Panasonic ER-VAJK Installation Manual
Thank you very much for using SUNX products.
Please read this Instruction Manual carefully and
thoroughly for the correct and optimum use of this
INSTRUCTION MANUAL
product. Kindly keep this manual in a convenient
place for quick reference.
Exclusive Nozzle for ER-VS01
Shape-preserving tube joint nozzle
ER-VAJK
1
OUTLINE
٨
This product is the exclusive nozzle for the ultra-compact ionizer spot type (ER-VS01).
٨
Since the shape-preserving tube (ER-VAKغ) can be bent freely and its form is maintained, ionized air can
be directed to the desired position.
2
SPECIFICATIONS
Shape-preserving tube joint nozzle
٨
Model No.
Item
Air pressure range
Material
Consumption air flow
Accessories
3
MOUNTING
٨
On the ultra-compact ionizer spot type (ER-VS01), a protective film is affixed on the nozzle fitting part.
Be sure to remove it before fitting the nozzle.
٨
The resin tube and the attachment are enclosed with the nozzle (ER-VAJK).
Mount them as decribed below.
Procedure
Ԙ
Insert the resin tube into the center of the nozzle.
ԙ
Direct the convex part of the center of the attachment towards you (see the right figure) and inserted it into ER-VS01.
Ԛ
In the state of Ԙinsert them into the nozzle fitting
part of ER-VS01 to mount. The tightening torque
should be 6N㨯m or less.
ԛ
Loosen the nut part of the nozzle (ER-VAJK) and fit
the tip of the tube
Ԝ
In the state of ԛinsert the tube into the nozzle
and tighten the nut and the nozzle. The tightening
torque should be 2N㨯m or less.
Note:
Be sure to fit the resin tube and the attachment.
When they are not fitted, the static removal is remarkably impaired.
Attachment (White): 1 pc., Resin tube: 1 pc.
(ER-VAKغ).
Shape-preserving tube
ER-VAKغ
ER-VAJK
0.02 to 0.5MPa
Stainless steel
30 to 250 /min.(ANR)
Shape-preserving tube
٨
Model No.
Item
Tube length
Material
Air pressure range
Allowable bending radius
ԛ
Shape-preserving tubeER-VAKغ
ER-VAK10
112mm
Inside tube: Aluminum
Tube sheath: High density polyethylene
End cap: Stainless steel
Convex part
Ԛ
Ԝ
Nut part of ER-VAJK
ER-VAK30 ER-VAK50
312mm 512mm
0.02 to 0.5MPa
40mm or more
ER-VS01
Protective film
ԙ
Ԙ
Attachment
Resin tube
Shape-preserving tube
joint nozzle (ER-VAJK)
Enclosed with
ER-VAJK
4
CAUTIONS
٨
The static removal efficiency depends upon the air pressure value. Use the product by the appropriate air pressure.
٨
Be sure to use an attachment suitable for nozzle.
٨
The shape-preserving tube (ER-VAKغ) is consumables. Replace it when fading or cracking etc. occurs
due to deterioration, or the coating inside the tube flakes off.
٨
Bending radius of the shape-preserving tube (ER-VAKغ) must be R40mm or more. However, do not bend
within 25mm from the both ends of the tube.
٨
Check the tightening state of the shape-preserving tube (ER-VAKغ) periodically. If the tube (ER-VAKغ)
and the nozzle (ER-VAJK) are loose, ion-balance and the static removal efficiency deteriorate.
5
DIMENSIONS (Unit: mm)
٨ ER-VAJK / Shape-preserving tube joint nozzle
M141
31.2 7.7
٨ ER-VAKغ/ Shape-preserving tube
10.8
25
This range must
not be bent.
Ǿ10
A
Nylon sleeve
25
This range must
not be bent.
Ǿ13
Model No. A
ER-VAK10
ER-VAK30 312
ER-VAK50
112
512
٨ Mounting drawing with ER-VS01
100
9.4
2-Ǿ4.5 mounting holes
http://www.sunx.co.jp/
PRINTED IN JAPAN
27
28
Model No. B C
ER-VAK10
ER-VAK30 429.3330
ER-VAK50
18.8
130
530
35.7
B
C
229.3
629.3
SUNX Limited
Head Office
2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901,
Japan
Phone: +81-(0)568-33-7211 FAX: +81-(0)568-33-2631
Overseas Sales Dept.
Phone: +81-(0)568-33-7861 FAX: +81-(0)568-33-8591
11.7
4.3
Loading...