Parkside PMDS 100 A1 Operation And Safety Notes
IAN 115753
MODELLING DOUBLE BENCH GRINDER
PMDS 100 A1
MODELLBAU-DOPPELSCHLEIFER
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
MODELLING DOUBLE
BENCH GRINDER
Operation and Safety Notes
Translation of the original instructions
Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the
device.
Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend
mit allen Funktionen des Gerätes vertraut.
GB / IE Operation and Safety Notes Page 5
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 13
BA
11 10
21
3
5
4 b
4 a
12
12
2
7
9
6
8
4 d 4 e4 c
4 e
2
8
3
8
4
6
2
4
4 f 4 g
D
C
F
E
13 14
G
9
4 a 151716 5
5 GB/IE
Table of contents
Introduction
Intended use ........................................................................................................................................ Page 6
Features ...............................................................................................................................................Page 6
Scope of delivery ................................................................................................................................ Page 6
Technical Data ....................................................................................................................................Page 6
General power tool safety warnings
Working safely .................................................................................................................................... Page 7
Safety notices specific to the device ..................................................................................................Page 8
Before use
Working instructions ...........................................................................................................................Page 9
Dust extraction .....................................................................................................................................Page 9
Start-up
Switching on / off ................................................................................................................................Page 9
Attach the polishing mandrel ..............................................................................................................Page 10
Changing the grinding disk ................................................................................................................ Page 10
Maintenance and Cleaning .............................................................................................. Page 10
Service centre ..............................................................................................................................Page 10
Warranty ......................................................................................................................................... Page 11
Disposal ............................................................................................................................................ Page 11
Translation of the original declaration of conformity /
Manufacturer ............................................................................................................................... Page 12
6 GB/IE
Introduction
Modelling double bench grinder
PMDS 100 A1
Introduction
Congratulations on your purchase. You have sel
ected
a high quality product. The instructions for use are
a part of this product. They contain important information about safety, use and disposal. Before using the product, please familiarise yourself with all
the operating and safety instructions. Use the product
only as described and for the specified applications.
When passing this product on to others please be
sure to also include all of its documentation.
Intended use
The model-making bench grinder is intended for
grinding and polishing a wide range of materials.
It is suitable for grinding hard materials such as hard
metals, grey iron, HSS, ceramics and glass, as well
as softer materials such as copper, aluminium and
plastics. Tough materials, such as unhardened steel,
welded joints, hardened steel and titanium can also
be worked. The device is not intended for commercial use. Any other uses, and / or modifications to the
tool are considered improper use and may result in
serious hazards. The manufacturer is not liable for
damage caused by improper use.
Features
1
Spindle-lock key
2
Protective cover
3
Tommy screw for protective cover
4 a
Grinding disk (Grain size 80)*
4 b
Grinding disk (Grain size 100)*
4 c
Plastic polishing disk
4 d
Cotton disk
4 e
Felt polishing disk
4 f
Steel-wire brush
4 g
Brass-wire brush
5
Cap
6
Workpiece support
7
Mains lead
8
Knurled screw for workpiece support
9
Grinding dust compartment
10
ON / OFF switch
11
Rotational speed control
12
Polishing mandrel
13
Shaft
14
Centring flange
15
Safety washer
16
Union nut
17
Retaining screw
* installed
Scope of delivery
Immediately after unpacking the device
check the contents of delivery:
1 Modelling double bench grinder PMDS 100 A1
1 Polishing mandrel
1 Polishing set (five pieces, approx. 50 mm diameter):
- Cotton disk for high polish finish
- Plastic polishing disk for coarse sanding of
metals, such as stainless steel
- Felt polishing disk for processing paint
- Steel-wire brush for rust removal and cleaning
steel and non-ferrous metals
- Brass-wire brush for polishing non-ferrous metals
and precious metals
1 Set of instructions for use
Technical Data
Modelling double bench grinder:
Parkside PMDS 100 A1
Rated input voltage: 230–240 V∼, 50 Hz
Power input: 100 W*
Protection class: II /
IP code: IP 20
Rotational speed n
0
: 3000–9000 min
-1
Working speed: 8–24 m / s
7 GB/IE
Introduction / General power tool safety warnings
Weight (incl. accessories): 1750 g
*After a continuous operating time of 20 minutes, a
rest period is enabled, until the device has cooled to
a temperature within 2 K (2 °C) of the room temperature.
Grinding discs
Outside diameter: Ø 50 mm
Drill hole: Ø 12.7 mm
Thickness: 13 mm
Hardness: M
Grain size: 100 / 80
Noise and vibration data:
Measured sound value determined according to
EN 61029. The A-rated noise level of the power
tool is typically:
Noise level L
pA
: < 70 dB(A)
Uncertainty: 3 dB
Sound power level L
WA
: 76 dB(A)
Uncertainty: 3 dB
Wear ear protection!
Total vibration values in accordance with EN 61029:
Vibration emission value a
h
≤ 2.5 m / s
2
Uncertainty K = 1.5 m / s
2
Note: The vibration level specified in these instructi
ons
was measured in accordance with a standardised
measurement process and can be used to compare
tools. The vibration emission value specified can also
serve as a preliminary assessment of the exposure.
Different uses of the device give
rise to different vibration levels and in many cases
they may exceed the values given in these instructions.
It is easy to underestimate the vibration load if the
electrical power tool is used regularly in particular
circumstances.
If you wish to make an accurate assessment of the
vibration loads experienced during a particular period of working, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can result in a much lower vibration load over
the whole of the period of working.
General power tool
safety warnings
Read all safety
warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and / or
serious injury.
Save all warnings and instructions for
future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated (cordless) power tool.
Working safely
Keep the area you are working in tidy.
Untidiness in the working area can cause accidents.
Consider external influences! Never
expose electronic devices to rain. Do not use
electronic devices in damp or wet surroundings.
Ensure that the working area is well lit. Do not
use electronic devices in areas where there is a
risk of fire or explosions.
Protect yourself against electric shocks!
Avoid bodily contact with earthed parts (e.g.
pipes, radiators, electric ovens, refrigerators).
Keep other people away! Do not allow
other persons, particularly children, to touch
Loading...