Size:
3.91 Mb
Download
D3-4-2-1-7a_A_En
D3-4-2-1-4_A_En
D3-4-2-1-7b_A_En
D3-4-2-1-3_A_En

Thank you for buying this Pioneer product.

Please read through these operating instructions so that you will know how to operate your model properly. After you have finished reading the instructions, put them in a safe place for future reference.

Location: bottom of the unit

IMPORTANT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

D3-4-2-1-1_En-A

WARNING

This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filed with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.

WARNING

Before plugging in for the first time, read the following section carefully.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230 V or 120 V) written on the rear panel.

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

For Taiwan exclusively

Taiwanese two pin flat-bladed plug

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 10 cm at top, 10 cm at rear, and 10 cm at each side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

CAUTION

The STANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-2a_A_En

D3-4-2-2-1a_A_En
K041_En
S002_En
D3-4-2-1-7c_A_En

CAUTION

This product is a class 1 laser product, but this product contains a laser diode higher than Class 1.

To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.

One of the following caution labels appears on your unit. Location: top of the unit

CAUTION : CLASS 3B VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN, AVOID

EXPOSURE TO THE BEAM.

VRW2159

CLASS 1

LASER PRODUCT

D3-4-2-1-8_B_En

POWER-CORD CAUTION

Operating Environment

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.

This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.

Operating environment temperature and humidity: +5 ºC – +35 ºC (+41 ºF – +95 ºF); less than 85 %RH (cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal.

The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).

Contents

01 Controls and displays

Front panel . . . . . . . . . . . . . . . . . . . . . . . . .6 Remote control . . . . . . . . . . . . . . . . . . . . . .6 Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

02 Getting started

Home theater sound setup . . . . . . . . . . . . .9 Using the Auto MCACC setup for optimal surround sound . . . . . . . . . . . . . . . . . . . . . .9

Using the on-screen displays . . . . . . . . . . .10

Playing discs . . . . . . . . . . . . . . . . . . . . . . .11

Basic playback controls. . . . . . . . . . . . . .11 Resume and Last Memory. . . . . . . . . . . .11 DVD-Video disc menus . . . . . . . . . . . . . .12 Video CD/Super VCD PBC menus . . . . . .12 Listening to the radio . . . . . . . . . . . . . . . . .12 Improving poor FM reception . . . . . . . . .12 Reducing AM reception noise . . . . . . . . .13 Memorizing stations . . . . . . . . . . . . . . . .13 Listening to station presets . . . . . . . . . . .13 Listening to other sources . . . . . . . . . . . . .13

03 Listening to your system

Auto listening mode . . . . . . . . . . . . . . . . .14

Listening in surround sound . . . . . . . . . . .14 Dolby Pro Logic II Music settings . . . . . .14 Using Front Surround . . . . . . . . . . . . . . . .15 Using Advanced Surround. . . . . . . . . . . . .15

Listening in stereo . . . . . . . . . . . . . . . . . . .15

Listening with headphones . . . . . . . . . . . .15 Listening with Acoustic Calibration EQ . . .15 Using the Sound Retriever . . . . . . . . . . . . .16

Enhancing dialog. . . . . . . . . . . . . . . . . . . .16

Using the Tone controls. . . . . . . . . . . . . . .16 Adjusting the bass and treble . . . . . . . . .16 Quiet and Midnight modes . . . . . . . . . . .16 Boosting the bass level . . . . . . . . . . . . . . .16

04 Disc playback features

Scanning discs . . . . . . . . . . . . . . . . . . . . .17

Playing in slow motion. . . . . . . . . . . . . . . .17 Frame advance/frame reverse . . . . . . . . . .17 Playing a JPEG slideshow . . . . . . . . . . . . .17 Browsing DVD or Video CD/Super VCD discs with the Disc Navigator . . . . . . . . . . . . . . .18 Browsing WMA, MP3, MPEG-4 AAC, DivX video and JPEG files with the Disc

Navigator . . . . . . . . . . . . . . . . . . . . . . . . . .19

Looping a section of a disc . . . . . . . . . . . .19

Using repeat play. . . . . . . . . . . . . . . . . . . .19 Using random play . . . . . . . . . . . . . . . . . .20

4

Creating a program list . . . . . . . . . . . . . . . 20 Other functions available from the program menu . . . . . . . . . . . . . . . . . . . . 21

Searching a disc . . . . . . . . . . . . . . . . . . . . 21 Switching subtitles . . . . . . . . . . . . . . . . . . 21

Switching language / audio channels . . . . 21

Zooming the screen . . . . . . . . . . . . . . . . . 22

Switching camera angles . . . . . . . . . . . . . 22 Displaying disc information. . . . . . . . . . . . 22

05 USB playback

Using the USB interface . . . . . . . . . . . . . . 23 Basic playback controls . . . . . . . . . . . . . . 23

Scanning files . . . . . . . . . . . . . . . . . . . . . . 24

Playing a JPEG slideshow . . . . . . . . . . . . . 24 Browsing files with the Navigator . . . . . . . 24

06 Surround sound settings

Using the Setup menu . . . . . . . . . . . . . . . 25

07 Video Adjust menu

Video Adjust menu . . . . . . . . . . . . . . . . . . 26

08 Initial Settings menu

Using the Initial Settings menu . . . . . . . . . 27 Video Output settings . . . . . . . . . . . . . . . . 27

Language settings. . . . . . . . . . . . . . . . . . . 27 Display settings. . . . . . . . . . . . . . . . . . . . . 28 Options settings . . . . . . . . . . . . . . . . . . . . 28 Parental Lock . . . . . . . . . . . . . . . . . . . . . 28

About DivX® VOD content . . . . . . . . . . . 29

09 Other connections

Connecting external antennas. . . . . . . . . . 31 Connecting auxiliary audio components . . 31 Connecting the S-video output . . . . . . . . . 31 Connecting using the component video output . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

About progressive scan video . . . . . . . . . 32 Using this unit with a Pioneer plasma display. . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

SR+ Setup for Pioneer plasma

displays. . . . . . . . . . . . . . . . . . . . . . . . . . 33

Switching on the SR+ mode. . . . . . . . . . 33

En

10 Additional information

Optional system settings . . . . . . . . . . . . . 34 Setting the sleep timer . . . . . . . . . . . . . . . 35

Dimming the display . . . . . . . . . . . . . . . . 35

Disc / content format playback

compatibility . . . . . . . . . . . . . . . . . . . . . . 35

Disc compatibility table . . . . . . . . . . . . . 36 About DVD+R/DVD+RW compatibility . 36

About DivX. . . . . . . . . . . . . . . . . . . . . . . 36 About MPEG-4 AAC . . . . . . . . . . . . . . . . 37 About WMA . . . . . . . . . . . . . . . . . . . . . . 37

Using and taking care of discs . . . . . . . . . 38

DVD Video regions. . . . . . . . . . . . . . . . . 38

Installation and maintenance . . . . . . . . . .38 Hints on installation . . . . . . . . . . . . . . . .38 Cleaning the pickup lens . . . . . . . . . . . . .39 Problems with condensation. . . . . . . . . .39 Moving the system unit . . . . . . . . . . . . . .39

Screen sizes and disc formats . . . . . . . . . .39

Troubleshooting. . . . . . . . . . . . . . . . . . . . .40 General . . . . . . . . . . . . . . . . . . . . . . . . . .40

DVD/CD/Video CD player. . . . . . . . . . . . .41

Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . . .42 USB connection . . . . . . . . . . . . . . . . . . .42 Error Messages . . . . . . . . . . . . . . . . . . . .42 Resetting the system . . . . . . . . . . . . . . . . .43

Using the language code list . . . . . . . . . . .43

Language code list . . . . . . . . . . . . . . . . . .44

Country/Area code list . . . . . . . . . . . . . . . .44

Specifications . . . . . . . . . . . . . . . . . . . . . .45

EspaÒol Nederlands Italiano FranÁais Deutsch English

5

En

01 Controls and displays

Chapter 1

Controls and displays

Front panel

Remote control

OPEN/CLOSE DVD/CD USB VOLUME STANDBY/ON

1

2

3

4

5

6

9

78

1 OPEN/CLOSE

Opens/closes the disc tray.

2DVD/CD

Selects the DVD/CD function and starts/ pauses/resumes playback.

3

Stops playback.

4USB

Selects the USB function and starts/pauses playback.

5VOLUME buttons

6STANDBY/ON

Switches the system on or into standby.

7USB interface

Connect a USB device for playback (see USB playback on page 23).

8 PHONES jack

Connect headphones.

9Display

See Display below.

6

 

STANDBY

DVD/CD

TUNER

 

 

1

/ON

(FM/AM)

 

 

 

 

 

 

OPEN/

 

2

 

 

USB

LINE

CLOSE

11

 

 

 

 

 

 

 

 

 

 

 

 

 

AUDIO

 

 

1

 

2

3

 

 

 

 

 

 

 

SUBTITLE

 

3

4

 

5

6

 

12

 

 

 

 

ANGLE

 

7

 

8

9

 

 

 

CLEAR

 

 

DISPLAY

ZOOM

 

 

 

 

 

 

 

 

 

0

 

 

 

4

TOPMENU

 

TUNE

 

MENU

13

SETUP

 

 

 

SR

5

 

 

 

 

ST

 

ENTER

ST

 

 

HOME

 

 

 

 

 

 

MENU

 

 

 

RETURN

 

6

 

 

 

 

14

MCACC

TUNE

 

TEST TONE

 

 

 

 

 

7

SOUND

 

 

 

 

 

RETRIEVER

SURROUND

ADVANCED

SOUND

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

 

TV CONTROL

 

SLEEP

15

9

 

 

 

 

 

INPUT

CHANNEL

VOLUME

MUTE

16

 

SHIFT

 

 

 

 

10

 

 

VOLUME

 

17

 

 

 

 

 

1STANDBY/ON

Switches the system on or into standby.

2Function select buttons

Selects the source you want to listen to (DVD/ CD, TUNER, USB, LINE).

3Number buttons / CLEAR / DISPLAY CLEAR – Clears an entry.

DISPLAY – Displays/changes disc information shown on-screen (page 22).

En

Controls and displays

01

4TOP MENU – Displays the top menu of a DVD disc in the play position—this may be the same as pressing MENU (page 12).

SHIFT+SETUP – Use to make various system and surround sound settings (page 12, 13, 25, 34 and 35).

5Cursor, ENTER and tuning buttons

/ / / – Use the cursor buttons to navigate on-screen displays and menus.

ENTER – Selects an option or executes a command.

TUNE +/ñ – Tunes the radio.

ST +/ñ – Selects station presets when listening to the radio.

6HOME MENU – Displays (or exits) the onscreen menu for Initial Settings, Play Mode functions, etc.

SHIFT+MCACC – Starts the Auto MCACC setup (page 9).

7Sound controls

SOUND RETRIEVER – Press to restore CD quality sound to compressed audio sources (page 16).

SURROUND – Selects a Surround mode (page 14) or switches to stereo playback (page 15).

ADVANCED – Selects a Pioneer original surround mode (page 15) .

SOUND – Accesses the sound menu to adjust the tone, bass and treble, etc. (page 14 to 16).

8Playback controls

See Basic playback controls on page 11, Disc playback features on page 17 and USB playback on page 23 for an explanation of these controls.

9TV CONTROL buttons

These control Pioneer plasma displays.

10 SHIFT

Press to access the controls highlighted in green.

11OPEN/CLOSE

Opens/closes the disc tray.

12DVD controls

AUDIO – Selects audio channel/language (page 21).

SUBTITLE – Displays/changes the subtitles (page 21).

ANGLE – Changes camera angle during DVD multi-angle scene playback (page 22).

ZOOM – Changes the screen zoom level (page 22).

13MENU – Press to display a DVD disc or USB menu, or the Navigator (page 18 and 24).

SHIFT+SR+ – Switches the SR+ mode on/ off (page 33).

14RETURN – Returns to a previous menu screen.

SHIFT+TEST TONE – Outputs the test tone (for speaker setup) (page 25).

15SLEEP

Press to set the sleep timer (page 35).

16 MUTE

Mutes the sound (press again to cancel).

17 VOLUME +/ñ

Adjusts the volume.

EspaÒol Nederlands Italiano FranÁais Deutsch English

7

En

01 Controls and displays

Display

1

2

3

4

5

6

PRGSVE SOUND DTS F.SURR.

2D

2PL

14

13

12 11

10

1DTS

Lights during playback of a DTS source (page 14).

2PRGSVE

Lights when progressive scan video output is selected (page 27).

3SOUND

Lights when the Sound Retriever is active (page 15).

4SURR.

Lights when one of the Advanced surround listening modes is selected (page 15).

F.SURR.

Lights when one of the Front Surround listening mode is selected (page 15).

5RPT and RPT-1

RPT lights during repeat play. RPT-1 lights during repeat one-track play (page 19).

6PGM

Lights during program play (page 20).

7Tuner indicators

RPT -1

kHz PGM

MHz RDM

9

8

7

9kHz / MHz

Indicates the frequency unit shown in the character display (kHz for AM, MHz for FM).

10Character display

11

Lights when sleep timer is active (page 35).

12

Lights during playback.

13 2 PL II

Lights during Dolby Pro Logic II decoding (page 14).

14 2 D

Lights during playback of a Dolby Digital source (page 14).

– Lights when a broadcast is being received.

– Lights when a stereo FM broadcast is being received in auto stereo mode.

– Lights when FM mono reception is selected.

8RDM

Lights during random play (page 20).

8

En

Getting started

Chapter 2

Getting started

Home theater sound setup

Place your speakers as shown below for optimal surround sound (see the Speaker Setup Guide for more placement tips).

Standard surround 5-spot setup – This is a standard multichannel surround sound speaker setup for optimal 5.1 channel home theater sound.

Front left

Center

Front right

 

Subwoofer

Listening position

 

Surround

 

Surround

left

 

right

Depending on the size and characteristics of your room, you can choose to use the following

setup option:1

Front surround 3-spot setup – This setup is ideal when rear surround speaker placement isn't possible or you want to avoid running long speaker cables in your listening area. Use this setup together with the Front Surround modes to take advantage of wall and ceiling reflections for a very realistic surround effect.

Front left

Center

Front right

 

Subwoofer

Surround

 

Surround

left

 

right

Listening position

02

 

English

 

 

After placing your speakers, see Using the

 

Auto MCACC setup for optimal surround sound

Deutsch

below to complete your surround setup.

 

Using the Auto MCACC setup for optimal surround sound

The Multichannel Acoustic Calibration

 

 

FranÁais

 

 

 

(MCACC) system measures the acoustic

 

 

characteristics of your listening area, taking

 

into account ambient noise and testing for

 

channel delay and channel level. After you

 

have set up the microphone provided with your

Italiano

system, the receiver uses the information from

 

a series of test tones to optimize the speaker

 

settings and equalization (Acoustic Calibration

 

EQ) for your particular room.2

 

 

Nederlands

 

 

Important

 

 

 

 

 

 

 

 

 

 

 

 

 

• These test tones are loud; however, do not

 

turn the volume down during setup as this

 

may result in a sub-optimal calibration.

 

• Make sure the mic and speakers are not

EspaÒol

 

 

 

 

 

0

 

TV CONTROL

 

SLEEP

moved during the MCACC setup.

 

 

 

 

 

 

 

CLEAR

 

DISPLAY

ZOOM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TOPMENU

TUNE

 

MENU

 

 

 

STANDBY

 

TUNER

 

 

 

 

INPUT CHANNEL

VOLUME

MUTE

 

/ON

DVD/CD (FM/AM)

 

SETUP

 

 

SR

 

 

 

 

 

 

OPEN/

 

 

 

SHIFT

VOLUME

 

 

 

USB

LINE

CLOSE

ST

ENTER ST

 

 

 

 

 

HOME

 

 

 

 

 

 

 

 

 

 

MENU

 

 

RETURN

 

 

 

 

 

 

AUDIO

 

 

 

 

 

 

 

1

2

3

 

MCACC

TUNE

 

TEST TONE

 

 

 

 

 

 

SUBTITLE

SOUND

 

 

 

 

 

 

 

 

 

RETRIEVER SURROUND

ADVANCED SOUND

 

 

 

4

5

6

 

 

 

 

 

 

 

 

 

 

 

ANGLE

 

 

 

 

 

 

 

7

8

9

 

 

 

 

 

 

 

 

ZOOM

Note

1See Using Front Surround on page 15 to select a front surround mode when using this setup.

2You only need to use the Auto MCACC setup once (unless you change the placement of your speakers or your room layout).

9

En

02 Getting started

1 Connect the microphone to the MCACC MIC jack on the rear panel.

 

 

COMPONENT

R

 

 

VIDEO

 

 

VIDEO

 

CB/

 

 

PB

 

FM

 

 

AM LOOP

UNBAL75Ω

 

 

 

IN

 

 

 

S-VIDEO

 

Y

MCACC

 

VIDEO OUT

 

MIC

CONTROL

 

2 Place the microphone at your normal listening position.

Place it about ear height, and make sure it is level by using a table or chair.

Make sure there are no obstacles between the speakers and the microphone.

3 If the system is off, press STANDBY/ON to turn the power on.

If the tuner is selected, switch the input source.

4Press SHIFT+MCACC.

Try to be as quiet as possible after pressing SHIFT+MCACC. The volume increases automatically and the system outputs a series of test tones.

Press SHIFT+MCACC to cancel and revert to the previous Auto MCACC settings.

If the noise level is too high, NOISY blinks in the display for five seconds. To exit and check the noise levels1, press SHIFT+MCACC, or to try again, press ENTER when RETRY shows in the display.

When the MCACC setup is complete, the volume level returns to normal and

COMPLETE3 shows in the display, indicating that the MCACC setup is complete and

Acoustic Calibration EQ has been activated.4

Using the on-screen displays

For ease of use, this system makes extensive use of graphical on-screen displays (OSDs).

All the screens are navigated in basically the same way, using , , , to change the highlighted item and pressing ENTER to select

it.5

Important

Throughout this manual, ‘Select’ means use the cursor buttons to highlight an item on-screen, then press ENTER.

Button What it does

HOME Displays/exits the on-screen display

MENU

Changes the highlighted menu item

ENTER Selects the highlighted menu item

RETURN Returns to the main menu without saving changes

If you see an ERR MIC or ERR SP message in the display, there may be a problem with your mic or the speaker connections. To try again, press ENTER when you see RETRY2.

Tip

The button guide at the bottom of every OSD screen shows you which buttons you’ll need to use for that screen.

Note

1• If the room environment is not optimal for the Auto MCACC setup (too much ambient noise, echo off the walls, obstacles blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air conditioner, fridge, fan, etc.), that may be affecting the environment and switch them off if necessary.

Some older TVs may interfere with the operation of the mic. If this seems to be happening, switch off the TV during the Auto MCACC setup.

2If this doesn’t work, press SHIFT+MCACC, turn off the power, and check the problem indicated by the ERR message, then try the Auto MCACC setup again.

3If COMPLETE doesn’t appear, it is likely an error occurred during the setup. Please check all connections and try again.

4See Listening with Acoustic Calibration EQ on page 15 to switch on/off Acoustic Calibration EQ.

5The screen saver will appear after five minutes of inactivity.

10

En

Getting started

02

Playing discs

The basic playback controls for playing DVD, CD, Video CD/Super VCD, DivX video and WMA/MP3/MPEG-4 AAC discs are covered here. Further functions are detailed in chapter 4.

1 If the player isnít already on, switch it on.

If you’re playing a disc with video, also turn on your TV and make sure that it is set to the correct video input.

2 Press OPEN/CLOSE to load a disc.

Load a disc with the label side facing up, using the disc tray guide to align the disc (if you’re loading a double-sided DVD disc, load it with the side you want to play face down).

3 Press (play) to start playback.

If you’re playing a DVD or Video CD/Super VCD, a menu may appear. See DVD-Video disc menus and Video CD/Super VCD PBC menus on page 12 to navigate these.

If you loaded a disc containing JPEGs, a slideshow will start. See Playing a JPEG slideshow on page 17 for more on this.

If a disc contains a mixture of DivX video and other media file types (MP3, for example), first select whether to play the DivX video files (DivX) or the other media file types (MP3 / WMA / JPEG / MPEG-4 AAC) from the on-screen display.

4 Adjust the volume.

Use the VOLUME control.

Basic playback controls

The following table shows the basic controls on

the remote for playing discs1. You can find other playback features in the chapter 4.

Button What it does

Starts/resumes normal playback.

If the display shows RESUME or LAST MEM playback starts from the resume or last memory point (see

Resume and Last Memory below).

Pauses/unpauses a disc.

Stops playback or cancels the resume function (if the display shows RESUME).

Press to start fast reverse scanning.

Press to start fast forward scanning.

Skips to the start of the current track or chapter, then previous tracks/chapters.

Skips to the next track or chapter.

Numbers Use to enter a title/chapter/track number. Press ENTER to select.

If the disc is stopped, playback starts from the selected title (for DVD) or track (for CD/Video CD/Super VCD).

If the disc is playing, playback jumps to the start of the selected title (VR mode DVD-RW), chapter (DVD-Video) or track (CD/Video CD/Super VCD).

Resume and Last Memory

When you stop playback of a disc, RESUME shows in the display indicating that you can resume playback from that point.

With DVDs and Video CD/Super VCDs, even if

ejected, the play position is stored in memory.2 The next time you load the disc, the display shows LAST MEM and you can resume playback.

EspaÒol Nederlands Italiano FranÁais Deutsch English

Note

1You may find with some DVD discs that some playback controls don’t work in certain parts of the disc.

2• The Last Memory function may not work with some discs.

• For DVD-Video discs (except VR mode DVD-R/RW), the player stores the play position of the last five discs.

11

En

02 Getting started

If you want to clear the resume point, press (stop) while RESUME is displayed.

DVD-Video disc menus

Many DVD-Video discs contain menus from which you can select what you want to watch.

Sometimes DVD-Video menus are displayed automatically when you start playback; others only appear when you press MENU or TOP MENU.

Button

What it does

TOP MENU Displays the ‘top menu’ of a DVD disc—this varies with the disc.

MENU Displays a DVD disc menu—this varies with the disc and may be the same as the ‘top menu’.

Moves the cursor around the screen.

ENTER Selects the current menu option.

RETURN Returns to the previously displayed menu screen.

Numbers Highlights a numbered menu option (some discs only). Press ENTER to select.

Video CD/Super VCD PBC menus

Some Video CD/Super VCDs have menus from which you can choose what you want to watch. These are PBC (Playback control) menus.

You can play a PBC Video CD/Super VCD without having to navigate the PBC menu by starting playback using a number button to select a track, rather than the (play) button.

Button

What it does

RETURN

Displays the PBC menu.

 

 

Numbers

Selects numbered menu options.

 

Press ENTER to select.

 

 

 

Displays the previous menu page

 

(if there is one).

 

 

12

Button

What it does

Displays the next menu page (if there is one).

Listening to the radio

The tuner can receive both FM and AM broadcasts, and lets you memorize your favorite stations so you don’t have to manually tune in every time you want to listen.

1 Press TUNER to switch to the tuner, then press repeatedly to select the AM or FM band.

The display shows the band and frequency.

2Tune to a frequency.

There are three tuning modes—manual, auto, and high-speed:

Manual tuning: Press TUNE +/ñ repeatedly to change the displayed frequency.

Auto tuning: Press and hold TUNE +/ñ until the frequency display starts to move, then release. The tuner will stop on the next station it finds. Repeat to keep searching.

High-speed tuning: Press and hold TUNE +/ñ until the frequency display starts to move rapidly. Keep the button held down until you reach the frequency you want. If necessary, fine tune the frequency using the manual tuning method.

Improving poor FM reception

If you’re listening to an FM station in stereo but the reception is weak, you can improve the sound quality by switching to mono.

1 Tune to an FM radio station then press SHIFT+SETUP.

2 Use /to choose FM MODE then press

ENTER.

3 Use / to select FM MONO then press

ENTER.

The mono indicator ( ) lights when the tuner is in mono reception mode.

En

Getting started

Select FM AUTO above to switch back to autostereo mode (the stereo indicator () lights when receiving a stereo broadcast).

Reducing AM reception noise

If AM reception seems particularly poor, or the AM radio station you’re listening to seems noisy, try using the Noise Cut feature for better sound quality.

1 Tune to an AM radio station then press SHIFT+SETUP.

2 Use /to choose NOISECUT then press

ENTER.

3 Use /to select the noise cut mode then press ENTER.

Select an effect level between 1 and 3.

Memorizing stations

You can save up to 30 station presets so that you always have easy access to your favorite stations without having to tune in manually each time.

1 Tune to an AM or FM radio station.

Select mono or auto-stereo reception (FM) or the Noise Cut mode (AM) as necessary. These settings are saved along with the preset.

2 Press SHIFT+SETUP and use / to choose ëST.MEM.í then press ENTER.

3 Use / to select the station preset you want then press ENTER.

Listening to station presets

1Make sure the TUNER function is selected.

2 Use the ST +/ñ buttons to select a station preset.

You can also use the number buttons to do this.

Listening to other sources

You can connect auxiliary sources (TV, satellite receiver, etc.) to this unit for playback through the speaker system. See Connecting auxiliary audio components on page 31 for more on this.

To connect a USB device to the USB terminal, see USB playback on page 23.

1 Make sure that the external source (TV, satellite receiver, etc.) is switched on.

2Press LINE to select the source.

3If necessary, start playback of the source.

02

EspaÒol Nederlands Italiano FranÁais Deutsch English

13

En

03 Listening to your system

Chapter 3

Listening to your system

Auto listening mode

The Auto listening mode is the simplest way to listen to any source as it was mastered: the output from the speakers mirrors the channels in the source material.

See Using Front Surround below to get the best results from a Front surround 3-spot setup (page 9).

TUNE

TEST TONE

SOUND

RETRIEVER SURROUND ADVANCED SOUND

Press SURROUND to select the AUTO listening mode.1

Listening in surround sound

MOVIE (Dolby Pro Logic II Movie) – Pro Logic II 5.1 channel surround sound, especially suited to movie sources (use with any two-channel source)

MUSIC (Dolby Pro Logic II Music) – Pro Logic II 5.1 channel surround sound, especially suited to music sources (use with any two-channel source)

STEREO – See Listening in stereo below

Dolby Pro Logic II Music settings

When listening in Dolby Pro Logic II Music mode, there are three settings you can adjust: Center Width, Dimension, and Panorama.

1 With Dolby Pro Logic II Music mode active, press SOUND.

You can listen to stereo or multichannel

sources in surround sound.2 Surround sound is generated from stereo sources using one of the Dolby Pro Logic decoding modes.

See Using Front Surround below to get the best results from a Front surround 3-spot setup (page 9).

TUNE

TEST TONE

SOUND

RETRIEVER SURROUND ADVANCED SOUND

Press SURROUND repeatedly to select a

listening mode.1

The choices that appear in the display will vary according to the type of source that’s playing.

AUTO – Auto listening mode (see above)

DOLBY PL (Dolby Pro Logic) – 4.1 channel surround sound (use with any two-channel source)

2 Use /to select ëC WIDTHí, ëDIMEN.í or

ëPANORAMAí then press ENTER to confirm.

C WIDTH (Center Width): Provides a better blend of the front speakers by spreading the center channel between the front right and left speakers, making it sound wider (higher settings) or narrower (lower settings).

DIMEN. (Dimension): Adjusts the depth of the surround sound balance from front to back, making the sound more distant (minus settings), or more forward (positive settings).

PANORAMA – Extends the front stereo image to include the surround speakers for a ‘wraparound' effect.

Note

1If the source is Dolby Digital or DTS, the corresponding indicator lights in the front panel display.

2Note that when the tuner is selected, multichannel playback is not possible.

14

En

Listening to your system

Using Front Surround

The Front Surround mode is effective when you are using the Front surround 3-spot speaker setup as described in Home theater sound setup on page 9. The surround speakers should be placed beside the front speakers and oriented either towards the walls, or straight ahead, depending on which mode you are using (see below).

TUNE

TEST TONE

SOUND

RETRIEVER SURROUND ADVANCED SOUND

Press ADVANCED to select a Front Surround mode.

Press repeatedly to select FRTMOVIE,

FRTMUSIC or EXTPOWER.1

If you have selected FRTMOVIE (Front Surround Movie) or FRTMUSIC (Front Surround Music), turn each surround speaker so that the guide markers on the stand base are lined up horizontally in the direction the listening position (see below). With EXTPOWER (Extra Power), the surround speakers should be oriented in the same direction as the front speakers.

Front Music / Front Movie

Extra Power

03

• See Using Front Surround above to get the

English

best results from a Front surround 3-spot

 

setup (page 9).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TUNE

TEST TONE

 

 

SOUND

 

 

 

 

 

 

 

 

RETRIEVER SURROUND ADVANCED

SOUND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press ADVANCED to select an Advanced

 

Deutsch

ADVMUSIC, EXPANDED, TV SURR., SPORTS,

 

Surround mode.

 

 

 

 

 

 

 

Press repeatedly to select ADVMOVIE,

 

 

GAME, VIRTUAL or 5 STEREO.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FranÁais

Listening in stereo

 

 

 

 

 

 

 

 

 

 

 

 

 

You can listen to any source—stereo or

 

multichannel—in stereo. When playing a

 

multichannel source, all channels are

 

downmixed to the front left/right speakers and

Italiano

the subwoofer.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TUNE

TEST TONE

 

 

SOUND

 

 

 

 

 

 

 

 

RETRIEVER SURROUND ADVANCED

SOUND

 

 

 

 

 

 

 

 

 

Press SURROUND repeatedly until

 

 

 

 

 

 

 

Nederlands

STEREO shows in the display.

 

 

 

 

 

 

 

 

 

 

Listening with headphones

 

 

 

 

When headphones are connected, only the

 

 

 

 

 

STEREO (default) and PHONES SURROUND

EspaÒol

 

 

 

 

 

 

 

 

(virtual surround sound for headphones) modes are available.

With headphones connected, press ADVANCED to select PHONES SURROUND or SURROUND to select STEREO.

Using Advanced Surround

The Advanced Surround effects can be used with any multichannel or stereo source for a

variety of additional surround sound effects.1

Listening with Acoustic Calibration EQ

You can listen to sources using the Acoustic Calibration Equalization set in Using the Auto MCACC setup for optimal surround sound on

page 9.2

Note

1Note that when the tuner is selected, multichannel playback is not possible.

2Acoustic Calibration EQ is not available when headphones are connected.

15

En

03 Listening to your system

1 Press SOUND and use / to select

MCACC EQ then press ENTER.

2 Use / to select EQ ON or EQ OFF then press ENTER to confirm.

If you select EQ OFF, equalization is set to off but speaker settings (channel delay and channel level) remain in effect.

EQ ON is selected automatically after the Auto MCACC setup is completed.

Using the Sound Retriever

When audio data is removed during the WMA/ MP3/MPEG-4 AAC compression process, sound quality often suffers from an uneven sound image. The Sound Retriever feature employs new DSP technology that helps bring CD quality sound back to compressed 2- channel audio by restoring sound pressure and smoothing jagged artifacts left over after compression.

While listening to a stereo source, press SOUND RETRIEVER to switch the sound retriever on or off.

1 Press SOUND and use / to select

TONE then press ENTER.

2 Use /to select the option you want to adjust and press ENTER.

The Bass/Treble, Quiet and Midnight features cannot be used at the same time.

Adjusting the bass and treble

Use the tone controls to adjust the bass and treble.

Use / to select BASS or TREBLE then use / to adjust the tone. Press ENTER to confirm.

Quiet and Midnight modes

The Quiet listening feature reduces excessive bass or treble in a sound source.

The Midnight listening feature allows you to hear effective surround sound of movies at low volume levels.

After pressing ENTER, the setting switches on/off.

To cancel the Quiet or Midnight listening modes, select BASS/TRE.

Enhancing dialog

The Dialog Enhancement feature is designed to make the dialog stand out from other background sounds in a TV or movie soundtrack.

1 Press SOUND and use / to select

DIALOGUE then press ENTER.

2 Use / to select the amount of dialog enhancement then press ENTER to confirm.

Select between OFF, MID or MAX.

Boosting the bass level

There are two bass modes you can use to enhance the bass in a source.1

1 Press SOUND and use / to select

BASSMODE then press ENTER.

2 Use / to adjust the sound then press

ENTER to confirm.

Select between OFF, MUSIC or CINEMA.

Using the Tone controls

You can change the tonal balance of the sound by using the tone control menu.

Note

1 The Bass Mode is not available when headphones are connected.

16

En

Disc playback features

Chapter 4

Disc playback features

Important

Many of the functions covered in this chapter apply to DVD discs, Video CDs/ Super VCDs, CDs, DivX video and WMA/ MP3/MPEG-4 AAC/JPEG discs, although the exact operation of some varies slightly with the kind of disc loaded.

Some DVDs restrict the use of some functions (random or repeat, for example) in some or all parts of the disc. This is not a malfunction.

When playing Video CD/Super VCDs, some of the functions are not available during PBC playback. If you want to use them, start the disc playing using a number button to select a track.

1

During playback, press

(pause).

2

Press and hold

or

until slow

motion playback starts.

 

 

Press repeatedly to change the slow motion speed (shown on-screen).

• To resume playback, press (play).2

Frame advance/frame reverse

You can advance or back up DVD discs frame- by-frame. With Video CD/Super VCDs and DivX video you can only use frame advance.

1

During playback, press

(pause).

2

Press

or

to reverse or

advance a frame at a time.

• To resume playback, press (play).2

Scanning discs

 

Playing a JPEG slideshow

You can fast-scan discs forward or backward at

various different speeds.1

After loading a disc containing JPEG pictures,

 

press to start a slideshow from the first

During playback, press

or

to start

scanning.

 

 

Press repeatedly to increase the scanning speed (shown on-screen).

• To resume playback, press (play).2

Playing in slow motion

You can play DVDs, Video CD/Super VCDs and DivX video at four different forward slow motion speeds. DVD discs can also be played in reverse slow motion.

folder/picture on the disc.3 The player displays the pictures in each folder in alphabetical order.

If the disc contains WMA/MP3/MPEG-4 AAC files, playback of the slideshow and audio files repeats. During audio playback,

you can still use the skip (

/

), scan

(

/

) and pause ( ) functions.

Pictures are automatically adjusted so that they fill as much of the screen as possible.

Note

1Only one speed is available for DivX video discs.

2• Depending on the disc, normal playback may automatically resume when a new chapter is reached on a DVD disc.

With Video CD/Super VCDs in PBC mode or a WMA/MP3/MPEG-4 AAC track, playback automatically resumes at the end or beginning of the track.

3• The time it takes for the player to load a file increases with large file sizes.

Discs can contain up to 299 folders and up to 648 folders and files combined.

04

EspaÒol Nederlands Italiano FranÁais Deutsch English

17

En

04 Disc playback features

While the slideshow is running:

Button

What it does

 

Pauses the slideshow (or audio);

 

press again to restart.

 

 

 

Jumps to the previous picture (or

 

audio file with audio playback).

 

 

 

Jumps to the next picture (or

 

audio file with audio playback).

/ / / Pauses the slideshow and rotates/flips the displayed picture (Press (play) to restart slideshow).

ZOOM Pauses the slideshow and zooms the picture. Press again to toggle between 1x, 2x and 4x zoom (Press (play) to restart slideshow).

MENU Displays the Disc Navigator

screen (see below).

Browsing DVD or Video CD/ Super VCD discs with the Disc Navigator

Use the Disc Navigator to browse through the contents of a DVD or Video CD/Super VCD disc to find the part you want to play.

1 During playback, press HOME MENU and select ëDisc Navigatorí from the onscreen menu.

Disc Navigator

2Select a view option.

Disc Navigator

Title

Chapter

The options available depend on the kind of disc loaded and whether the disc is playing or not, but include:

Title – Titles from a DVD-Video disc.

Chapter – Chapters from the current title of a DVD-Video disc.

Track – Tracks from a Video CD/Super VCD disc.

Time – Thumbnails from a Video CD/Super VCD disc at 10 minute intervals.

Original: Title – Original titles from a VR mode DVD-RW disc.

Playlist: Title – Playlist titles from a VR mode DVD-RW disc.

Original: Time – Thumbnails from the Original content at 10 minute intervals.

Playlist: Time – Thumbnails from the Playlist at 10 minute intervals.

The screen shows up to six moving thumbnail images displayed one after another. To display the previous/next six thumbnails, press /

.

3 Select the thumbnail image for what you want to play.

01

02

03

04

05

06

Disc Navigator: Title 0149: --

You can use either / / / and ENTER to select a thumbnail, or the number buttons.

To select using the number buttons, enter a two-digit number then press ENTER.

18

En

Disc playback features

Browsing WMA, MP3, MPEG-4 AAC, DivX video and JPEG files with the Disc Navigator

Use the Disc Navigator to find a particular file or folder by filename.

1 Press HOME MENU and select ëDisc Navigatorí from the on-screen menu.

00:00/ 00:00

0kbps

Folder1

Folder2

Folder3

Folder4

2 Use / / / and ENTER to navigate.

Use / to move up and down the folder/file list.

Use to return to the parent folder.1

Use ENTER or to open a highlighted folder.

When a JPEG file is highlighted, a thumbnail image is displayed on the right.

00:00/ 00:00

0kbps

Folder2

File1

File2

File3

File4

File5

3 To play the highlighted track or DivX video file or display the highlighted JPEG file, press ENTER.

When a WMA/MP3/MPEG-4 AAC or DivX video file is selected, playback begins from that file, and continues until the end of the folder.

When a JPEG file is selected, a slideshow begins, starting with that file, and continues to the end of the folder.

04

 

 

Tip

English

• You can also play a JPEG slideshow while

 

listening to WMA/MP3/MPEG-4 AAC

 

playback. Simply select the audio file you

 

 

 

want to listen to followed by the JPEG from

 

 

 

which you want the slideshow to start.

 

Deutsch

 

effective for the JPEG slideshow only.

 

 

Playback of both the slideshow and the

 

 

 

audio files repeats. Playback controls are

 

 

• To play the contents of the whole disc

 

 

 

 

 

rather than just the current folder, exit the

FranÁais

 

Disc Navigator and start playback using

 

 

 

the (play) button.

 

Looping a section of a disc

The A-B Repeat function allows you to specify

 

Italiano

two points (A and B) within a track (CD, Video

 

 

 

CD/Super Video CD) or title (DVD) that form a

 

 

loop which is played over and over.

 

 

1

During playback, press HOME MENU and

 

 

 

 

select ëPlay Modeí.

 

Nederlands

 

 

 

 

 

 

 

 

 

 

Play Mode

 

 

 

 

 

 

 

 

 

2

Select ëA-B Repeatí.

 

 

 

 

3

Press ENTER on ëA(Start Point)í to set the

 

 

 

EspaÒol

loop start point.

 

 

 

4

Press ENTER on ëB(End Point)í to set the

 

 

loop end point.

 

 

After pressing ENTER, playback jumps back to the start point and plays the loop.

5To resume normal playback, select ëOffí.

Using repeat play

In addition to various repeat play options, it’s also possible to use repeat play together with program play (see Creating a program list on page 20).

Note

1 You can also do this by going to the ‘..’ folder at the top, then pressing ENTER.

19

En

04 Disc playback features

1 During playback, press HOME MENU and select ëPlay Modeí.

2Select ëRepeatí then select a repeat play

option.1

If program play is active, select Program Repeat to repeat the program list, or Repeat Off to cancel.

For DVD discs, select Title Repeat or

Chapter Repeat.

For CDs and Video CD/Super VCDs, select

Disc Repeat or Track Repeat.

For DivX video discs, select Title Repeat

(or Repeat Off).

Using random play

Use this function to play titles or chapters (DVD-Video) or tracks (CD and Video CD/Super

VCD) in a random order.2

1 During playback, press HOME MENU and select ëPlay Modeí.

2Select ëRandomí then select an option.

For DVD discs, select Random Title or

Random Chapter.

For CDs and Video CD/Super VCDs, select On or Off to switch random play on or off.

Button

What it does

Returns to the beginning of the current track/title/chapter; further presses select another random track/title/chapter.

Random play remains in effect until you select Random Off from the random play menu options.

Creating a program list

This feature lets you program the play order of titles/chapters/tracks on a disc.3

1 During playback, press HOME MENU and select ëPlay Modeí.

2 Select ëProgramí then select ëCreate/Edití from the list of program options.

3 Use / / / and ENTER to select a title, chapter or track for the current step in the program list.

For a DVD disc, you can add a title or a chapter.

For a CD or Video CD/Super VCD, select a track to add to the program list.

After pressing ENTER to select the title/ chapter/track, the step number automatically moves down one.

Tip

Use the following controls during random play:

Button

What it does

Selects a new track/title/chapter at random.

4 Repeat step 3 to build up a program list.

A program list can contain up to 24 steps.

You can insert steps by just highlighting the position where you want the new step to appear and entering a title/chapter/track number.

To delete a step, highlight it and press

CLEAR.

Note

1You can’t use repeat play with WMA/MP3/MPEG-4 AAC discs.

2• You can set the random play option when a disc is playing or stopped. However, you can't use random play together with program play.

You can’t use random play with VR format DVD-R/RW discs, WMA/MP3/MPEG-4 AAC discs, DivX video discs, or while a DVD disc menu is being displayed.

3You can’t use Program play with VR format DVD-R/RW discs, WMA/MP3/MPEG-4 AAC discs, DivX video discs, or while a DVD disc menu is being displayed.

20

En

Disc playback features

04

5 To play the program list, press (play).

Program play remains active until you turn off program play (see below), erase the program list (see below), eject the disc or switch off.

Tip

Use the following controls during program play:

Button

What it does

HOME Save the program list and exit MENU without starting playback.

Skip to the next step in the program list.

3Select a search mode.

The disc must be playing in order to use time search.

4 Use the number buttons to enter a title, chapter or track number, or a time.

For a time search, enter the number of minutes and seconds into the currently playing title (DVD/ DivX video) or track (CD/ Video CD/Super VCD) you want playback to resume from. For example, press 4, 5, 0, 0 to have playback start from 45 minutes into the disc. For 1 hour, 20 minutes and 30 seconds, press 8, 0, 3, 0.

5Press ENTER to start playback.

Other functions available from the program menu

There are a number of other options in the program menu in addition to Create/Edit.

Playback Start – Starts playback of a saved program list

Playback Stop – Turns off program play, but does not erase the program list

Program Delete – Erases the program list and turns off program play

Searching a disc

Switching subtitles

Some DVD discs and DivX video discs have subtitles in one or more languages; the disc box will usually tell you which subtitle languages are available. You can switch

subtitle language during playback.1

Press SUBTITLE repeatedly to select a subtitle option.

To set subtitle preferences, see Language settings on page 27.

See Displaying DivX subtitle files on page 37 for more on DivX subtitles.

You can search DVD discs by title or chapter number, or by time; CDs and Video CD/Super VCDs by track number or time; DivX video discs by time.

1 Press HOME MENU and select ëPlay Modeí.

2Select ëSearch Modeí.

The search options that appear depend on the kind of disc loaded.

Switching language / audio channels

When playing discs recorded with dialog in two or more languages, or with dual-mono audio2 you can switch these during playback.3

Press AUDIO repeatedly to select an audio language option.

To set audio language preferences, see

Language settings on page 27.

Note

1Some discs only allow you to change subtitle language from the disc menu. Press TOP MENU or MENU to access.

2Some Super VCDs have two soundtracks. With these discs you can switch between the two soundtracks as well as individual channels in each.

3Some discs only allow you to change audio language from the disc menu. Press TOP MENU or MENU to access.

EspaÒol Nederlands Italiano FranÁais Deutsch English

21

En

04 Disc playback features

Zooming the screen

Using the zoom feature you can magnify a part of the screen by a factor of 2 or 4, while watching a DVD, DivX video title or Video CD/ Super VCD or playing a JPEG disc.

1 During playback, use the ZOOM button to select the zoom factor (Normal, 2x or 4x).

2 Use / / / to change the zoomed area.

You can change the zoom factor and the zoomed area freely during playback.1

Switching camera angles

Some DVD discs feature scenes shot from two or more angles—check the disc box for details.

When a multi-angle scene is playing, a icon appears on screen (this can be switched off if you prefer—see Display settings on page 28).

During playback (or when paused), press ANGLE to switch angle.

Displaying disc information

Various track, chapter and title information can be displayed on-screen during playback.

To show/switch/hide the information displayed, press DISPLAY repeatedly.

Limited disc information also appears in the front panel display. Press DISPLAY to change the displayed information.

Note

1 • Since DVD, Video CD/Super VCD, DivX video title and JPEG pictures have a fixed resolution, picture quality will deteriorate, especially at 4x zoom. This is not a malfunction.

• If the navigation square at the top of the screen disappears, press ZOOM again to display it.

22

En

USB playback

Chapter 5

USB playback

Using the USB interface

It is possible to listen to two-channel audio1 and watch JPEG files using the USB interface on the front of this unit. Connect a USB mass

storage device2 as shown below.

1 With the player switched on, press USB.

Make sure your TV is on and set to the correct video input.

2Connect your USB device.

The USB terminal is located on the front panel.

USB

Type A

USB mass storage device

Important

If a USB ERR message lights in the display, it may mean that the power requirements of the USB device are too high for this player, or that the device is incompatible. Try the following:

Switch the player off, then on again.

Reconnecting the USB device with the player switched off.

Selecting to another input source (like DVD/CD), then back to USB.

Using a dedicated AC adapter (supplied with the device) for USB power.

If this doesn’t remedy the problem, it is likely your USB device is incompatible.

Basic playback controls

The following table shows the basic controls on the remote for USB playback.

Button What it does

Starts normal playback.

Pauses/unpauses playback.

Stops playback.

3 Press (play) to start playback.

If your USB device contains JPEGs, a slideshow will start. See Playing a JPEG slideshow on page 24 for more on this.

Make sure USB DATA is showing in the front panel display (or the system is in standby) when disconnecting.

Press to start fast reverse scanning.

Press to start fast forward scanning.

Skips to the start of the current file, then previous files.

Skips to the next file.

Note

1This includes playback of WMA/MP3/MPEG-4 AAC files (except files with copy-protection or restricted playback). It is not possible to play DivX files through the USB terminal.

2• Compatible USB devices include external magnetic hard drives, portable flash memory (particularly keydrives) and digital audio players (MP3 players) of format FAT16/32. It is not possible to connect this unit to a personal computer for USB playback.

Pioneer cannot guarantee compatibility (operation and/or bus power) with all USB mass storage devices and assumes no responsibility for any loss of data that may occur when connected to this unit.

With large amounts of data, it may take longer for the system to read the contents of a USB device.

05

EspaÒol Nederlands Italiano FranÁais Deutsch English

23

En

05 USB playback

Scanning files

You can fast-scan forward or backward at various different speeds.

During playback, press

or

.

Press repeatedly to increase the scanning speed (shown on-screen).

• To resume playback, press (play).1

Button

What it does

MENU Displays the Navigator screen (see below).

Browsing files with the Navigator

Use the Navigator to find WMA, MP3, MPEG-4 AAC and JPEG files or folders by name.3

Playing a JPEG slideshow

Press to start a slideshow from the first

folder/picture.2 The pictures in each folder are displayed in order.

If the device contains WMA/MP3/MPEG-4 AAC files, playback of the slideshow and audio files repeats. During audio playback,

you can still use the skip (

/

), scan

(

/

) and pause ( ) functions.

Pictures are automatically adjusted so that they fill as much of the screen as possible.

While the slideshow is running:

Button

What it does

 

Pauses the slideshow (or audio);

 

press again to restart.

 

 

 

Jumps to the previous picture (or

 

audio file with audio playback).

 

 

 

Jumps to the next picture (or

 

audio file with audio playback).

 

/ / / Pauses the slideshow and

 

rotates/flips the current picture

 

(Press

to restart slideshow).

 

 

ZOOM

Pauses the slideshow and zooms

 

the picture. Press again to toggle

 

between 1x, 2x and 4x zoom

 

(Press

to restart slideshow).

 

 

 

1 Press MENU then use / / / and

ENTER to navigate.

Use / to move up/down the folder/file list. Use to return to the parent folder.4

Use ENTER or to open a highlighted folder.

When a JPEG file is highlighted, a thumbnail image is displayed on the right.

2 To play the highlighted track or display the highlighted JPEG file, press ENTER.

When a WMA/MP3/MPEG-4 AAC file is selected, playback begins from that file, and continues until the end of the folder.

When a JPEG file is selected, a slideshow begins, starting with that file, and continues to the end of the folder.

Tip

You can also play a JPEG slideshow while listening to WMA/MP3/MPEG-4 AAC playback. Simply select the audio file you want to listen to followed by the JPEG from which you want the slideshow to start. Playback of both the slideshow and the audio files repeats. Playback controls are effective for the JPEG slideshow only.

To play all of the contents, rather than just the current folder, exit the Navigator and

start playback using the (play) button.

Note

1With WMA/MP3/MPEG-4 AAC tracks, playback automatically resumes at the end or beginning of the track.

2• The time it takes for the player to load a file increases with large file sizes.

• USB devices can contain up to 299 folders and up to 648 folders and files combined.

3Filenames may be displayed incorrectly with some digital audio players.

4You can also do this by going to the ‘..’ folder at the top, then pressing ENTER.

24

En

Surround sound settings

Chapter 6

Surround sound settings

Using the Setup menu

From the Setup menu you can access all the

surround sound settings of the system1, including channel levels, speaker distances and dynamic range adjustment. The Auto MCACC feature (page 9) should give you the best surround sound setup. However you may find that by further adjustment of the surround sound settings you can improve the surround sound in your listening room.

1 Press SHIFT+SETUP and use / then

ENTER to choose the setting you want to adjust.

The available settings are shown in the front panel display.2

2 Use / to adjust then press ENTER to confirm and exit.

Note that using the Auto MCACC (page 9) again overwrites the speaker settings.

Channel level setting

Set the relative channel levels from your main listening position.3

Use / to switch between channels in the following order:

L – Front left speaker

C – Center speaker

R – Front right speaker

SR – Surround right speaker

SL – Surround left speaker

SW – Subwoofer

The channel level range is ± 10 dB.

Speaker distance setting

Specifies the distance from your listening position to your speakers.

When DISTANCE appears, press ENTER, then use / to adjust the distance, and / to switch between the following speakers:

L – Front left speaker

C – Center speaker

R – Front right speaker

SR – Surround right speaker

SL – Surround left speaker

SW – Subwoofer

Each speaker can be adjusted between 0.3 m and 9.0 m. The default setting is 3.0 m.

Dynamic Range Control

Specifies dynamic range adjustment to Dolby Digital or some DTS soundtracks. If low level sound or dialog seem difficult to hear properly, this can help by bringing up the low level sounds, while controlling high level peaks.

DRC OFF (default) – No dynamic range adjustment (use when listening at higher volumes)

DRC MID – Mid setting

DRC HIGH – Dynamic range is reduced (loud sounds are reduced in volume while quieter sounds are increased)

Note

1There are other settings you can adjust from the Setup menu; these are explained in Improving poor FM reception on page 12 and Dimming the display on page 35.

2The setup menu is exited automatically after 5 minutes of inactivity.

3• You can’t adjust center/surround when Stereo or Virtual playback is selected (or with stereo sources using the Auto mode).

The Channel level setting is not available when headphones are connected.

The speaker volume can be adjusted at any time by pressing SHIFT+TEST TONE and then using / to adjust the channel levels. The test tone automatically moves from speaker to speaker in the order listed above. You should hear the test tone at the same volume from each speaker when seated in the main listening position. Press ENTER when you’re finished.

Since the subwoofer produces ultra-low frequencies it may seem quieter than it actually is.

06

EspaÒol Nederlands Italiano FranÁais Deutsch English

25

En

07 Video Adjust menu

Chapter 7

Video Adjust menu

Video Adjust menu

From the Video Adjust screen you can adjust settings that affect picture presentation.

1 Press HOME MENU and select ëVideo Adjustí from the on-screen display.

Video Adjust

2 Make settings using / / / and

ENTER.

Video Adjust

 

Sharpness

Standard

Brightness

0

Contrast

0

Gamma

Off

Hue

0

Chroma Level

0

You can adjust the following settings:

Sharpness – Adjusts the sharpness of edges in the picture (Fine, Standard, Soft)

Brightness – Adjusts the overall brightness (ñ20 to +20)

Contrast – Adjusts the contrast between light and dark (ñ16 to +16)

Gamma – Adjusts the ‘warmth’ of the picture (High, Medium, Low, Off)

Hue – Adjusts the red/green balance (Green 9 to Red 9)

Chroma Level – Adjusts how saturated colors appear (ñ9 to +9)

Adjust the Brightness, Contrast, Hue and

Chroma Level settings using /.

Brightness

min

max

0

3 Press ENTER to return to the Video Adjust screen, or HOME MENU to exit.

26

En

Initial Settings menu

Chapter 8

Initial Settings menu

Using the Initial Settings menu

The Initial Settings menu provides audio and video output settings, parental lock settings, and display settings, among others.

If an option is grayed out it means that it cannot be changed at the current time. This is usually because a disc is playing. Stop the disc, then change the setting.

1Press DVD/CD.

2 With playback stopped, press HOME MENU and select ëInitial Settingsí.

Initial Settings

3 Use / / / and ENTER to select the setting and option you want to set.

All the settings and options are explained on the following pages.1

08

FranÁais Deutsch English

Video Output settings

Setting

Option

What it means

TV Screen

4:3 (Letter Box)

Set if you have a conventional 4:3 TV. Widescreen movies are

(See also Screen sizes

 

shown with black bars top and bottom.

and disc formats on

 

 

4:3 (Pan & Scan)

Set if you have a conventional 4:3 TV. Widescreen movies are

page 39.)

 

shown with the sides cropped so that the image fills the screen.

 

 

 

 

 

 

16:9 (Wide)

Set if you have a widescreen TV.

 

 

 

Component Out

Interlace

Set if your TV is not compatible with progressive scan video.

(See also Connecting

 

 

Progressive

Set if your TV is compatible with progressive scan video (see

using the component

 

your TV’s instruction manual for details). Press ENTER once

video output on

 

 

more to confirm (or RETURN to cancel).

page 32.)

 

 

Note that progressive scan video is only output from the

 

 

 

 

component video jacks.

 

 

 

Language settings

EspaÒol Nederlands Italiano

Setting

Option

What it means

Audio Language

English

If there is an English soundtrack on the disc, it is played.

 

 

 

 

Languages as displayed

If there is a language selected on the disc, it is played.

 

 

 

 

Other Language

Select to choose a language other than the ones displayed (see

 

 

Using the language code list on page 43).

 

 

 

Note

1• In the table, the default setting is shown in bold: other settings are shown in italics.

Some settings, such as TV Screen, Audio Language and Subtitle Language may be overridden by the DVD disc. Often these settings can also be made from the DVD disc menu.

27

En

08 Initial Settings menu

Setting

Option

What it means

Subtitle Language

English

If there are English subtitles on the disc they are displayed.

 

 

 

 

Languages as displayed

The subtitle language selected on the disc is displayed.

 

 

 

 

Other Language

Select to choose a language other than the ones displayed (see

 

 

Using the language code list on page 43).

 

 

 

DVD Menu

w/Subtitle Lang.

DVD disc menus are displayed in the same language as your

Language

 

selected subtitle language, if possible.

 

 

 

 

Languages as displayed

DVD menus are displayed in the selected language, if possible.

 

 

 

 

Other Language

Select to choose a language other than the ones displayed (see

 

 

Using the language code list on page 43).

 

 

 

Subtitle Display

On

Subtitles are displayed in your selected subtitle language.

 

 

 

 

Off

Subtitles are always off by default when you play a DVD disc.

 

 

 

 

 

 

Display settings

Setting

Option

What it means

 

OSD Language

English

On-screen displays of the player are in English.

 

 

 

 

 

 

Languages as displayed

On-screen displays are shown in the language selected.

 

 

 

 

 

Angle Indicator

On

A camera icon is displayed on-screen during multi-angle

 

 

 

scenes on a DVD disc.

 

 

 

 

 

 

Off

No multi-angle indication is shown.

 

 

 

 

 

 

 

 

 

Options settings

Setting

Option

What it means

Parental Lock

ñ

See Parental Lock below.

 

 

 

DivX(R) VOD

Display

See About DivX® VOD content below.

 

 

 

Parental Lock

Default level: Off; Default password: none; Default Country/Area code: us (2119)

To give you some control over what your children watch on your DVD player, some DVDVideo discs feature a Parental Lock level. If your player is set to a lower level than the disc, the disc won’t play.

Some discs also support the Country/Area Code feature. The player does not play certain scenes on these discs, depending on the Country/Area Code you set.

Registering a new password

Register a password to change the Parental Lock level or enter a Country/Area code.1

Note

1• Not all discs use Parental Lock, and will play without requiring the password first.

• If you forget your password, you’ll need to reset the player to register a new password (see Resetting the system on page 43).

28

En

Initial Settings menu

08

1Select ëPasswordí.

Initial Settings

 

 

Video Output

Parental Lock

Password

Language

DivX (R) VOD

Level Change

Display

 

Country Code

Options

 

 

2 Use the number buttons to input a 4-digit password then press ENTER.

Changing your password

To change your password, confirm your existing password then enter a new one.

1 Select ëPassword Changeí, input your existing password, then press ENTER.

2Enter a new password and press ENTER.

Setting/changing the Parental Lock

1Select ëLevel Changeí.

2 Use number buttons to enter your password, then press ENTER.

3Select a new level and press ENTER.

Press repeatedly to lock more levels

(more discs will require the password); press to unlock levels. You can’t lock level 1.

Setting/changing the Country/Area code

You can find the Country/Area code list on page 44.

1 Select ëCountry Codeí, input your password, then press ENTER.

2 Select a Country/Area code then press ENTER.

There are two ways you can do this:

Select by code letter: Use / to change the Country/Area code.

Select by code number: Press then use the number buttons to enter the 4-digit Country/Area code.

The new Country/Area code takes effect after ejecting the disc once.

About DivX® VOD content

In order to play DivX VOD (video on demand) content on this player, you first need to register the player with your DivX VOD content provider. You do this by generating a DivX VOD registration code, which you submit to your

provider.1

Important

DivX VOD content is protected by a DRM (Digital Rights Management) system. This restricts playback of content to specific, registered devices.

If you load a disc that contains DivX VOD content not authorized for your player, the message Authorization Error is displayed and the content will not play.

Displaying your DivX VOD registration code

1 Press HOME MENU and select ëInitial Settingsí.

2Select ëOptionsí, then ëDivX (R) VODí.

Initial Settings

 

 

Video Output

Parental Lock

Display

Language

DivX (R) VOD

 

Display

 

 

Options

 

 

3Select ëDisplayí.

Your 8-digit registration code is displayed.

Make a note of the code as you will need it when you register with a DivX VOD provider.

EspaÒol Nederlands Italiano FranÁais Deutsch English

Note

1 Resetting the player (as described in Resetting the system on page 43) will not cause you to lose your registration code.

29

En

08 Initial Settings menu

Playing DivX® VOD content

Some DivX VOD content may only be playable a fixed number of times. When you load a disc containing this type of DivX VOD content, the remaining number of plays is shown on-screen and you then have the option of playing the disc (thereby using up one of the remaining plays), or stopping. If you load a disc that contains expired DivX VOD content (for example, content that has zero remaining plays), the message Rental Expired is displayed.

If your DivX VOD content allows an unlimited number of plays, then you may load the disc into your player and play the content as often as you like, and no message will be displayed.

30

En

Other connections

Chapter 9

Other connections

Connecting external antennas

For an external AM antenna, use 5 m to 6 m of vinyl-insulated wire and set up either indoors or outdoors. Leave the loop antenna connected.

 

Outdoor antenna

Indoor

 

 

antenna

 

 

(vinyl-coated

 

 

wire)

5 m to 6 m

AM LOOP

 

 

For an external FM antenna, use a PAL connector to hook up an external FM antenna.

ANTENNA

PAL connector

Connecting auxiliary audio components

Using the stereo analog inputs, you can connect an external component such as a tape deck or MD player for playback through this system.

Connect the LINE AUDIO IN jacks to the analog outputs of an external playback component.

Connect using RCA pin-plug stereo cables.

Connecting the S-video output

If your TV has an S-video input, you can use this instead of the standard video output for a better quality picture.

Use an S-video cable to connect the S- VIDEO OUT to an S-video input on your TV.

Line up the small triangle above the jack with the same mark on the plug before plugging in.

 

 

 

S-VIDEO

 

 

 

INPUT

TV

 

 

 

ANTENNA

 

CR/

 

 

COMPONENT

PR

 

 

VIDEO

 

 

VIDEO

 

CB/

 

 

PB

 

FM

 

 

AM LOOP

UNBAL75Ω

 

 

 

IN

 

Y

 

S-VIDEO

 

MCACC

 

VIDEO OUT

 

MIC

CONTROL

 

09

EspaÒol Nederlands Italiano FranÁais Deutsch English

AUDIO Tape deck, etc.

OUTPUT

COMPONENT

LINE

FRONT R

VIDEO

CB/

 

L

PB

 

Y

R

SURROUND R

VIDEO OUT

AUDIO IN

S

31

En

09 Other connections

Connecting using the component video output

If your TV has component video inputs, you can use these instead of the standard video output

to connect this system to your TV.1 This should give you the best quality picture from the three types of video output available.

Compatibility of this player with progressive-scan and high-definition TVs

This player is compatible with progressive video Macro Vision System Copy Guard.2

Using this unit with a Pioneer plasma display

Use a component video cable to connect the COMPONENT VIDEO OUT to a set of component inputs on your TV.

 

 

 

COMPONENT

 

 

 

INPUT

TV

 

 

 

ANTENNA

 

CR/

 

 

COMPONENT

PR

 

 

VIDEO

 

 

VIDEO

 

CB/

 

 

PB

 

FM

 

 

AM LOOP

UNBAL75Ω

 

 

 

IN

 

 

 

S-VIDEO

 

Y

MCACC

 

VIDEO OUT

 

MIC

CONTROL

 

About progressive scan video

Compared to interlace video, progressive scan video effectively doubles the scanning rate of the picture, resulting in a very stable, flickerfree image. Progressive scan video is available only from the component video output.

If you have a Pioneer plasma display3, you can

use an SR+ cable4 to connect it to this unit and take advantage of various convenient features, such as controlling this unit via the plasma display's remote sensor, automatic video input switching of the plasma display, and automatic volume muting on the plasma display.

Media receiver

CONTROL

OUT

Pioneer plasma display

ANTENNA

 

CR/

 

COMPONENT

PR

 

VIDEO

 

VIDEO

 

CB/

 

PB

FM

 

 

AM LOOP

UNBAL75Ω

 

 

IN

Y

 

S-VIDEO

MCACC

 

VIDEO OUT

MIC

CONTROL

Note

1The component video output is switchable between interlaced and progressive formats. See Video Output settings on page 27.

2Consumers should note that not all high-definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 525 progressive scan picture problems, it is recommended that the user switch the connection to the ‘standard definition’ output (Interlace). If there are questions regarding our TV set compatibility with this model, please contact our customer service center.

3This system is compatible with all Pioneer plasma displays from 2003 onward.

4The 3-ringed SR+ cable from Pioneer is commercially available under the part number ADE7095. Contact the Pioneer Customer Support division for more information on obtaining an SR+ cable.

32

En

Other connections

09

Important

With an SR+ cable connected, the remote must now be pointed towards your plasma display rather than the remote sensor of this unit in order to control this system.

Use a 3-ringed miniplug SR+ cable to connect the CONTROL IN jack of this unit through a media receiver to the CONTROL

OUT jack of your plasma display.1

Before you can use the extra SR+ features, you need to make a few settings in the unit. See

SR+ Setup for Pioneer plasma displays below for detailed instructions.

SR+ Setup for Pioneer plasma displays

Make the following settings if you have connected a Pioneer plasma display to this unit using an SR+ cable. Note that the number of video inputs available will depend on the plasma display you’ve connected.

1Press SHIFT+SR+ on the remote.

2 Use the / to select SETUP, then press ENTER.

3Use / to select the setting you want.

VoL.C OFF – This unit does not control the volume of the plasma display.

VOL.C ON – When this unit is switched to one of the inputs that use the plasma display (DVD, or another one of functions below), the volume on the plasma display is muted so only sound from this system is heard.

4 Assign any input source connected to the plasma display to the corresponding input number.

Use / to select the source (DVD, LN (LINE) or USB), then / to select the input number.

This matches this unit’s input source with a

numbered video input on the plasma display.2 For example, select the LN PDP3 setting if the video output of your line component is connected to video input 3 on the plasma display. TVTN switches the plasma display to its built-in tuner and NONE leaves the plasma display input as is (no switching takes place).

5When you're finished, press ENTER.

Switching on the SR+ mode

1Press SHIFT+SR+ on the remote.

2 Use / to select SR+ ON then press

ENTER.

To switch SR+ control off, select SR+ OFF.

If you disconnect the SR+ cable or switch the plasma display off while SR+ is on, the SR+ ON setting remains.

The SR+ setting is maintained even after switching this system into standby then back on. Automatic muting will be effective when this system is switched on.

EspaÒol Nederlands Italiano FranÁais Deutsch English

Note

1You won’t be able to use the remote sensor of this unit with the CONTROL IN jack of this unit connected to the CONTROL OUT jack of your plasma display. You can use the remote sensor of the plasma display (even in standby) as long as the power isn’t switched off.

2The PDP5 input may be called ‘PC Input’ (or similar) on your plasma display.

33

En

10 Additional information

Chapter 10

Additional information

Optional system settings

All the available settings in the standby setup menu are listed below. See the notes in each section for more information about the settings. The first setting in each section is the default.

1Switch the system into standby.

2 Press SHIFT+SETUP and use / then

ENTER to choose the setting you want to adjust.

The available settings are shown in the front panel display.1

3 Use / to adjust then press ENTER to confirm and exit.

System demo setting

Switches the automatic demo feature on or off (this starts when you plug in for the first time):

DEMO ON – Switches the demo feature on.

DEMO OFF – Switches the demo feature off.

Frequency step setting

If you find that you can’t tune into stations successfully, the frequency step may not be suitable for your country/region.

AM 9K

AM 10K

TV system setting

The default setting of this system is AUTO, and unless you notice that the picture is distorted when playing some discs, you should leave it set to AUTO. If you find picture distortion with some discs, set the TV system to match your country or region’s system. However, this may restrict the kinds of disc you can watch. See the table for the kinds of discs compatible with

each setting (AUTO, PAL and NTSC).2

After using / to choose TV SYS (step

2 above), press ENTER to change the TV system as follows:

AUTO NTSC

NTSC PAL

PAL AUTO

The system automatically switches on and you’ll see the new TV system setting in the

display after seeing WELCOME.3

 

 

Player setting

Media Type

Format

NTSC

PAL

AUTO

 

 

 

 

 

DVD/Super VCD/

NTSC

NTSC

PAL

NTSC

Video CD/DivX

PAL

NTSC

PAL

PAL

Video

 

 

 

 

 

 

 

 

 

CD/MP3/WMA/

ó

NTSC

PAL

NTSC or

MPEG-4 AAC/

 

 

 

PAL

JPEG/no disc

 

 

 

 

 

 

 

 

 

DTS CD setting

If you play a DTS-encoded CD, you will need to change this setting to hear the decoded signal.

Note

1The setup menu is exited automatically after 5 minutes of inactivity.

2Most models of the newly developed countdown PAL TV system detect 50 Hz (PAL)/60 Hz (NTSC) and automatically switch vertical amplitude, resulting in a display without vertical shrinkage. However, in some cases, the image may appear without color. If your PAL TV does not have a V-Hold control, you may not be able to watch NTSC discs because of picture roll. If the TV has a V-Hold control, adjust it until the picture stops rolling. On some TVs, the picture may shrink vertically, leaving black bands at the top and bottom of the screen.

3 You have to switch the player into standby (press STANDBY/ON) before each change.

34

En

Additional information

NORMAL – Regular CD playback; some DTS-encoded CDs output a noisy signal.

DTS-CD – Proper decoding of DTSencoded CDs; the beginning of regular CD tracks my be skipped.

Key lock setting

LOCK ON – Makes the front panel buttons and controls inoperative.

LOCK OFF – Restores regular use of the front panel buttons and controls.

Setting the sleep timer

The sleep timer switches off the system after about an hour so you can fall asleep without

worrying about it.1

Press SLEEP repeatedly to select an option.

Choose between the following options:

SLP ON – Switches off after about an hour

SLP OFF – Cancels the sleep timer

After selecting SLP ON, you can press SLEEP again to check how much time is left. Each line indicates approximately 12 minutes (remaining):

S L P - - - - -

Dimming the display

You can choose one of two brightness settings for the front panel display.

1 Press SHIFT+SETUP and use / to select DIMMER then press ENTER.

2 Use / to adjust then press ENTER to confirm and exit.

LIGHT – Brighter setting

DARK – Darker setting

10

Disc / content format playback

English

compatibility

 

 

 

 

 

This player is compatible with a wide range of

 

disc types (media) and formats. Playable discs

 

will generally feature one of the following logos

Deutsch

on the disc and/or disc packaging. Note

 

however that some disc types, such as

 

recordable CD and DVD, may be in an

 

unplayable format.

 

 

 

See the Disc compatibility table below for more

 

information.

 

 

FranÁais

 

DVD-Video DVD-R

DVD-RW

 

 

 

Audio CD Video CD

CD-R

CD-RW

Italiano

 

 

 

Fujicolor CD

 

Nederlands

 

 

 

• This unit will play DVD+R/+RW discs.

 

is a trademark of Fuji Photo Film Co. Ltd.

EspaÒol

• Also compatible with KODAK Picture CD.

is a trademark of DVD Format/Logo

 

Licensing Corporation.

This player supports the IEC’s Super VCD standard for superior picture quality, dual soundtracks, and widescreen support.

VIDEO

CD

Super Video CD (Super VCD)

Note

1 The display dims when the sleep timer is set.

35

En

10 Additional information

About DualDisc playback

A DualDisc is a new two -sided disc, one side of which contains DVD content video, audio, etc. while the other side contains non-DVD content such as digital audio material.

The non-DVD, audio side of the disc is not compliant with the CD Audio specification and therefore may not play.

The DVD side of a DualDisc plays in this product. DVD-Audio content will not play.

For more detailed information on the DualDisc specification, please refer to the disc manufacturer or disc retailer.

Disc compatibility table

Media

Compatible formats

CD-R/RW • CD-Audio, Video CD/Super VCD, ISO 9660 CD-ROM*

* ISO 9660 Level 1 or 2 compliant. CD physical format: Mode1, Mode2 XA Form1. Romeo and Joliet file systems are both compatible.

Multi-session playback: No

Unfinalized disc playback: No

DVD-R/RW • DVD-Video (Video mode), Video Recording (VR)*, UDF Bridge DVD-ROM * Edit points may not play exactly as edited; screen may go momentarily blank at edited points.

Multi Border playback: No

Unfinalized playback: No

PC-created • Discs recorded using a PC may not disc be playable due to the setting of the

software used to create the disc. In these instances, check the DVD-R/RW or CD-R/RW software manual or disc boxes for more on compatibility.

• Discs recorded in packet write mode are not compatible.

36

Media

Compatible formats

Compressed • MPEG-1 Audio Layer 3 (MP3),

audio Windows Media Audio (WMA), MPEG- 4 AAC

Sampling rates: 32 kHz / 44.1 kHz / 48 kHz

Bit-rates: Any (128 kbps or higher recommended)

VBR (variable bit rate) MP3/WMA/ MPEG-4 AAC playback: No

WMA lossless encoding: No

DRM (Digital Rights Management) compatible: Yes (DRM-protected audio files will not play in this player).

File extensions: .mp3, .wma, .m4a (these must be used for the player to recognize MP3/WMA/MPEG-4 AAC files)

File structure (may differ): Up to 299 folders on a disc; up to 648 folders and files (combined) within each folder

JPEG file • Baseline JPEG and EXIF 2.2* still image files up to a resolution of 3072 x 2048.

*File format for digital still cameras

Progressive JPEG compatible: No

File extensions: .jpg (must be used for the player to recognize JPEG files)

File structure (may differ): Up to 299 folders on a disc; up to 648 folders and files (combined) within each folder

About DVD+R/DVD+RW compatibility

Only DVD+R/DVD+RW discs recorded in ‘Video Mode (DVD Video Mode)’ which have been finalized, can be played back. However, some editing made during the recording may not be played back accurately.

About DivX

DivX is a compressed digital video format

created by the DivX® video codec from DivX, Inc. This player can play DivX video files burned on CD-R/RW and DVD-R/RW/ROM discs. Keeping the same terminology as DVD-Video,

En

Additional information

10

individual DivX video files are called ‘Titles’. When naming files/titles on a CD-R/RW or DVD-R/RW disc prior to burning, keep in mind that by default they will play in alphabetical order.

DivX video compatibility

Official DivX® Certified product.

Plays all versions of DivX® video (including DivX®6) with standard playback of DivX® media files.1

File extensions: .avi and .divx (these must be used for the player to recognize DivX video files). Note that all files with the .avi extension are recognized as MPEG4, but not all of these are necessarily DivX video files and therefore may not be playable on this player.

Displaying DivX subtitle files

The font sets listed below are available for DivX external subtitle files. You can see the proper font set on-screen by setting the Subtitle Language (in Language settings on page 27)

to match the subtitle file.2

Group 1: Albanian (sq), Basque (eu), Catalan (ca), Danish (da), Dutch (nl), English (en), Faroese (fo), Finnish (fi), French (fr), German (de), Icelandic (is), Irish (ga), Italian (it), Norwegian (no), Portuguese (pt), RhaetoRomanic (rm), Scottish (gd), Spanish (es), Swedish (sv) Group 2: Albanian (sq), Croatian (hr), Czech (cs), Hungarian (hu), Polish (pl), Romanian (ro), Slovak (sk), Slovenian (sl)

Group 3: Bulgarian (bg), Byelorussian (be), Macedonian (mk), Russian (ru), Serbian (sr), Ukrainian (uk)

Group 4: Hebrew (iw), Yiddish (ji) Group 5: Turkish (tr)

About MPEG-4 AAC

English

MPEG-2 AAC, forming the basis of the MPEG-4

Advanced Audio Coding (AAC) is at the core of

 

the MPEG-4 AAC standard, which incorporates

 

audio compression technology. The file format

 

and extension used depend on the application

 

used to encode the AAC file. This unit plays

Deutsch

back AAC files encoded by iTunes® bearing

 

the extension '.m4a'. DRM-protected files will

 

not play, and files encoded with some versions

 

of iTunes® may not play, or filenames may

 

display incorrectly.

FranÁais

Apple and iTunes are trademarks of Apple Computer,

 

Inc., registered in the U.S. and other countries.

 

About WMA

Italiano

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The Windows Media® logo printed on the box

 

Nederlands

 

 

 

indicates that this player can playback

 

 

Windows Media Audio content.

 

 

WMA is an acronym for Windows Media Audio

 

 

and refers to an audio compression technology

 

 

 

 

developed by Microsoft Corporation. WMA

EspaÒol

Player for Windows® XP, or Windows Media®

content can be encoded by using Windows

 

Media® Player version 7, 7.1, Windows Media®

 

Player 9 Series.

 

Microsoft, Windows Media, and the Windows logo are

 

 

trademarks, or registered trademarks of Microsoft

 

Corporation in the United States and/or other countries.

 

DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license.

Note

1Playback of .avi video files larger than 4 GB is not possible.

2• For external subtitle files the following subtitle format filename extensions are supported (please note that these files are not shown within the disc navigation menu): .srt, .sub, .ssa, .smi

Some external subtitle files may be displayed incorrectly or not at all.

The filename of the movie file has to be repeated at the beginning of the filename for the external subtitle file.

The number of external subtitle files which can be switched for the same movie file is limited to a maximum of 10.

37

En

10 Additional information

Using and taking care of discs

Handling discs

Hold the disc by its edges when handling so as not to leave fingerprints, dirt or scratches on either side of the disc. Damaged or dirty discs can affect playback performance.

If a disc becomes marked with fingerprints, dust, etc., clean using a soft, dry cloth.

Wipe lightly from the center of the disc using straight strokes. Don’t wipe the disc surface with circular strokes.

If necessary, use a cloth soaked in alcohol, or a commercially available CD/DVD cleaning kit to clean a disc more thoroughly. Never use benzine, thinner or other cleaning agents such as those designed for cleaning vinyl records.

Storing discs

Avoid leaving discs in excessively cold, humid, or hot environments (including under direct sunlight). Don't glue paper or put stickers onto the disc, or use a pencil, ball-point pen or other sharp-tipped writing instrument. These could all damage the disc.

Discs to avoid

Discs spin at high speed inside the player. If a disc is cracked, chipped, warped, or otherwise damaged, don't risk using it in your player— you could end up damaging the unit.

This unit is designed for use with conventional, fully circular discs only. Pioneer disclaims all liability arising in connection with the use of shaped discs.

38

DVD Video regions

All DVD Video discs carry a region mark that indicates which region(s) of the world the disc is compatible with. Your DVD system also has a region mark (on the rear panel). Discs from incompatible regions will not play in this player. In this instance, the following message appears on-screen:

Incompatible disc region number

Canít play disc

Discs marked ALL play in any player.

Installation and maintenance

Hints on installation

We want you to enjoy using this system for years to come, so please bear in mind the following points when choosing a location:

Do...

Use in a well-ventilated room.

Place on a solid, flat, level surface, such as a table, shelf or stereo rack.

Donít...

Use in a place exposed to high temperatures or humidity, including near radiators and other heat-generating appliances.

Place on a window sill or other place where the system will be exposed to direct sunlight.

Use in an excessively dusty or damp environment.

Place directly on top of an amplifier, or other component in your stereo system that becomes hot in use.

Use near a television or monitor as you may experience interference—especially if the television uses an indoor antenna.

Use in a kitchen or other room where the system may be exposed to smoke or steam.

Use on a thick rug or carpet, or cover with cloth—this may prevent proper cooling of the system unit.

Place on an unstable surface, or one that is not large enough to support all four of the system unit’s feet.

En

Additional information

10

Cleaning the pickup lens

The DVD player’s lens should not become dirty in normal use, but if for some reason it should malfunction due to dust or dirt, consult your nearest Pioneer authorized service center. Although lens cleaners are commercially available, we do not recommend using them since some may damage the lens.

Problems with condensation

Condensation may form inside the player if it is brought into a warm room from outside, or if the temperature of the room rises quickly. Although the condensation won’t damage the player, it may temporarily impair performance. Leave it to adjust to the warmer temperature for about an hour before switching on.

Moving the system unit

If you need to move the main unit, first remove a disc if there’s one in the player, then press STANDBY/ON on the front panel to turn the system off. Wait for GOOD BYE to disappear

from the display, then unplug the power cord.1 Never lift or move the unit during playback— discs rotate at high speeds and may damage.

Screen sizes and disc formats

DVD-Video discs come in different screen aspects, ranging from TV programs, which are generally 4:3, to CinemaScope widescreen

movies2, with an aspect ratio of up to about 7:3.

Televisions also come in different aspect ratios; ‘standard’ 4:3 and widescreen 16:9.3

Set to 4:3 (Letter Box), widescreen discs are shown with black bars top and bottom.

Set to 4:3 (Pan&Scan), widescreen discs are shown with the left and right sides cropped. Although the picture looks larger, you don’t actually see the whole picture.

EspaÒol Nederlands Italiano FranÁais Deutsch English

Note

1Unplugging the unit before GOOD BYE disappears from the display may cause the system to return to the factory settings.

2Many widescreen discs override the system’s settings so that the disc is shown in letterbox format regardless of the setting.

3• Using the 16:9 (Wide) setting with a standard 4:3 TV, or one of the 4:3 settings with a widescreen TV, will result in distortion.

When you watch discs recorded in 4:3 format, you can use the TV controls to select how the picture is presented. Your TV may offer various zoom and stretch options; see the instructions that came with your TV for details.

Some movie aspect ratios are wider than 16:9, so even with a widescreen TV, these discs will still play in a ‘letterbox’ style.

39

En

10 Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

If the system does not operate normally due to external effects such as static electricity disconnect the plug from the outlet and insert again to return to normal operating conditions.

General

Problem

Remedy

 

The power does not turn

• Wait for one minute before switching back on.

on, or switches off

• Make sure there are no loose strands of wire touching the unit. This could cause

suddenly (an error

the system to shut off automatically.

message may be

• Check that the speakers are connected correctly.

displayed at startup).

• Make sure the voltage of the mains power source is correct for the model.

 

• Try reducing the volume level.

 

• If the problem persists, take it to your nearest Pioneer authorized service center

 

or your dealer for servicing.

 

 

No sound is output

• If you’re using the line input, make sure the component is connected correctly

when a function is

(see Connecting auxiliary audio components on page 31).

selected.

• Press MUTE on the remote control to turn muting off.

 

 

No sound from surround

• Refer to Channel level setting on page 25 to check the speaker levels.

or center speakers.

• When TUNER is selected, you can only hear the source in stereo.

 

• Check that you haven’t selected the AUTO, STEREO or VIRTUAL mode (see

 

Listening to your system on page 14).

 

• Connect the speakers properly (refer to the Setup Guide).

 

• If the source is 96 kHz, it will be played in stereo.

 

 

Can’t operate the remote

• Replace the batteries (refer to the Setup Guide).

control.

• Operate within 7 m, 30° of the remote sensor (refer to the Setup Guide).

 

• Remove any obstacles or operate from another position.

 

• Avoid exposing the remote sensor on the front panel to direct light.

 

• Check that there’s nothing mistakenly plugged into the CONTROL IN jack.

 

• If the system is connected to a Pioneer plasma display with an SR+ cable, check

 

that the plasma display is switched on. Point the remote control at the plasma

 

display in order to operate the system.

 

 

 

TRAYLOCK shows in the

• Press and hold

(eject) on the front panel for about eight seconds. Then the tray

display and the tray can’t

can be opened/closed using (eject).

be ejected.

 

 

 

 

 

SND. DEMO shows in

• Press and hold

(stop) on the front panel for about five seconds. The disc tray

the display and the unit

ejects automatically to indicate the Sound Demo mode is disabled.

can’t be controlled.

 

 

 

 

 

40

En

Additional information

10

DVD/CD/Video CD player

Problem

Remedy

The disc is ejected

• Clean the disc and align the disc properly in the disc guide.

automatically after

• If the region number on a DVD-video disc does not match the number on the

loading.

player, the disc cannot be used (see DVD Video regions on page 38). In this

 

instance, the following message appears on screen: Incompatible disc region

 

number / Canít play disc.

 

• Allow time for any condensation inside the player to evaporate. Avoid using the

 

player near an air-conditioning unit.

 

 

Playback not possible.

• If the disc is loaded upside down, reload the disc with label side face up.

 

 

Picture playback stops

• Press (stop), then (play) to start playback again.

and buttons cannot be

• Switch the power off once, then on again using the front panel

used.

STANDBY/ON button.

 

 

Settings are canceled.

• When the power is cut, settings will be canceled.

 

 

No picture/No color.

• Check that connections are correct and that plugs are inserted fully.

 

• Check the manual of the TV/monitor to make sure the settings are correct.

 

• If the Progressive setting is selected and you have used component video cables

 

to connect a TV that is not compatible with a progressive scan signal, you will not

 

be able to see any picture at all. With your TV connected using either the

 

composite or S-video terminals, change the Component Out setting to Interlace

 

(see Video Output settings on page 27).

 

 

Screen is stretched or

• The TV Screen setting is incorrect. Set the TV Screen option to match the TV/

aspect doesn’t change.

monitor you're using (see Video Output settings on page 27).

 

 

When recorded on a

• This system uses copy-protection technology which may prevent recording or

VCR or passed through

cause picture problems when connected through a VCR or AV selector. This is not

an AV selector, there is

a malfunction.

disturbance in the

 

playback picture.

 

 

 

Picture disturbance

• This player is compatible with Macro-Vision System copy guard. Some discs

during playback or dark.

include a copy prevention signal, and when this type of disc is played back, stripes

 

etc., may appear on some sections of the picture depending on the TV. This is not a

 

malfunction.

 

• Discs respond differently to particular player functions. This may result in the

 

screen becoming black for a brief instant or shaking slightly when the function is

 

executed. These problems are largely due to differences between discs and disc

 

content and are not malfunctions of this player.

 

 

Noticeable difference in

• DVDs and CDs use different recording methods. This is not a malfunction.

DVD and CD volume.

 

 

 

CD-ROM disc is not

• Make sure that the CD-ROM was recorded using the ISO 9660 disc format. See

recognized.

Disc compatibility table on page 36 for more on disc compatibility.

 

 

DVD-ROM disc is not

• Make sure that the DVD-ROM was recorded using the UDF bridge format. See

recognized.

Disc compatibility table on page 36 for more on disc compatibility.

 

 

EspaÒol Nederlands Italiano FranÁais Deutsch English

41

En

10 Additional information

Problem

Remedy

Files don’t show up in

• The files on the disc must be named with the correct file extension: .mp3 for MP3

the Disc Navigator/

files; .wma for WMA files; .m4a for MPEG-4 AAC files; .jpg for JPEG files (upper or

Photo Browser.

lower-case is OK). See Disc compatibility table on page 36.

 

 

Can’t play WMA or

• The files were recorded using DRM (digital rights management). This is not a

MPEG-4 AAC files.

malfunction.

 

 

Tuner

Problem

Remedy

Considerable noise in

• Connect the AM antenna (refer to the Setup Guide) and adjust the direction and

radio broadcasts.

position for best reception. You may also connect an additional internal or external

 

AM antenna (refer to Connecting external antennas on page 31).

 

• Fully extend the FM wire antenna, position for best reception, and secure to a

 

wall. You may also connect an outdoor FM antenna (see Connecting external

 

antennas on page 31).

 

• Turn off other equipment that may be causing the noise or move it further away.

 

• The tuning interval is incorrect for your country or region. See Frequency step

 

setting on page 34 to switch the tuning interval.

 

 

Auto tuning does not

• The radio signal is weak. Auto tuning will only detect radio stations with a good

pick up some stations.

signal. For more sensitive tuning, connect an outdoor antenna.

 

 

USB connection

Problem

Remedy

USB mass storage

• Make sure you have completely inserted the USB connector to this unit.

device is not recognized

• Check that the memory format is FAT16 or FAT32.

by the system.

• USB devices with an internal USB hub are not supported.

 

 

Files don’t show up in

• The files must have the correct file extension: .mp3 for MP3 files; .wma for WMA

the Navigator/Photo

files; .m4a for MPEG-4 AAC files; .jpg for JPEG files (upper or lower-case is OK).

Browser.

• Make sure the file permission hasn’t been restricted (through a password, etc.).

 

 

Can’t play WMA or

• The files were recorded using DRM (digital rights management). This is not a

MPEG-4 AAC files.

malfunction.

 

 

Error Messages

Message

Description

2CH ONLY

• An operation is prohibited because it is only applicable to 2 channel sources,

 

while the current source is a multichannel source.

 

 

96K

• An operation is prohibited because the source is 96 kHz digital.

 

 

SND. DEMO

• The sound demo is on. See General in Troubleshooting on page 40.

 

 

NOISY

• Background noise is too high to complete MCACC setup successfully.

 

 

42

En

Additional information

10

Message

Description

ERR MIC

• An error occured during MCACC setup because the microphone is not

 

connected or is not connected properly.

 

 

ERR SP

• An error occured during MCACC setup because the speakers are not connected

 

or are not connected properly.

 

 

MUTING

• An operation is prohibited because the sound is muted (press MUTE).

 

 

STEREO

• An operation is prohibited because the tuner is selected.

 

 

TRAYLOCK

• The tray lock is on. See General in Troubleshooting on page 40.

 

 

KEY LOCK

• The key lock is enabled. See Key lock setting on page 35.

 

 

PHONESIN

• An operation is prohibited because the headphones are connected.

 

 

USB ERR

• See Important in Using the USB interface on page 23 for more on this.

 

 

EEP ERR

• Contact your Pioneer authorized service center or your dealer for servicing.

 

 

EXIT

• Appears when a menu is automatically exited after a set period of inactivity.

 

 

Resetting the system

Use the front panel controls to reset all system settings to the factory default.

With the system on, press

STANDBY/

ON while holding down

USB.

The next time you switch on, all the system settings should be reset.

Using the language code list

Some of the language options (see Language settings on page 27) allow you to set your preferred language from any of the 136 languages in the Language code list below.

1Select ëOther Languageí.

2 Use / to select either a code letter or a code number.

3 Use / to select a code letter or a code number.

See the Language code list (next page) for a complete list of languages and codes.

EspaÒol Nederlands Italiano FranÁais Deutsch English

43

En

10 Additional information

Language code list

Language (Language code letter), Language code

Japanese (ja), 1001

English (en), 0514

French (fr), 0618

German (de), 0405

Italian (it), 0920

Spanish (es), 0519

Dutch (nl), 1412

Russian (ru), 1821

Chinese (zh), 2608

Korean (ko), 1115

Greek (el), 0512

Afar (aa), 0101

Abkhazian (ab), 0102

Afrikaans (af), 0106

Amharic (am), 0113

Arabic (ar), 0118

Assamese (as), 0119

Aymara (ay), 0125

Azerbaijani (az), 0126

Bashkir (ba), 0201

Byelorussian (be), 0205

Bulgarian (bg), 0207

Bihari (bh), 0208

Bislama (bi), 0209

Bengali (bn), 0214

Tibetan (bo), 0215

Breton (br), 0218

Catalan (ca), 0301

Corsican (co), 0315

Czech (cs), 0319

Welsh (cy), 0325

Danish (da), 0401

Bhutani (dz), 0426

Esperanto (eo), 0515

Estonian (et), 0520

Basque (eu), 0521

Persian (fa), 0601

Finnish (fi), 0609

Fiji (fj), 0610

Faroese (fo), 0615

Frisian (fy), 0625

Irish (ga), 0701

Scots-Gaelic (gd), 0704

Galician (gl), 0712

Guarani (gn), 0714

Gujarati (gu), 0721

Hausa (ha), 0801

Hindi (hi), 0809

Croatian (hr), 0818

Hungarian (hu), 0821

Armenian (hy), 0825

Interlingua (ia), 0901

Interlingue (ie), 0905

Inupiak (ik), 0911

Indonesian (in), 0914

Icelandic (is), 0919

Hebrew (iw), 0923

Yiddish (ji), 1009

Javanese (jw), 1023

Georgian (ka), 1101

Kazakh (kk), 1111

Greenlandic (kl), 1112

Cambodian (km), 1113

Kannada (kn), 1114

Kashmiri (ks), 1119

Kurdish (ku), 1121

Kirghiz (ky), 1125

Latin (la), 1201

Lingala (ln), 1214

Slovak (sk), 1911

Laothian (lo), 1215

Slovenian (sl), 1912

Lithuanian (lt), 1220

Samoan (sm), 1913

Latvian (lv), 1222

Shona (sn), 1914

Malagasy (mg), 1307

Somali (so), 1915

Maori (mi), 1309

Albanian (sq), 1917

Macedonian (mk), 1311

Serbian (sr), 1918

Malayalam (ml), 1312

Siswati (ss), 1919

Mongolian (mn), 1314

Sesotho (st), 1920

Moldavian (mo), 1315

Sundanese (su), 1921

Marathi (mr), 1318

Swedish (sv), 1922

Malay (ms), 1319

Swahili (sw), 1923

Maltese (mt), 1320

Tamil (ta), 2001

Burmese (my), 1325

Telugu (te), 2005

Nauru (na), 1401

Tajik (tg), 2007

Nepali (ne), 1405

Thai (th), 2008

Norwegian (no), 1415

Tigrinya (ti), 2009

Occitan (oc), 1503

Turkmen (tk), 2011

Oromo (om), 1513

Tagalog (tl), 2012

Oriya (or), 1518

Setswana (tn), 2014

Panjabi (pa), 1601

Tonga (to), 2015

Polish (pl), 1612

Turkish (tr), 2018

Pashto, Pushto (ps), 1619

Tsonga (ts), 2019

Portuguese (pt), 1620

Tatar (tt), 2020

Quechua (qu), 1721

Twi (tw), 2023

Rhaeto-Romance (rm), 1813

Ukrainian (uk), 2111

Kirundi (rn), 1814

Urdu (ur), 2118

Romanian (ro), 1815

Uzbek (uz), 2126

Kinyarwanda (rw), 1823

Vietnamese (vi), 2209

Sanskrit (sa), 1901

Volapük (vo), 2215

Sindhi (sd), 1904

Wolof (wo), 2315

Sangho (sg), 1907

Xhosa (xh), 2408

Serbo-Croatian (sh), 1908

Yoruba (yo), 2515

Sinhalese (si), 1909

Zulu (zu), 2621

Country/Area code list

Country/Area, Country/Area code, Country/Area code letter

Argentina, 0118, ar

Hong Kong, 0811, hk

Philippines, 1608, ph

Australia, 0121, au

India, 0914, in

Portugal, 1620, pt

Austria, 0120, at

Indonesia, 0904, id

Russian Federation, 1821, ru

Belgium, 0205, be

Italy, 0920, it

Singapore, 1907, sg

Brazil, 0218, br

Japan, 1016, jp

Spain, 0519, es

Canada, 0301, ca

Korea, Republic of, 1118, kr

Switzerland, 0308, ch

Chile, 0312, cl

Malaysia, 1325, my

Sweden, 1905, se

China, 0314, cn

Mexico, 1324, mx

Taiwan, 2023, tw

Denmark, 0411, dk

Netherlands, 1412, nl

Thailand, 2008, th

Finland, 0609, fi

New Zealand, 1426, nz

United Kingdom, 0702, gb

France, 0618, fr

Norway, 1415, no

United States of America, 2119, us

Germany, 0405, de

Pakistan, 1611, pk

 

44

En

Additional information

Specifications

Amplifier section

RMS Power Output:

Front, Center, Surround . . 100 W per channel (1 kHz, 10 % T.H.D., 4 Ω)

Subwoofer . 100 W (100 Hz, 10 % T.H.D., 4 Ω)

Disc section

Digital audio

characteristics . . . . . . . . .DVD fs: 96 kHz, 24-bit Type. . . . . . . .DVD system, Video CD/Super VCD system and Compact Disc digital audio system Frequency

response. . . . 4 Hz to 44 kHz (96 kHz sampling) / 4 Hz to 22 kHz (48 kHz sampling)

Wow and Flutter. . . . . . . . Limit of measurement (±0.001 % W.PEAK) or less (JEITA)

FM tuner section

Frequency range . . . . . . . . 87.5 MHz to 108 MHz Antenna . . . . . . . . . . . . . . . . . . 75 Ω, unbalanced

AM tuner section

Frequency range:

With 9 kHz step . . . . . . . . 531 kHz to 1602 kHz With 10 kHz step . . . . . . . 530 kHz to 1700 kHz Antenna . . . . . . . . . . . . . . . . . . . . . Loop antenna

Miscellaneous

Power requirements:

Taiwan (and similar regional models):

. . . . . . . . . . . AC 110 V to 240 V, 50 Hz /60 Hz Singapore (and similar regional models):

. . . . . . . . . . . AC 220 V to 240 V, 50 Hz /60 Hz Power consumption . . . . . . . . . . . . . . . . . . .55 W Power consumption in standby . . . . . . . . 0.29 W Dimensions . . 420 mm (W) x 60 mm (H) x 330 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3 kg

Accessories (DVD/CD receiver)

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AA/R6 dry cell batteries . . . . . . . . . . . . . . . . . . . 2 (to confirm system operation)

Video cable (yellow plugs) . . . . . . . . . . . . . . . . . 1 AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . 1 FM antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Microphone (for Auto MCACC setup) . . . . . . . . 1

10

Power cord (2 power cords are supplied with

English

some regional models)

 

 

 

Setup Guide

 

 

 

These operating instructions

 

 

 

S-DV353 Speaker system

 

Front/surround speakers

Deutsch

 

Enclosure . . . . .

. . . . Closed-box bookshelf type

 

 

 

(magnetically shielded)

 

System . . . . . . . .

. . . . . . .

. . 7.7 cm 1-way system

 

. . . . . .Speakers

. . . . . . .

. . . . . 7.7 cm cone type

 

Nominal impedance. . . .

. . . . . . . . . . . . . . . . 4 Ω

FranÁais

Frequency range

 

80 Hz to 20 kHz

. . . . . .

 

Maximum input power. .

. . . . . . . . . . . . . . 100 W

 

Dimensions . . . .

100 mm (W) x 136 mm (H) x 80 mm (D)

 

Weight . . . . . . . .

. . . . . . .

. . . . . . . . . . . . . 0.55 kg

 

Center speaker

Enclosure

Closed-box bookshelf type

Italiano

 

 

 

(magnetically shielded)

 

System . . . . . . . . .

. . . . . .

. . 7.7 cm 1-way system

 

Speakers . . . . . . .

. . . . . .

. . . . . 7.7 cm cone type

 

Nominal impedance. . . .

. . . . . . . . . . . . . . . . 4 Ω

 

Frequency range

 

75 Hz to 20 kHz

 

. . . . . .

Nederlands

Maximum input power

100 W

 

Dimensions . . . . .

270 mm (W) x 96 mm (H) x 90 mm (D)

 

Weight . . . . . . . . .

. . . . . .

. . . . . . . . . . . . . 0.78 kg

 

Subwoofer

 

 

 

 

 

 

Enclosure

Bass-reflex floorstanding type

 

EspaÒol

System

 

16 cm 1-way system

. . . . . .

 

Speaker . . . . . . . .

. . . . . .

. . . . . .16 cm cone type

 

Nominal impedance. . . .

. . . . . . . . . . . . . . . . 4 Ω

 

Frequency range

. . . . . .

. . . . . . 30 Hz to 2.5 kHz

 

Maximum Input Power

100 W

 

 

Dimensions . . . 190 mm (W) x 360 mm (H) x 320 mm (D)

 

Weight . . . . . . . . .

. . . . . .

. . . . . . . . . . . . . . 4.0 kg

 

Accessories

Speaker cables . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Speaker stands (for surround speakers) . . . . . 2 Screws (for stands). . . . . . . . . . . . . . . . . . . . . . . 2 Non-skid pads (small) . . . . . . . . . . . . . . . . . . . 20 Non-skid pads (large) . . . . . . . . . . . . . . . . . . . . . 4

45

En

10 Additional information

S-DV555T Speaker system

Front speakers

Enclosure. . . . . . . Closed-box floorstanding type (magnetically shielded)

System . . . . . . . . . . . . . . . . . . . . . . . 2-way system Speakers:

Woofer . . . . . . . . . . . . . . . 7.7 cm cone typex2 Tweeter . . . . . . . . . . . .2.6 cm semi-dome type Nominal impedance . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . . . 70 Hz to 20 kHz Maximum input power . . . . . . . . . . . . . . . . 100 W Dimensions . 260 mm (W) x 1096.5 mm (H) x 260 mm (D)

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 kg

Center speaker

Enclosure. . . . . . . . . . Closed-box bookshelf type (magnetically shielded)

System . . . . . . . . . . . . . . . . . 7.7 cm 1-way system Speakers . . . . . . . . . . . . . . . . . . 7.7 cm cone type Nominal impedance . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . . . 75 Hz to 20 kHz Maximum input power . . . . . . . . . . . . . . . . 100 W Dimensions . . . . . 270 mm (W) x 96 mm (H) x 90 mm (D)

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.78 kg

Surround speakers

Enclosure. . . . . . . . . . Closed-box bookshelf type (magnetically shielded)

System . . . . . . . . . . . . . . . . . 7.7 cm 1-way system Speakers . . . . . . . . . . . . . . . . . . 7.7 cm cone type Nominal impedance . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . . . 80 Hz to 20 kHz Maximum input power . . . . . . . . . . . . . . . . 100 W Dimensions . . . . 100 mm (W) x 136 mm (H) x 80 mm (D)

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.55 kg

Accessories

Speaker cables . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Small non-skid pads . . . . . . . . . . . . . . . . . . . . . 12 Large non-skid pads . . . . . . . . . . . . . . . . . . . . . . 8 Speaker stands . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Speaker stand bases . . . . . . . . . . . . . . . . . . . . . 2 Screws (for bases) . . . . . . . . . . . . . . . . . . . . . . . 6

S-DV1SW Speaker system

Subwoofer (SW)

Enclosure. . . . . . . Bass-reflex floorstanding type

46

System . . . . . . . . . . . . . . . . . 16 cm 1-way system Speaker. . . . . . . . . . . . . . . . . . . . 16 cm cone type Nominal impedance . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . . . 30 Hz to 2.5 kHz Maximum Input Power . . . . . . . . . . . . . . . .100 W Dimensions . . . 220 mm (W) x 421 mm (H) x 402 mm (D)

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.0 kg

Accessories

Speaker cables. . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Large non-skid pads . . . . . . . . . . . . . . . . . . . . . . 6

Note

Specifications and design subject to possible modification without notice, due to improvements.

This product includes FontAvenue® fonts licenced by NEC corporation. FontAvenue is a registered trademark of NEC Corporation.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

DRM (digital rights management) copy protection is a technology designed to prevent unauthorized copying by restricting playback, etc. of compressed audio files on devices other than the PC (or other recording equipment) used to record it. For detailed information, please see the instruction manuals or help files that came with your PC and/or software.

En

Additional information

Manufactured under license from Dolby Laboratories.“Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc.

10

EspaÒol Nederlands Italiano FranÁais Deutsch English

47

En

Pioneer

D3-4-2-1-7b_A_ChH

D3-4-2-1-7c_A_ChH

D3-4-2-2-2a_A_ChH

CLASS 1

LASER PRODUCT

CAUTION : CLASS 3B VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN, AVOID

EXPOSURE TO THE BEAM.

VRW2159

D3-4-2-1-8_A_ChH

01

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

02

. . . . . . . . . . . . . . . . . . . .9

Auto MCACC . . . . . . . . . . . . . . .9(OSD) . . . . . . . . . . . . . .10. . . . . . . . . . . . . . . . . . . . . . . . . .11

. . . . . . . . . . . . . . . . . . . . .11. . . . . . . . . . . .11 DVD-Video . . . . . . . . . . . . . . . .12 VCD/ VCD PBC . . . . . . . . . . . . . .12. . . . . . . . . . . . . . . . . . . . . . . .12FM . . . . . . . . . . . . . . . . . . .12AM . . . . . . . . . . . . . . . . . . .13. . . . . . . . . . . . . . . . . . . . . . . . .13. . . . . . . . . . . . . . . . . . . . .13. . . . . . . . . . . . . . . . . . . . . . .13

03

. . . . . . . . . . . . . . . . . . . . . . .14. . . . . . . . . . . . . . . . . . . . . . .14

Dolby Pro Logic II Music . . . . .14

. . . . . . . . . . . . .15. . . . . . . . . . . . .15. . . . . . . . . . . . . . . . . . . . . . .15. . . . . . . . . . . . . . . . . . . . . . .15

. . . . . . . .15

. . . . . . . . . . . . .16. . . . . . . . . . . . . . . . . . . . . . . . . .16. . . . . . . . . . . . . . .16. . . . . . . . . . . . . . . . . . . .16. . . . . . . . . . . .16. . . . . . . . . . . . . . . . . . . . . . .16

04

. . . . . . . . . . . . . . . . . . . . . . . . . .17. . . . . . . . . . . . . . . . . . . . . . . .17. . . . . . . . . . . . . . . . . . . . .17JPEG . . . . . . . . . . . . . . . . . .17

DVD VCD/

VCD . . . . . . . . . . . . . . . . . . . . . . .18

4

WMA MP3 MPEG-4 AAC DivX

JPEG . . . . . . . . . . . . . . . . . . . . . . . . 19. . . . . . . . . . . . . . . 19. . . . . . . . . . . . . . . . . . . 19. . . . . . . . . . . . . . . . . . . 20. . . . . . . . . . . . . . . . . . . 20

. . . . . . . 21

. . . . . . . . . . . . . . . . . . . . . . . . . . 21. . . . . . . . . . . . . . . . . . . . . . . . . . 21. . . . . . . . . . . . . . . . . . . . 21. . . . . . . . . . . . . . . . . . . . . . . . . . 22. . . . . . . . . . . . . . . . . . . . . . 22. . . . . . . . . . . . . . . . . . . . . . 22

05 USB

USB . . . . . . . . . . . . . . . . . . . . . . 23. . . . . . . . . . . . . . . . . . . . . . 23. . . . . . . . . . . . . . . . . . . . . . . . . . 24JPEG . . . . . . . . . . . . . . . . . . 24. . . . . . . . . . . . . 24

06

. . . . . . . . . . . . . . . . . . 25

07

. . . . . . . . . . . . . . . . . . . 26

08

. . . . . . . . . . . . . . . 27. . . . . . . . . . . . . . . . . . . . 27. . . . . . . . . . . . . . . . . . . . . . . . 27. . . . . . . . . . . . . . . . . . . . . . 28. . . . . . . . . . . . . . . . . . . . . . . . 28

. . . . . . . . . . . . . . . . . . . . . . . . . 28DivX®VOD . . . . . . . . . . . . . . . . 29

09

. . . . . . . . . . . . . . . . . . . . . . 31. . . . . . . . . . . . . . . . . . . 31S-video . . . . . . . . . . . . . . . . . . . 31. . . . . . . . . . . . . . . 32. . . . . . . . . . . . . . . . . . 32

Pioneer

. . . . . . . . . . . . . . . . . . . . . . . . . . 32

Pioneer SR+ . . . . . . . 33

SR+ . . . . . . . . . . . . . . . . . . . . . 33

ChH

10

. . . . . . . . . . . . . . . . . . . . 34. . . . . . . . . . . . . . . . . . . . 35. . . . . . . . . . . . . . . . . . . . 35. . . . . . . . . . . 35. . . . . . . . . . . . . . . . . 36DVD+R/DVD+RW . . . . . . . . . . . 36DivX. . . . . . . . . . . . . . . . . . . . . . . . 36MPEG-4 AAC . . . . . . . . . . . . . . . . . . 37WMA. . . . . . . . . . . . . . . . . . . . . . . . . 37. . . . . . . . . . . . . . . . . . 38 DVD Video . . . . . . . . . . . . . . . . 38. . . . . . . . . . . . . . . . . . . . . . . . 38. . . . . . . . . . . . . . . . . . . . . . . . 38. . . . . . . . . . . . . . . . . . . . . 39. . . . . . . . . . . . . . . . . . . . . 39. . . . . . . . . . . . . . . . . . . . . 39. . . . . . . . . . . . . . . . 39. . . . . . . . . . . . . . . . . . . . . . . . . 40. . . . . . . . . . . . . . . . . . . . . . . . 40 DVD/CD/VCD . . . . . . . . . . . . . . . . . 41. . . . . . . . . . . . . . . . . . . . . . . . . . 42 USB . . . . . . . . . . . . . . . . . . . . . . . . . 42. . . . . . . . . . . . . . . . . . . . . . . . 42. . . . . . . . . . . . . . . . . . . . . . 43. . . . . . . . . . . . . . . . . . 43. . . . . . . . . . . . . . . . . . . . . . 44. . . . . . . . . . . . . . . . 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

EspaÒol Nederlands Italiano FranÁais English

5

ChH

01

1

OPEN/CLOSE DVD/CD USB VOLUME STANDBY/ON

1

2

3

4

5

6

9

78

1 OPEN/CLOSE

2DVD/CD

DVD/CD

3

4USB

USB

5VOLUME

6 STANDBY/ON

7USB

USB 23 USB

8 PHONES

6

 

STANDBY

DVD/CD

TUNER

 

 

1

/ON

(FM/AM)

 

 

 

 

 

 

OPEN/

 

2

 

 

USB

LINE

CLOSE

11

 

 

 

 

 

 

 

 

 

 

 

 

 

AUDIO

 

 

1

 

2

3

 

 

 

 

 

 

 

SUBTITLE

 

3

4

 

5

6

 

12

 

 

 

 

ANGLE

 

7

 

8

9

 

 

 

CLEAR

 

 

DISPLAY

ZOOM

 

 

 

 

 

 

 

 

 

0

 

 

 

4

TOPMENU

 

TUNE

 

MENU

13

SETUP

 

 

 

SR

5

 

 

 

 

ST

 

ENTER

ST

 

 

HOME

 

 

 

 

 

 

MENU

 

 

 

RETURN

 

6

MCACC

TUNE

 

TEST TONE

14

 

 

 

7

SOUND

 

 

 

 

 

RETRIEVER

SURROUND

ADVANCED

SOUND

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

 

TV CONTROL

 

SLEEP

15

9

 

 

 

 

 

INPUT

CHANNEL

VOLUME

MUTE

16

 

SHIFT

 

 

 

 

10

 

 

VOLUME

 

17

 

 

 

 

 

1 STANDBY/ON

DVD/CD TUNER USB LINE

3CLEAR DISPLAY CLEAR

DISPLAY 22

ChH

 

01

4 TOP MENU DVDMENU12

SHIFT+SETUP12 13 25 34 35

5ENTER

/ / /

ENTER

TUNE +/–

ST +/–

6 HOME MENU

SHIFT+MCACC MCACC

9

SOUND RETRIEVER CD16

SURROUND 14

15

ADVANCED Pioneer

15

SOUND 14 16

11 17

23 USB

9 TV CONTROL

Pioneer

10SHIFT

11OPEN/CLOSE

12DVD

AUDIO 21

SUBTITLE 21

ANGLE DVD22

ZOOM 22

13MENU DVD USB18 24

SHIFT+SR+ SR+ 33

14 RETURN

SHIFT+TEST TONE

25

15 SLEEP

35

16 MUTE

17 VOLUME +/–

EspaÒol Nederlands Italiano FranÁais English

7

ChH

01

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

3

4

 

5

6

 

 

PRGSVE SOUND

 

 

 

 

 

 

DTS F.SURR.

 

 

RPT -1

 

 

2D

 

 

 

kHz PGM

 

 

2PL

 

 

 

MHz RDM

 

 

 

 

 

 

 

 

 

14

13

12 11

10

9

8

7

1

DTS

 

 

 

 

9 kHz / MHz

 

 

DTS 14

 

2

PRGSVE

 

 

 

 

kHz AM MHz FM

 

 

10

 

 

 

 

 

 

 

 

 

 

27

11

3SOUND

15

4SURR.

15

F.SURR.

15

5RPT RPT-1

RPT RPT-1

19

6PGM

20

FM

FM

8RDM

20

35

12

13 2 PL II

Dolby Pro Logic II14

14 2 D

Dolby Digital

14

8

ChH

2

55.1

 

 

 

 

 

 

1

3

02

Auto

 

English

 

 

MCACC

 

 

 

 

 

 

Auto MCACC

 

 

 

 

 

(MCACC)

FranÁais

 

 

 

 

 

 

 

Italiano

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Nederlands

 

 

 

 

 

• MCACC

 

 

 

 

 

 

 

 

EspaÒol

 

 

 

 

MENU

 

 

RETURN

 

 

 

 

 

 

CLEAR

 

DISPLAY

ZOOM

 

 

 

 

 

 

 

 

0

 

TV CONTROL

 

SLEEP

 

 

 

 

 

TOPMENU

TUNE

 

MENU

 

 

 

STANDBY

 

TUNER

 

 

 

 

INPUT CHANNEL

VOLUME

MUTE

 

/ON

DVD/CD (FM/AM)

 

SETUP

 

 

SR

 

 

 

 

 

 

OPEN/

 

 

 

SHIFT

VOLUME

 

 

 

USB

LINE

CLOSE

ST

ENTER ST

 

 

 

 

 

HOME

 

 

 

 

 

 

 

 

 

AUDIO

 

 

 

 

 

 

 

1

2

3

 

MCACC

TUNE

 

TEST TONE

 

 

 

 

 

 

SUBTITLE

SOUND

 

 

 

 

 

 

 

 

 

RETRIEVER SURROUND

ADVANCED SOUND

 

 

 

4

5

6

 

 

 

 

 

 

 

 

 

 

 

ANGLE

 

 

 

 

 

 

 

7

8

9

 

 

 

 

 

 

 

 

ZOOM

1 15

2 Auto MCACC

9

ChH

02

 

 

1

MCACC MIC

MCACC

 

COMPLETE3 MCACC

4

 

 

COMPONENT

R

 

 

VIDEO

 

 

VIDEO

 

CB/

 

 

PB

 

FM

 

 

AM LOOP

UNBAL75Ω

 

 

 

IN

 

 

 

S-VIDEO

 

Y

MCACC

 

VIDEO OUT

 

MIC

CONTROL

 

(OSD)

2

或椅子以確保水平。

3 STANDBY/ON

4SHIFT+MCACC

SHIFT+MCACC

音調。

SHIFT+MCACCMCACC

NOISY

51 SHIFT+MCACC

RETRYENTER

ERR MIC ERR SP

RETRY2 ENTER

(OSD)

ENTER

5

ENTER

HOME (OSD)

MENU

ENTER

RETURN

OSD

1

2 SHIFT+MCACC ERR MCACC 3 COMPLETE

4 15

5

10

ChH

DVD CD VCD/ VCD DivX WMA/MP3/MPEG-4 AAC 4

1

視機打開並確定設置的是正確的視頻輸入。

2 OPEN/CLOSE

DVD

3

DVD VCD/ VCDDVD-Video

12 VCD/ VCD PBC

JPEG 17 JPEG

• DivXMP3OSD DivXDivX MP3/ WMA/JPEG/MPEG-4 AAC

VOLUME

02

1 4

English

 

 

 

 

 

 

 

 

 

 

 

 

RESUME LAST

 

 

 

MEM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FranÁais

 

 

 

 

 

 

 

 

 

 

RESUME

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Italiano

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTER

 

 

Nederlands

 

 

 

 

 

 

 

 

DVD CD/VCD/ VCD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VR DVD-RW DVD-

EspaÒol

 

Video CD/VCD/ VCD

 

 

 

 

 

 

 

 

 

RESUME

對於DVD VCD/ VCD

2LAST MEM

1 DVD

2

DVD-Video VR DVD-R/RW

11

ChH

02

顯示RESUME

DVD-Video

DVD-Video

DVD-Video MENUTOP MENU

 

 

 

TOP MENU DVD

 

 

 

 

MENU

DVD

 

 

 

 

 

 

 

 

 

 

ENTER

 

 

 

RETURN

 

 

 

 

 

 

ENTER

 

 

 

 

VCD/ VCD PBC

VCD/ VCD PBC

PBC

PBC VCD/ VCD

RETURN PBC

ENTER

FM AM

1 TUNERAM FM

2

TUNE +/–

TUNE +/–

TUNE +/–

FM

FM

1 FM

SHIFT+SETUP

2 / FM MODE

ENTER

3 / FM MONO

ENTER

FM AUTO

12

ChH

AM

AM AM

1 AM

SHIFT+SETUP

2 / NOISECUT

ENTER

3 /

ENTER

1 3

30

1 AM FM

FMAM

2 SHIFT+SETUP /

ST.MEM. ENTER

3 /

ENTER

1TUNER

2ST +/–

31

USB USB23 USB

1 TV

2LINE

02

EspaÒol Nederlands Italiano FranÁais English

13

ChH

03

3

的通道。

3

9

TUNE

TEST TONE

SOUND

RETRIEVER SURROUND ADVANCED SOUND

MOVIE (Dolby Pro Logic II Movie) Pro Logic II 5.1

MUSIC (Dolby Pro Logic II Music)

Pro Logic II 5.1

STEREO

Dolby Pro Logic II Music

SURROUND AUTO 1 Dolby Pro Logic II Music

2

Dolby Pro Logic

3

9

TUNE

TEST TONE

SOUND

RETRIEVER SURROUND ADVANCED SOUND

景。

1 Dolby Pro Logic II MusicSOUND

2/ C WIDTH

DIMEN PANORAMA ENTER

C WIDTH

SURROUND 1

AUTO

DOLBY PL (Dolby Pro Logic)

4.1

DIMEN.

PANORAMA

1 Dolby Digital DTS

2

14

ChH

 

 

 

03

 

 

TUNE

TEST TONE

 

 

 

SOUND

 

 

 

RETRIEVER SURROUND

ADVANCED SOUND

 

 

 

English

9

 

ADVANCED

 

3

 

 

 

 

 

 

 

 

ADVMOVIE ADVMUSIC

 

 

 

EXPANDED TV SURR. SPORTS GAME

 

 

VIRTUAL 5 STEREO

 

 

 

 

TUNE

TEST TONE

 

 

SOUND

 

 

 

 

RETRIEVER SURROUND ADVANCED

SOUND

 

 

 

 

 

 

 

 

 

 

 

ADVANCED

 

 

 

 

 

 

FranÁais

 

 

 

FRTMUSIC

 

TUNE

TEST TONE

 

FRTMOVIE

 

 

 

EXTPOWER 1

 

 

 

 

 

 

FRTMOVIE

SOUND

 

 

 

 

 

 

 

RETRIEVER SURROUND

ADVANCED SOUND

 

FRTMUSIC

 

 

Italiano

EXTPOWER

 

 

 

SURROUND

 

 

STEREO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Nederlands

 

 

 

 

 

STEREO

 

 

 

 

 

 

 

 

 

 

 

PHONES SURROUND

 

 

 

 

 

 

 

 

 

ADVANCED

Front Music / Front Movie Extra Power

 

 

 

 

 

EspaÒol

 

 

 

PHONES SURROUND

SURROUND

 

 

 

 

 

 

 

STEREO

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

9

Auto MCACC

 

 

 

 

3

 

2

 

 

 

9

 

 

 

 

 

 

 

1

2

15

ChH

03

1 SOUND /

MCACC EQ ENTER

2 / EQ ON

EQ OFF ENTER

EQ OFF

MCACC EQ ON

1 SOUND /

TONE ENTER

2 /

ENTER

功能無法同時使用。

 

 

 

 

 

 

 

 

 

 

WMA/MP3/MPEG-4 AAC

 

/

 

 

 

 

 

BASS

 

TREBLE

/ ENTER

DSP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CD

 

 

 

 

 

 

 

 

 

SOUND

 

 

 

 

 

 

RETRIEVER

 

 

 

 

 

 

 

 

 

 

ENTER

 

 

 

 

 

 

 

 

BASS/TRE

 

 

 

1 SOUND /

 

 

 

 

 

 

 

 

DIALOGUE ENTER

 

 

 

 

2 /

 

ENTER

1

 

 

 

 

OFF MID MAX

1 SOUND /

 

 

 

 

BASSMODE ENTER

 

 

2

/ ENTER

 

 

 

 

 

 

 

 

 

OFF MUSIC

 

 

CINEMA

 

 

 

1

16

ChH

4

1

2

DVD VCD/

VCD CD DivX WMA/MP3/MPEG-4 2 AAC/JPEG

DVD

VCD/ VCD PBC

1

2

DVDVCD/ VCD DivX

1

2

2

JPEG

JPEG3

DVD VCD/ VCD DivX DVD

WMA/MP3/MPEG-4 AAC

 

 

 

 

04

EspaÒol Nederlands Italiano FranÁais English

1 DivX

2 DVD

PBC VCD/ VCD WMA/MP3/MPEG-4 AAC 3

299 648

17

ChH

04

/ / /

ZOOM 1x 2x 4x

MENU

DVD VCD/ VCD

DVD VCD/VCD

1 HOME MENU

18

DVD-Video

DVD-Video

VCD/ VCD

VCD/ VCD 10

Original: VR DVD-RW

Playlist: VR DVD-RW

Original: 10

Playlist: 10

下/

01

02

03

04

05

06

:

0149: --

/ / / ENTER

按下ENTER

ChH

WMA MP3 MPEG-4 AAC DivX JPEG

案或資料夾。

1 HOME MENU

00:00/ 00:00

0kbps

Folder1

Folder2

Folder3

Folder4

2 / / / ENTER

/ 1

ENTER

JPEG

00:00/ 00:00

0kbps

Folder2

File1

File2

File3

File4

File5

3 DivXJPEG ENTER

WMA/MP3/MPEG-4 AAC DivX

 

 

 

 

 

 

 

 

 

04

 

 

 

 

 

 

 

 

 

 

 

 

 

English

 

 

 

 

 

 

 

 

 

• WMA/MP3/MPEG-4 AAC

 

 

 

JPEG

 

 

 

 

 

 

 

JPEG

 

 

 

 

 

 

 

 

 

 

 

 

JPEG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FranÁais

 

 

 

 

 

 

 

 

 

 

 

A-B CD VCD/

 

VCD DVD A

 

B

Italiano

1

 

HOME MENU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Nederlands

 

 

 

 

 

 

 

 

 

2

 

A-B

 

 

 

 

3

 

ENTER

 

 

 

 

 

 

 

4

 

ENTER

 

 

EspaÒol

 

 

ENTER

 

 

 

 

 

 

 

 

 

 

 

 

 

JPEG 20

1 .. ENTER

19

ChH

04

1 HOME MENU

2 1

DVD

CD VCD/ VCD

DivX

DVD-Video CD VCD/ VCD 2

1 HOME MENU

的播放順序程序。3

1 HOME MENU

2

3 / / / ENTER

DVD

CD VCD/ VCD

ENTER

DVD

CD VCD/ VCD

• :

4 3

24

插入編序步驟。

CLEAR

1 WMA/MP3/MPEG-4 AAC

2

VR DVD-RW WMA/MP3/MPEG-4 DivX DVD

3 VR DVD-R/RW WMA/MP3/MPEG-4 AAC DivX DVD

20

ChH

 

04

5

• :

 

 

HOME

 

MENU

 

 

 

 

 

外的其他選項。

輯清單

刪除程序編輯清單

序播放

4

DVD/DivX

CD/VCD/ VCD4 5 0 0

451 20 308 0 3 0

5ENTER

DVD DivX1

SUBTITLE

27

DivX 37DivX

 

 

 

 

 

 

 

 

2

DVD CD VCD/ VCD

3

DivX

AUDIO

 

 

1 HOME MENU

• 27

2

 

 

 

 

1 TOP MENU MENU

2 VCD

3 TOP MENU MENU

EspaÒol Nederlands Italiano FranÁais English

21

ChH

04

DVD DivXVCD/ VCD JPEG

2 4

1 ZOOM2x 4x

2 / / /

大區域。1

DVD

28

ANGLE

顯示在螢幕上。

DISPLAY

DISPLAY

1 DVD VCD/ VCD DivX JPEG 4x

ZOOM

22

ChH

USB

5

USB

USB

USB1 JPEG USB2

1 USB

2USB

USB

USB

Type A

USB

3

USB JPEG 24 JPEG

前面板顯示幕上有顯示USB DATA

05

 

 

 

 

 

 

 

 

 

English

 

 

 

 

 

 

 

 

 

 

 

 

 

 

USB ERR

 

 

 

 

USB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• USB

 

FranÁais

 

 

 

 

 

 

DVD/CD

 

 

 

USB

 

 

 

 

 

• AC

 

 

 

 

 

 

USB

 

 

 

 

 

 

 

 

 

 

 

 

Italiano

USB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Nederlands

 

 

USB

 

 

 

 

 

 

 

 

 

 

 

EspaÒol

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 WMA/MP3/MPEG-4 AAC USB DivX

2 USB FAT16/32 MP3USB

Pioneer USB

USB

23

ChH

05 USB

1

MENU

WMA MP3 MPEG-4 AAC JPEG 3

JPEG

片展示。2

WMA/MP3/MPEG-4 AAC

/ / /

ZOOM 1 24

1 MENU / / /

ENTER

/ 4

ENTER

JPEG

2 JPEGENTER

WMA/MP3/MPEG-4 AAC

JPEG

WMA/MP3/MPEG-4 AACJPEGJPEGJPEG

1 WMA/MP3/MPEG-4 AAC

2

USB 299 648 3

4 .. ENTER

24

ChH

6

效設定值1 MCACC 9

1 SHIFT+SETUP /

ENTER

2

2 / ENTER

MCACC 9

3

/

L

C

R

SR

SL

SW

± 10 dB

06

 

 

 

English

 

 

 

 

 

 

DISTANCE

 

 

 

 

 

ENTER

 

/ /

 

 

 

 

L

 

 

 

 

 

 

C

 

 

 

 

 

FranÁais

R

 

 

 

 

 

SR

 

 

 

SL

 

 

 

SW

 

 

 

 

 

Italiano

0.3 9.0

 

3.0

 

 

 

 

 

 

 

 

 

 

Dolby

Digital DTS

 

 

 

Nederlands

 

 

 

 

 

 

 

 

 

DRC OFF

 

 

 

 

 

 

 

 

 

 

 

 

EspaÒol

DRC MID

 

 

 

 

 

DRC HIGH

 

 

 

 

 

 

 

 

 

 

1 12 FM 35

2

3

SHIFT+TEST TONE /

ENTER

25

ChH

07

7

 

3 ENTER

HOME MENU

能影響影像呈現的設定值。

1 HOME MENU

2/ / / ENTER

亮度0000

ñ20 +20

ñ16 +16

9 9

ñ9 +9

/

 

 

0

26

ChH

8

1DVD/CD

2 HOME MENU

3 / / / ENTER

明。1

 

 

 

 

 

 

 

4:3 (Letter Box)

4:3

39

 

 

 

 

 

4:3 (Pan & Scan)

4:3

 

 

 

 

 

 

 

 

 

16:9 (Wide)

 

 

 

 

 

 

 

32

 

 

 

 

 

 

ENTER

 

 

 

RETURN

 

 

 

 

 

 

 

 

 

 

 

08

EspaÒol Nederlands Italiano FranÁais English

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

43

 

 

 

 

 

 

1

DVD DVD

27

ChH

08

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

43

 

 

 

 

 

 

DVD

 

DVD

 

 

 

 

 

 

 

 

DVD

 

 

 

 

 

43

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ñ

 

 

 

 

DivX(R) VOD

Display

DivX®VOD

 

 

 

 

 

 

us 2119

 

DVD

 

DVD-Video

 

 

1

 

 

1

43

28

ChH

 

08

 

 

 

 

 

 

 

DivX (R) VOD

 

 

 

 

 

 

 

2 4

ENTER

密碼。

1

ENTER

2ENTER

2

ENTER

3ENTER

1

44

1

ENTER

2 ENTER

/

字鍵輸入4

 

English

 

 

DivX®VOD

DivX VOD

DivX VOD

 

 

 

DivX VOD

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FranÁais

 

 

 

 

 

 

 

 

• DivX VOD DRM( )

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Italiano

 

 

 

 

 

DivX VOD

 

 

 

Authorization Error

 

 

 

 

 

 

 

 

 

 

 

DivX VOD

 

 

Nederlands

 

 

 

1 HOME MENU

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DivX (R) VOD

 

 

 

 

 

 

 

 

 

 

EspaÒol

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Display

 

 

 

 

 

 

 

 

DivX (R) VOD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 Display

8

DivX VOD

1 43

29

ChH

08

DivX VOD

DivX VOD DivX VODDivX VOD0

Rental Expired

DivX VOD

30

ChH

9

AM 5 6

 

 

 

 

 

 

 

5 6

 

 

AM LOOP

FM PALFM

ANTENNA

PAL

MD

COMPONENT

LINE

FRONT R

VIDEO

CB/

 

L

PB

 

Y

R

SURROUND R

VIDEO OUT

AUDIO IN

S

09

LINE AUDIO IN

 

 

English

 

 

 

 

 

 

 

RCA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S-video

 

 

 

S-video

 

 

 

 

 

FranÁais

S-video

S-video S-VIDEO OUT

 

 

 

 

 

 

Italiano

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S-VIDEO

 

 

 

 

 

 

 

Nederlands

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ANTENNA

 

 

CB/

EspaÒol

 

 

CR/

 

 

 

COMPONENT

PR

 

 

 

VIDEO

 

 

 

VIDEO

 

PB

 

 

FM

 

 

 

AM LOOP

UNBAL75

 

 

 

IN

S-VIDEO

 

Y

 

 

 

 

MCACC

VIDEO OUT

MIC CONTROL

31

ChH

09

用這些端子代替標準視頻輸出來連接本系統至 您的電視機上。1

COMPONENT

VIDEO OUT

 

 

 

 

 

 

 

 

 

 

ANTENNA

 

 

CR/

 

 

COMPONENT

PR

 

 

VIDEO

 

 

VIDEO

 

 

CB/

 

 

 

PB

 

FM

 

 

 

AM LOOP

UNBAL75

 

 

 

 

IN

 

 

Y

 

S-VIDEO

 

 

MCACC

 

VIDEO

OUT

 

MIC

CONTROL

 

的影像。逐行掃描視頻僅可透過色差視頻輸出 端子輸出。

Macro Vision System Copy Guard 2

Pioneer

3 SR+ 4

 

 

 

CONTROL

 

 

OUT

 

 

 

Pioneer

ANTENNA

 

CR/

 

COMPONENT

PR

 

VIDEO

 

VIDEO

 

CB/

 

PB

FM

 

 

AM LOOP

UNBAL75

 

 

IN

Y

 

S-VIDEO

MCACC

 

VIDEO OUT

MIC

CONTROL

1 27

2 525

3 2003 Pioneer

4 Pioneer 3-ringed SR+ ADE7095 SR+

Pioneer

32

ChH

 

09

SR+

3-ringed SR+

CONTROL INCONTROL OUT 1

SR+ Pioneer

SR+

/ DVD LN LINE USB /

器上相對編號的視頻輸入。23 LN PDP3 TVTNNONE

5ENTER

Pioneer SR+

SR+ Pioneer

1SHIFT+SR+

2 /

ENTER

3/

VOL.C OFF

VOL.C ON DVD

SR+

1SHIFT+SR+

2 / SR+ ON

ENTER

SR+ SR+ OFF

SR+ SR+ SR+ ON

仍會保持SR+

1 CONTROL IN CONTROL OUT

2 PDP5 PC

EspaÒol Nederlands Italiano FranÁais English

33

ChH

10

10

相關的更多資訊。每個部分的第一項設定值皆 為預設值。

2 SHIFT+SETUP /

ENTER

1

3 / ENTER

能在您第一次插上電源時會啟動

DEMO ON

DEMO OFF

AM 9K

AM 10K

AUTO

置為AUTO

AUTO, PAL NTSC 2

• / TV SYS

2 ENTER

AUTO NTSC

NTSC PAL

PAL AUTO

WELCOME

3

 

 

 

 

 

 

NTSC

PAL

AUTO

 

 

 

 

 

 

 

 

 

 

DVD/ VCD/

NTSC

NTSC

PAL

NTSC

VCD/DivX

PAL

NTSC

PAL

PAL

 

 

 

 

 

 

CD/MP3/WMA/

ó

NTSC

PAL

NTSC

MPEG-4 AAC/

 

 

 

PAL

JPEG/

 

 

 

 

 

 

 

 

 

DTS CD

DTS CD

1

2 PAL 50 Hz (PAL)/60 Hz (NTSC)PAL TV V-Hold NTSCV-Hold

3 STANDBY/ON

34

ChH

 

10

NORMAL CD DTS CD

DTS-CD DTS CDCD

LOCK ON

LOCK OFF

您完全無須擔心。1

SLEEP

SLP ON

SLP OFF

SLP ON SLEEP12

S L P - - - - -

板顯示幕的亮度。

1 SHIFT+SETUP /

DIMMER ENTER

2 / ENTER

LIGHT

DARK

CD DVD

DVD-Video DVD-R DVD-RW

CD VCD

CD-R CD-RW

Fujicolor CD

DVD+R/+RW

Fuji Photo Film Co. Ltd.

DVD Format/Logo Licensing Corporation

KODAK Picture CD

IEC VCD

EspaÒol Nederlands Italiano FranÁais English

VIDEO

CD

Super Video CD( VCD)

1

35

ChH

10

DualDisc

DualDiscDVDDVD

DVD CD

Audio

DualDisc DVD DVDAudio

DualDisc

CD-R/RW CD-Audio VCD/ VCD ISO 9660 CD-ROM*

* ISO 9660 Level 1 2 CD Mode1 Mode2 XA Form1 Romeo Joliet

DVD-R/RW DVD-Video (Video )(VR)* UDF Bridge DVD-ROM

*

DVD-R/RW CD- R/RW

容。

MPEG-1 Audio Layer 3 (MP3) Windows Media Audio (WMA) MPEG-4 AAC

32 kHz / 44.1 kHz / 48 kHz

128 kbps

VBR MP3/WMA/MPEG- 4 AAC

WMA

DRM

DRM

.mp3 .wma .m4a MP3/ WMA/MPEG-4 AAC

299 648

JPEG Baseline JPEG EXIF 2.2*3072 x 2048

*

JPEG

.jpg JPEG

張碟片上最多可儲存299 648

DVD+R/DVD+RW

DVD-VideoDVD+R DVD+RW

DivX

DivX DivX, Inc. DivX®CD-R/RW DVD-R/RW/ROMDivX DVD-Video

36

ChH

 

10

DivX CD-R/RW DVD-R/RW

將會按字母的順序播放。

DivX

DivX®Certified

DivX® DivX® DivX® 6 1

.avi .divxDivX

.aviMPEG4 DivX

DivX

DivX 227

1 Albanian( ) (sq), Basque ( ) (eu), Catalan( ) (ca), Danish( ) (da), Dutch( ) (nl), English( ) (en), Faroese( ) (fo), Finnish( ) (fi), French( ) (fr), German( ) (de), Icelandic( ) (is), Irish( )(ga), Italian( ) (it), Norwegian ( )(no), Portuguese( ) (pt), Rhaeto-Romanic( ) (rm),

Scottish( ) (gd), Spanish( ) (es), Swedish( ) (sv)

2 Albanian( ) (sq), Croatian() (hr), Czech( ) (cs), Hungarian ( ) (hu), Polish( ) (pl), Romanian ( ) (ro), Slovak( ) (sk), Slovenian( ) (sl)

3 Bulgarian( ) (bg),

Byelorussian( ) (be), Macedonian()(mk), Russian( )(ru), Serbian( ) (sr), Ukrainian( ) (uk)

4 Hebrew( ) (iw), Yiddish ( ) (ji)

5 Turkish( ) (tr)

DivX DivX Certified

DivX, Inc.

MPEG-4 AAC

AAC Advanced Audio Coding MPEG-4 AAC

MPEG-2 AACMPEG-4 AACiTunes®.m4a AAC DRMiTunes®

Apple iTunes Apple Computer, Inc.

WMA

Windows Media®Windows Media Audio

EspaÒol Nederlands Italiano FranÁais English

1 4 GB .avi

2 .srt

.sub .ssa .smi

10

37

ChH

10

WMA Windows Media Audio Microsoft CorporationWMA Windows Media® Player version 7/7.1 Windows Media® Player for Windows® XP Windows Media® Player 9 Series

Microsoft Windows Media Windows Microsoft Corporation

面留下指紋、灰塵或刮痕。已經損壞或髒污的 碟片會影響播放的效能。

柔軟、乾燥的布料擦拭乾淨。

的方式擦拭碟片的表面。

的CD/DVD

寫用具在上面書寫。這樣會損壞碟片。

38

Pioneer

DVD Video

DVD Video DVD

ALL

...

架上

...

產生高熱的設備附近。

能會妨礙系統主機的正確散熱效果。

機四腳的表面上。

ChH

 

10

 

 

DVD

4:3 16:9 3

 

4:3 (Letter Box)

Pioneer

 

 

 

 

 

 

 

4:3 (Pan&Scan)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STANDBY/ON

 

GOOD BYE 1

 

 

 

 

 

DVD-Video4:3 7:3

CinemaScope 2

1 GOOD BYE

2 letterbox

3 4:3 16:9 (Wide) 4:3

4:3

16:9 letterbox

EspaÒol Nederlands Italiano FranÁais English

39

ChH

10

Pioneer

Pioneer

31

 

 

 

MUTE

25TUNER

AUTO STEREO VIRTUAL 14

96 kHz

7 30

CONTROL IN

SR+

TRAYLOCK

 

8

 

 

 

 

 

 

 

 

 

 

 

SND.

 

5

 

DEMO

 

 

 

 

 

 

 

 

 

 

40

ChH

 

10

DVD/CD/VCD

DVD-video38 DVD Video .

 

 

 

 

 

 

 

STANDBY/ON

 

 

 

 

 

 

 

S-video27

 

27

 

 

VCR AV

VCR AV

干擾到影像的播放。

Macro-Vision System

DVD CD DVD CD

CD-ROM CD-ROM ISO 966036

DVD-ROM DVD-ROM UDF bridge36

EspaÒol Nederlands Italiano FranÁais English

41

ChH

10

MP3 .mp3 WMA

.wma MPEG-4 AAC .m4a JPEG .jpg36

WMA DRM

MPEG-4 AAC

 

 

 

AM

 

AM 31

 

 

FM FM 31

34

USB

USB USB FAT16 FAT32

USB USB

MP3 .mp3 WMA.wma MPEG-4 AAC .m4a JPEG .jpg

WMA DRM

MPEG-4 AAC

 

 

 

 

2CH ONLY

 

 

 

96K

96 kHz

 

 

SND. DEMO

40

 

 

NOISY

MCACC

 

 

ERR MIC

MCACC

 

 

42

ChH

 

10

 

 

 

 

 

 

ERR SP

MCACC

 

 

 

 

MUTING

MUTE

 

 

 

 

STEREO

 

 

 

 

 

TRAYLOCK

40

 

 

 

 

KEY LOCK

35

 

 

 

 

PHONESIN

 

 

 

 

 

USB ERR

23 USB

 

 

 

 

 

 

EEP ERR

Pioneer

 

 

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

27

 

 

136

STANDBY/ON

 

 

 

USB

 

1

 

 

2

/

 

 

3

/

 

 

言種類及代碼的清單。

EspaÒol Nederlands Italiano FranÁais English

43

ChH

,,,

10

Japanese (ja), 1001

English (en), 0514

French (fr), 0618

German (de), 0405

Italian (it), 0920

Spanish (es), 0519

Dutch (nl), 1412

Russian (ru), 1821

Chinese (zh), 2608

Korean (ko), 1115

Greek (el), 0512

Afar (aa), 0101

Abkhazian (ab), 0102

Afrikaans (af), 0106

Amharic (am), 0113

Arabic (ar), 0118

Assamese (as), 0119

Aymara (ay), 0125

Azerbaijani (az), 0126

Bashkir (ba), 0201

Byelorussian (be), 0205

Bulgarian (bg), 0207

Bihari (bh), 0208

Bislama (bi), 0209

Bengali (bn), 0214

Tibetan (bo), 0215

Breton (br), 0218

Catalan (ca), 0301

Corsican (co), 0315

Czech (cs), 0319

Welsh (cy), 0325

Danish (da), 0401

Bhutani (dz), 0426

Esperanto (eo), 0515

Estonian (et), 0520

Basque (eu), 0521

Persian (fa), 0601

Finnish (fi), 0609

Fiji (fj), 0610

Faroese (fo), 0615

Frisian (fy), 0625

Irish (ga), 0701

Scots-Gaelic (gd), 0704

Galician (gl), 0712

Guarani (gn), 0714

Gujarati (gu), 0721

Hausa (ha), 0801

Hindi (hi), 0809

Croatian (hr), 0818

Hungarian (hu), 0821

Armenian (hy), 0825

Interlingua (ia), 0901

Interlingue (ie), 0905

Inupiak (ik), 0911

Indonesian (in), 0914

Icelandic (is), 0919

Hebrew (iw), 0923

Yiddish (ji), 1009

Javanese (jw), 1023

Georgian (ka), 1101

Kazakh (kk), 1111

Greenlandic (kl), 1112

Cambodian (km), 1113

Kannada (kn), 1114

Kashmiri (ks), 1119

Kurdish (ku), 1121

Kirghiz (ky), 1125

Latin (la), 1201

Lingala (ln), 1214

Slovak (sk), 1911

Laothian (lo), 1215

Slovenian (sl), 1912

Lithuanian (lt), 1220

Samoan (sm), 1913

Latvian (lv), 1222

Shona (sn), 1914

Malagasy (mg), 1307

Somali (so), 1915

Maori (mi), 1309

Albanian (sq), 1917

Macedonian (mk), 1311

Serbian (sr), 1918

Malayalam (ml), 1312

Siswati (ss), 1919

Mongolian (mn), 1314

Sesotho (st), 1920

Moldavian (mo), 1315

Sundanese (su), 1921

Marathi (mr), 1318

Swedish (sv), 1922

Malay (ms), 1319

Swahili (sw), 1923

Maltese (mt), 1320

Tamil (ta), 2001

Burmese (my), 1325

Telugu (te), 2005

Nauru (na), 1401

Tajik (tg), 2007

Nepali (ne), 1405

Thai (th), 2008

Norwegian (no), 1415

Tigrinya (ti), 2009

Occitan (oc), 1503

Turkmen (tk), 2011

Oromo (om), 1513

Tagalog (tl), 2012

Oriya (or), 1518

Setswana (tn), 2014

Panjabi (pa), 1601

Tonga (to), 2015

Polish (pl), 1612

Turkish (tr), 2018

Pashto, Pushto (ps), 1619

Tsonga (ts), 2019

Portuguese (pt), 1620

Tatar (tt), 2020

Quechua (qu), 1721

Twi (tw), 2023

Rhaeto-Romance (rm), 1813

Ukrainian (uk), 2111

Kirundi (rn), 1814

Urdu (ur), 2118

Romanian (ro), 1815

Uzbek (uz), 2126

Kinyarwanda (rw), 1823

Vietnamese (vi), 2209

Sanskrit (sa), 1901

Volapük (vo), 2215

Sindhi (sd), 1904

Wolof (wo), 2315

Sangho (sg), 1907

Xhosa (xh), 2408

Serbo-Croatian (sh), 1908

Yoruba (yo), 2515

Sinhalese (si), 1909

Zulu (zu), 2621

, 0118, ar, 0121, au, 0120, at, 0205, be, 0218, br, 0301, ca, 0312, cl, 0314, cn, 0411, dk

0609, fi 0618, fr 0405, de

, 0811, hk, 0914, in, 0904, id, 0920, it, 1016, jp, 1118, kr

, 1325, my, 1324, mx, 1412, nl, 1426, nz, 1415, no, 1611, pk

, 1608, ph, 1620, pt

, 1821, ru

, 1907, sg, 0519, es, 0308, ch, 1905, se, 2023, tw, 2008, th, 0702, gb, 2119, us

44

ChH

. . . . 100 W1 kHz 10 % T.H.D. 4 Ω

.. . 100 W 100 Hz 10 % T.H.D. 4 Ω

. . . DVD fs 96 kHz, 24-bit. . . . . . . .DVD VCD/ VCD

. . . . 4 Hz 44 kHz 96 kHz 4 Hz 22 kHz 48 kHz. . . . . . . . . . . . .± 0.001 % W.PEAK (JEITA)

FM

. . . . . . . 87.5 MHz 108 MHz. . . . . . . . . . . 75 Ω

AM

9 kHz . . . 531 kHz 1602 kHz10 kHz . . 530 kHz 1700 kHz. . . . . . . . . . . . . .

. . . . AC 110 V 240 V, 50 Hz 60 Hz

. . . . AC 220 V 240 V, 50 Hz 60 Hz. . . . . . . . . . . . . . 55 W. . . . . . . . . . . 0.29 W

. . . 420 x 60 x 330. . . . . . . . . . . . . . 3.3

DVD/CD

. . . . . . . . . . . . . . . . 1 2 R6 . . . . . . . . . . . . . 2. . . . . . . . . 1

AM . . . . . . . . . . . . . . . 1 FM . . . . . . . . . . . . . . . . 1Auto MCACC . . . . . 1

10

 

 

 

 

 

English

S-DV353

 

. . . . . . . .

.

 

. . . . . . . .

. 7.7 1-way

 

 

. . .7.7

 

. . . . . .

. . . . . . . . .4 Ω

 

. . . . . .

. . . 80 Hz 20 kHz

 

. . . .

. . . . . . . . 100 W

 

 

 

FranÁais

. . . 100 x 136 x 80

. . . . . . . .

. . . . . . 0.55

 

 

 

. . . . . . . .

.

 

 

. 7.7 1-way

 

Italiano

. . . . . . .

. . .7.7

. . . . . .

. . . . . . . . .4 Ω

 

. . . . . .

. . . 75 Hz 20 kHz

 

. . . .

. . . . . . . . 100 W

 

 

 

 

. . . . . . . .

. . .

Nederlands

. . .270 x 96 x 90

 

. . . . . . . .

. . . . . . 0.78

 

 

 

 

 

 

. . . . . . . .

. . 16 1-way

 

. . . . . . .

. . . 16

EspaÒol

 

. . . . . . . . .4 Ω

 

. . . . . .

. . . 30 Hz 2.5 kHz

 

. . . .

. . . . . . . . 100 W

 

 

 

 

. . . 190 x 360 x 320

 

. . . . . . . .

. . . . . . .4.0

 

. . . . . . . . . . . . . . 6

. . . . . 2

. . . . . . . . . . . . . 2. . . . . . . . . . . . 20. . . . . . . . . . . . . 4

45

ChH

10

S-DV555T

. . . . . . . .. . . . . . . . . . . . . 2-way

. . . . . . . . 7.7 x2. . . . . . . . . 2.6. . . . . . . . . . . . . . 4 Ω

. . . . . . . . . 70 Hz 20 kHz. . . . . . . . . . . 100 W

. . . 260 x 1096.5 x 260. . . . . . . . . . . . . . 4.2

. . . . . . . .. . . . . . . . . 7.7 1-way. . . . . . . . . 7.7. . . . . . . . . . . . . . 4 Ω

. . . . . . . . . 75 Hz 20 kHz. . . . . . . . . . . 100 W

. . .270 x 96 x 90. . . . . . . . . . . . . . 0.78

. . . . . . . .. . . . . . . . . 7.7 1-way. . . . . . . . . 7.7. . . . . . . . . . . . . . 4 Ω. . . . . . . . . 80 Hz 20 kHz. . . . . . . . . . . 100 W

. . . 100 x 136 x 80

. . . . . . . . . . . . . .

0.55

. . . . . . . . . . . . . 5. . . . . . . . . . . . . . 12. . . . . . . . . . . . . . 8. . . . . . . . . . . . . . 2. . . . . . . . . . . . . . . . . 2. . . . . . . . . . . . . . 2. . . . . . . . . . . . 6

46

S-DV1SW

SW

. . . . . . . . . . .. . . . . . . . . 16 1-way. . . . . . . . . . 16. . . . . . . . . . . . . . 4 Ω

. . . . . . . . 30 Hz 2.5 kHz. . . . . . . . . . . 100 W

. . . 220 x 421 x 402. . . . . . . . . . . . . . 6.0

. . . . . . . . . . . . . 1. . . . . . . . . . . . . . 6

另行通知。

NEC FontAvenue®

FontAvenue NEC

其他屬於MACROVISION CORPORATION

MACROVISION CORPORATION MACROVISION CORPORATION

DRM( )( )

ChH

Dolby LaboratoriesDolby Pro Logic D Dolby Laboratories

“DTS” “DTS Digital Surround”(Digital Theater Systems, Inc.)

10

EspaÒol Nederlands Italiano FranÁais English

47

ChH

PIONEER CORPORATION

4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC.

P.O. BOX 1540, Long Beach, California 90810-1540, U.S.A. TEL: (800) 421-1404

PIONEER ELECTRONICS OF CANADA, INC.

300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: 1-877-283-5901

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300

PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.

Blvd.Manuel Avila Camacho 138

10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270

<06C000001>

Printed in

<ARE7616-A>