Schneider Electric NBWL0355A Service Manual

Installation and Quick

Configuration Manual

NetBotz® Room Monitor 355

NBWL0355/NBWL0355A

NBWL0356/NBWL0356A

990-3293E-001

Publication Date: 3/2018

APC by Schneider Electric Legal Disclaimer

The information presented in this manual is not warranted by the APC by Schneider Electric to be authoritative, error free, or complete. This publication is not meant to be a substitute for a detailed operational and site specific development plan. Therefore, APC by Schneider Electric assumes no liability for damages, violations of codes, improper installation, system failures, or any other problems that could arise based on the use of this Publication.

The information contained in this Publication is provided as is and has been prepared solely for the purpose of evaluating data center design and construction. This Publication has been compiled in good faith by APC by Schneider Electric. However, no representation is made or warranty given, either express or implied, as to the completeness or accuracy of the information this Publication contains.

IN NO EVENT SHALL APC BY SCHNEIDER ELECTRIC, OR ANY PARENT, AFFILIATE OR SUBSIDIARY COMPANY OF APC BY SCHNEIDER ELECTRIC OR THEIR RESPECTIVE OFFICERS, DIRECTORS, OR EMPLOYEES BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL, OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, CONTRACT, REVENUE, DATA, INFORMATION, OR BUSINESS INTERRUPTION) RESULTING FROM, ARISING OUT, OR IN CONNECTION WITH THE USE OF, OR INABILITY TO USE THIS PUBLICATION OR THE CONTENT, EVEN IF APC BY SCHNEIDER ELECTRIC HAS BEEN EXPRESSLY ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. APC BY SCHNEIDER ELECTRIC RESERVES THE RIGHT TO MAKE CHANGES OR UPDATES WITH RESPECT TO OR IN THE CONTENT OF THE PUBLICATION OR THE FORMAT THEREOF AT ANY TIME WITHOUT NOTICE.

Copyright, intellectual, and all other proprietary rights in the content (including but not limited to software, audio, video, text, and photographs) rests with APC by Schneider Electric or its licensors. All rights in the content not expressly granted herein are reserved. No rights of any kind are licensed or assigned or shall otherwise pass to persons accessing this information.

This Publication shall not be for resale in whole or in part.

Contents

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Information for the Room Monitor 355 . . . . . . . . . . . 1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Document Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Additional Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Additional Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

StruxureWare Certified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . 4

Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Install the Room Monitor 355 . . . . . . . . . . . . . . . . . . . . . . . . . 7

Electrical box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Ceiling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connect the Room Monitor 355 to Your Network . . . . . . . . 10

Power-over-Ethernet (PoE) injector . . . . . . . . . . . . . . . . 10

PoE-capable hub or switch . . . . . . . . . . . . . . . . . . . . . . 10

Connect Sensors to Sensor Ports . . . . . . . . . . . . . . . . . . . . 11

Adjust the Lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Room Monitor 355 Installation and Quick Configuration

Initial Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 13

Configure Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . 13

Gather network settings information . . . . . . . . . . . . . . . . 13

Obtain network settings using DHCP . . . . . . . . . . . . . . . 14

Configure network settings using a terminal emulator . . 14

Configure network settings using the

Serial Configuration Utility . . . . . . . . . . . . . . . . . . . . . . . 15

Install Advanced View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

The Configuration Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Access an Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Administrator account user ID and password . . . . . . . . . 17

Root account user ID and password . . . . . . . . . . . . . . . 17

Lost password recovery . . . . . . . . . . . . . . . . . . . . . . . . . 18

Web Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Advanced View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Quick Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Configure appliance settings . . . . . . . . . . . . . . . . . . . . . 19

Configure alert actions . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Clean the Room Monitor 355 . . . . . . . . . . . . . . . . . . 21

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Two-Year Factory Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . 23

Terms of warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Non-transferable warranty . . . . . . . . . . . . . . . . . . . . . . . 23

Exclusions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Warranty claims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Radio Frequency Interference. . . . . . . . . . . . . . . . . . . . . . . . 25

USA— FCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Canada—ICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Japan—VCCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Taiwan—BSMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Australia and New Zealand . . . . . . . . . . . . . . . . . . . . . . 26

European Union . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Room Monitor 355 Installation and Quick Configuration

Safety

Read the instructions carefully to become familiar with the equipment before trying to assemble, operate, service or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.

The addition of this symbol to a Danger or Warning safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided, can result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, can result in moderate injury.

NOTICE

Addresses practices not related to physical injury including certain environmental hazards, potential damage or loss of data.

Safety Information for the Room Monitor 355

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• No user serviceable parts inside. Refer servicing to qualified personnel.

• Use indoors in a dry location.

Failure to follow these instructions will result in death or serious injury.

Room Monitor 355 Installation and Quick Configuration

Introduction

The APC by Schneider Electric NetBotz® Room Monitor 355 functions as the central hardware appliance for a NetBotz security and environmental monitoring system. The Room Monitor 355 can be installed anywhere in a room and includes an integrated camera and internal sensors that monitor temperature, humidity, dew point, air flow, and motion. It also includes four sensor ports for connecting temperature, humidity, smoke, door, vibration, spot fluid, and third-party dry contact and 0 following features:

• Image processor that generates images up to 1280 x 1024 resolution, 24-bit color, and up to 30 frames per second.

NOTE: The maximum frame rate describes the maximum number of images that the camera imager is capable of producing each second. The actual frame rate is dependent on the amount of available bandwidth and current resolution.

• Image Size: 7.7 mm x 6.1 mm (9.82 mm diagonal = 0.39 in).

• Field of View: 64º (H) x 53º (V) for all resolutions.

• User adjustable and switchable industry-standard CS-mount lens. CS-mount permits access to hundreds of different general purpose and special purpose lenses.

ATTENTION: THE EQUIPMENT CONTAINS, AND THE SOFTWARE ENABLES, VISUAL RECORDING CAPABILITIES, THE IMPROPER USE OF WHICH MAY SUBJECT YOU TO CIVIL AND CRIMINAL PENALTIES. APPLICABLE LAWS REGARDING THE USE OF SUCH CAPABILITIES VARY BETWEEN JURISDICTIONS AND MAY REQUIRE AMONG OTHER THINGS EXPRESS WRITTEN CONSENT FROM RECORDED SUBJECTS. YOU ARE SOLELY RESPONSIBLE FOR INSURING STRICT COMPLIANCE WITH SUCH LAWS AND FOR STRICT ADHERENCE TO ANY/ALL RIGHTS OF PRIVACY AND PERSONALTY. USE OF THIS SOFTWARE FOR ILLEGAL SURVEILLANCE OR MONITORING SHALL BE DEEMED UNAUTHORIZED USE IN VIOLATION OF THE END USER SOFTWARE AGREEMENT AND RESULT IN THE IMMEDIATE TERMINATION OF YOUR LICENSE RIGHTS THEREUNDER.

–5 V sensors. The integrated camera includes the

Room Monitor 355 Installation and Quick Configuration

Document Overview

The NetBotz Room Monitor 355 Installation and Quick Configuration Manual describes how to install a NetBotz Room Monitor 355, how to

connect devices to the appliance, and how to configure network settings. After performing the configuration procedures in this manual, you can access your system through the software interface, perform additional configuration tasks, and begin monitoring the environment.

Additional Documentation

Unless otherwise noted, the following documentation is available on the applicable product page on the APC by Schneider Electric website, www.apc.com. To quickly find a product page, enter the product name or part number in the search field.

NetBotz Appliance User Guide: Includes all details for using, managing,

and configuring a NetBotz system with one of the following appliances: NetBotz Room Monitor 355 (NBWL0355/NBWL0355A), NetBotz Rack Monitor 450 (NBRK0450), NetBotz Room Monitor 455 (NBWL0455/ NBWL0455A), NetBotz Rack Monitor 550 (NBRK0550), or NetBotz Rack Monitor 570 (NBRK0570).

Additional Options

The following options are available for the Room Monitor 355. For more information about any of the options, contact your APC by Schneider Electric representative or the distributor from whom you purchased your APC by Schneider Electric product.

• Temperature Sensor (AP9335T)

• Temperature/Humidity Sensor (AP9335TH)

• NetBotz Spot Fluid Sensor (NBES0301)

• NetBotz Door Switch Sensor for Rooms or Third Party Racks (NBES0302)

• NetBotz Door Switch Sensor for APC by Schneider Electric Racks (NBES0303)

• NetBotz Dry Contact Cable (NBES0304)

• NetBotz 0–5 V Cable (NBES0305)

• NetBotz Vibration Sensor (NBES0306)

• NetBotz Smoke Sensor (NBES0307)

StruxureWare Certified

This product is certified for use in StruxureWare® systems.

Room Monitor 355 Installation and Quick Configuration

Physical Description



   





aem0 203a

Front

Item Description

Vented internal



sensors

Network link



LED

Vented opening for airflow, temperature, and humidity sensors.

Shows the status of the network connection. Blinks to indicate network traffic (green = connected at 10 Mbps; yellow = connected at 100 Mbps).

Power LED Indicates whether the unit is receiving power



Camera LED Blinks steadily when the integrated camera is active.



Alert LED Indicates the alert status of the system. When more than



(green = receiving power; dark = not receiving power).

one alert exists, the most severe will be indicated.

• Flashing once every eight seconds = Informational

• Flashing once every four seconds = Warning

• Flashing once every two seconds = Error

• Flashing once every second = Critical

• Flashing twice per second = Failure

Temperature



display

• Displays the current temperature from 0 to 99 in Centigrade or Fahrenheit. The Temperature reading comes from the internal temperature sensor. If the temperature exceeds 99, the display will flash 99.

• When the unit first receives power, displays the unique identifier number for one minute.

• If an alert exists, flashes at the same rate as the Alert LED.

• During a firmware upgrade, displays 88.

Lens housing Must be removed to change the focus of the integrated



camera.

Room Monitor 355 Installation and Quick Configuration

Rear



Item Description

Sensor ports



(4)

Used for connecting APC by Schneider Electric sensors, third-party dry-contact sensors, and standard third-party 0–5 V sensors. Third-party dry-contact state sensors require the NetBotz Dry Contact Cable (NBES0304). Standard third-party 0–5 V sensors require the NetBotz 0–5 V Sensor Cable (NBES0305).

10/100 Base-T



network port

Provides for a 10/100 Base-T network connection and power through Power-over-Ethernet (PoE). (The appliance operates at 100 Base-T only.) Status and link LEDs indicate network traffic:

• Status LED: blinks orange and green at start-up, then indicates the status of the network connection (solid green = IP address established; blinking green = attempting to obtain an IP address).

• Link LED: blinks to indicate network traffic (green = connected at 10 Mbps; orange = connected at 100 Mbps).

USB port Used to configure the appliance.



Reset Used to restart the appliance.



Room Monitor 355 Installation and Quick Configuration

Inventory

ae m028 6b

Inspect the contents of the package to ensure that the parts included match those shown below. Report missing or damaged contents to APC by Schneider Electric or your APC by Schneider Electric reseller. However, if damage was due to shipping, immediately report the damage to the shipping agent.

The shipping and packaging materials are recyclable. Please save them for later use or dispose of them appropriately.

Item Description Item Description

Bracket mounting plate for



electrical boxes

Adhesive cable tie holders



Mounting screw wall anchors



13 mm (0.5 in) machine screws



(for electrical box)

19 mm (0.75 in) sheet metal



screws (for wall or enclosure)

T-bar mounting plate



203 mm (8 in) tie wrap



Room Monitor 355 Installation and Quick Configuration

Ball-joint adjuster arms



Extender arm set screw



Cable retainer



Allen wrench



Rubber bracket cover



Mounting plate



Extender arm



+ 22 hidden pages