Contact SAMSUNG WORLD-WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Kapcsolatfelvétel: SAMSUNG WORLD-WIDE
Bármilyen észrevétele, vagy kérdése van Samsung termékekkel kapcsolatban, forduljon a
SAMSUNG ügyfélszolgálathoz.
Kontakt do SAMSUNG WORLD-WIDE
Jeżeli masz jakieś uwagi lub pytania w sprawie produktów marki Samsung, skontaktuj się z naszą infolinią.
Επικοινωνήστε με τη SAMSUNG ΣΕ ΟΛΟ ΤΟΝ ΚΟΣΜΟ
Εάν έχετε σχόλια ή ερωτήσεις σχετικά με προϊόντα της Samsung, επικοινωνήστε με το κέντρο εξυπηρέτησης πελατών της SAMSUNG.
Свържете се със SAMSUNG ПО ЦЕЛИЯ СВЯТ
Ако имате въпроси или коментар и за продуктите на Samsung, се обърнете към центъра за обслужване на клиенти на SAMSUNG.
Skontaktujte Celosvetový Samsung
Ak máte nejaké otázky alebo komentáre ohľadom produktov spoločnosti Samsung, prosím, skontaktujte centrum starostlivosti o zákazníkov spoločnosti SAMSUNG.
Kontaktirajte SAMSUNG ŠIROM SVIJETA
Ako imate pitanja ili komentara u vezi s proizvodima tvrtke Samsung, obratite se centru za brigu o kupcima tvrtke Samsung.
Kontaktujte Samsung po celém světě
Pokud máte dotazy nebo připomínky týkající se výrobků Samsung, kontaktujte středisko péče o zákazníky společnosti SAMSUNG.
Contactaţi SAMSUNG WORLD WIDE (Samsung în întreaga lume)
Dacă aveţi întrebări sau comentarii în legătură cu produsele Samsung, contactaţi centrul de asistenţă pentru clienţi SAMSUNG.
Dünyanın her yerinden SAMSUNG’a ulaşın.
Samsung ürünleri ile ilgili sorularınız ya da yorumlarınız varsa lütfen SAMSUNG müşteri hizmetleri merkezi ile temasa geçin.
Country |
Customer Care Centre |
Web Site |
BELGIUM |
02 201 2418 |
www.samsung.com/be |
CZECH REPUBLIC |
844 000 844 |
www.samsung.com/cz |
|
“Distributor pro Českou republiku: |
|
|
Samsung Zrt., česka organizační složka Vyskočilova 4, 14000 Praha 4” |
|
DENMARK |
70 70 19 70 |
www.samsung.com/dk |
FINLAND |
030-6227 515 |
www.samsung.com/fi |
FRANCE |
3260 SAMSUNG(7267864) (€ 0,15/min) |
www.samsung.com/fr |
GERMANY |
01805-121213 (€ 0,14/Min) |
www.samsung.de |
HUNGARY |
06-80-SAMSUNG (7267864) |
www.samsung.com/hu |
ITALIA |
800 SAMSUNG(7267864) |
www.samsung.com/it |
LUXEMBURG |
0032 (0)2 201 24 18 |
www.samsung.lu |
NETHERLANDS |
0900 20 200 88 (€ 0,10/Min) |
www.samsung.com/nl |
NORWAY |
815-56 480 |
www.samsung.com/no |
POLAND |
0 801 801 881 |
www.samsung.com/pl |
PORTUGAL |
80 8 200 128 |
www.samsung.com/pt |
REPUBLIC OF IRELAND |
0818 717 100 |
www.samsung.com/uk |
SLOVAKIA |
0800-SAMSUNG (7267864) |
www.samsung.com/sk |
SPAIN |
902 10 11 30 |
www.samsung.com/es |
SWEDEN |
0771-400 200 |
www.samsung.com/se |
SWITZERIAND |
0800-7267864 |
www.samsung.com/ch |
U.K |
0870 SAMSUNG (7267864) |
www.samsung.com/uk |
ESTONIA |
800-7267 |
www.samsung.ee |
LATVIA |
800-7267 |
www.samsung.com/lv |
LITHUANIA |
8-800-77777 |
www.samsung.lt |
KAZAKHSTAN |
8 800 080 1188 |
www.samsung.kz |
RUSSIA |
8-800-200-0400 |
www.samsung.ru |
UKRAINE |
8-800-502-0000 |
www.samsung.com/ur |
UZBEKISTAN |
140-1234 |
www.samsung.uz |
LCD TV
LE32S6
LE37S6
LE40S6
Owner’s Instructions
Before operating the unit, please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
PC DISPLAY
PICTURE IN PICTURE (PIP)
TELETEXT
Register your product at www.samsung.com/global/register Record your Model and Serial number here for future reference.
▪ Model _______________ ▪ Serial No. _______________
BN68-01234B-00
Precautions When Displaying a Still Image
A still image may cause permanent damage to the TV screen.
•Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention. This image retention is also known as "screen burn".
To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.
•Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and center of
the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause a similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.
•Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
©2007 Samsung Electronics Co., Ltd. All rights reserved.
Contents |
|
Connecting and Preparing Your TV |
|
List of Parts.............................................................. |
2 |
Installing the Stand................................................... |
2 |
Installing the Wall Mount Kit.................................. |
2 |
Viewing the Control Panel........................................ |
3 |
Viewing the Connection Panel................................. |
4 |
Viewing the Remote Control..................................... |
6 |
Installing Batteries in the Remote Control................ |
6 |
Switching On and Off............................................... |
7 |
Placing Your Television in Standby Mode................ |
7 |
Plug & Play............................................................... |
7 |
Setting the Channels |
|
Storing Channels Automatically................................ |
8 |
Storing Channels Manually...................................... |
8 |
Setting the Channel Manager................................... |
9 |
Activating the Child Lock....................................... |
10 |
Sorting the Stored Channels.................................... |
10 |
Assigning Channels Names..................................... |
11 |
Fine Tuning Channel Reception............................... |
11 |
Setting the Picture |
|
Changing the Picture Standard................................ |
12 |
Adjusting the Custom Picture................................... |
12 |
Changing the Colour Tone........................................ |
12 |
Resetting the Picture Settings to the |
|
Factory Defaults....................................................... |
13 |
Changing the Picture Size........................................ |
13 |
Freezing the Current Picture.................................... |
13 |
Digital Noise Reduction............................................ |
13 |
DNIe Demo (Digital Natural Image engine).............. |
14 |
Viewing the Picture In Picture (PIP)......................... |
14 |
Setting the Sound |
|
Changing the Sound Standard.............................. |
15 |
Adjusting the Sound Settings................................ |
15 |
Setting the TruSurround XT (SRS TSXT)............. |
16 |
Adjusting the Volume Automatically...................... |
16 |
Selecting the Internal Mute................................... |
16 |
Listening to the Sound of the Sub Picture............ |
17 |
Resetting the Sound Settings to the |
|
Factory Defaults.................................................... |
17 |
Connecting Headphones....................................... |
17 |
Setting the Time |
|
Setting and Displaying the Current Time.............. |
17 |
Setting the Sleep Timer......................................... |
18 |
Switching the Television |
|
On and Off Automatically...................................... |
18 |
Setting the Others |
|
Choosing Your Language...................................... |
19 |
Using Game Mode................................................ |
19 |
Setting the Blue Screen Mode / |
|
Selecting the Melody ............................................ |
19 |
Using the Energy Saving Feature......................... |
20 |
Selecting the Source............................................. |
20 |
Editing the Input Source Names........................... |
20 |
Using the Teletext Feature |
|
Teletext Decoder................................................... |
21 |
Displaying the Teletext Information....................... |
21 |
Selecting a Specific Teletext Page........................ |
22 |
Using Fastext to Select a Teletext Page............... |
22 |
Setting the PC |
|
Setting up Your PC Software |
|
(Based on Windows XP)....................................... |
23 |
Display Modes....................................................... |
23 |
Setting the PC....................................................... |
24 |
Recommendations For Use |
|
Using the Anti-Theft Kensington Lock................... |
25 |
Troubleshooting: |
|
Before Contacting Service Personnel................... |
25 |
Technical and Environmental Specifications ........ |
26 |
Symbol |
Press |
Important |
Note |
One-Touch |
|
|
|
|
Button |
|
|
|
|
English- |
English
Please make sure the following items are included with your LCD TV.
If any items are missing, contact your dealer.
|
|
|
|
M4 X L16 |
|
|
|
|
Remote Control & |
Power Cord |
Cover-Bottom |
Stand Screw X4 |
Stand |
Cleaning Cloth |
|||
Batteries (AAA x 2) |
||||||||
|
|
|
|
|
|
|
||
Owner’s Instructions |
Warranty card |
Service Network Card |
Safety Guide |
Registration Cards |
Warranty card / Service Network Card / Safety Guide / Registration Cards (Not available in all locations) The stand and stand screw may not be included depending on the model.
< 2 > |
< 3 > |
1.Place the TV faced down on a soft cloth or cushion on a table.
2.Put the stand into the hole at the bottom of the TV.
3.Insert screw into the hole indicated and tighten.
The stand is installed for models with the screen size of 40 inch and above.
Wall mount items (sold separately) allow you to mount the TV on the wall.
For detailed information on installing the wall mount, see the instructions provided with the Wall Mount items. Contact a technician for assistance when installing the wall mounted bracket.
Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the TV on your own.
Remove the stand and cover the bottom hole with a cap and fasten with two screws.
English-
The product colour and shape may vary depending on the model.
SOURCE
Toggles between all the available input sources (TV, Ext.1, Ext.2, AV, S-Video, Component, PC, HDMI). In the on-screen menu, use this button as you use the ENTER button on the remote control.
MENU
Press to see an on-screen menu of your TV’s features.
Press to decrease or increase the volume.
In the on-screen menu, use the buttons as you use the and buttons on the remote control.
Press to change channels.
In the on-screen menu, use the buttons as you use the and buttons on the remote control. (Without the Remote Control, you can turn on the TV by using the Channel buttons.)
Speakers
Remote Control Sensor
Aim the remote control towards this spot on the TV.
(Power)
Press to turn the TV on and off.
Power Indicator
Blinks and turns off when the power is on and lights up in stand-by mode.
English-
Power Input |
Whenever you connect an external device to your TV, make sure that power on the unit is turned off. When connecting an external device, match the colour of the connection terminal to the cable.
English-
Connecting an Aerial or Cable Television Network
To view television channels correctly, a signal must be received by the set from one of the following sources: - An outdoor aerial / A cable television network / A satellite network
Connecting HDMI/DVI
-Supports connections between HDMI-connection-enabled AV devices (Set-Top Boxes, DVD players, AV receivers and digital TVs).
-No additional Audio connection is needed for an HDMI to HDMI connection.
What is HDMI?
-“High Definition Multimedia interface” allows the transmission of high definition digital video data and multiple channels of digital audio ( 5.1 channels).
-The HDMI/DVI terminal supports DVI connection to an extended device with the appropriate cable (not supplied). The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP
(High Bandwidth Digital Copy Protection) coding feature installed, and supports multi - channel digital audio.
You should use the DVI-to-HDMI cable or DVI-HDMI Adapter for the connection, and the “R - AUDIO - L” terminal on DVI for sound output.
-When connecting this product via HDMI or DVI to a Set Top Box, DVD Player or Games Console etc, make sure that it has been set to a compatible video output mode as shown in the table below.
Failure to observe this may result in picture distortion, image breakup or no picture.
Supported modes for DVI or HDMI
|
480i |
480p |
576i |
576p |
720p |
1080i |
50Hz |
X |
O |
X |
O |
O |
O |
60Hz |
X |
O |
X |
X |
O |
O |
Component |
O |
O |
O |
O |
O |
O |
-Do not attempt to connect the HDMI/DVI connector to a PC or Laptop Graphics Card. (This will result in a blank screen being displayed)
Connecting Set-Top Box, VCR or DVD
-Connect the VCR or DVD SCART cable to the SCART connector of the VCR or DVD.
-If you wish to connect both the Set-Top Box and VCR (or DVD), you should connect the Set-Top Box to the VCR (or DVD) and connect the VCR (or DVD) to your set.
SERVICE
- Service connection for qualified service engineer.
Connecting AUDIO
-Connect RCA audio cables to “R - AUDIO - L” on the rear of your set and the other ends to corresponding audio in connectors on the Amplifier or DVD Home Theater.
Connecting Computer
-Connect the D- Sub cable (optional) to “PC (PC IN)” on the rear of your set and the other end to the Video Card of your computer.
-Connect the stereo audio cable (optional) to “AUDIO (PC IN)” on the rear of your set and the other end to “Audio Out” of the sound card on your computer.
Connecting External A/V Devices
-Connect RCA or S-VIDEO cable to an appropriate external A/V device such as VCR, DVD or Camcorder.
-Connect RCA audio cables to “R - AUDIO - L” on the rear of your set and the other ends to corresponding audio out connectors on the A/V device.
-Headphone may be connected to the headphone output ( ) on the rear of your set. While the headphone is connected, the sound from the built-in speakers will be disabled.
Connecting Component Devices (DTV/DVD)
-Connect component video cables (optional) to component connector (“PR”, “PB”, “Y”) on the rear of your set and the other ends to corresponding component video out connectors on the DTV or DVD.
-If you wish to connect both the Set-Top Box and DTV (or DVD), you should connect the Set-Top Box to the DTV (or DVD) and connect the DTV (or DVD) to component connector (“PR”, “PB”, “Y”) on your set.
-The PR, PB and Y connectors on your component devices (DTV or DVD) are sometimes labeled Y, B-Y and R-Y or Y, Cb and Cr.
-Connect RCA audio cables (optional) to “R - AUDIO - L” on the rear of your set and the other ends to corresponding audio out connectors on the DTV or DVD.
-This LCD TV displays its optimum picture resolution in 720p mode.
-This LCD TV displays its maximum picture resolution in 1080i mode.
Kensington Lock
-The Kensington lock (optional) is a device used to physically fix the system when used in a public place.
-If you want to use a locking device, contact the dealer where you purchased the TV.
-The place of the Kensington Lock may be different depending on its model.
English-
Television Standby button
Number buttons for direct channel access
One/Two-digit channel selection
Selects the TV mode directly
It display “Channel Manager” on the screen.
Volume increase
Volume decrease
Temporary sound switch-off
Menu display and change confirmation
Sound mode selection
Picture-In-Picture On / Off
Picture effect selection
PIP FUNCTIONS
SOURCE: Input source selection SWAP: Interchange the main and
sub picture SIZE: PIP size selection
POSITION: PIP position selection P: Next channel
P: Previous channel Sound effect selection SRS TSXT selection
Available source selection Previous channel
Selects the PC mode directly
Automatic Power-off
P: Next channel
P: Previous channel Exit the OSD
Control the cursor in the menu
Use to see information on the current broadcast
Picture freeze
Picture size selection
Teletext Functions
Exit from the teletext display
Teletext index
Teletext hold
SOURCE: Teletext size selection
SWAP: Teletext store
Teletext mode selection (LIST/FLOF)
Teletext sub page
P: Teletext next page
P: Teletext previous page Teletext cancel
Teletext reveal
Alternately select Teletext, Double, or Mix.
Fastext topic selection
The performance of the remote control may be affected by bright light.
This is a special remote control for the visually impaired,
and has Braille points on the Power, Channel and Volume buttons.
1.Lift the cover at the back of the remote control upward as shown in the figure.
2. Install two AAA size batteries.
Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment.
3.Replace the cover.
Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time. The remote control can be used up to about 23 feet from the TV.
(Assuming typical TV usage, the batteries last for about one year.)
If the remote control doesn’t work, check the following:
1.Is the TV power on?
2.Are the plus and minus ends of the batteries reversed?
3.Are the batteries drained?
4.Is there a power outage, or is the power cord unplugged?
5.Is there a special fluorescent light or neon sign nearby?
English-
The mains lead is attached to the rear of your set.
1.Plug the mains lead into an appropriate socket.
The standby indicator lights up on the front of the set.
2.Press the button on the front of the set.
You also can press the POWER button or the TV () button on the remote control to turn the TV on.
The programme that you were watching last is reselected automatically.
3.Press the numeric button (0~9) or channel up/down (/) button on the remote control or
button on the right side of the set.
When you switch the set on for the very first time, you will be asked to choose language in which the menus are to be displayed.
4.To switch your set off, press the POWER button again.
Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).
1.Press the POWER button on the remote control.
The screen is turned off and a red standby indicator appears on the front of your set.
2.To switch your set back on, simply press the POWER , numeric buttons (0~9) or channel up/down (/) button again.
Do not leave your set in standby mode for long periods of time (when you are away on holiday, for example). It is best to unplug the set from the mains and aerial.
When the TV is initially powered on, several basic settings proceed automatically and subsequently. The following settings are available.
1. Press the POWER button on the remote control.
The message “Start Plug & Play” is displayed with “OK” selected.
2. Select the appropriate language by pressing the or button. Press the ENTER button to confirm your choice.
3.The message “Check antenna input.” is displayed with “OK” selected. Press the ENTER button.
Please check that the antenna cable is connected correctly.
4.Select the appropriate country by pressing the or button. Press the ENTER button to confirm your choice.
5.The “Auto Store” menu is displayed with the “Start” selected. Press the ENTER button.
The channel search will start and end automatically.
After all the available channels are stored, the “Clock Set” menu appears.
Press the ENTER button at any time to interrupt the memorization process.
6.Press the ENTER button.
Select the “Hour” or “Minute” by pressing the or button. Set the “Hour” or “Minute” by pressing the or button.
You can also set the hour and minute by pressing the number buttons on the remote control.
7.Press the ENTER button to confirm your setting.
Language: Select your language.
Country: Select your country.
Auto Store: Automatically scans for and stores channels available in the local area.
Clock Set: Sets the current time for the TV clock.
English-
If you want to reset this feature...
1. Press the MENU button to display the menu.
Press the or button to select “Setup”, then press the ENTER button. 2. Press the ENTER button again, to select “Plug & Play”.
3. The message to “Start Plug & Play” is displayed.
- Storing Channels Automatically |
- Storing Channels Manually |
You can scan for the frequency ranges available to you (and availability depends on your country). Automatically allocated programme numbers may not correspond to actual or desired programme numbers. However, you can sort numbers manually and clear any channels you do not wish to watch.
1.Press the MENU button to display the menu.
Press the or button to select “Channel”, then press the ENTER button.
2.Press the ENTER button to select “Country”.
3.Select the appropriate country by pressing the or button. Press the ENTER button to confirm your choice.
4.Press the or button to select “Auto Store”, then press the ENTER button.
5.Press the ENTER button.
The TV will begin memorizing all of the available channels.
Press the ENTER button at any time to interrupt the memorization process and return to the “Channel” menu.
6.After all the available channels are stored, the “Sort” menu appears.
You can store up to 100 channels, including those received via cable networks. When storing channels manually, you can choose:
Whether or not to store each of the channels found.
The programme number of each stored channel which you wish to identify.
1.Press the MENU button to display the menu.
Press the or button to select “Channel”, then press the ENTER button.
2.Press the or button to select “Manual Store”, then press the ENTER button.
3.Press the ENTER button to select “Programme”.
4.To assign a programme number to a channel, find the correct number by pressing the or button and then press the ENTER button.
You can also set a programme number by pressing number buttons on the remote control.
English-
5.Press the or button to select “Colour System”, then press the ENTER button.
6.Select the colour standard required by pressing the or button then, press the ENTER button.
7.Press the or button to select “Sound System”, then press the ENTER button.
8.Select the sound standard required by pressing the or button, then press the ENTER button.
If there is an abnormal sound or no sound, re-select the sound system required.
9.If you know the number of the channel to be stored, press the or button to select “Channel”. Press the ENTER button. Select C (Air channel) or S (Cable channel) by pressing the or button. Press the button to select channel. Select the required number by pressing the or button and then press the ENTER button.
Channel mode: P (Programme mode), C (Air channel mode), S (Cable channel mode)
You can also set a channel number by pressing number buttons on the remote control.
10.If you do not know the channel numbers, press the or button to select “Search”.
Press the ENTER button. Search by pressing the or button and then press the ENTER button.
11.Press the or button to select “Store”. Press the ENTER button to select “OK”.
12.Repeat steps 3 to 11 for each channel to be stored.
Programme: Selects a program number for the channel. |
Channel: Selects a channel. |
Colour System: Sets the colour supporting system. |
Search: Scans for the frequency value for the channel. |
Sound System: Sets the sound supporting system. |
Store: Saves your settings. |
|
|
Set the channels according to your preference.
You can easily delete, add, or lock the channel you want.
1.Press the MENU button to display the menu. to select “Channel”, then press the ENTER
Press the or button button.
2. Press the or button to select “Channel Manager”, then press the ENTER button.
3. Press the ENTER button again, to select “Channel Manager”. 4. Press the button to select “ ” line.
5. Press the or button to select the undesired channel, then press the ENTER button to cancel.
6. Repeat steps 5 for each channel to be selected or canceled 7. Press the EXIT button to exit.
“ ” is active when “Child Lock” is selected to “On”.
You can select these options by simply pressing the CH MGR button on the remote control.
English-
This feature allows you to prevent unauthorized users, such as children,
from watching unsuitable programmes by muting out video and audio.
Child Lock cannot be released using the buttons on the side.
Only the remote control can release the Child Lock setting, so keep the remote control away from children.
1. Press the MENU button to display the menu. Press the or button to select “Channel”, then press the ENTER button.
2.Press the or button to select “Channel Manager”,
then press the ENTER button.
3. Press the or button to select “Child Lock”,
|
|
|
|
|
|
|
|
4. |
then press the ENTER |
button. |
||
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
Press the or button to select “On”. Press the ENTER button. |
||||
|
|
|
|
|
|
|
|
5. Press the or button to select “Channel Manager”, |
||||
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
then press the ENTER |
button. |
||
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
Press the button to select “ |
|
” line. |
|
|
|
|
|
|
|
|
|
6. |
|
|||
|
|
|
|
|
|
|
|
7. |
Press the or button to select the channels you want to lock, |
|||
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
then press the ENTER |
button. |
||
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
8. |
Repeat steps 7 for each channel to be locked or unlocked. |
|||||
|
|
|
|
|
||||||||
9. |
Press the EXIT button to exit. |
Select “On” or “Off” in “Child Lock” to easily turn the channels which selected on “ ” to be active or inactive.
You can exchange the numbers of two channels, in order to:
Modify the numeric order in which the channels have been
automatically stored.
Give easily remembered numbers to the channels that you watch most often.
1.Press the MENU button to display the menu. to select “Channel”, then press the ENTER
Press the or button button.
2.Press the or button to select “Sort”, then press the ENTER button.
3.Select channel number that you wish to change by pressing theor button repeatedly. Press the ENTER button.
The selected channel number and name are moved to right side.
4.Press the or button to move to the position in which you would like to change and then press the ENTER button.
The selected channel is exchanged with the one previously stored to the chosen number.
5.Repeat steps 3 to 4 for another channel to be sorted.
6.Press the EXIT button to exit.
English-10
Channel names will be assigned automatically when channel
information is broadcast.
These names can be changed, allowing you to assign new names.
1.Press the MENU button to display the menu. to select “Channel”, then press the ENTER
Press the or button button.
2. Press the or button to select “Name”, then press the ENTER button.
3.If necessary, select the channel to be assigned to a new name by pressing the or button. Press the ENTER button.
The selection bar is displayed around the name box.
4. |
|
|
|
To... |
Then... |
|
|
|
Select a letter, number or symbol |
Press the or button |
|
|
Move on the next letter |
Press the button |
|
|
Move back the previous letter |
Press the button |
|
|
Confirm the name |
Press the ENTER |
button |
The characters available are :
Letters of the alphabet (A~Z) / Numbers (0~9) / Special characters ( -, space)
5.Repeat steps 3 to 4 for each channel to be assigned to a new name.
6.Press the EXIT button to exit.
Use fine tuning to manually adjust a particular channel for optimal
reception.
1. Use the number buttons to directly select the channel that
you want to fine tune.
2. Press the MENU button to display the menu. Press the or button to select “Channel”, then press the ENTER button.
3.Press the or button to select “Fine Tune”, then press the ENTER button.
4.Press the or button to adjust the fine tuning. Press the ENTER button.
5.Press the EXIT button to exit.
Fine tuned channels that have been saved are marked with an asterisk “ * ” on the right-hand side of the channel number in the channel banner. And the channel number turns red.
To reset the fine-tuning, select “Reset” by pressing the or button and then press the ENTER button.
English-11
You can select the type of picture which best corresponds to your
viewing requirements.
1. Press the MENU button to display the menu. Press the or
|
|
|
|
|
|
|
|
button to select “Picture”, then press the ENTER button. |
|
|
|
|
|
|
|
2. |
Press the ENTER button again, to select “Mode”. |
||
|
|
|
|
|
|
|
|
Press the ENTER |
button again. |
|
|
|
|
3. |
Press the or button to select the desired picture effect. |
||||
|
|
|
|
|
|
|
|
Press the ENTER |
button. |
|
|
|
|
4. |
|||||
|
|
|
|
Press the EXIT button to exit. |
You can also press the P.MODE button on the remote control to select one of the picture settings.
Dynamic: Selects the picture for high-definition in a bright room.
Standard: Selects the picture for optimum display in a normal environment.
Movie: Selects the picture for comfortable display in a dark room.
Custom: Select to view your favorite display settings.
(Refer to “Adjusting the Custom Picture”)
The Picture mode must be adjusted separately for each input source.
You can return to the factory defaults picture settings by selecting the “Reset”. (Refer to “Resetting the Picture Settings to the Factory Defaults” on page 13)
Your set has several settings which allow you to control picture quality.
1. To select the desired picture effect, follow the
“Changing the Picture Standard” instructions number 1 to 4.
2. Press the or button to select a particular item.
Press the ENTER button.
3. Press the or button to decrease or increase the value of a particular item. Press the ENTER button.
4.Press the EXIT button to exit.
Contrast: Adjusts the lightness and darkness between objects and the background.
Brightness: Adjusts the brightness of the whole screen.
Sharpness: Adjusts the outline of objects to either sharpen them or make them more dull.
Colour: Adjusts the colours, making them lighter or darker.
Tint (NTSC only): Adjusts the colour of objects, making them more red or green for a more
natural look.
The adjusted values are stored according to the selected Picture mode.
In PC Mode, Only “Contrast”, “Brightness” and “Colour” can be adjusted
You can select the most comfortable colour tone to your eyes.
1. To select the desired picture effect, follow the
“Changing the Picture Standard” instructions number 1 to 4
2. Press the or button to select “Colour Tone”, then press the ENTER button.
3. Press the or button to select the desired colour tone setting. Press the ENTER button.
4.Press the EXIT button to exit.
Cool2: Makes the colour temperature bluer than “Cool1” menu.
Cool1: Makes whites bluish.
Normal: Keeps whites white.
Warm1: Makes whites reddish.
Warm2: Makes the colour temperature redder than “Warm1” menu.
The adjusted values are stored according to the selected Picture mode.
English-12
You can return to the factory defaults picture settings.
|
|
|
1. |
To select the desired picture effect, follow the |
|||||
|
|
|
|||||||
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
“Changing the Picture Standard” instructions number 1 to 4 on page 12. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Press the or button to select “Reset”, then press the |
||
|
|
|
|
|
|
|
2. |
||
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
ENTER button. |
|
|
|
|
|
|
|
|
|
|
|
|
3. |
Press the EXIT button to exit. |
The “Reset” will be set for each picture mode.
You can select the picture size which best corresponds to your
viewing requirements.
1. Press the MENU button to display the menu. Press the or button to select “Picture”, then press the ENTER button.
2.Press the or button to select “Size”, then press
the ENTER button.
You can select these options by simply pressing the P.Size button on the remote control.
3.Select the required option by pressing the or button. Press the ENTER button.
4.Press the EXIT button to exit.
Auto Wide: Automatically adjusts the picture size to the "16:9" aspect ratio.
16:9: Adjusts the picture size to 16:9 appropriate for DVDs or wide broadcasting.
Zoom: Magnifies the 16:9 wide picture (in the vertical direction) to fit the screen size.
4:3: This is the default setting for a video movie or normal broadcasting.
“Auto Wide” function is available only in "TV", "Ext1", "Ext2", "AV", and "S-Video" mode. In PC Mode, only “16:9” and “4:3” mode can be adjusted.
Select by pressing the or buttons. Use the or button to move the
picture up and down. After selecting , use the or button to magnify or reduce the picture size in the vertical direction.
Press the STILL button to freeze a moving picture into a still one. Press again to cancel.
If the broadcast signal received by your TV is weak, you can activate the
Digital Noise Reduction feature to help reduce any static and ghosting
that may appear on the screen.
1. Press the MENU button to display the menu. Press the or button to select “Picture”, then press the ENTER button.
2. Press the or button to select “Digital NR”, then press the ENTER button.
3.Press the or button to select “On” or “Off”. Press the ENTER button.
4.Press the EXIT button to exit.
English-13
Samsung’s new technology brings you more detailed images with
contrast and white enhancement. A new image compensation algorithm
gives viewers brighter and clearer images. DNIe technology will match
every signal to your eyes. You can see how DNIe improves the picture by setting DNIe Demo mode to On.
1. Press the MENU button to display the menu. Press the or button to select “Picture”, then press the ENTER button.
2.Press the or button to select “DNIe Demo”, then press the ENTER button.
3.Press the or button to select “On” or “Off”. Press the ENTER button.
4.Press the EXIT button to exit.
These functions don’t work in PC mode.
The DNle Demo is designed to show the difference between the regular and
DNIe pictures.
By default, the product displays the picture with DNle applied.
You can display a sub picture within the main picture of set
programme or video input. In this way, you can watch the picture of set
programme or video input from any connected equipment while watching the main picture.
1.Press the MENU button to display the menu. Press the or button to
select “Picture”, then press the ENTER button.
Press the PIP button on the remote control repeatedly to activate or deactivate the “PIP”.
2.Press the or button to select “PIP”, then press the ENTER button.
3.Press the ENTER button again.
Press the or button to select “On”, then press ENTER button.
If the PIP is activated, the size of the main picture turns to “16:9”.
4.Press the or button to select “Source”,
then press ENTER button. Select a source of the sub picture by pressing the or button and press the ENTER button.
The sub picture can serve different source selections based on what the main picture is set to.
5.Press the or button to select “Swap”.
To interchange the main picture and the sub picture, select “Swap” option and press the ENTER button.
The main picture and the sub picture are interchanged.
If main picture is in “PC” mode, “Swap” is not available.
6.Press the or button to select “Size” of the sub picture and then press the ENTER button. Select a size of the sub picture by pressing the or button and then press the ENTER button.
If main picture is in “PC” mode, “Size” is not available.
7.Press the or button to select “Position”, then press the ENTER button. Select the position of the sub picture by pressing the or button and then press the ENTER button.
Continued…
English-14
8.Press the or button to select “Programme” and then press the ENTER button. You can select the channel that you want to view through sub picture by pressing the or button.
Press the ENTER button.
The “Programme” can be active when the sub picture is set to TV.
9.Press the EXIT button to exit.
You may notice that the picture in the PIP window becomes slightly unnatural when you use the main screen to view a game or karaoke.
Source: Used to select a source of the sub picture.
Swap: Used to interchange the main picture and the sub picture.
Size: Used to select a size of the sub picture.
Position: Used to move the sub picture.
Programme: Used to Change the sub picture.
PIP Settings (O: PIP operates, X: PIP doesn’t operate) |
|
|
|
|
|
||||
Main Sub |
TV |
Ext.1 |
Ext.2 |
AV |
S-Video |
Component |
PC |
HDMI |
|
TV |
X |
X |
X |
X |
X |
X |
X |
O |
|
Ext.1 |
X |
X |
X |
X |
X |
X |
X |
O |
|
Ext.2 |
X |
X |
X |
X |
X |
X |
X |
O |
|
AV |
X |
X |
X |
X |
X |
X |
X |
O |
|
S-Video |
X |
X |
X |
X |
X |
X |
X |
O |
|
Component |
X |
X |
X |
X |
X |
X |
X |
O |
|
PC |
O |
O |
O |
O |
X |
X |
X |
X |
|
HDMI |
O |
O |
O |
O |
O |
O |
X |
X |
You can select the type of the special sound effect to be used when watching a given broadcast.
1. |
Press the MENU button to display the menu. Press the or button to |
|
select “Sound”, then press the ENTER button. |
2. |
Press the ENTER button again, to select “Mode”. |
3. |
Select the required sound effect by pressing the or button repeatedly |
|
and then press the ENTER button. |
4. |
Press the EXIT button to exit. |
You can also select these options by simply pressing the S.MODE button on the remote control.
Standard: Selects the normal sound mode.
Music: Emphasizes music over voices.
Movie: Provides live and full sound for movies.
Speech: Emphasizes voices over other sounds.
Custom: Selects your custom sound settings. (Refer to “Adjusting the Sound Settings”)
The sound settings can be adjusted to suit your personal preferences.
1. |
Press the MENU button to display the menu. Press the or button to |
|
select “Sound”, then press the ENTER button. |
2. |
Press the or button to select “Equalizer”, then press the |
|
ENTER button. |
3. |
Press the or button to select a particular item. |
|
Press the ENTER button. |
4.Press the or Press the ENTER
button to reach the required setting. button.
5.Press the EXIT button to exit.
If you make any changes to these settings, the Sound Mode is automatically switched to “Custom”.
English-15
TruSurround XT is a patented SRS technology that solves the problem of |
playing 5.1 multichannel content over two speakers. |
TruSurround delivers a compelling,virtual surround sound experience |
through any two-speaker playback system, including internal television |
speakers. It is fully compatible with all multichannel formats. |
1. Press the MENU button to display the menu. Press the or button to select “Sound”, then press the ENTERbutton.
2. |
Press the or button to select “SRS TSXT”, then press the |
|
ENTER button. |
3. |
Press the or button to select “On” or “Off”. Press the ENTER button. |
You can also set these options 4. |
Press the EXIT button to exit. |
simply by pressing the SRS |
TruSurround XT, SRS and |
symbol are trademarks of |
|
button on remote control. |
|||
SRS Labs, Inc. TruSurround XT technology is incorporated under |
license from SRS Labs, Inc.
Each broadcasting station has its own signal conditions, and so it is not
easy for you to adjust the volume every time the channel is changed.
This feature allows you to automatically adjust the volume of the desired
channel by lowering the sound output when the modulation signal is high
or by raising the sound output when the modulation signal is low.
1. Press the MENU button to display the menu. Press the or button to select “Sound”, then press the ENTER button.
2.Press the or button to select “Auto Volume”, then press the ENTER button.
3.Press the or button to select “On” or “Off”. Press the ENTER button.
4.Press the EXIT button to exit.
If you want to hear the sound through separate speakers, cancel the internal amplifier.
1. |
Press the MENU button to display the menu. Press the or button to |
|
|
|
select “Sound”, then press the ENTER button. |
|
|
|
2. |
Press the or button to select “Internal Mute”, then press the |
|
|
|
ENTER button. |
3.Press the or button to select “On” or “Off”. Press the ENTER button.
4.Press the EXIT button to exit.
When “Internal Mute” is set to “On’, the Sound menus except for “Sound Select” (in PIP mode) cannot be adjusted.
English-16
During the PIP features activation, you can listen to the sound of the sub picture.
1. |
Press the MENU button to display the menu. Press the or button to |
||
|
|
select “Sound”, then press the ENTER button. |
|
|
2. |
Press the or button to select “Sound Select”, then press the ENTER |
button. |
|
|||
3. |
Press the or button to select “Sub”. Press the ENTER |
button. |
4.Press the EXIT button to exit.
Main: Used to listen to the sound of the main picture.
Sub: Used to listen to the sound of the sub picture.
You can select this option when the “PIP” is set to “On”.
If Game Mode is On, the Reset Sound function is activated. Selecting
the Reset function after setting the equalizer resets the equalizer
setting to the factory defaults.
1. Press the MENU button to display the menu. Press the or button to select “Sound”, then press the ENTER button.
2.Press the or button to select “Reset”, then press the ENTER button.
3. Press the EXIT button to exit.
You can select this option when the “Game Mode” is set to “On”.
You can connect a set of headphones to your set if you wish to watch a TV programme without disturbing the other people in the room.
When you insert the head set jack into the corresponding port,
you can operate only "Internal Mute" and "Sound Select" (in PIP mode) in Sound menu. Prolonged use of headphones at a high volume may damage your hearing.
You will not receive sound from the speakers when you connect headphones to the system.
You can set the TV’s clock so that the current time is displayed when
you press the INFO button. You must also set the time if you wish to use the automatic On/Off timers.
1.Press the MENU button to display the menu. Press the or button to select “Setup”, then press the ENTER button.
2. Press the or button to select “Time”, then press the ENTER button.
3.Press the ENTER button to select “Clock Set”.
4. |
|
|
|
To... |
|
Press the... |
|
|
Move to “Hour” or “Minute” |
or button. |
|
|
Set the “Hour” or “Minute” |
or button. |
|
|
Press the ENTER |
button. |
|
|
|
|
|
5.Press the EXIT button to exit.
If you disconnect the power cord, you have to set the clock again.
You can also set hour and minute by pressing the number buttons on the remote control.
English-17
|
You can select a time period of between 30 and 180 minutes after which |
|
|
the television automatically switches to standby mode. |
|
|
1. |
Press the MENU button to display the menu. Press the or button to |
|
|
select “Setup”, then press the ENTER button. |
|
2. |
Press the or button to select “Time”, then press the ENTER button. |
|
3. |
Press the or button to select “Sleep Timer”, then press the |
|
|
ENTER button. |
|
4. |
Press the or button repeatedly until the desired time appears |
|
|
(Off, 30, 60, 90, 120, 150, 180). Press the ENTER button. |
Press the SLEEP button on the |
5. |
Press the EXIT button to exit. |
remote control repeatedly until |
|
The TV automatically switches to standby mode when the timer reaches 0. |
the appropriate time interval |
|
appears.
You can set the On/Off timers so that the set will:
Switch on automatically and tune to the channel of your choice at
the time you select.
Switch off automatically at the time you select.
The first step is to set the television’s clock.
1. Press the MENU button to display the menu. Press the or button to
select “Setup”, then press the ENTER button.
2. Press the or button to select “Time”, then press the ENTER button.
3.Press the or button to select “On Timer”, then press the ENTER button.
4.Press the or button to adjust “Hour”, then press the button to move to the next step. Set other items using the same method as above. When finished, press the ENTER button to return.
5.Press the or button to select “Off Timer”, then press the ENTER button.
6.Press the or button to adjust “Hour”, then press the button to move to the next step. Set other items using the same method as above. When finished, press the ENTER button to return.
7.Press the EXIT button to exit.
You can also set hour and minute by pressing the number buttons on the remote control.
The "Activation" setting must be set to "Yes" in order for the timers to work.
English-18
When you start using your set for the first time, you must select the
language which will be used for displaying menus and indications.
1. Press the MENU button to display the on-screen menu.
Press the or button to select “Setup”, then press the
ENTER button.
2. Press the or button to select “Language”, then press the ENTER button.
3.Select a particular language by pressing the or button repeatedly. Press the ENTER button.
You can choose one of 21 languages.
4.Press the EXIT button to exit.
When connecting to a game console such as PlayStationTM or XboxTM,
you can enjoy a more realistic gaming experience by selecting game menu.
1. Press the MENU button to display the menu. Press the or button to select “Setup”, then press the ENTER button.
2. Press the or button to select “Game Mode”, then press the ENTER button.
3.Press the or button to select “On” or “Off”. Press the ENTER button.
4.Press the EXIT button to exit.
To disconnect the game console and connect another external device, cancel game mode in the picture menu.
If you display the TV menu in Game mode, the screen shakes slightly. Game Mode is not available in TV mode.
If Game Mode is On:
•Picture Mode and Sound Mode are automatically changed to Custom and users can not change the mode.
•Sound Mode in the Sound menu is deactivated. Adjust the sound using the equalizer.
•The Reset Sound function is activated. Selecting the Reset function after setting the equalizer resets the equalizer setting to the factory defaults.
Blue Screen:
If no signal is being received or the signal is very weak, a blue screen auto-
matically replaces the noisy picture background. If you wish to continue
viewing the poor picture, you must set the "Blue Screen" mode to "Off".
Melody:
You can hear melody sound when the television is powered on or off.
1.Press the MENU button to display the menu. Press the or button to select “Setup”, then press the ENTER button.
2.Press the or button to select “Blue Screen” or “Melody”. Press the ENTER button.
3.Press the or button to select “On” or “Off”. Press the ENTER button.
4.Press the EXIT button to exit.
English-19
This function adjusts the brightness of the TV so as to reduce power
consumption. When you watching TV at night, set the "Energy Saving "
mode option to "High" so as to reduce the dazzling of your eyes as well
as the power consumption.
1. Press the MENU button to display the on-screen menu. Press the or button to select “Setup”, then press the ENTER button.
2.Press the or button to select “Energy Saving”, then press the ENTER button.
3.Select the required option (Off, Low, Medium, High) by pressing the or button. Press the ENTER button.
4.Press the EXIT button to exit.
You can select among external sources connected to
your TV’s input jacks.
1. Press the MENU button to display the menu.
Press the ENTER button, to select “Input”.
2. Press the ENTER button again, to select “Source List”.
When no external device is connected to your set, only “TV”, “Ext.1”, “Ext.2”
are activated in the “Source List”. “AV”, “S-Video”, “Component”, “PC”, “HDMI”
are activated only when they are connected to your set.
3. Select the required device by pressing the or button.
Press the ENTER button.
Press the SOURCE button on the remote control to toggel between all the available
source. TV mode can be selected by pressing the TV button, number buttons(0~9), and the P/ button on the remote control. But it cannot be selected using the SOURCE button.
You can select PC mode by simply pressing the PC button on the remote control.
Name the device connected to the input jacks to make your input
source selection easier.
1. Press the MENU button to display the menu.
Press the ENTER button, to select “Input”.
2. Press the or button to select “Edit Name”, then press the ENTER button.
3.Press the or button to select the device that you wish to edit. Press the ENTER button.
4.Press the or button to select the required device. Press the ENTER button.
5.Press the EXIT button to exit.
English-20
Most set channels carry “ teletext ”, pages of written information that provide information such as:
Television programme times.
News bulletins and Weather forecasts.
Sports results.
Subtitles for the hard of hearing.
The teletext pages are organized according to six categories:
Part |
Contents |
A |
Selected page number. |
B |
Broadcasting station identity. |
C |
Current page number or search status. |
D |
Date and time. |
E |
Text. |
F |
Status information. |
You can display teletext information at any time, but signal reception must be good. Otherwise:
Information may be missing.
Some pages may not be displayed.
To activate the teletext mode and display the contents page:
1.Using the P () or P () button, select the channel providing the
teletext service.
2. Press the TTX/MIX () button to activate the teletext mode.
The contents page is displayed. It can be redisplayed at any time by pressing the MENU () button.
3. Press the TTX/MIX () button again.
The actual broadcast will be displayed with “Teletext”, “Double”, and “Mix” in order on the screen.
4. Press the TV( ) button to exit from the Text display.
If any broken character appears while Text is being viewed, make sure that the
Text language is identical with the language in the “Setup” menu mode. If both languages are different, select the same language with the Text language on the “Setup” menu.
English-21
Press the number buttons on the remote control to enter the page number directly:
1.Enter the three-digit page number listed in the contents by pressing the
corresponding numeric buttons.
2.If the selected page is linked with several secondary pages, the secondary
pages are displayed in sequence. To freeze the display on a given page, press the PIP ( ) button. Press the PIP ( ) button again to resume.
3. Using the various display options:
To display... |
Press the... |
|
||
Both teletext information and the normal broadcast |
TTX/MIX ( |
) |
||
Hidden text (answers to quiz games, for example) |
INFO ( |
) |
|
|
The normal screen |
INFO ( |
) |
|
|
A secondary page, by entering its 4-digit number |
PRE-CH ( |
) |
||
The next page |
P |
( |
) |
|
The previous page |
P |
( |
) |
|
Double-size letters in the: |
SOURCE ( |
) |
||
Upper half of the screen |
Once |
|
|
|
Lower half of the screen |
Twice |
|
|
|
Normal screen |
Three times |
The various topics included in the teletext pages are colour-coded, and can be selected by pressing the coloured buttons on the remote control.
1. Display the teletext contents page by pressing the TTX/MIX () button.
2. Press the coloured button corresponding to the topic that you wish to select (The available topics are listed on the status information line).
3. Press the Red button to display the previous page. Press the Green button to display the next page.
4. Press the TV() button to exit from the Text display.
English-22
The Windows display-settings for a typical computer are shown below. The actual screens on your PC may be different depending upon your particular version of Windows and your particular video card. Even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1.First, click on “Control Panel” on the Windows start menu.
2.When the control panel window appears, click on “Appearance and Themes” and a display dialog-box will appear.
3.When the control panel window appears, click on “Display” and a display dialog-box will appear.
4.Navigate to the “Settings” tab on the display dialog-box. The correct size setting (resolution): Optimum1360 X 768
If a vertical-frequency option exists on your display settings dialog box, the correct value is “60” or “60 Hz”. Otherwise, just click “OK” and exit the dialog box.
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The resolutions in the table are recommended. (All resolutions between the supported limits are supported)
Mode |
Resolution |
Horizontal |
Vertical |
Pixel Clock |
Sync Polarity |
|
|
Frequency (kHz) |
Frequency (Hz) |
Frequency (MHz) |
(H/V) |
IBM |
640 x 480 |
31.469 |
59.940 |
25.175 |
- / - |
|
720 x 400 |
31.469 |
70.087 |
28.322 |
- / + |
VESA |
640 x 480 |
37.861 |
72.809 |
31.500 |
- / - |
|
640 x 480 |
37.500 |
75.000 |
31.500 |
- / - |
|
800 x 600 |
37.879 |
60.317 |
40.000 |
+ /+ |
|
800 x 600 |
48.077 |
72.188 |
50.000 |
+ /+ |
|
800 x 600 |
46.875 |
75.000 |
49.500 |
+ /+ |
|
1024 x 768 |
48.364 |
60.000 |
65.000 |
- / - |
|
1024 x 768 |
56.476 |
70.069 |
75.000 |
- / - |
|
1024 x 768 |
60.023 |
75.029 |
78.750 |
+ /+ |
|
1360 x 768 |
47.712 |
60.015 |
85.800 |
+ /+ |
|
|
|
|
|
|
The interface mode is not supported.
The set might operate abnormally if a non-standard video format is selected.
DVI does not support PC function.
Separate and Composite modes are supported. SOG is not supported.
English-23
Coarse and Fine Tuning of the Image (Image Lock):
The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not removed by Fine-tuning alone, then adjust the frequency as best as possible (coarse) and Fine-tune again. After the noise has been reduced, re-adjust the picture so that it is aligned on the center of screen.
1. Preset: Press the PC button to select PC mode.
Press the PC button on the remote control to select the PC mode.
2.Press the MENU button to display the menu. Press the or button to select “Setup”, then press the ENTER button.
3.Press the or button to select “PC”, then press the ENTER button.
4.Press the ENTER button to select “Image Lock”.
5.Press the or button to select “Coarse” or “Fine”, then press the ENTER button.
6.Press the or button to adjust the screen quality. Press the ENTER button.
7.Press the EXIT button to exit.
Changing the Image Position (Position):
Adjust the PC’s screen positioning if it does not fit the TV screen.
1. Follow the “Coarse and Fine Tuning of the Image (Image Lock)” instructions number 1 to 3.
2. Press the or button to select “Position”, then press the ENTER button.
3.Press the or button to adjusting the Vertical-Position. Press the or button to adjust the Horizontal-Position. Press the ENTER button.
4.Press the EXIT button to exit.
Adjusting the PC Screen Automatically (Auto Adjustment):
Auto adjustment allows the PC screen of set to self-adjust to the incoming PC video signal. The values of fine, coarse and position are adjusted automatically.
1.Follow the “Coarse and Fine Tuning of the Image (Image Lock)”
instructions number 1 to 3.
2.Press the or button to select “Auto Adjustment”, then press the ENTER button.
3.Press the EXIT button to exit.
Initializing the Image Settings (Image Reset):
You can replace all image settings with the factory default values.
1. Follow the “Coarse and Fine Tuning of the Image (Image Lock)” instructions number 1 to 3.
2.Press the or button to select “Image Reset”,
then press the ENTER button.
3.Press the EXIT button to exit.
English-24
The Kensington lock is a device used to physically fix the system when using it in a public place.
The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Please refer to the manual provided with the Kensington lock for proper use.
Cable
Figure 2
Figure 1
<Optional>
1.Insert the locking device into the Kensington slot on the LCD TV (Figure 1), and turn it in the locking direction (Figure 2).
2.Connect the Kensington lock cable.
3.Fix the Kensington lock to a desk or a heavy stationary object.
The place of the Kensington Lock may be different depending on its model.
No sound or picture |
Check that the mains lead has been connected to a wall socket. |
|
|
Check that you have pressed the |
button on the front of the set. |
|
Check the picture contrast and brightness settings. |
|
|
Check the volume. |
|
Normal picture but no sound |
Check the volume. |
|
|
Check whether the MUTE button has been pressed on the remote control. |
|
|
Check if “Internal Mute” is off |
|
No picture or black and white picture Adjust the colour settings.
Check that the broadcast system selected is correct.
Sound and picture interference |
Try to identify the electrical appliance that is affecting the set and move it further away. |
|
Plug your set into a different mains socket. |
|
|
Blurred or snowy picture, |
Check the direction, location and connections of your aerial. |
distorted sound |
This interference is often due to the use of an indoor aerial. |
Remote control malfunctions |
Replace the remote control batteries. |
|
Clean the upper edge of the remote control (transmission window). |
|
Check the battery terminals. |
“Check signal cable.” |
Check that the signal cable is firmly connected to the PC or video sources. |
message is displayed. |
Check that the PC or video sources are turned on. |
On PC mode, “Mode Not Supported.” Check the maximum resolution and the frequency of the video adaptor. message is displayed. Compare these values with the data in the Display Modes.
The TFT LCD panel uses a panel consisting of sub pixels (3,133,440) which require sophisticated technology to produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.
English-25
Model Name |
LE32S6 |
ScreenSize(Diagonal) |
32 inch |
Power Supply |
AC 220-240 V 50 Hz |
Power Consumption |
152 W |
PC Resolution |
1360 x 768 @ 60 Hz |
Sound |
|
Output |
10 W X 2 |
Dimension (WxDxH) |
|
Body |
892.5 x 82.0 x 544.0 mm |
With stand |
892.5 x 249.0 x 615.0 mm |
Weight |
|
With stand |
13.9 kg |
Environmental Considerations |
|
Operating Temperature |
10 °C to 40 °C (50 °F to 104 °F) |
Operating Humidity |
10 % to 80 %, non-condensing |
Storage Temperature |
-20 °C to 45 °C (-4 °F to 11 3 °F) |
Storage Humidity |
5 % to 95 %, non-condensing |
Model Name |
LE37S6 |
LE40S6 |
|
|
|
ScreenSize(Diagonal) |
37 inch |
40 inch |
Power Supply |
AC 220-240 V 50 Hz |
AC 220-240 V 50 Hz |
Power Consumption |
170 W |
205 W |
|
|
|
PC Resolution |
1360 x 768 @ 60 Hz |
1360 x 768 @ 60 Hz |
Sound |
|
|
Output |
10 W X 2 |
10 W X 2 |
Dimension (WxDxH) |
|
|
Body |
1026.5 × 94.1 × 626.1 mm |
1100.5 x 95.0 x 661.0 mm |
With stand |
1026.5 × 330.0 × 698.8 mm |
1100.5 x 330.0 x 732.5 mm |
Weight |
|
|
With stand |
22.5 kg |
23.7 kg |
Environmental Considerations |
|
|
Operating Temperature |
10 °C to 40 °C (50 °F to 104 °F) |
10 °C to 40 °C (50 °F to 104 °F) |
Operating Humidity |
10 % to 80 %, non-condensing |
10 % to 80 %, non-condensing |
Storage Temperature |
-20 °C to 45 °C (-4 °F to 11 3 °F) |
-20 °C to 45 °C (-4 °F to 11 3 °F) |
Storage Humidity |
5 % to 95 %, non-condensing |
5 % to 95 %, non-condensing |
Design and specifications are subject to change without prior notice.
This device is a Class B digital apparatus.
For the power supply, refer to the label attached to the product.
English-26
This page is intentionally left blank.
Elővigyázatosság az állóképek megjelenítésével kapcsolatban.
Az állóképek a TV-képernyő maradandó károsodását okozhatják.
•Ne jelenítsen meg állóképeket az LCD-képernyőn 2 órát meghaladó időn túl, mert ilyenkor a megjelenített képek a képernyő „beégését” okozhatják.
Ezt a jelenséget „képernyőbeégésnek” is nevezik.
A képernyőbeégés elkerülése érdekében állókép megjelenítésekor csökkentse a kép fényerejét és kontrasztját.
•Az LCD TV huzamosabb ideig tartó, 4:3 képarányú módban történő használata esetén a kibocsátott fényerősség eltérése
miatt a képernyő közepén, valamint bal és jobb oldalán sávok alakulhatnak ki. DVD-filmek lejátszása és játékprogramok használata is hasonló jelenséget okozhat. A garancia az ilyen esetekben keletkezett károkra nem terjed ki.
•Videojátékok vagy számítógépek állóképeinek bizonyos időt meghaladó megjelenítése következtében a képernyőn részleges utókép jelenhet meg. A jelenség megelőzése érdekében állóképek megjelenítése esetén csökkentse a fényerőt és kontrasztot.
©2007 Samsung Electronics Co., Ltd. All rights reserved.