Sanyo DVW7100 User Manual [es]

			DVW-7100
INSTRUCTION MANUAL

DVD VIDEO PLAYER & 4-HEAD VCR

English

REPRODUCTOR DE DVD VIDEO Y VCR DE

Español

4 CABEZALES

Only cassettes marked can be used with this DVD+VCR.

As an ENERGY STAR® Partner, SANYO has determined that this product or product model meets the ENERGY STAR® guidelines for energy efficiency.

SANYO'S HELP-LINE

Call the toll-free number below if you have any difficulties operating this product. 1-800-813-3435 (Weekdays: 7:30 AM - 4:00 PM Central Time)

Please read this manual carefully before connecting your DVD+VCR and operating it for the first time.

Keep the manual in a safe place for future reference.

P/N: (8)3834RV0003Q (1E05/04)

Safety Precautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

WARNING: Do not install this equipment in a confined space such as a book case or similar unit.

NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV system installer's attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

CAUTION:

This DVD+VCR employs a Laser System.

To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference should the unit require maintenance, contact an authorized service location.

Use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure.

To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.

CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the product and receiver.

Connect the product into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

OTES ON COPYRIGHTS:

It is forbidden by law to copy, broadcast, show, broadcast via cable, play in public, or rent copyrighted material without permission.

This product features the copy protection function developed by Macrovision. Copy protection signals are recorded on some discs. When recording and playing the pictures of these discs on a VCR, picture noise will appear.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

SERIAL NUMBER: The serial number is found on the back of this unit. This number is unique to this unit and not available to others. You should record requested information here and retain this guide as a permanent record of your purchase.

Model No. ____________DVW-7100_____________

Serial No. __________________________________

2

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL. AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing.

This product does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

INTRODUCTION

1.Read these instructions. - All these safety and operating instructions should be read before the product is operated.

2.Keep these instructions. - The safety, operating and use instructions should be retained for future reference.

3.Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.

4.Follow all instructions. - All operating and use instructions should be followed.

5.Do not use this apparatus near water. – For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement; or near a swimming pool; and like.

6.Clean only with dry cloth. – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. -

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

3

Table of Contents

Introduction

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . 3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 6 About Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Display Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Preparation

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13

Connecting an Antenna/Cable TV to DVD+VCR . 11

Basic TV Connections . . . . . . . . . . . . . . . . . . . . 12

Optional, Preferred TV Connections . . . . . . . 12-13

Before Operation - VCR Part . . . . . . . . . . . . . . 14-16

On-Screen Display(OSD) . . . . . . . . . . . . . . . . . . 14

Setting the On-Screen Display . . . . . . . . . . . . . . 14

Setting the VCR Setup Menu . . . . . . . . . . . . . . . 15

Channel Selection . . . . . . . . . . . . . . . . . . . . . . . 15

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . 16

Before Operation - DVD Part . . . . . . . . . . . . . . 17-20

General Explanation. . . . . . . . . . . . . . . . . . . . . . 17

On-Screen Display. . . . . . . . . . . . . . . . . . . . . . . 17

Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . 18-20

Initial Settings General Operation . . . . . . . . . 18

LANGUAGE. . . . . . . . . . . . . . . . . . . . . . . . . 18

DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

LOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Operation

Operation with tape . . . . . . . . . . . . . . . . . . . . . 21-25

Normal Playback . . . . . . . . . . . . . . . . . . . . . . . . 21 Special Effect Playbacks . . . . . . . . . . . . . . . . . . 21

Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Still Picture and Frame-by-Frame Playback . 21 Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . 21 Ad JUMP (Advertisement Jump). . . . . . . . . . 21

Normal Recording . . . . . . . . . . . . . . . . . . . . . . . 22 Timer Recording . . . . . . . . . . . . . . . . . . . . . . 22-23 Instant Timer Recording . . . . . . . . . . . . . . . . . . . 24 Dubbing and Editing. . . . . . . . . . . . . . . . . . . . . . 24 Copying from DVD to VCR. . . . . . . . . . . . . . . . . 24 Tape Counter Memory Feature. . . . . . . . . . . . . . 25 Additional Information . . . . . . . . . . . . . . . . . . . . 25

Operation with DVD . . . . . . . . . . . . . . . . . . . . . 26-28

Playing DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Playback Setup . . . . . . . . . . . . . . . . . . . . . . 26 General Features . . . . . . . . . . . . . . . . . . . . . 26-27

Moving to another TITLE . . . . . . . . . . . . . . . 26 Moving to another CHAPTER. . . . . . . . . . . . 26 Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . 26 Still Picture and Frame-by-Frame Playback . 26 Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Repeat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 27 3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 27 Time Search . . . . . . . . . . . . . . . . . . . . . . . . 27 Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Marker Search . . . . . . . . . . . . . . . . . . . . . . . 27 Screen Saver. . . . . . . . . . . . . . . . . . . . . . . . 27

Special DVD Features . . . . . . . . . . . . . . . . . . . . 28 Checking the contents of DVD Video discs: Menus . 28 Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Camera Angle . . . . . . . . . . . . . . . . . . . . . . . 28 Changing the Audio Language . . . . . . . . . . . 28 Subtitle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Operation with Audio CD and MP3 Discs . . . . 29-30

Playing an Audio CD and MP3 Discs . . . . . . . . . 29 Notes on MP3 Recordings . . . . . . . . . . . . . . . . . 29 Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Moving to another Track . . . . . . . . . . . . . . . 30 Repeat Track/ All/ Off. . . . . . . . . . . . . . . . . . 30 Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Random . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 30

Programmed Playback . . . . . . . . . . . . . . . . . . . . . 31

Programmed Playback with Audio CD

and MP3 Discs . . . . . . . . . . . . . . . . . . . . . . . . . 31 Repeat Programmed Tracks . . . . . . . . . . . . 31 Erasing a Track from Program List . . . . . . . . 31 Erasing the Complete Program List . . . . . . . 31

Reference

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 32-34

Video Head Cleaning . . . . . . . . . . . . . . . . . . . . . 34

Language Code List . . . . . . . . . . . . . . . . . . . . . . . 35

Country Code List . . . . . . . . . . . . . . . . . . . . . . . . . 36

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

About the symbols for instructions

Indicates hazards likely to cause harm to the unit itself or other material damage.

Indicates special operating features of this unit. Indicates tips and hints for making the task easier.

4

1 ALL

Before Use

Playable Discs

DVD

3 inch/5 inch (8 cm/12 cm) disc

Audio CD

3 inch/5 inch (8 cm/12 cm) disc

In addition, this unit can play a CD-R or CD-RW that contains audio titles or MP3 files.

otes

Depending on the conditions of the recording equipment or the CD-R/RW disc itself, some CD-R/RW discs cannot be played on the unit.

The unit cannot play discs that contain data other than MP3 and CD-DA data.

Do not attach any seal or label to either side (the labeled side or the recorded side) of a disc.

Do not use irregularly shaped CDs (e.g., heartshaped or octagonal). It may result in malfunctions.

otes on DVDs

Some playback operations of DVDs may be intentionally fixed by software manufacturers. As this unit plays DVDs according to disc content designed by the software manufacturer, some playback features of the unit may not be available or other functions may be added. Refer also to the instructions supplied with the DVDs. Some DVDs made for business purposes may not be played on the unit.

Regional code of the DVD+VCR and DVDs

This DVD+VCR is designed and manufactured for playback of region

1 encoded DVD software. The region code on the labels of some

DVD discs indicates which type of DVD+VCR can play those discs. This unit can play only DVD discs labeled 1 or ALL. If you try to play any other discs, the message “Check Regional Code” will appear on the TV screen. Some DVD discs may not have a region code label even though their playback is prohibited by area limits.

ote on DTS-encoded CDs

When playing DTS-encoded CDs, excessive noise may be exhibited from the analog stereo output. To avoid possible damage to the audio system, turn down the volume before playing back such discs, adjust the volume gradually, and keep the volume level low. To enjoy DTS Digital SurroundTM playback, an external 5.1 channel Digital SurroundTM decoder system must be connected to the digital output of the unit.

	Disc-related terms						INTRODUCTION
	Title (DVD only)
	The main film content or accompanying feature content
	or music album.
	Each title is assigned a title reference number enabling
	you to locate it easily.
	Chapter (DVD only)
	Sections of a picture or a musical piece that are smaller
	than titles. A title is composed of one or several chap-
	ters. Each chapter is assigned a chapter number to
	enable you to locate the chapter you want. Depending
	on the disc, chapters may not be recorded.
	Track (audio CD only)
	Sections of a musical piece on an audio CD. Each track
	is assigned a track number, enabling you to locate the
	track you want.
	Remote control battery installation
		Detach the battery cover on the rear of the
	AAA AAA	remote control, and insert two AAA batter-
		ies with the		and		ends aligned correct-

ly.

Caution

Do not mix old and new batteries. Never mix different types of batteries (standard, alkaline, etc.).

Remote Control Operation Range

Point the remote control at the remote sensor and press the buttons.

Distance: About 23 ft (7 m) from the front of the remote sensor

Angle: About 30° in each direction of the front from the remote sensor

IMPORTANT NOTE:

SPENT OR DISCHARGED BATTERIES MUST BE RECYCLED OR DISPOSED OF IN A SAFE MANNER IN COMPLIANCE WITH ALL APPLICABLE LAWS. FOR DETAILED INFORMATION, CONTACT YOUR LOCAL COUNTY SOLID WASTE AUTHORITY.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.

DTS and DTS Digital Out are trademarks of Digital Theater

Systems, Inc.

5

Before Use (Continued)

Precautions

Handling the unit

When shipping the unit

The original shipping carton and packing materials come in handy. For maximum protection, re-pack the unit as it was originally packaged at the factory.

When setting up the unit

The picture and sound of a nearby TV, VCR, or radio may be distorted during playback. In this case, position the unit away from the TV, VCR, or radio, or turn off the unit after removing the disc.

To keep the surface clean

Do not use volatile liquids, such as insecticide spray, near the unit. Do not leave rubber or plastic products in contact with the unit for a long period of time. They will leave marks on the surface.

Cleaning the unit

To clean the cabinet

Use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit.

To obtain a clear picture

The DVD+VCR is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality will be poor.

Regular inspection and maintenance are recommended after every 1,000 hours of use. (This depends on the operating environment.)

For details, please contact your nearest dealer.

Notes on Discs

Handling discs

Do not touch the playback side of the disc.

Hold the disc by the edges so that fingerprints will not get on the surface.

Do not stick paper or tape on the disc.

Storing discs

After playing, store the disc in its case.

Do not expose the disc to direct sunlight or sources of heat, or leave it in a parked car exposed to direct sunlight, as there may be a considerable heat build-up inside the car.

Cleaning discs

Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the center out.

Yes No

Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records.

About Symbols

About the symbol display

“ ” may appear on the TV screen during operation. This icon means the function explained in this owner’s manual is not available on that specific DVD video disc.

About the disc symbols for instructions

A section whose title has one of the following symbols are applicable only to those discs represented by the symbol.

DVD DVDs Audio CD

Setting the Output Source

You must select one of your output sources (DVD or VCR) to view on the TV screen.

•If you want to view output source of DVD deck:

Press DVD on the remote control or DVD/VCR on the front panel until DVD indicator in the display window lights and output source of DVD deck is viewed on the TV screen.

•If you want to view output source of VCR deck:

Press VCR on the remote control or DVD/VCR on the front panel until VCR indicator in the display window lights and output source of VCR deck is viewed on the TV screen.

ote

•If you insert a disc while the DVD+VCR is in the VCR mode, the DVD+VCR will switch to DVD mode automatically.

•If you insert a cassette tape without an erasure prevention tab intact while the DVD+VCR is in the DVD mode, the DVD+VCR will switch to VCR mode automatically.

6

Front Panel

POWER

Switches the DVD+VCR ON and OFF.

DVD/VCR SELECT (output select)

Select one of your output sources to view on the TV screen between DVD and VCR.

Disc Tray (DVD deck)

Insert a disc here.

AV INPUT (VIDEO IN/AUDIO IN)

Connect the audio/video output of an external source (Audio system, TV/Monitor, Another VCR).

Cassette Compartment (VCR deck)

Insert a video cassette here.

PLAY (B)				Remote Sensor
Starts playback of a disc or tape.
				Point the DVD+VCR
Display window				remote control here.
Shows the current status of the
DVD+VCR.

INTRODUCTION

VCR indicator

Indicates the active VCR

EJECT(Z)

deck.

Ejects the tape in the

DVD indicator

VCR deck.

Indicates the active DVD deck.

OPEN/CLOSE (Z)

Opens or closes the disc tray.

REC (z)

PAUSE/STILL(X)

To record normally or to acti-

vate Instant Timer

Pause playback temporarily/press

Recording.

repeatedly for Frame-by-Frame play-

back.

CHANNEL (V/v)

STOP (x)

To scan up or down through mem-

orized channels.

Stops playback of the disc or tape.

FF(M)

Child Lock

DVD: Go to NEXT chapter/track. Press

and hold for a fast forward search.

The control buttons on the front panel of the

VCR: Advances the tape from STOP

DVD+VCR can be switched off so that your

mode or for fast forward picture

DVD+VCR can only be operated using the

search.

remote control.

Press SAFE on the remote control to enable

REW (m)

LOCK function, SAFE and

appear in the

DVD: Go to beginning of current

display window.

chapter/track or to previous chapter/track.

To disable the LOCK function, press SAFE on

Press and hold for a fast reverse search.

the remote control until OFF appears in the

VCR: Rewinds the tape from STOP mode or

display window.

for fast reverse picture search.

7

Display Window

The DVD deck is selected.

A disc is in the DVD deck.

(Lights when a disc is in the DVD deck and Flashes when no disc.)

Indicates when the Progressive scan is active.

Indicates repeat mode.

Indicates when the DVD+VCR is locked.

DVD+VCR is in timer recording or a timer recording is programmed.(VCR part only)

A cassette is in the VCR deck.

The VCR deck is selected.

DVD

[P]

VCR

REC

PM

TV

Lights when TV mode is active (See page 22.)

Indicates PM time. (AM is not displayed.)

DVD+VCR is Recording. (VCR part only)

Indicates total playing time, elapsed time, remaining time or current deck status (Playback, Pause, etc).

8

Remote Control

DVD/VCR select button

Selects the output source (DVD or VCR) to view on the TV screen.

POWER

Switches DVD+VCR ON and OFF.

TV/VCR

To view channels selected by the VCR tuner or by the TV tuner.

DISPLAY, CLK/CNT

Accesses On-Screen display.

Switches among the clock, tape counter and tape remaining modes on the display.

b/B/v/V (left/right/up/down)

-Selects an option in the menu

-CH/TRK (v/V): Selects channel of VCR.

Adjusts manually the tape’s picture

onscreen.

SETUP, MENU

Accesses or removes DVD setup menu and VCR menu.

TITLE

Displays the disc’s Title menu, if available.

PAUSE/STEP (X)

Pauses playback or recording.

Presses repeatedly for frame-by-frame playback.

STOP (x)

Stops playback.

REC (z)

Records normally or activates Instant Timer Recording.

0-9 number buttons

Selects numbered options in a menu.

AUDIO

Selects an audio language (DVD).

SUBTITLE

Selects a subtitle language.

MARKER

Marks any point during playback.

SEARCH

Displays MARKER SEARCH menu.

REPEAT

Repeat chapter, track, title, all.

RANDOM, Ad JUMP

-Plays tracks in random order.

-Fast forwards picture search through

30 seconds of recording.

A-B, SP/SLP

-Repeats in sequence.

-Selects recording speed

OPEN/CLOSE, EJECT (Z)

- Opens and closes the disc tray.

- Ejects the tape in the VCR deck.

SELECT/ENTER ( )

- Acknowledges menu selection.

- Displays functions on the TV screen.

This button is not available.

DISC MENU

Shows DVD disc menu.

INPUT

To select the VCR deck’s source (Tuner,

LINE 1, or LINE 2).

FORWARD (>)

DVD; Search forward*/go to next chapter or track.

VCR; Advances the tape during the STOP mode or for fast forward picture search.

PLAY (H)

Starts playback.

BACKWARD (.)

DVD; Search backward*/go to beginning of current chapter or track or go to previous chapter or track.

VCR; Rewinds the tape during the STOP mode or for fast reverse picture search.

* Press and hold button for about two seconds.

PROGRAM

Shows or hides Program menu.

CLEAR

Clears a track number from the program menu or a mark on the

MARKER SEARCH menu.

SAFE

Switch the Lock function on and off.

ANGLE

Selects a DVD camera angle if available.

RETURN (O)

Removes the setup menu.

ZOOM

Enlarges DVD video image.

ote

This remote control uses the same buttons for VCR and DVD functions (ex. PLAY).

When using a VCR, first press the VCR button. When using a DVD, first press the DVD button.

INTRODUCTION

9

Rear Panel

VCR IN LINE 1 (VIDEO IN/AUDIO IN)

Connect the audio/video output of an external source (Audio system,

TV/Monitor, Another VCR).

DVD/VCR OUT (VIDEO/AUDIO (Left/Right))

Connect to a TV with video and audio inputs.

COMPONENT/PROGRESSIVE SCAN VIDEO OUT (Y Pb Pr) (DVD OUT)

Connect to a TV with Y Pb Pr inputs.

AUDIO OUT (Left/Right) (DVD OUT)

Connect to a TV, amplifier, receiver, or stereo system.

AC Power Cord

Plug into the power source (AC 120V, 60 Hz).

S-VIDEO OUT (DVD OUT)

Connect to a S-Video Input on TV.

DIGITAL AUDIO OUT (COAXIAL) (DVD OUT)

Connect to digital (coaxial) audio equipment.

ANT.IN (ANTENNA INPUT)

Connect the VHF/UHF/CATV antenna to this terminal.

RF. OUT(DVD/VCR OUT)

Connect to a TV with RF coaxial inputs.

Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit.

10

Connections

ips

Depending on your TV and other equipment you wish to connect, there are various ways you could connect the

DVD+VCR. Use connections described on pages 11-13.

Please refer to the manuals of your TV, VCR, Stereo

System or other devices as necessary to make the best connections.

For better sound reproduction, connect the DVD+VCR’s DVD/VCR AUDIO OUT jacks to the audio in jacks of your amplifier, receiver, stereo or audio/video equipment. See

Optional, Preferred TV Connections on pages 12-13.

Caution

Make sure the DVD+VCR is connected directly to the TV.

Tune the TV to the correct video input channel.

Do not connect the DVD+VCR’s DVD/VCR AUDIO OUT jacks to the phono in jack (record deck) of your audio system.

Do not connect your DVD+VCR via your VCR. The DVD image could be distorted by the copy protection system.

Connecting an Antenna/Cable TV to DVD+VCR

1	Disconnect the antenna leads from the rear of the
	TV.

2 Identify the type of cable from your antenna. If it is a round cable as illustrated, it is a 75 ohm coaxial antenna cable. This cable will connect directly to the jack marked ANT.IN on your DVD+VCR.

ip

If your antenna lead wire is a flat type antenna cable, connect it to a Antenna Adaptor (300-ohm to 75-ohm) (not supplied) and slip the Adaptor onto the ANT.IN jack. The Adaptor does not screw on to the DVD+VCR, it just slips over the jack.

Antenna Antenna

Cable TV

Wall Jack

Flat Wire
(300 ohm)
300/75 ohm	OR	OR
Adaptor
(Not supplied)

Rear of DVD+VCR

Without Cable Box

If your cable wire is connected to your TV without a converter or descrambler box, unscrew the wire from your TV and attach it to the ANT.IN jack on the DVD+VCR. Use the supplied round coaxial cable to connect between the DVD+VCR’s RF.OUT jack and the 75 ohm antenna input jack on the TV. With this connection, you can receive all midband, super band, and hyperband channels.

With Cable Box

If a converter is required in your cable system, follow the instructions below:

The cable hookup permits both TV and DVD+VCR operation.

To view or record CATV channel

1Tune the TV to the DVD+VCR output channel (CH 3 or 4).

2Set the DVD+VCR channel selector to the output channel of the Cable Converter box by pressing the CH/TRK (v/V) or number (0-9) of your DVD+VCR. (Example: CH3)

3Select the channel to view at the Cable Converter Box.

otes

With this connection, you CANNOT record one program while viewing another.

If you are using a cable box to tune channels, it is not necessary to do Auto Channel Programming as indicated on page 15.

Cable TV

Wall Jack

Back Panel of

Typical Cable Box

Rear of DVD+VCR

PREPARATION

11

Connections (Continued)

Basic TV Connections

Make one of the following connections, depending on the capabilities of the equipment to be connected.

RF coaxial connection

Connect the RF.OUT jack on the DVD+VCR to the antenna in jack on the TV using the 75-ohm Coaxial Cable supplied (R).

ote

If you use this connection, tune the TV to the DVD+VCR’s RF output channel (CH 3 or 4).

How to set the DVD+VCR’s RF output channel

1.Set the TV to the VCR channel (3 or 4) depending upon the selected channel.

2.When the DVD+VCR is turned off, press and hold CHANNEL (V/v) on the front panel for more than five seconds.

It will turn itself on and “RF03” or “RF04” appears in the display window.

3.Press CHANNEL (V/v) on the front panel or CH/TRK (v/V) on the remote control to change the RF output channel (CH 03 or CH 04).

4.Turn off the DVD+VCR.

Audio/Video connection

1	Connect the DVD/VCR VIDEO OUT jack on the
	DVD+VCR to the video in jack on the TV using the

supplied video cable (V).

2 Connect the Left and Right DVD/VCR AUDIO OUT jacks on the DVD+VCR to the audio left/right in jacks on the TV (A1) using the supplied audio cables.

ote

If you use this connection, set the TV’s source selector to VIDEO.

Rear of TV

	ANTENNA	AUDIO INPUT		VIDEO
	INPUT			INPUT
		L	R

R A1 V

Rear of DVD+VCR

Optional, Preferred TV Connections

ote

You can ONLY watch and listen to DVD playback through the connections shown below.

S-Video connection

1	Connect the S-VIDEO OUT jack on the DVD+VCR
	to the S-Video in jack on the TV using the optional

S-Video cable (S).

2 Connect the Left and Right AUDIO OUT jacks of the DVD+VCR to the audio left/right in jacks on the TV using the supplied audio cables (A2).

Component Video (Color Stream®) / Progressive Scan (ColorStream® pro) connection

If your television is a high-definition or “digital ready” television, you may take advantage of the DVD+VCR’s progressive scan output for the highest video resolution possible.

If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try Progressive Scan on the DVD+VCR.

1 Connect the COMPONENT / PROGRESSIVE SCAN VIDEO OUT jacks on the DVD+VCR to the corresponding in jacks on the TV using an optional Y Pb Pr cable (C).

2 Connect the Left and Right AUDIO OUT jacks of the DVD+VCR to the audio left/right in jacks on the TV (A2) using the supplied audio cables.

otes

Set the Progressive Scan to “On” on the setup menu for progressive scan signal, see page 18.

When you use Component Video signal, set the Progressive Scan to “Off” on the setup menu. Progressive scan does not work with the analog video connections (yellow VIDEO OUT jack).

Rear of TV

	COMPONENT VIDEO INPUT			AUDIO INPUT		S-VIDEO
						INPUT
	Pr	Pb	Y	R	L

C

A2 S

Rear of DVD+VCR

12