts/s)

Control

Circuit

Band
Pass

Demodu-

lator

30 k

16 080

2

V

S

W

1

OUT

3

GND

14318

Document Number 821 14

www.vishay.com

1 (7)Rev. 4, 30-Mar-01

TSOP22..VI1

Vishay Telefunken

Absolute Maximum Ratings

T

= 25_C

amb

Parameter Test Conditions Symbol Value Unit
Supply Voltage (Pin 2) V
Supply Current (Pin 2) I
Output Voltage (Pin 1) V
Output Current (Pin 1) I
Junction Temperature T
Storage Temperature Range T
Operating Temperature Range T
Power Consumption (T
Soldering Temperature t x 10 s, 1 mm from case T

Basic Characteristics

T

= 25_C

amb

Parameter Test Conditions Symbol Min Typ Max Unit
Supply Current (Pin 2) VS = 5 V, Ev = 0 I
Supply Current (Pin 2) VS = 5 V, Ev = 40 klx, sunlight I
Supply Voltage (Pin 2) V
Transmission Distance Ev = 0, test signal see fig.7, IR

diode TSAL6200, IF = 250 mA

Output Voltage Low (Pin 1) IOL = 0.5 mA,Ee = 0.7 mW/m2, f =

f

o

Irradiance (30 – 40 kHz) Pulse width tolerance: tpi – 5/fo <

tpo < tpi + 6/fo, test signal see fig.7

Irradiance (56 kHz) Pulse width tolerance: tpi –5/fo <

tpo < tpi +6/fo, test signal see fig.7
Irradiance E
Directivity Angle of half transmission distance ϕ

x 85 °C) P

amb

SD
SH

S

d 35 m

V

OL

E

e min

E

e min

e max

1/2

S

S

O

O

j

stg

amb

tot
sd

–0.3...6.0 V

5 mA

–0.3...6.0 V

5 mA

100
–25...+85
–25...+85

50 mW

260

0.8 1.1 1.5 mA

1.4 mA

4.5 5.5 V

250 mV

0.2 0.4 mW/m

0.3 0.5 mW/m

30 W/m

±45 deg

°

C

°

C

°

C

°

C

2

2

2

Application Circuit

100 W *)

2

1

4.7 mF *)
>10 k

W

optional

m

C

TSOP22..VI1

TSAL62..

**)

16217

3

*) recommended to suppress power supply disturbances
**) The output voltage should not be hold continuously at a voltage below 3.3V by the external circuit.

www.vishay.com

2 (7)

+5V

GND

Document Number 821 14

Rev. 4, 30-Mar-01

Suitable Data Format

The circuit of the TSOP22..VI1 is designed in that way
that unexpected output pulses due to noise or
disturbance signals are avoided. A bandpassfilter, an
integrator stage and an automatic gain control are
used to suppress such disturbances.
The distinguishing mark between data signal and
disturbance signal are carrier frequency, burst length
and duty cycle.

The data signal should fullfill the following condition:

• Carrier frequency should be close to center
frequency of the bandpass (e.g. 38kHz).

• Burst length should be 10 cycles/burst or longer.

• After each burst which is between 10 cycles and 70

cycles a gap time of at least 14 cycles is neccessary.

• For each burst which is longer than 1.8ms a
corresponding gap time is necessary at some time in
the data stream. This gap time should be at least 4
times longer than the burst.

• Up to 800 short bursts per second can be received
continuously .

TSOP22..VI1

Vishay Telefunken

Some examples for suitable data format are:
NEC Code, T oshiba Micom Format, Sharp Code, RC5
Code, RC6 Code, R–2000 Code.

When a disturbance signal is applied to the
TSOP22..VI1 it can still receive the data signal.
However the sensitivity is reduced to that level that no
unexpected pulses will occure.

Some examples for such disturbance signals which
are suppressed by the TSOP22..VI1 are:

• DC light (e.g. from tungsten bulb or sunlight)

• Continuous signal at 38kHz or at any other

frequency

• Signals from fluorescent lamps with electronic
ballast with high or low modulation (see Figure A or
Figure B).

0 5 10 15 20

time [ms]

Figure A: IR Signal from Fluorescent Lamp with low Modulation

0 5 10 15 20

time [s]

Figure B: IR Signal from Fluorescent Lamp with high Modulation

Document Number 821 14

www.vishay.com

3 (7)Rev. 4, 30-Mar-01