XP 600 |
XP 1000 |
XP 2000 |
XP 2100 |
XP 3000 |
XP 3100 |
XP 5000 |
XP 5100 |
POWER AMPLIFIER
AMPLIFICADOR DE POTENCIA
English / Español /
XP 5100
User’s Manual Manual del Usuario
XP 600/1000/2000/2100/3000/3100/5000/5100
POWER AMPLIFIER
AMPLIFICADOR DE POTENCIA
CONTENTS |
|
|
CONTENIDO |
|
|
|
|
|
|
|
|
|
|
|
|
INTRODUCTION |
4 |
|
INTRODUCCION |
11 |
|
|
18 |
|
|
||||||
FEATURES................................. |
4 |
|
CARACTERISTICAS........................ |
11 |
|
................................ |
18 |
INSTALLATION........................... |
4 |
|
INSTALACIÓN.................................. |
11 |
|
................................ |
18 |
FRONT PANEL DESCRIPTION.5 |
|
DESCRIPCIÓN DE PANEL FRONTAL... |
12 |
|
.............. |
19 |
|
REAR PANEL DESCRIPTION.... |
5 |
|
DESCRIPCIÓN DE PANEL DORSAL..... |
13 |
|
.............. |
19 |
SPECIFICATIONS...................... |
8 |
|
ESPECIFICACIONES...................... |
15 |
|
................................ |
21 |
DIMENSIONS........................... |
23 |
|
DIMENSIONES................................ |
23 |
|
................................ |
23 |
BLOCK DIAGRAMS.................. |
25 |
|
DIAGRAMAS DE BLOQUE.............. |
25 |
|
............................ |
25 |
|
|
|
|
|
|
|
|
Phonic preserves the right to improve or alter any information within this document without prior notice Phonic se reserva el derecho de mejorar o alterar cualquier información provista dentro de este documento sin previo aviso PHONIC
V1.0 11/28/2008
IMPORTANT SAFETY INSTRUCTIONS
The apparatus shall not be exposed to dripping or splashing and that no objects |
|
|
|
with liquids, such as vases, |
|
|
|||
|
|
shall be placed on the apparatus. The MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable.
Warning: the user shall not place this apparatus in the area during the operation so that the mains switch can be easily accessible.
1.Read these instructions before operating this apparatus.
2.Keep these instructions for future reference.
3.Heed all warnings to ensure safe operation.
4.Follow all instructions provided in this document.
5.Do not use this apparatus near water or in locations where condensation may occur.
6.Clean only with dry cloth. Do not use aerosol or liquid cleaners. Unplug this apparatus before cleaning.
. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including .
9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not into your outlet, consult an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plug, convenience receptacles, and the point where they exit from the apparatus.
11.Only use attachments/accessories by the manufacturer.
12.Use only with a cart, stand, tripod, bracket, or
table by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tipover.
13.Unplug this apparatus during lighting storms or when unused for long periods of time.
14.Refer all servicing to service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
CAUTION |
RISK OF ElECTRIC SHOCK |
DO NOT OPEN |
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, |
DO NOT REMOVE COVER (OR BACK) |
NO USER SERVICEABLE PARTS INSIDE |
REFER SERVICING TO QUALIFIED PERSONNEL |
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: To reduce the risk ofor electric shock, do not expose this apparatus to rain or moisture.
CAUTION: Use of controls or adjustments or performance of procedures other than those may result in hazardous radiation exposure.
INTRODUCTION
Thank you for choosing XP series power amplifier. The unit is designed to provide a good combination of power, audio clarity, reliability and durability. An efficient heat-dissipation system comprising a high-surface area heat sink coupled with two variable speed fans ensures quiet and reliable cooling. Good sound quality and sturdy construction make this unit ideal for a multitude of amplification tasks; from studio installations to mobile DJs, house of worship and touring bands. In order to get the best performance out of your XP series power amplifier, please read this user’ s manual carefully, and retain it for future reference.
FEATURES
●Advanced powerful performancethird generation circuitry design
●High continuous current output from robust toroidel transformer
●Switchable input peak limiter and selectable high pass filter
(30 Hz, 50 Hz) to reduce distortion and protect speakers
●Two front mounted detented gain controls
●User selectable low pass filters (XP2100, XP3100 and XP5100 only)
●Selectable stereo, parallel & bridge mono amp modes
●Ground Lift-switch to help against humming
●Signal level at -40, -20, -10, protect and clip LED indicators to monitor performance
●Bridge mono and parallel mode LEDs
●Fast Recovery design for lower distortion if clipping occurs
●Active balanced inputs for low noise
●XLR/TRS connectors for maximum input flexibility
●Barrier strip input connectors on the XP5000 and XP5100 for permanent installations
●Speakon and 5-way binding post speaker outputs
●2 ventilation variable speed fans
●Very rugged housing
●Fits a standard 19” rack
Installation
MOUNTING
The power amplifier can be installed in a standard 19-
inch equipment rack. It requires 3 units (5.25 inches) for the XP 2000/2100, XP 3000/3100, and 2 units (3.5
inches) for the XP600/1000 of vertical rack space and secures to the rack cabinet with four rack mount screws and cup washers. In a rack, it is best to mount
units one above the other, with at least a unit of space at least betweentwoamplifiers.Thisprovidesefficientairflowandsupport.
COOLING
Two variable-speed fans would start running as soon as the power is being turned on. Before mounting your amplifier, you should familiarizeyourselfwithitscoolingrequirements.Theairflowsfrom the front to the back, so it is important not to block the amplifier front air vents. If the amplifier is rack-mounted, leave some space in front of the rack to prevent heated air being drawn back into the front-to-back airflow. Airflow restrictions are the most common cause of inadequate cooling. They may result from improper mounting,bundles of powercords,clogged dust filters andclosed rack doors. Mount the amplifier to allow sufficient airflow out the front outlets to ensure your amplifier work properly.
WIRING
The balanced XLR and TRS input connectors will accept the line-level output of most devices for ultimate input convenience.
The amplifier built-in XLR andTRS connectors can be wired similarly for balanced or unbalanced, floating or ground-referenced sources. The output connector is a binding post with Speakon which provides an easy connection when using banana plugs, spade lugs or bare wires.
XP 600/1000/2000/2100/3000/3100/5000/5100
|
|
|
|
-16 |
-14 |
-16 |
-14 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
NORMAl |
60 |
ClIP/ |
-10 |
-32 |
-6 |
-32 |
|
6 |
-10 |
ClIP/ |
|
NORMAl |
SUB |
|
-20 |
60 |
SUB |
||||||||
90 |
lIMIT |
-20 |
|
|
|
|
|
lIMIT |
90 |
|||
WOOFER |
120 |
|
|
|
|
|
-40 |
120 |
WOOFER |
|||
|
PROTECT |
-40 |
|
|
|
0 |
|
PROTECT |
|
|||
|
|
|
0 |
POWER |
|
|
|
|||||
|
|
|
|
|
|
|
|
|
FRONT PANEL DESCRIPTION
1. CLIP/LIM LED (RED)
When the audio signal drives the amplifier output circuit beyond its power capability, it will clip. The peak limiter detects this and quickly reduces the gain to minimize the amount of overdrive, so as to preserve as much of the program dynamics as possible.
2. PROTECT LED (YELLOW)
The power amplifier features several types of protection to prevent damage to the circuitry during turn-on or fault conditions. The power-on protection relay prevents damaging thumps to the speakersasthepowercomeson.Whentheamplifierisswitched on, the protect LED will light for a few seconds, and then go out, indicating that the relay has closed, connecting the speakers to the amplifier.
The protect LED will also come on if the speaker terminals are short circuited, or the impedance of the load between them is too low. Under these circumstances, the protect LED will stay on until the fault condition is rectified.
If the amplifier’ s large heat sinks go down for thermal reasons, leavethepowerconnectedtotheamplifier,trytoimproveventilation, and reduce the gain. Without power, the fan cannot operate, and the amplifier will require longer to reach a low enough temperature to restart.
3. SIGNAL LED (GREEN)
Eachchannelofthepoweramplifierfeaturesasignallighttoshow that how much of an audio signal has been put in to the channel. The threshold for the indicator is -40dB, above that, noise will trigger the LED to light.
4. GAIN CONTROL
These two knobs are the level controls for each channel of the amplifier. The gain increases as the knob is turned clockwise.
This unit features detented gain controls.
5. POWER SWITCH
Although the XP series amplifiers feature power-on muting, it is always a good practice to reduce both the gain controls before turningon the amplifier. The powering-up procedure for an audio system should start from instruments and then mixer, and you should verify that all system operations are normal before turning on the amplifier.
6. SUBWOOFER SWITCH (XP2100/3100/5100 ONLY)
NORMAL/60/90/120Hz
Switching from normal to either 60Hz, 90Hz or 120Hz setting will add the dedicated low pass filter to the output path, which offers you a sub bass output to achieve a 3-way or more ways speaker system. When you activate this function, you will get the subwoofer frequency output below 60Hz, 90Hz or 120Hz only. On the XP5100 this switch is located on the rear of the amplifier.
7. DISPLAY
When the power is on, the PHONIC logo at the top of the front panel will light up in green.
When the amplifier is switched to the bridge mono mode, the bridge LED right next to the PHONIC logo will light up in red.
When the amplifier is switched to the parallel mode, the parallel
LED next to the bridge LED will light up in yellow.
XP 600/1000/2000/2100/3000/3100/5000/5100
REAR PANEL DESCRIPTION
8. FAN
These two variable speed fans automatically maintain safe internal temperature. Keep the front and rear vents clear to allow full airflow. Hot air will be drawn out the back of the amplifier, so it does not stay in the rack, and make sure plenty of cool air can enter the rack.
9. RESET BREAKER
With rated loads and output levels, the breaker should only shut down the amplifier in rare instances of catastrophic failure. The circuit breaker can also shut down the amplifier in cases where extremely low-impedance loads and high output levels result in a current draw that exceeds its rating.This feature is not included on the XP600.
10. POWER CORD
All units are shipped with an appropriate plug and cord for the required AC voltage. This product is equipped with a 3-wire grounding type plug. This is a safety feature and should not be
defeated. Check the AC voltage before connecting the plug.
11.CHASSIS GROUNDING CONNECTING POINT
Please refer to your local safety code for proper grounding.
12.OUTPUT CONNECTORS
A pair of versatile binding posts and Speakon connectors are provided for output connection to each channel. Loudspeakers can be easily connected using banana plugs, spade lugs, bare wires or Speakon connector. Spade lugs and bare wires should both be screwed down tightly to avoid a short circuit. The Speakon connector for channel 1 includes channel 1, channel 2
and bridged mono pin connecting points. A pin out information could be foundbeside the Speakon connector.
13. INPUT CONNECTORS
ThepoweramplifieroffersXLRandTRSinputconnectorsforyour connecting convenience. On the XP5000 and 5100, users will also find barrier strip inputs. Barrier strip inputs should be screwed down tight as to not let oxygen enter the connection. These are best used in long term or permanent installations.
14. GROUNDING - FLOATING SWITCH
This switch allows the circuit and chassis grounding to be separated in case of a grounding conflict. In normal use, the switch should be in the grounding on position. Lifting the grounding
(to what is called the floating position) may resolve the ground conflict,butitmeansthatcircuitgroundingdependsonotherconnected equipment. Deficiencies in other components’ grounding will affect the sound quality and cause a grounding loop hum. For the best combination of safety and performance, it is highly recommended to set the switch at the “grounding on” position.
15. LIMITER ON/OFF
This switch allows you to route the peak limiter circuit to the input signal. This function will reduce distortion and protect speakers. This switch is not included on the XP5000 or XP5100.
16. HPF
This switch can activate a 30Hz or 50Hz high pass filter, which will roll off signals below either 30 Hz or 50 Hz. This improves sub bass performance by limiting sub bass cone motion. It will make more power available for the speakers’ rated frequency range. This switch is not included on the XP5000 or XP5100.
XP 600/1000/2000/2100/3000/3100/5000/5100
17. PARALLEL / STEREO / BRIDGE MONO SWITCH
Turn off the power before changing the operation mode. In stereo operation, each channel of the amplifier runs independently with its own signal and speakers. When the switch is set to the parallel mode, the input of CH2 is paralleled with that of CH1. Then, CH1 and CH2 can drive their own speakers independently, but they will have the same source, that of CH1. In bridge mono operation, both channels can be configured to drive a single load with a single signal at twice the power. Use the following procedure to ensure the systems safety when switching from one mode to another:
1.Turn off the power of the amplifier
2.Put one speaker, of not less than 4 ohms impedance, across the red (+) output terminals of the amplifier.
3.Ensure that there is only one input signal connected to CH1.
4.Switch the amplifier to bridge mono.
5.Turn the gain controls of CH1 and CH2 to the extreme left and then turn on the amplifier.
6.Verify operation at low gain, and then turn up the CH1 gain to increase power to a desired level.
This switch is not included on the XP5000 or XP5100.
18 . M O D E SW ITCH ES ( X P5 0 0 0 |
/ X P510 0 |
o nl y) |
XP 600/1000/2000/2100/3000/3100/5000/5100 |
|
SPECIFICATIONS
|
XP 600 |
|
XP 1000 |
XP 2000 / XP 2100 |
XP 3000 / XP 3100 |
Stereo Mode (driving both channels) |
|
Continuous Average Output Power Per Channel |
|||
8Ω 20Hz-20KHz 0.03% THD |
125W |
|
250W |
400W |
600W |
4Ω 20Hz-20KHz 0.05% THD |
200W |
|
400W |
600W |
1000W |
|
|
|
|
|
|
8Ω EIA 1KHz 1% THD |
140W |
|
275W |
450W |
650W |
4Ω EIA 1KHz 1% THD |
220W |
|
440W |
660W |
1100W |
2Ω EIA 1KHz 1% THD |
280W |
|
560W |
960W |
1400W |
Bridge Mono Mode |
|
|
Continuous Average Output Power |
|
|
8Ω 20Hz-20KHz 0.1% THD |
400W |
|
800W |
1200W |
2000W |
4Ω 1KHz 1% THD |
560W |
|
1120W |
1920W |
2800W |
All Models |
|
|
|
|
|
Input sensitivity @ 8 |
1 Vrms |
|
1.4 Vrms |
1.73 Vrms |
|
Input sensitivity @ 4 Ω |
0.9 Vrms |
|
1.25 Vrms |
1.23 Vrms |
1.58 Vrms |
|
|
|
|
|
|
Noise (unweighted 20Hz-20KHz below rated |
|
106 dB |
107 dB |
||
output) |
|
||||
|
|
|
|
|
|
Distortion (SMPTE-IM) |
|
<0.01% |
<0.02% |
||
Damping Factor |
>200 @ 8Ω |
>500 @ 8Ω |
|||
Output Circuitry |
|
|
Class H Amplifier |
|
|
Filtering |
|
|
High pass filter (30Hz, 50Hz) |
|
|
Subwoofer output |
Selectable subwoofer crossover at 60Hz, 90Hz, 120Hz for subwoofer |
||||
|
|
|
output (XP 2100, XP 3100 only) |
|
|
Frequency Response |
|
20Hz-20KHz, 0/-1dB, -3dB points: 5Hz-100KHz |
|||
Input Impedance |
|
|
20 kΩ balanced, 10 kΩ unbalanced |
|
|
Cooling |
Dual continuous variable-speed fans, front-to-rear air flow |
||||
Connectors (each channel) |
Input: XLR & 1/4” TRS jacks |
Output: Speakon & binding posts |
|||
Indicators |
Power: Amber Phonic logo; Parallel: Green backlight icon; |
||||
|
|
Bridged: Red backlight icon; CLIP/LIM: Red LED; |
|||
|
PROTECT: Yellow LED Green LED for -10dB, -20dB and -40dB Signal Lights |
||||
Front panel controls |
CH1 & CH2 GAIN knobs with 41 detents; selectable low frequency crossover at 60Hz, |
||||
|
|
|
90Hz and 120Hz (XP 2100 and XP 3100 only) |
||
Amplifier Protection |
Short circuit, thermal, subsonic, RF protection, Output DC offset, Heatsink and |
||||
|
transformer over-heat protection, Power on/off muting, Soft start power on |
||||
Gain |
32x (30dB) |
40x (32dB) |
|||
Power Consumption |
150W |
|
293W |
880W |
1460W |
Dimensions (WxHxD) |
482.6 x 89 x 367.2mm |
482.6 x 133.5 x 376mm |
|||
|
19" x 3.5" x 14.4" |
19" x 5.25" x 14.8" |
|||
Weight |
15kg (33lbs) |
|
16kg (35.2lbs) |
21kg (46.3lbs) |
23.3kg (51.3lbs) |
XP 600/1000/2000/2100/3000/3100/5000/5100
|
|
|
|
|
|
|
|
|
|
|
|
|
XP5000 / 5100 |
|
|
Stereo Mode (both channels driven) |
Continuous Average Output Power Per channel |
|
|
8 ohms FTC 20Hz-20kHz 0.1% THD |
1050 |
|
|
4 ohms FTC 20Hz-20kHz 0.1% THD |
1600 |
|
|
2 ohms FTC 20Hz-20kHz 0.1% THD |
2000 |
|
|
8 ohms EIA 1kHz 0.1% THD |
1100 |
|
|
4 ohms EIA 1kHz 0.1% THD |
1800 |
|
|
2 ohms EIA 1kHz 1% THD |
2500 |
|
|
Bridge Mono Mode |
Continuous Average Output Power |
|
|
8 ohms FTC 20Hz-20kHz 0.1% THD |
3200 |
|
|
8 ohms EIA 1kHz 0.1% THD |
3600 |
|
|
4 ohms EIA 1kHz 1% THD |
5000 |
|
|
All Models |
|
|
|
Subwoofer output |
Selectable subwoofer crossover at 60Hz, 90Hz, 120Hz |
|
|
|
(XP5100 only) |
|
|
Distortion (SMPTE-IM) |
<0.02% |
|
|
Distortion (Typical) 20Hz-20kHz: 10dB |
<0.02% |
|
|
below rated power |
|
|
|
|
|
|
|
Distortion (Typical) 1kHz and below: full |
<0.02% |
|
|
rated power |
|
|
|
Frequency Response |
20Hz-20kHz, 8 ohms, LF filter bypassed, +0/-1dB |
|
|
|
5Hz to 50kHz, 8ohms, LF filter bypassed, +0/-3 dB |
|
|
Damping Factor |
>250 @ 8 ohms |
|
|
Noise (unweighted) |
100 dB below rated output (20 Hz to 20kHz, 8 ohms load) |
|
|
Input sensitivity |
1.42 Vrms for 1000 watts into 8 ohms |
|
|
Control Font |
AC power switch, Ch1 & Ch2 gain control with 41 detents |
|
|
Control Rear |
12-poleDIPswitchfeaturinghighpassfilteron/off,highpassfilter30/50Hz,ClipLimiter |
|
|
|
on/off control for each channel and switches for selecting Stereo, Parallel, or Bridge |
|
|
|
Mode. Push-button circuit breaker for each channel. Slide switch for Grounding / |
|
|
|
Floating (Selectable low pass filter frequency at 60Hz, 90Hz and 120Hz, XP5100 only) |
|
|
Voltage Gain |
41x (36dB) |
|
|
Input Impedance |
20k ohms balanced, 10k ohms unbalanced |
|
|
Indicators |
Power-On: Amber Phonic logo; Parallel: Green backlight icon; Bridged: Red back- |
|
|
|
light icon; CLIP/LIM: Red LED; |
|
|
|
PROTECT: Yellow LED Green LED for -10dB, -20dB and -40dB Signal Lights |
|
|
Connectors Input |
XLR, 1/4”TRS jacks and barrier strip |
|
|
Connectors Output |
Binding posts and speakon outputs (Ch1 speakon wired for biamp) |
|
|
Cooling |
Continuous variable-speed fan, rear-to-front air flow |
|
|
Amplifier Protection |
Short circuit, open circuit, thermal, ultrasonic, and RF protection. Stable into mis- |
|
|
|
matched loads |
|
|
Load Protection |
on/off muting, DC fault output crowbar |
|
|
Output Circuitry |
Calss H Amplifier |
|
|
Power Requirements (depends on region) |
100-120VAC, 220-240VAC (+/- 10%), 50/60Hz (factory configured); 120V model |
|
|
|
requires 20 amp |
|
|
Circuit Breakers |
two (one for each channel): 100 and 120V models: 20 amp / 230 V models: 10 amp |
|
|
Dimensions (WxHxD) |
482.6 x 133 x 415 mm (19” x 5.2” x 16.3”) |
|
|
Weight |
28.2 kg (62.1 lbs) |
|
|
XP 600/1000/2000/2100/3000/3100/5000/5100