Schneider Electric MPR-5600 Series, MPR-5700 Series Data Sheet

SPECIFICATIONS

Actuator Inputs

Control Circuit:

MPR-561X and -563X Series, Two-wire.

MPR-571X and -573X Serie Input Impedance: 82.5 Ω for 4 to 20 mA input. Power Input: Refer to Table-1 and Table Connections: Color-coded 4' (1.2 m) leads.

s, Three-wire.

-2.

Actuator Outputs

Electrical:

Position Signals, Internal feedback circuitry provides positive positioning of the damper

in relation to the controller signal.

Startpoint Adjustment, Adjustable potentiometer provide

actuator startpoint.

Mechanical:

Stroke,

Damper Approximately 2" (51 mm) from fully

AM-601 linkage).

Valve Approximately 9/16" (14.3 mm) from fully retracte

Nominal Damper Area, Actuator sizing should be done in accordance with damper

manufacturer’s specifications.

Output Torque Rating, The proportional o

available throughout the entire stroke and is based on the lowest force available under

normal operation, the spring return stroke, or at minimum (-10%) supply voltage.

retracted to fully extended (includes

utput torque rating of 15 lb-in. (1.7 N-m) is

s manual adjustment of the

d to fully extended.

Environment

Ambient Temperature Limits:

Shipping & Storage, -40 to 140° F (-40 to 60° C).

Operating,

Damper -20 to

Valve Refer to Table-3. Humidity Location: NEMA Type 1, indoor only.

Agency Listings:

UL 873: Underwriters Laboratorie

Regulating Equipment). CSA: Certified for use in Canada by Und C22.2 No. 24-93. European Community: EMC Directive (8 (72/23/EEC).

: 5 to 95% RH, non-condensing.

140° F (-29 to 60° C).

s (File # E9429 Category Temperature-Indicating and

erwriters Laboratories. Canadian Standard

9/336/EEC). Low Voltage Directive

Table-1 Model Chart for Valve (Basic) Actuators.

Timing in Seconds

@ 72 F (22 C)

No Load Stroke Retract

Extend Retract

Power

Loss

Required Linkages

Val ve

Applications

Damper

Applications

Part Number

Actuator Power Input

Voltage

+10/

Hz VA Watt

-15%

MPR-5610 120

MPR-5611 240

MPR-5613 24

MPR-5710

MPR-5711

120 Compatible

240

50/60 18 10 60 30 15

AV-600 AV-601

AM-601

MPR-5713 24

These MPR-5X1X series valve actuators are compatible with VB-7XXX 1/2" to 2" valve bodies.

The MPR-5X1X series actuators are basic models which may be equipped for damper applications wi h the installation of an AM-601 linkage.

May be required for steam and hot water. Refer to Table-3.

These actuators are obsolete. They are listed here for reference only.

Table-2 Model Chart for Damper Actuato

rs.

Actuator Power Input Timing in Seconds @ 72 F (22 C)

Part Number

Voltage

+10/

-15%

Hz VA Wa

tts

No Load Stroke

Extend Retract

Retract on

Power

Loss

Input

Signal

Inpu

Signal

Compatible with 4 to 20 mA

with 135 ¾ Slidewire (Series 90)

MPR-5630 120

Compatible

with

MPR-5633 24

MPR-5730

120 Compatible

50 60 18 10 60 30 15

4 to 20 mA

with

MPR-5733

135 ¾

Slidewire

(Series 90)

Damper models (MPR-5X3X) are provided with factory-installed damper linkages. Only base models (MPR-5X1X) require separately-ordered linkages.

These actuators are obsolete. They are listed here for reference only.

Table-3 Restrictions on Maximum Ambient Temperature for Valve Actuators.

Maximum Temperature of Media

in the Valve Body

(Check Rating of the Valve)

F ( C)

366 (186)

340 (171) 93 (34)

281 (138) 103 (39)

181 (83) 120 (48)

80 (26) 140 (60)

Maximum ambient temperature of the actuator must never exceed 140 F (60 C).

Minimum allowable ambient temperature of he actuators is -20 F (-29 C).

Maximum Ambient Temperature

of MPR-563X and -573X Serie

AV-600 (Only)

F ( C)

Do Not Use

AV-600 and AV-601

F ( C)

88 (31)

140 (60)

ACCESSORIES

Notes:

1. The 135 Ω controller is supplied by others.

2. The controller has setpoint and throttling range (proportional band) adjustments.

Black

24Vac Black/Blue

120Vac White

240Vac White/Black

To AC Power

Source

MPR-571X or MPR-573X

R B

Temp.

Drop

Controller

135 Ω Slidewire

Yellow/White

Red

Blue

Sequence of operation: As the temperature decreases at the controller, R moves toward B and the actuator shaft extends. On power loss to the actuator, the shaft retracts.

Green

Notes:

1. The 135 Ω controller is supplied by others.

2. The controller has setpoint and throttling range (proportional band) adjustments.

24Vac Black/Blue

120Vac White

240Vac White/Black

To AC Power

Source

R B

Temp.

Drop

Controller

135 Ω Slidewire

Blue

Red

Yellow/White

Black

MPR-571X or MPR-573X

Sequence of operation: As the temperature decreases at the controller, R moves toward B and the actuator shaft retracts. On power loss to the actuator, the shaft retracts.

Green

Common

11-1612 1/2" conduit bushing

Damper Linkages

AM-111 Crank arm for 5/16" diameter damper shaft AM-112 Crank arm for 3/8" diameter damper shaft AM-113 Crank arm for 1/2" diameter damper shaft AM-115 Crank arm for 7/16" diameter damper shaft AM-122 Linkage connector straight type AM-123 Damper clip AM-125 5/16" diameter x 20" damper rod AM-125-048 5/16" diameter x 48" damper rod AM-132 Ball joint connector AM-161-3 Damper linkage kit AM-601 Device includes mounting bracket, da

AM-602 Spacer

Valve Linkages and Valves

AV-600 Valve linkage 1/2" to 1-1/4" (obsolete VB-9XXX) AV-601 Valve linkage extension for hot water

AV-7600 Valves linkage 1/2" to 2" to be used with VB-7XXX VB-7XXX 1/2" to 2" valve bodies VB-9XXX 1/2" to 1-1/4" valve bodies (obsolete)

(factory-available)

TOOLS

TOOL-19 Spring compression tool for AV-600 TOOL-37 1-5/8" open-ended wrench TOOL-209 135 Ω and 0 to 7 mA manual positioner

straight connector. Requir (51 mm) stroke damper actuators.

AV-7600

ed to modify (MPR-5X1X series) valve actuators into 2"

mper linkage with spring, and AM-122

and steam applications; use with AV-

600 &

TYPICAL APPLICATIONS (wiring diagrams)

Figure-1 Wiring Diagram - Decrease in Temperature Causes Actuator Shaft to Extend.

+ 11 hidden pages